1998 Toyota Mark II torque specs

3.0L I6 Twin-Turbo 2JZ-GTE

Change vehicle

Most looked up

Lug nuts105 lb-ft142.4 Nm
Oil drain plug26 lb-ft35 Nm
Spark plugs15 lb-ft20 Nm
Front caliper bracket bolts88 lb-ft120 Nm
Rear caliper bracket bolts74 lb-ft100 Nm
Front axle nut206.5 lb-ft280 Nm
Outer tie rod end nut40.6 lb-ft55 Nm

Maintenance

Differential Service3 specs
- Differential Cover Bolts22.1 lb-ft30 Nm
- Ring Gear Bolt81.1 lb-ft110 Nm
- Fill Plug25.8 lb-ft35 Nm
Tire Rotation2 specs
- Lug Nuts - Alloy WheelsTorque in star pattern, recheck after 50 miles105 lb-ft142.4 Nm
- Lug Nuts - Steel WheelsTorque in star pattern105 lb-ft142.4 Nm
Wheel Alignment2 specs
- Cam Bolt (adjustment)88.5 lb-ft120 Nm
- Tie Rod Lock Nut47.9 lb-ft65 Nm

Brakes

ABS Module2 specs
- ABS Module Mounting Bolt7.4 lb-ft10 Nm
- Brake Line Fitting11.1 lb-ft15 Nm
ABS Pump2 specs
- ABS Module Mounting Bolt7.4 lb-ft10 Nm
- Brake Line Fitting11.1 lb-ft15 Nm
Brake Caliper - Front3 specs
- Bleeder ScrewDo not overtighten7 lb-ft10 Nm
- Brake Line Banjo BoltUse new copper washers18 lb-ft25 Nm
- Caliper Bracket BoltsThreadlocker recommended88 lb-ft120 Nm
Brake Caliper - Rear3 specs
- Bleeder ScrewDo not overtighten7 lb-ft10 Nm
- Brake Line Banjo BoltUse new copper washers18 lb-ft25 Nm
- Caliper Bracket BoltsThreadlocker recommended74 lb-ft100 Nm
Brake Master Cylinder2 specs
- Brake Line FittingsUse flare nut wrench11 lb-ft15 Nm
- Master Cylinder Nuts18 lb-ft25 Nm
Brake Master Cylinder Rebuild3 specs
- Brake Line FittingsUse flare nut wrench11 lb-ft15 Nm
- Master Cylinder Mounting Nuts18 lb-ft25 Nm
- Reservoir Mounting Bolts6 lb-ft8 Nm
Brake Pads - Front3 specs
- Caliper Bracket BoltsThreadlocker recommended88 lb-ft120 Nm
- Caliper Slide Pin BoltsApply silicone brake grease26 lb-ft35 Nm
- Wheel Lug NutsTorque in star pattern105 lb-ft142.4 Nm
Brake Pads - Rear3 specs
- Caliper Bracket BoltsThreadlocker recommended74 lb-ft100 Nm
- Caliper Slide Pin BoltsApply silicone brake grease22 lb-ft30 Nm
- Wheel Lug NutsTorque in star pattern105 lb-ft142.4 Nm
Brake Pads and Rotors - Front4 specs
- Caliper Bracket Bolts73.8 lb-ft100 Nm
- Caliper Slide Pin25.8 lb-ft35 Nm
- Brake Rotor Set Screw3.7 lb-ft5 Nm
- Wheel Lug Nut105 lb-ft142.4 Nm
Brake Pads and Rotors - Rear4 specs
- Caliper Bracket Bolts66.4 lb-ft90 Nm
- Caliper Slide Pin25.8 lb-ft35 Nm
- Brake Rotor Set Screw3.7 lb-ft5 Nm
- Wheel Lug Nut105 lb-ft142.4 Nm
Brake Rotor - Front Single3 specs
- Caliper Bracket Bolts73.8 lb-ft100 Nm
- Caliper Slide Pin25.8 lb-ft35 Nm
- Wheel Lug Nut105 lb-ft142.4 Nm
Brake Rotor - Rear Single3 specs
- Caliper Bracket Bolts66.4 lb-ft90 Nm
- Caliper Slide Pin25.8 lb-ft35 Nm
- Wheel Lug Nut105 lb-ft142.4 Nm
Brake Rotors - Front Pair3 specs
- Caliper Bracket Bolts73.8 lb-ft100 Nm
- Caliper Slide Pin25.8 lb-ft35 Nm
- Wheel Lug Nut105 lb-ft142.4 Nm
Brake Rotors - Rear Pair3 specs
- Caliper Bracket Bolts66.4 lb-ft90 Nm
- Caliper Slide Pin25.8 lb-ft35 Nm
- Wheel Lug Nut105 lb-ft142.4 Nm
Front Brake Pad Replacement3 specs
- Caliper Bracket BoltsThreadlocker recommended88 lb-ft120 Nm
- Caliper Slide Pin BoltsApply silicone brake grease26 lb-ft35 Nm
- Wheel Lug NutsTorque in star pattern105 lb-ft142.4 Nm
Rear Brake Shoe Replacement3 specs
- Backing Plate Bolts44 lb-ft60 Nm
- Wheel Cylinder Bolts9 lb-ft12 Nm
- Wheel Lug NutsTorque in star pattern105 lb-ft142.4 Nm

