RQUE SPECS2000-2026 Volkswagen Polo torque specs
1.5L TSI
These specs cover the Volkswagen Polo 1.5L TSI for model years 2000, 2001, 2002, 2003, 2004, 2005, 2006, 2007, 2008, 2009, 2010, 2011, 2012, 2013, 2014, 2015, 2016, 2017, 2018, 2019, 2020, 2021, 2022, 2023, 2024, 2025, 2026.
Change vehicle
Most looked up
- Lug nuts85 lb-ft115.2 Nm
- Oil drain plug22 lb-ft30 Nm
- Spark plugs22 lb-ft30 Nm
- Front caliper bracket bolts88 lb-ft120 Nm
- Rear caliper bracket bolts74 lb-ft100 Nm
- Front axle nut184 lb-ft250 Nm
- Outer tie rod end nut36.1 lb-ft49 Nm
Maintenance
Tire Rotation2 specs
- Lug Nuts - Alloy WheelsTorque in star pattern, recheck after 50 miles85 lb-ft115.2 Nm
- Lug Nuts - Steel WheelsTorque in star pattern85 lb-ft115.2 Nm
Brakes
Brake Caliper - Front3 specs
- Bleeder ScrewDo not overtighten7 lb-ft10 Nm
- Brake Line Banjo BoltUse new copper washers18 lb-ft25 Nm
- Caliper Bracket BoltsThreadlocker recommended88 lb-ft120 Nm
Brake Caliper - Rear3 specs
- Bleeder ScrewDo not overtighten7 lb-ft10 Nm
- Brake Line Banjo BoltUse new copper washers18 lb-ft25 Nm
- Caliper Bracket BoltsThreadlocker recommended74 lb-ft100 Nm
Brake Master Cylinder2 specs
- Brake Line FittingsUse flare nut wrench11 lb-ft15 Nm
- Master Cylinder Nuts18 lb-ft25 Nm
Brake Master Cylinder Rebuild3 specs
- Brake Line FittingsUse flare nut wrench11 lb-ft15 Nm
- Master Cylinder Mounting Nuts18 lb-ft25 Nm
- Reservoir Mounting Bolts6 lb-ft8 Nm
Brake Pads - Front3 specs
- Caliper Bracket BoltsThreadlocker recommended88 lb-ft120 Nm
- Caliper Slide Pin BoltsApply silicone brake grease26 lb-ft35 Nm
- Wheel Lug NutsTorque in star pattern85 lb-ft115.2 Nm
Brake Pads - Rear3 specs
- Caliper Bracket BoltsThreadlocker recommended74 lb-ft100 Nm
- Caliper Slide Pin BoltsApply silicone brake grease22 lb-ft30 Nm
- Wheel Lug NutsTorque in star pattern85 lb-ft115.2 Nm
Brake Pads and Rotors - Front3 specs
- Caliper Bracket Bolts73.8 lb-ft100 Nm
- Caliper Slide Pins26.6 lb-ft36 Nm
- Wheel Nuts84.1 lb-ft114 Nm
Brake Pads and Rotors - Rear3 specs
- Caliper Bracket Bolts73.8 lb-ft100 Nm
- Caliper Slide Pins25.8 lb-ft35 Nm
- Wheel Nuts83.3 lb-ft113 Nm
Brake Rotor - Front Single2 specs
- Brake Rotor Set Screw5.9 lb-ft8 Nm
- Caliper Bracket Bolts75.2 lb-ft102 Nm
Brake Rotor - Rear Single2 specs
- Brake Rotor Set Screw5.9 lb-ft8 Nm
- Caliper Bracket Bolts76 lb-ft103 Nm
Brake Rotors - Front Pair2 specs
- Brake Rotor Set Screw5.9 lb-ft8 Nm
- Caliper Bracket Bolts76.7 lb-ft104 Nm
Brake Rotors - Rear Pair2 specs
- Brake Rotor Set Screw5.9 lb-ft8 Nm
- Caliper Bracket Bolts75.2 lb-ft102 Nm
Front Brake Pad Replacement3 specs
- Caliper Bracket BoltsThreadlocker recommended88 lb-ft120 Nm
- Caliper Slide Pin BoltsApply silicone brake grease26 lb-ft35 Nm
- Wheel Lug NutsTorque in star pattern85 lb-ft115.2 Nm
Rear Brake Shoe Replacement3 specs
- Backing Plate Bolts44 lb-ft60 Nm
- Wheel Cylinder Bolts9 lb-ft12 Nm
- Wheel Lug NutsTorque in star pattern85 lb-ft115.2 Nm
Engine
Engine Mount - Front3 specs
