Building an app? Need this data? Need this data? API access here

2023 Nissan Pathfinder torque specs

3.5L V6 VQ35DE

Change vehicle

Most looked up

Maintenance

  • Tire Rotation2 specs
    • Lug Nuts - Alloy WheelsTorque in star pattern, recheck after 50 miles98 lb-ft133 Nm
    • Lug Nuts - Steel WheelsTorque in star pattern103 lb-ft140 Nm

Brakes

  • Brake Caliper - Front3 specs
    • Bleeder ScrewDo not overtighten7 lb-ft10 Nm
    • Brake Line Banjo BoltUse new copper washers13 lb-ft17 Nm
    • Caliper Bracket BoltsThreadlocker recommended100 lb-ft136 Nm
  • Brake Caliper - Rear3 specs
    • Bleeder ScrewDo not overtighten7 lb-ft10 Nm
    • Brake Line Banjo BoltUse new copper washers13 lb-ft17 Nm
    • Caliper Bracket BoltsThreadlocker recommended63 lb-ft85 Nm
  • Brake Master Cylinder2 specs
    • Brake Line FittingsUse flare nut wrench11 lb-ft15 Nm
    • Master Cylinder Nuts18 lb-ft25 Nm
  • Brake Master Cylinder Rebuild3 specs
    • Brake Line FittingsUse flare nut wrench11 lb-ft15 Nm
    • Master Cylinder Mounting Nuts18 lb-ft25 Nm
    • Reservoir Mounting Bolts6 lb-ft8 Nm
  • Brake Pads - Front3 specs
    • Caliper Bracket BoltsThreadlocker recommended100 lb-ft136 Nm
    • Caliper Slide Pin BoltsApply silicone brake grease26 lb-ft35 Nm
    • Wheel Lug NutsTorque in star pattern98 lb-ft133 Nm
  • Brake Pads - Rear3 specs
    • Caliper Bracket BoltsThreadlocker recommended63 lb-ft85 Nm
    • Caliper Slide Pin BoltsApply silicone brake grease22 lb-ft30 Nm
    • Wheel Lug NutsTorque in star pattern98 lb-ft133 Nm
  • Front Brake Pad Replacement3 specs
    • Caliper Bracket BoltsThreadlocker recommended100 lb-ft136 Nm
    • Caliper Slide Pin BoltsApply silicone brake grease26 lb-ft35 Nm
    • Wheel Lug NutsTorque in star pattern98 lb-ft133 Nm
  • Rear Brake Shoe Replacement3 specs
    • Backing Plate Bolts44 lb-ft60 Nm
    • Wheel Cylinder Bolts9 lb-ft12 Nm
    • Wheel Lug NutsTorque in star pattern98 lb-ft133 Nm

Engine

  • Engine Mount - Front3 specs
    • Engine Mount-to-Block Bolts43 lb-ft58 Nm
    • Engine Mount-to-Frame Bolts46 lb-ft63 Nm
    • Through-Bolt70 lb-ft95 Nm
  • Exhaust Manifold Gasket3 specs
    • Exhaust Manifold NutsApply anti-seize, work hot-to-cold25 lb-ft34 Nm
    • Exhaust Manifold StudsIf replacing studs11 lb-ft15 Nm
    • Heat Shield Bolts7 lb-ft10 Nm
  • Fan Belt Replacement3 specs
    • Idler Pulley Bolt30 lb-ft40 Nm
    • Tensioner Mounting Bolts18 lb-ft25 Nm
    • Tensioner Pulley Bolt33 lb-ft45 Nm
  • Flywheel2 specs
    • Flexplate BoltsAutomatic transmissions63 lb-ft85 Nm
    • Flywheel BoltsOften TTY - check specs, tighten in star pattern70 lb-ft95 Nm
  • Full Engine Tune-Up5 specs
    • Ignition Coil Bolts6 lb-ft8 Nm
    • Spark Plugs - Aluminum HeadApply anti-seize to threads15 lb-ft20 Nm
    • Spark Plugs - Cast Iron HeadApply anti-seize to threads22 lb-ft30 Nm
    • Throttle Body Bolts7 lb-ft10 Nm
    • Valve Cover BoltsTighten in sequence7 lb-ft10 Nm
  • Head Gasket - Single6 specs
    • Exhaust Manifold NutsApply anti-seize18 lb-ft25 Nm
    • Intake Manifold BoltsTighten in sequence18 lb-ft25 Nm
    • Cylinder Head Bolts - Step 1Always use new TTY bolts30 lb-ft40 Nm
    • Cylinder Head Bolts - Step 2Tighten in sequence59 lb-ft80 Nm
    • Cylinder Head Bolts - Step 3Plus 90 degrees29 lb-ft + 90°39 Nm
    • Cylinder Head Bolts - Step 4Plus 90 degreesTurn 90°
  • Intake Manifold Gasket3 specs
    • Fuel Rail Bolts9 lb-ft12 Nm
    • Intake Manifold BoltsTighten in sequence from center out18 lb-ft25 Nm
    • Throttle Body Bolts7 lb-ft10 Nm
  • Oil Change3 specs
    • Oil Drain PlugUse new crush washer26 lb-ft35 Nm
    • Oil Filter (Spin-On)Hand tight plus 3/4 turn15 lb-ft20 Nm
    • Oil Filter Housing CapFor cartridge-type filters18 lb-ft25 Nm
  • Oil Pan Gasket2 specs
    • Oil Drain PlugUse new crush washer26 lb-ft35 Nm
    • Oil Pan BoltsTighten in sequence from center outward9 lb-ft12 Nm
  • Serpentine Belt2 specs
    • Belt Tensioner Bolt41 lb-ft55 Nm
    • Idler Pulley Bolt33 lb-ft45 Nm
  • Throttle Body2 specs
    • Air Intake Hose Clamps2 lb-ft3 Nm
    • Throttle Body Bolts7 lb-ft10 Nm
  • Timing Chain5 specs
    • Camshaft Sprocket Bolts69 lb-ft93 Nm
    • Crankshaft Sprocket BoltOften TTY - check specs32 lb-ft + 90°44 Nm
    • Timing Chain Guide Bolts9 lb-ft12 Nm
    • Timing Chain Tensioner7 lb-ft10 Nm
    • Timing Cover BoltsTighten in sequence9 lb-ft12 Nm
  • Timing Chain Tensioner3 specs
    • Tensioner Cap/PlugUse new crush washer if equipped22 lb-ft30 Nm
    • Tensioner Housing BoltsTighten in sequence7 lb-ft10 Nm
    • Timing Cover Access Bolts9 lb-ft12 Nm
  • Transmission Mount2 specs
    • Crossmember Bolts66 lb-ft90 Nm
    • Transmission Mount Bolts46 lb-ft63 Nm
  • Valve Cover Gasket - Single2 specs
    • Spark Plug Tube SealsIf equipped with separate seals9 lb-ft12 Nm
    • Valve Cover BoltsTighten in sequence7 lb-ft10 Nm