Engine

Cylinder Head R&R1 spec
- Cylinder Head Bolt (TTY)55.3 lb-ft75 Nm
Cylinder Head Resurface1 spec
- Cylinder Head Bolt (TTY)55.3 lb-ft75 Nm
Engine Mount - Front3 specs
- Engine Mount Through-Bolt63 lb-ft85 Nm
- Engine Mount-to-Block Bolts48 lb-ft65 Nm
- Engine Mount-to-Frame Bolts55 lb-ft75 Nm
Engine Mount - Rear2 specs
- Engine Mount Through-Bolt62.7 lb-ft85 Nm
- Engine Mount Bracket Bolt55.3 lb-ft75 Nm
Engine Mounts - All2 specs
- Engine Mount Through-Bolt62.7 lb-ft85 Nm
- Engine Mount Bracket Bolt55.3 lb-ft75 Nm
Exhaust Manifold1 spec
- Exhaust Manifold Stud Nut29.5 lb-ft40 Nm
Exhaust Manifold Gasket3 specs
- Exhaust Manifold NutsApply anti-seize, work hot-to-cold22 lb-ft30 Nm
- Exhaust Manifold StudsIf replacing studs11 lb-ft15 Nm
- Heat Shield Bolts7 lb-ft10 Nm
Fan Belt Replacement3 specs
- Idler Pulley Bolt30 lb-ft40 Nm
- Tensioner Bolt18 lb-ft25 Nm
- Tensioner Pulley Bolt33 lb-ft45 Nm
Flexplate1 spec
- Flywheel/Flexplate Bolt70.1 lb-ft95 Nm
Flywheel3 specs
- Flexplate BoltsAutomatic transmissions63 lb-ft85 Nm
- Flywheel BoltsOften TTY - check specs, tighten in star pattern70 lb-ft95 Nm
- Flywheel/Flexplate Bolt70.1 lb-ft95 Nm
Full Engine Tune-Up5 specs
- Ignition Coil Bolt6 lb-ft8 Nm
- Spark Plugs - Aluminum HeadApply anti-seize to threads15 lb-ft20 Nm
- Spark Plugs - Cast Iron HeadApply anti-seize to threads22 lb-ft30 Nm
- Throttle Body Bolts7 lb-ft10 Nm
- Valve Cover BoltsTighten in sequence7 lb-ft10 Nm
Head Gasket - Single6 specs
- Exhaust Manifold NutsApply anti-seize18 lb-ft25 Nm
- Intake Manifold BoltTighten in sequence18 lb-ft25 Nm
- Cylinder Head Bolts - Step 1Always use new TTY bolts30 lb-ft40 Nm
- Cylinder Head Bolts - Step 2Tighten in sequence59 lb-ft80 Nm
- Cylinder Head Bolts - Step 3Plus 90 degreesTurn 90°
- Cylinder Head Bolts - Step 4Plus 90 degreesTurn 90°
Head Gaskets - Both1 spec
- Cylinder Head Bolt (TTY)55.3 lb-ft75 Nm
Intake Manifold2 specs
- Intake Manifold Bolt18.4 lb-ft25 Nm
- Throttle Body Bolt7.4 lb-ft10 Nm
Intake Manifold Gasket3 specs
- Fuel Rail Bolts9 lb-ft12 Nm
- Intake Manifold BoltTighten in sequence from center out18 lb-ft25 Nm
- Throttle Body Bolts7 lb-ft10 Nm
Oil Change2 specs
- Oil Drain PlugUse new crush washer26 lb-ft35 Nm
- Oil Filter (Spin-On)Hand tight plus 3/4 turn15 lb-ft20 Nm
Oil Pan Gasket2 specs
- Oil Drain PlugUse new crush washer26 lb-ft35 Nm
- Oil Pan BoltTighten in sequence from center outward9 lb-ft12 Nm
Oil Pan Replacement2 specs
- Oil Pan Bolt13.3 lb-ft18 Nm
- Oil Drain Plug29.5 lb-ft40 Nm
Serpentine Belt2 specs
- Belt Tensioner Bolt41 lb-ft55 Nm
- Idler Pulley Bolt33 lb-ft45 Nm