- Engine Mount Through-Bolt63 lb-ft85 Nm
- Engine Mount-to-Block Bolts48 lb-ft65 Nm
- Engine Mount-to-Frame Bolts55 lb-ft75 Nm
Engine Mount - Rear1 spec
- Engine Mount Through-Bolt77.4 lb-ft105 Nm
Engine Mounts - All1 spec
- Engine Mount Through-Bolt73.8 lb-ft100 Nm
Exhaust Manifold Gasket3 specs
- Exhaust Manifold NutsApply anti-seize, work hot-to-cold22 lb-ft30 Nm
- Exhaust Manifold StudsIf replacing studs11 lb-ft15 Nm
- Heat Shield Bolts7 lb-ft10 Nm
Fan Belt Replacement3 specs
- Idler Pulley Bolt30 lb-ft40 Nm
- Tensioner Bolt18 lb-ft25 Nm
- Tensioner Pulley Bolt33 lb-ft45 Nm
Flywheel2 specs
- Flexplate BoltsAutomatic transmissions63 lb-ft85 Nm
- Flywheel BoltsOften TTY - check specs, tighten in star pattern70 lb-ft95 Nm
Full Engine Tune-Up4 specs
- Ignition Coil Bolt6 lb-ft8 Nm
- Spark Plugs - Aluminum HeadApply anti-seize to threads22 lb-ft30 Nm
- Throttle Body Bolts7 lb-ft10 Nm
- Valve Cover BoltsTighten in sequence7 lb-ft10 Nm
Head Gasket - Single6 specs
- Exhaust Manifold NutsApply anti-seize18 lb-ft25 Nm
- Intake Manifold BoltTighten in sequence18 lb-ft25 Nm
- Cylinder Head Bolts - Step 1Always use new TTY bolts30 lb-ft40 Nm
- Cylinder Head Bolts - Step 2Tighten in sequence59 lb-ft80 Nm
- Cylinder Head Bolts - Step 3Plus 90 degreesTurn 90°
- Cylinder Head Bolts - Step 4Plus 90 degreesTurn 90°
Head Gaskets - Both2 specs
- Head Bolts38.4 lb-ft52 Nm
- Intake Manifold19.2 lb-ft26 Nm
Intake Manifold Gasket3 specs
- Fuel Rail Bolts9 lb-ft12 Nm
- Intake Manifold BoltTighten in sequence from center out18 lb-ft25 Nm
- Throttle Body Bolts7 lb-ft10 Nm
Oil Change2 specs
- Oil Drain PlugUse new crush washer22 lb-ft30 Nm
- Oil Filter Housing CapFor cartridge-type filters18 lb-ft25 Nm
Oil Pan Gasket2 specs
- Oil Drain PlugUse new crush washer26 lb-ft35 Nm
- Oil Pan BoltTighten in sequence from center outward9 lb-ft12 Nm
Serpentine Belt2 specs
- Belt Tensioner Bolt41 lb-ft55 Nm
- Idler Pulley Bolt33 lb-ft45 Nm
Throttle Body2 specs
- Air Intake Hose Clamps2 lb-ft3 Nm
- Throttle Body Bolts7 lb-ft10 Nm
Transmission Mount2 specs
- Crossmember Bolt70 lb-ft95 Nm
- Transmission Mount Bolts48 lb-ft65 Nm
Valve Cover Gasket - Single2 specs
- Spark Plug Tube SealsIf equipped with separate seals9 lb-ft12 Nm
- Valve Cover BoltsTighten in sequence7 lb-ft10 Nm
Valve Cover Gaskets - Both1 spec
- Valve Cover Bolts8.9 lb-ft12 Nm
Cooling
Coolant Flush2 specs
- Block Drain PlugIf equipped, use new washer18 lb-ft25 Nm
- Drain PetcockPlastic - hand-tight only4 lb-ft5 Nm
Cooling Fan Clutch2 specs
- Flywheel Bolts59 lb-ft80 Nm
- Pressure Plate18.4 lb-ft25 Nm
Radiator4 specs
- Drain PetcockPlastic - hand tight4 lb-ft5 Nm
- Radiator Mounting BoltDo not overtighten plastic mounts9 lb-ft12 Nm
- Transmission Cooler LinesIf equipped18 lb-ft25 Nm
- Upper/Lower Hose Clamps2 lb-ft3 Nm
Radiator Removal and Service4 specs
- Drain PetcockPlastic - hand-tight only4 lb-ft5 Nm
- Fan Shroud Bolts7 lb-ft10 Nm
- Radiator Mounting BoltDo not overtighten plastic mounts9 lb-ft12 Nm
- Transmission Cooler LinesIf equipped, use new washers18 lb-ft25 Nm