Serpentine Belt Tensioner1 spec
- Belt Tensioner Bolt29.5 lb-ft40 Nm
Throttle Body2 specs
- Air Intake Hose Clamps2 lb-ft3 Nm
- Throttle Body Bolts7 lb-ft10 Nm
Timing Belt5 specs
- Camshaft Sprocket Bolts59 lb-ft80 Nm
- Crankshaft Pulley BoltOften TTY - check specs133 lb-ft + 60°180 Nm
- Timing Belt Idler30 lb-ft40 Nm
- Timing Belt Tensioner26 lb-ft35 Nm
- Water Pump BoltsReplace with timing belt18 lb-ft25 Nm
Timing Belt Kit4 specs
- Camshaft timing pulley bolt59 lb-ft80 Nm
- Crankshaft Pulley Bolt243 lb-ft329 Nm
- Idler pulley bolt (No.2)32 lb-ft43 Nm
- Timing belt tensioner bolt19 lb-ft26 Nm
Timing Belt Tensioner3 specs
- Camshaft timing pulley bolt59 lb-ft80 Nm
- Crankshaft Pulley Bolt243 lb-ft329 Nm
- Timing belt tensioner bolt19 lb-ft26 Nm
Transmission Mount4 specs
- Crossmember Bolt70 lb-ft95 Nm
- Transmission Mount Bolts48 lb-ft65 Nm
- Transmission Mount Bolts59 lb-ft80 Nm
- Crossmember Bolt73.8 lb-ft100 Nm
Turbo Wastegate Actuator4 specs
- Turbo Mounting Stud Nut25.8 lb-ft35 Nm
- Oil Feed Line Banjo Bolt18.4 lb-ft25 Nm
- Oil Return Line Bolt11.1 lb-ft15 Nm
- Exhaust Flange Bolt25.8 lb-ft35 Nm
Turbocharger4 specs
- Turbo Mounting Stud Nut25.8 lb-ft35 Nm
- Oil Feed Line Banjo Bolt18.4 lb-ft25 Nm
- Oil Return Line Bolt11.1 lb-ft15 Nm
- Exhaust Flange Bolt25.8 lb-ft35 Nm
Valve Cover Gasket - Single2 specs
- Spark Plug Tube SealsIf equipped with separate seals9 lb-ft12 Nm
- Valve Cover BoltsTighten in sequence7 lb-ft10 Nm
Valve Cover Gaskets - Both1 spec
- Valve Cover Bolts8.9 lb-ft12 Nm

Cooling

Coolant Flush2 specs
- Block Drain PlugIf equipped, use new washer18 lb-ft25 Nm
- Drain PetcockPlastic - hand-tight only4 lb-ft5 Nm
Heater Core2 specs
- Heater Core Hose Clamp2.2 lb-ft3 Nm
- Dashboard Bolt7.4 lb-ft10 Nm
Radiator4 specs
- Drain PetcockPlastic - hand tight4 lb-ft5 Nm
- Radiator Mounting BoltDo not overtighten plastic mounts9 lb-ft12 Nm
- Transmission Cooler LinesIf equipped18 lb-ft25 Nm
- Upper/Lower Hose Clamps2 lb-ft3 Nm
Radiator Removal and Service4 specs
- Drain PetcockPlastic - hand-tight only4 lb-ft5 Nm
- Fan Shroud Bolts7 lb-ft10 Nm
- Radiator Mounting BoltDo not overtighten plastic mounts9 lb-ft12 Nm
- Transmission Cooler LinesIf equipped, use new washers18 lb-ft25 Nm
Thermostat2 specs
- Coolant Temperature SensorUse thread sealant15 lb-ft20 Nm
- Thermostat Housing Bolt11 lb-ft15 Nm
Thermostat Housing1 spec
- Thermostat Housing Bolt14.8 lb-ft20 Nm
Water Pump3 specs
- Hose ClampsSpring clamps preferred2 lb-ft3 Nm
- Thermostat Housing Bolt11 lb-ft15 Nm
- Water Pump BoltsTighten in criss-cross pattern18 lb-ft25 Nm

Ignition

Spark Plugs5 specs
- Ignition Coil Bolt6 lb-ft8 Nm
- Spark Plugs - Aluminum HeadApply anti-seize to threads15 lb-ft20 Nm
- Spark Plugs - Cast Iron HeadApply anti-seize to threads22 lb-ft30 Nm
- Spark Plug13.3 lb-ft18 Nm
- Ignition Coil Bolt5.9 lb-ft8 Nm

Fuel system

Fuel Filter2 specs
- Fuel Filter Bracket Bolt7 lb-ft10 Nm
- Fuel Line FittingsIf threaded type18 lb-ft25 Nm
Fuel Pump2 specs
- Fuel Pump Module Lock RingUse special tool59 lb-ft80 Nm
- Tank Strap Bolts26 lb-ft35 Nm
Fuel Pump Module2 specs
- Fuel Pump Lock Ring40.6 lb-ft55 Nm
- Fuel Line Fitting18.4 lb-ft25 Nm
Fuel Tank2 specs
- Fuel Tank Strap Bolt25.8 lb-ft35 Nm
- Fuel Filler Neck Clamp3.7 lb-ft5 Nm
Fuel Tank Strap2 specs
- Fuel Tank Strap Bolt25.8 lb-ft35 Nm
- Fuel Filler Neck Clamp3.7 lb-ft5 Nm
High Pressure Fuel Pump2 specs
- Fuel Pump Lock Ring40.6 lb-ft55 Nm
- Fuel Line Fitting18.4 lb-ft25 Nm

Electrical

Alternator4 specs
- Alternator Mounting Bolts37 lb-ft50 Nm
- Alternator Pivot Bolt18 lb-ft25 Nm
- Battery Terminal BoltsDo not overtighten6 lb-ft8 Nm
- Serpentine Belt Tensioner41 lb-ft55 Nm
Alternator Belt2 specs
- Alternator Mounting Bolt36.9 lb-ft50 Nm
- Alternator Pivot Bolt29.5 lb-ft40 Nm
Battery3 specs
- Battery Hold-Down Bolt6 lb-ft8 Nm
- Battery Terminal BoltsDo not overtighten - can crack terminal4 lb-ft6 Nm
- Battery Tray Bolts9 lb-ft12 Nm
Blower Motor2 specs
- Blower Motor Mounting Screw3 lb-ft4 Nm
- Blower Motor Resistor Screws1.5 lb-ft2 Nm
Blower Motor Control Module1 spec
- Blower Motor Mounting Screw3.7 lb-ft5 Nm
Blower Motor Resistor1 spec
- Blower Motor Mounting Screw3.7 lb-ft5 Nm
Door Lock Actuator - Front1 spec
- Door Latch Bolt7.4 lb-ft10 Nm
Door Lock Actuator - Rear1 spec
- Door Latch Bolt7.4 lb-ft10 Nm
Fuel Pump Relay2 specs
- Fuel Pump Lock Ring40.6 lb-ft55 Nm
- Fuel Line Fitting18.4 lb-ft25 Nm
Power Window Motor - Front2 specs
- Window Regulator Bolt7.4 lb-ft10 Nm
- Door Panel Screws2.2 lb-ft3 Nm
Power Window Motor - Rear2 specs
- Window Regulator Bolt7.4 lb-ft10 Nm
- Door Panel Screws2.2 lb-ft3 Nm
Power Window Regulator - Front2 specs
- Window Regulator Bolt7.4 lb-ft10 Nm
- Door Panel Screws2.2 lb-ft3 Nm
Power Window Regulator - Rear2 specs
- Window Regulator Bolt7.4 lb-ft10 Nm
- Door Panel Screws2.2 lb-ft3 Nm
Starter3 specs
- Heat Shield BoltsIf equipped7 lb-ft10 Nm
- Starter Mounting BoltLong bolt may need extension37 lb-ft50 Nm
- Starter Solenoid NutFor B+ cable9 lb-ft12 Nm
Starter Solenoid1 spec
- Starter Mounting Bolt40.6 lb-ft55 Nm
Window Motor and Regulator - Front2 specs
- Window Regulator Bolt7.4 lb-ft10 Nm
- Door Panel Screws2.2 lb-ft3 Nm
Window Motor and Regulator - Rear2 specs
- Window Regulator Bolt7.4 lb-ft10 Nm
- Door Panel Screws2.2 lb-ft3 Nm