Thermostat2 specs
- Coolant Temperature SensorUse thread sealant15 lb-ft20 Nm
- Thermostat Housing Bolt11 lb-ft15 Nm
Water Pump3 specs
- Hose ClampsSpring clamps preferred2 lb-ft3 Nm
- Thermostat Housing Bolt11 lb-ft15 Nm
- Water Pump BoltsTighten in criss-cross pattern18 lb-ft25 Nm
Ignition
Spark Plugs3 specs
- Ignition Coil Bolt6 lb-ft8 Nm
- Spark Plug22 lb-ft30 Nm
- Spark Plugs - Aluminum HeadApply anti-seize to threads22 lb-ft30 Nm
Fuel system
Fuel Filter2 specs
- Fuel Filter Bracket Bolt7 lb-ft10 Nm
- Fuel Line FittingsIf threaded type18 lb-ft25 Nm
Fuel Pump2 specs
- Fuel Pump Module Lock RingUse special tool59 lb-ft80 Nm
- Tank Strap Bolts26 lb-ft35 Nm
Electrical
Alternator4 specs
- Alternator Mounting Bolts37 lb-ft50 Nm
- Alternator Pivot Bolt18 lb-ft25 Nm
- Battery Terminal BoltsDo not overtighten6 lb-ft8 Nm
- Serpentine Belt Tensioner41 lb-ft55 Nm
Battery3 specs
- Battery Hold-Down Bolt6 lb-ft8 Nm
- Battery Terminal BoltsDo not overtighten - can crack terminal4 lb-ft6 Nm
- Battery Tray Bolts9 lb-ft12 Nm
Blower Motor2 specs
- Blower Motor Mounting Screw3 lb-ft4 Nm
- Blower Motor Resistor Screws1.5 lb-ft2 Nm
Starter3 specs
- Heat Shield BoltsIf equipped7 lb-ft10 Nm
- Starter Mounting BoltLong bolt may need extension37 lb-ft50 Nm
- Starter Solenoid NutFor B+ cable9 lb-ft12 Nm
Suspension
Ball Joint - Lower1 spec
- Lower Ball Joint Nut53.8 lb-ft73 Nm
Ball Joints - Upper and Lower1 spec
- Lower Ball Joint Nut52.4 lb-ft71 Nm
Control Arm Bushing - Front Lower2 specs
- Lower Ball Joint53.8 lb-ft73 Nm
- Pivot Bolts87 lb-ft118 Nm
Control Arm Bushing - Rear1 spec
- Pivot Bolts87 lb-ft118 Nm
Front Struts - Pair2 specs
- Pinch Bolt58.3 lb-ft79 Nm
- Strut Mount Nuts37.6 lb-ft51 Nm
Front Suspension Rebuild4 specs
- Ball Joint Pinch BoltUse new bolt if locknut style37 lb-ft50 Nm
- Lower Control Arm BoltsTorque at ride height81 lb-ft110 Nm
- Strut Top Mount Nuts18 lb-ft25 Nm
- Sway Bar End Link Nuts44 lb-ft60 Nm
Lower Control Arm - Front2 specs
- Lower Ball Joint51.6 lb-ft70 Nm
- Pivot Bolts91.5 lb-ft124 Nm
Rear Suspension Service3 specs
- Shock Lower Bolt52 lb-ft70 Nm
- Sway Bar End Link Nuts37 lb-ft50 Nm
- Trailing Arm BoltsTorque at ride height88 lb-ft120 Nm
Shock Absorber Replacement2 specs
- Lower Mount Bolt66 lb-ft90 Nm
- Upper Mount NutUse new self-locking nut41 lb-ft55 Nm
Strut Bearing2 specs
- Pinch Bolt60.5 lb-ft82 Nm
- Strut Mount Nuts36.1 lb-ft49 Nm
Strut Mount - Front2 specs
- Pinch Bolt57.5 lb-ft78 Nm
- Strut Mount Nuts36.9 lb-ft50 Nm
Sway Bar - Front1 spec
- Link Nuts38.4 lb-ft52 Nm
Sway Bar - Rear1 spec
- Link Nuts36.1 lb-ft49 Nm
Sway Bar Bushing - Front1 spec
- Link Nuts36.9 lb-ft50 Nm
Sway Bar Bushing - Rear1 spec
- Link Nuts36.1 lb-ft49 Nm
Sway Bar Link - Front1 spec
- Link Nuts38.4 lb-ft52 Nm
Sway Bar Link - Rear1 spec
- Link Nuts37.6 lb-ft51 Nm
Sway Bar Links - Front Pair1 spec
- Link Nuts38.4 lb-ft52 Nm
Steering
Tie Rod Assembly2 specs
- Jam Nut53.8 lb-ft73 Nm
- Tie Rod Nut36.1 lb-ft49 Nm
Tie Rod End - Inner2 specs