Suspension

Air Spring/Air Bag3 specs
- Strut Tower Nut36.9 lb-ft50 Nm
- Strut Pinch Bolt66.4 lb-ft90 Nm
- Wheel Lug Nut105 lb-ft142.4 Nm
Ball Joint - Lower3 specs
- Ball Joint Pinch Bolt40.6 lb-ft55 Nm
- Lower Ball Joint Castle Nut70.1 lb-ft95 Nm
- Wheel Lug Nut105 lb-ft142.4 Nm
Ball Joint - Upper3 specs
- Ball Joint Pinch Bolt40.6 lb-ft55 Nm
- Upper Ball Joint Castle Nut70.1 lb-ft95 Nm
- Wheel Lug Nut105 lb-ft142.4 Nm
Ball Joints - Upper and Lower4 specs
- Ball Joint Pinch Bolt40.6 lb-ft55 Nm
- Lower Ball Joint Castle Nut70.1 lb-ft95 Nm
- Upper Ball Joint Castle Nut70.1 lb-ft95 Nm
- Wheel Lug Nut105 lb-ft142.4 Nm
Coil Spring - Front3 specs
- Strut Tower Nut36.9 lb-ft50 Nm
- Strut Pinch Bolt66.4 lb-ft90 Nm
- Wheel Lug Nut105 lb-ft142.4 Nm
Coil Spring - Rear3 specs
- Strut Tower Nut36.9 lb-ft50 Nm
- Strut Pinch Bolt66.4 lb-ft90 Nm
- Wheel Lug Nut105 lb-ft142.4 Nm
Coil Springs - Front Pair3 specs
- Strut Tower Nut36.9 lb-ft50 Nm
- Strut Pinch Bolt66.4 lb-ft90 Nm
- Wheel Lug Nut105 lb-ft142.4 Nm
Coil Springs - Rear Pair3 specs
- Strut Tower Nut36.9 lb-ft50 Nm
- Strut Pinch Bolt66.4 lb-ft90 Nm
- Wheel Lug Nut105 lb-ft142.4 Nm
Control Arm Bushing - Front Lower3 specs
- Control Arm Pivot Bolt88.5 lb-ft120 Nm
- Ball Joint Pinch Bolt40.6 lb-ft55 Nm
- Wheel Lug Nut105 lb-ft142.4 Nm
Control Arm Bushing - Front Upper3 specs
- Control Arm Pivot Bolt88.5 lb-ft120 Nm
- Ball Joint Pinch Bolt40.6 lb-ft55 Nm
- Wheel Lug Nut105 lb-ft142.4 Nm
Control Arm Bushing - Rear3 specs
- Control Arm Pivot Bolt88.5 lb-ft120 Nm
- Ball Joint Pinch Bolt40.6 lb-ft55 Nm
- Wheel Lug Nut105 lb-ft142.4 Nm
Front Struts - Pair3 specs
- Strut Tower Nut36.9 lb-ft50 Nm
- Strut Pinch Bolt66.4 lb-ft90 Nm
- Wheel Lug Nut105 lb-ft142.4 Nm
Front Suspension Rebuild5 specs
- Ball Joint Pinch BoltUse new bolt if locknut style37 lb-ft50 Nm
- Lower Control Arm BoltsTorque at ride height81 lb-ft110 Nm
- Strut Top Mount Nuts18 lb-ft25 Nm
- Sway Bar End Link Nuts44 lb-ft60 Nm
- Upper Control Arm BoltsTorque at ride height66 lb-ft90 Nm
Lower Control Arm - Front3 specs
- Control Arm Pivot Bolt88.5 lb-ft120 Nm
- Ball Joint Pinch Bolt40.6 lb-ft55 Nm
- Wheel Lug Nut105 lb-ft142.4 Nm
Lower Control Arm - Rear3 specs
- Control Arm Pivot Bolt88.5 lb-ft120 Nm
- Ball Joint Pinch Bolt40.6 lb-ft55 Nm
- Wheel Lug Nut105 lb-ft142.4 Nm
Rear Shocks - Pair3 specs
- Strut Tower Nut36.9 lb-ft50 Nm
- Strut Pinch Bolt66.4 lb-ft90 Nm
- Wheel Lug Nut105 lb-ft142.4 Nm
Rear Suspension Service4 specs
- Lower Control Arm BoltsTorque at ride height66 lb-ft90 Nm
- Shock Lower Bolt52 lb-ft70 Nm
- Sway Bar End Link Nuts37 lb-ft50 Nm
- Trailing Arm BoltsTorque at ride height88 lb-ft120 Nm
Shock Absorber Replacement2 specs
- Lower Mount Bolt66 lb-ft90 Nm
- Upper Mount NutUse new self-locking nut41 lb-ft55 Nm
Strut Assembly - Front4 specs
- Strut Mount Center NutHold strut shaft with Allen key41 lb-ft55 Nm
- Strut to Knuckle BoltsOften TTY111 lb-ft150 Nm
- Strut Tower NutsDo not loosen center nut unless compressed37 lb-ft50 Nm
- Sway Bar End Link Nuts41 lb-ft55 Nm
Strut Assembly - Rear3 specs
- Strut Tower Nut36.9 lb-ft50 Nm
- Strut Pinch Bolt66.4 lb-ft90 Nm
- Wheel Lug Nut105 lb-ft142.4 Nm
Strut Bearing3 specs
- Strut Tower Nut36.9 lb-ft50 Nm
- Strut Pinch Bolt66.4 lb-ft90 Nm
- Wheel Lug Nut105 lb-ft142.4 Nm
Strut Mount - Front3 specs
- Strut Tower Nut36.9 lb-ft50 Nm
- Strut Pinch Bolt66.4 lb-ft90 Nm
- Wheel Lug Nut105 lb-ft142.4 Nm
Strut Mount - Rear3 specs
- Strut Tower Nut36.9 lb-ft50 Nm
- Strut Pinch Bolt66.4 lb-ft90 Nm
- Wheel Lug Nut105 lb-ft142.4 Nm
Subframe1 spec
- Subframe Bolts110.6 lb-ft150 Nm
Subframe Bushing1 spec
- Subframe Bolts110.6 lb-ft150 Nm
Sway Bar Link - Front3 specs
- Sway Bar End Link Nuts40.6 lb-ft55 Nm
- Sway Bar Link Nuts44.3 lb-ft60 Nm
- Wheel Lug Nut105 lb-ft142.4 Nm
Sway Bar Link - Rear2 specs
- Sway Bar Link Nuts44.3 lb-ft60 Nm
- Wheel Lug Nut105 lb-ft142.4 Nm
Sway Bar Links - Front Pair2 specs
- Sway Bar Link Nuts44.3 lb-ft60 Nm
- Wheel Lug Nut105 lb-ft142.4 Nm
Upper Control Arm - Front3 specs
- Control Arm Pivot Bolt88.5 lb-ft120 Nm
- Ball Joint Pinch Bolt40.6 lb-ft55 Nm
- Wheel Lug Nut105 lb-ft142.4 Nm
Upper Control Arm - Rear3 specs
- Control Arm Pivot Bolt88.5 lb-ft120 Nm
- Ball Joint Pinch Bolt40.6 lb-ft55 Nm
- Wheel Lug Nut105 lb-ft142.4 Nm