- Jam Nut50.2 lb-ft68 Nm
- Tie Rod Nut37.6 lb-ft51 Nm
Tie Rod End - Outer2 specs
- Jam Nut51.6 lb-ft70 Nm
- Tie Rod Nut36.9 lb-ft50 Nm
Tie Rods - Both Sides2 specs
- Jam Nut51.6 lb-ft70 Nm
- Tie Rod Nut36.1 lb-ft49 Nm
Drivetrain
CV Axle - Front2 specs
- Axle Nut214.6 lb-ft291 Nm
- Lower Ball Joint53.1 lb-ft72 Nm
CV Axles - Front Pair2 specs
- Axle Nut203.6 lb-ft276 Nm
- Lower Ball Joint52.4 lb-ft71 Nm
Limited Slip Clutch Pack2 specs
- Flywheel Bolts61.2 lb-ft83 Nm
- Pressure Plate18.4 lb-ft25 Nm
Wheel Bearing - Press-In Front2 specs
- Bearing Bolts49.4 lb-ft67 Nm
- Hub Nut212.4 lb-ft288 Nm
Wheel Bearing - Press-In Rear2 specs
- Bearing Bolts49.4 lb-ft67 Nm
- Hub Nut206.5 lb-ft280 Nm
Wheel Bearing Hub - Front6 specs
- ABS Sensor BoltDo not overtighten7 lb-ft10 Nm
- Axle NutUse new cotter pin after torque184 lb-ft250 Nm
- Bearing Bolts49.4 lb-ft67 Nm
- Caliper Bracket Bolts88 lb-ft120 Nm
- Hub Nut196.9 lb-ft267 Nm
- Wheel Bearing Hub BoltsApply threadlocker if specified81 lb-ft110 Nm
Wheel Bearing Hub - Rear5 specs
- Axle NutUse new cotter pin after torque148 lb-ft200 Nm
- Bearing Bolts50.2 lb-ft68 Nm
- Caliper Bracket Bolts81 lb-ft110 Nm
- Hub Nut213.9 lb-ft290 Nm
- Wheel Bearing Hub BoltsApply threadlocker if specified74 lb-ft100 Nm
Transmission
Clutch Cable2 specs
- Flywheel Bolts59 lb-ft80 Nm
- Pressure Plate19.2 lb-ft26 Nm
Clutch Disc2 specs
- Flywheel Bolts57.5 lb-ft78 Nm
- Pressure Plate17.7 lb-ft24 Nm
Clutch Hydraulic Line2 specs
- Flywheel Bolts58.3 lb-ft79 Nm
- Pressure Plate19.2 lb-ft26 Nm
Clutch Kit2 specs
- Flywheel Bolts61.2 lb-ft83 Nm
- Pressure Plate18.4 lb-ft25 Nm
Clutch Master Cylinder2 specs
- Flywheel Bolts58.3 lb-ft79 Nm
- Pressure Plate19.2 lb-ft26 Nm
Clutch Slave Cylinder2 specs
- Flywheel Bolts59.7 lb-ft81 Nm
- Pressure Plate18.4 lb-ft25 Nm
Transmission Fluid Change3 specs
- Transmission Drain PlugUse new crush washer if equipped22 lb-ft30 Nm
- Transmission Filter BoltsIf equipped with bolted filter6 lb-ft8 Nm
- Transmission Pan BoltsTighten in criss-cross pattern9 lb-ft12 Nm
Exhaust
Muffler2 specs
- Hanger Bracket Bolts18 lb-ft25 Nm
- Muffler Clamps41 lb-ft55 Nm
Heating and A/C
AC Clutch Coil2 specs
- Flywheel Bolts56.1 lb-ft76 Nm
- Pressure Plate19.2 lb-ft26 Nm
AC Compressor3 specs
- AC Compressor Bolts18 lb-ft25 Nm
- AC Line FittingsUse new O-rings, add PAG oil15 lb-ft20 Nm
- Clutch Connector Bolt6 lb-ft8 Nm
AC Compressor Clutch2 specs
- Flywheel Bolts56.8 lb-ft77 Nm
- Pressure Plate18.4 lb-ft25 Nm
AC Condenser2 specs
- AC Line FittingsUse new O-rings15 lb-ft20 Nm
- Condenser Mounting Bolts9 lb-ft12 Nm
Body
Hood Strut2 specs
- Pinch Bolt57.5 lb-ft78 Nm
- Strut Mount Nuts35.4 lb-ft48 Nm
Liftgate Strut2 specs
- Pinch Bolt58.3 lb-ft79 Nm
- Strut Mount Nuts35.4 lb-ft48 Nm
Torque is shown in lb-ft with Nm below it. Where a step says to turn, tighten the listed angle after the torque step before it. Use new bolts where the note says so.
Need labor times, fluids or repair steps for this car? See it on the Open Labor Project