Steering

Power Steering Pump8 specs
- High Pressure Hose FittingUse new O-rings18 lb-ft25 Nm
- Power Steering Pump Bolts18 lb-ft25 Nm
- Pressure Line FittingUse new O-rings22 lb-ft30 Nm
- Pulley NutHold pulley with pin spanner52 lb-ft70 Nm
- Pump Mounting Bolts18 lb-ft25 Nm
- Return Hose Clamp2 lb-ft3 Nm
- Return Line Clamp3 lb-ft4 Nm
- Serpentine Belt Tensioner41 lb-ft55 Nm
Power Steering Rack3 specs
- Steering Rack Bolts70.1 lb-ft95 Nm
- Tie Rod End Nut40.6 lb-ft55 Nm
- Steering Line Fitting18.4 lb-ft25 Nm
Tie Rod Assembly3 specs
- Tie Rod End Castle Nut40.6 lb-ft55 Nm
- Tie Rod Lock Nut47.9 lb-ft65 Nm
- Wheel Lug Nut105 lb-ft142.4 Nm
Tie Rod End - Inner3 specs
- Tie Rod End Castle Nut40.6 lb-ft55 Nm
- Tie Rod Lock Nut47.9 lb-ft65 Nm
- Wheel Lug Nut105 lb-ft142.4 Nm
Tie Rod End - Outer3 specs
- Tie Rod End Castle Nut40.6 lb-ft55 Nm
- Tie Rod Lock Nut47.9 lb-ft65 Nm
- Wheel Lug Nut105 lb-ft142.4 Nm
Tie Rods - Both Sides3 specs
- Tie Rod End Castle Nut40.6 lb-ft55 Nm
- Tie Rod Lock Nut47.9 lb-ft65 Nm
- Wheel Lug Nut105 lb-ft142.4 Nm

Drivetrain

Axle Shaft - Rear2 specs
- Axle Nut206.5 lb-ft280 Nm
- Wheel Lug Nut105 lb-ft142.4 Nm
CV Axle - Front2 specs
- Axle Nut206.5 lb-ft280 Nm
- Wheel Lug Nut105 lb-ft142.4 Nm
CV Axle - Rear2 specs
- Axle Nut206.5 lb-ft280 Nm
- Wheel Lug Nut105 lb-ft142.4 Nm
CV Axles - Front Pair2 specs
- Axle Nut206.5 lb-ft280 Nm
- Wheel Lug Nut105 lb-ft142.4 Nm
Differential Fluid Change - Rear3 specs
- Differential Cover Bolts22.1 lb-ft30 Nm
- Ring Gear Bolt81.1 lb-ft110 Nm
- Fill Plug25.8 lb-ft35 Nm
Differential Rebuild - Rear3 specs
- Differential Cover Bolts22.1 lb-ft30 Nm
- Ring Gear Bolt81.1 lb-ft110 Nm
- Fill Plug25.8 lb-ft35 Nm
Driveshaft - Front3 specs
- Center Support Bearing Bracket Bolts37 lb-ft50 Nm
- Driveshaft Flange Bolts (CV/U-Joint)Use new bolts if torque-to-yield55 lb-ft75 Nm
- Transfer Case Output Yoke NutIf accessible133 lb-ft180 Nm
Driveshaft - Rear3 specs
- Differential Pinion Yoke NutUse new nut, set pinion preload184 lb-ft250 Nm
- Driveshaft Flange Bolts55 lb-ft75 Nm
- U-Joint Strap BoltsApply threadlocker26 lb-ft35 Nm
Driveshaft Center Support Bearing2 specs
- Center Support Bearing Bracket Bolts37 lb-ft50 Nm
- Driveshaft Flange Bolts55 lb-ft75 Nm
Wheel Bearing - Press-In Front3 specs
- Hub Nut / Axle Nut206.5 lb-ft280 Nm
- Wheel Bearing Bolts55.3 lb-ft75 Nm
- Wheel Lug Nut105 lb-ft142.4 Nm
Wheel Bearing - Press-In Rear3 specs
- Hub Nut / Axle Nut206.5 lb-ft280 Nm
- Wheel Bearing Bolts55.3 lb-ft75 Nm
- Wheel Lug Nut105 lb-ft142.4 Nm
Wheel Bearing Hub - Front7 specs
- ABS Sensor BoltDo not overtighten7 lb-ft10 Nm
- Axle NutUse new cotter pin after torque184 lb-ft250 Nm
- Caliper Bracket Bolts88 lb-ft120 Nm
- Wheel Bearing Hub BoltsApply threadlocker if specified81 lb-ft110 Nm
- Hub Nut / Axle Nut206.5 lb-ft280 Nm
- Wheel Bearing Bolts55.3 lb-ft75 Nm
- Wheel Lug Nut105 lb-ft142.4 Nm
Wheel Bearing Hub - Rear6 specs
- Axle NutUse new cotter pin after torque148 lb-ft200 Nm
- Caliper Bracket Bolts81 lb-ft110 Nm
- Wheel Bearing Hub BoltsApply threadlocker if specified74 lb-ft100 Nm
- Hub Nut / Axle Nut184.4 lb-ft250 Nm
- Wheel Bearing Bolts55.3 lb-ft75 Nm
- Wheel Lug Nut105 lb-ft142.4 Nm

Transmission

Clutch Disc3 specs
- Pressure Plate Bolt25.8 lb-ft35 Nm
- Flywheel Bolts70.1 lb-ft95 Nm
- Transmission Bell Housing Bolt51.6 lb-ft70 Nm
Clutch Hydraulic Line2 specs
- Pressure Plate Bolt25.8 lb-ft35 Nm
- Transmission Bell Housing Bolt51.6 lb-ft70 Nm
Clutch Kit3 specs
- Pressure Plate Bolt25.8 lb-ft35 Nm
- Flywheel Bolts70.1 lb-ft95 Nm
- Transmission Bell Housing Bolt51.6 lb-ft70 Nm
Dual Mass Flywheel1 spec
- Flywheel/Flexplate Bolt70.1 lb-ft95 Nm
Flywheel Resurface1 spec
- Flywheel/Flexplate Bolt70.1 lb-ft95 Nm
Transmission Fluid Change3 specs
- Transmission Drain PlugUse new crush washer if equipped22 lb-ft30 Nm
- Transmission Filter BoltsIf equipped with bolted filter6 lb-ft8 Nm
- Transmission Pan BoltsTighten in criss-cross pattern9 lb-ft12 Nm

Exhaust

Catalytic Converter - Direct Fit2 specs
- Catalytic Converter Flange Bolt40.6 lb-ft55 Nm
- O2 Sensor29.5 lb-ft40 Nm
Catalytic Converter - Universal2 specs
- Catalytic Converter Flange Bolt40.6 lb-ft55 Nm
- O2 Sensor29.5 lb-ft40 Nm
Exhaust Manifold Studs1 spec
- Exhaust Manifold Stud Nut29.5 lb-ft40 Nm
Exhaust Pipe - Rear Section2 specs
- Exhaust Clamp Bolt33.2 lb-ft45 Nm
- Exhaust Flange Bolt36.9 lb-ft50 Nm
Front Pipe2 specs
- Exhaust Clamp Bolt33.2 lb-ft45 Nm
- Exhaust Flange Bolt36.9 lb-ft50 Nm
Muffler2 specs
- Hanger Bracket Bolts18 lb-ft25 Nm
- Muffler Clamps41 lb-ft55 Nm
Resonator2 specs
- Exhaust Clamp Bolt33.2 lb-ft45 Nm
- Exhaust Flange Bolt36.9 lb-ft50 Nm

Heating and A/C

AC Compressor3 specs
- AC Compressor Bolts18 lb-ft25 Nm
- AC Line FittingsUse new O-rings, add PAG oil15 lb-ft20 Nm
- Clutch Connector Bolt6 lb-ft8 Nm
AC Compressor Oil Add2 specs
- AC Compressor Bolts22.1 lb-ft30 Nm
- AC Line Fitting14.8 lb-ft20 Nm
AC Condenser2 specs
- AC Line FittingsUse new O-rings15 lb-ft20 Nm
- Condenser Mounting Bolts9 lb-ft12 Nm

Body

Rear Window1 spec
- Wiper Arm Nut11.1 lb-ft15 Nm
Windshield1 spec
- Wiper Arm Nut11.1 lb-ft15 Nm
Windshield Molding1 spec
- Wiper Arm Nut11.1 lb-ft15 Nm

Torque is shown in lb-ft with Nm below it. Where a step says to turn, tighten the listed angle after the torque step before it. Use new bolts where the note says so.

Need labor times, fluids or repair steps for this car? See it on the Open Labor Project