Cooling

  • Coolant Outlet3 specs
    • Coolant Outlet/Housing BoltsTighten in sequence9 lb-ft12 Nm
    • Coolant Temperature Sensor15 lb-ft20 Nm
    • Hose ClampsSpring or constant-tension preferred2 lb-ft3 Nm
  • Radiator4 specs
    • Drain PetcockPlastic - hand tight4 lb-ft5 Nm
    • Radiator Mount BoltsDo not overtighten plastic mounts9 lb-ft12 Nm
    • Transmission Cooler LinesIf equipped18 lb-ft25 Nm
    • Upper/Lower Hose Clamps2 lb-ft3 Nm
  • Radiator Removal and Service4 specs
    • Drain PetcockPlastic - hand-tight only4 lb-ft5 Nm
    • Fan Shroud Bolts7 lb-ft10 Nm
    • Radiator Mount BoltsDo not overtighten plastic mounts9 lb-ft12 Nm
    • Transmission Cooler LinesIf equipped, use new washers18 lb-ft25 Nm
  • Thermostat2 specs
    • Coolant Temperature SensorUse thread sealant15 lb-ft20 Nm
    • Thermostat Housing Bolts11 lb-ft15 Nm
  • Water Pump3 specs
    • Hose ClampsSpring clamps preferred2 lb-ft3 Nm
    • Thermostat Housing Bolts11 lb-ft15 Nm
    • Water Pump BoltsTighten in criss-cross pattern9 lb-ft12 Nm

Ignition

  • Spark Plugs3 specs
    • Ignition Coil Bolts6 lb-ft8 Nm
    • Spark Plugs - Aluminum HeadApply anti-seize to threads15 lb-ft20 Nm
    • Spark Plugs - Cast Iron HeadApply anti-seize to threads22 lb-ft30 Nm

Fuel system

  • Fuel Filter2 specs
    • Fuel Filter Bracket Bolt7 lb-ft10 Nm
    • Fuel Line FittingsIf threaded type18 lb-ft25 Nm
  • Fuel Pump2 specs
    • Fuel Pump Module Lock RingUse special tool22 lb-ft30 Nm
    • Tank Strap Bolts26 lb-ft35 Nm

Electrical

  • Alternator4 specs
    • Alternator Mounting Bolts18 lb-ft25 Nm
    • Alternator Pivot Bolt18 lb-ft25 Nm
    • Battery Terminal BoltsDo not overtighten6 lb-ft8 Nm
    • Serpentine Belt Tensioner41 lb-ft55 Nm
  • Battery3 specs
    • Battery Hold-Down Bolt6 lb-ft8 Nm
    • Battery Terminal BoltsDo not overtighten - can crack terminal4 lb-ft6 Nm
    • Battery Tray Bolts9 lb-ft12 Nm
  • Blower Motor2 specs
    • Blower Motor Resistor Screws1.5 lb-ft2 Nm
    • Blower Motor Screws3 lb-ft4 Nm
  • Starter3 specs
    • Heat Shield BoltsIf equipped7 lb-ft10 Nm
    • Starter Mounting BoltsLong bolt may need extension32 lb-ft44 Nm
    • Starter Solenoid NutFor B+ cable9 lb-ft12 Nm

Suspension

  • Front Suspension Rebuild4 specs
    • Ball Joint Pinch BoltUse new bolt if locknut style37 lb-ft50 Nm
    • Lower Control Arm BoltsTorque at ride height107 lb-ft145 Nm
    • Strut Top Mount Nuts18 lb-ft25 Nm
    • Sway Bar End Link Nuts44 lb-ft60 Nm
  • Rear Suspension Service4 specs
    • Lower Control Arm BoltsTorque at ride height100 lb-ft135 Nm
    • Shock Lower Bolt85 lb-ft115 Nm
    • Sway Bar End Link Nuts37 lb-ft50 Nm
    • Trailing Arm BoltsTorque at ride height103 lb-ft140 Nm
  • Shock Absorber Replacement2 specs
    • Lower Mount Bolt85 lb-ft115 Nm
    • Upper Mount NutUse new self-locking nut41 lb-ft55 Nm
  • Strut Assembly - Front4 specs
    • Strut Mount Center NutHold strut shaft with Allen key53 lb-ft72 Nm
    • Strut Tower NutsDo not loosen center nut unless compressed32 lb-ft43 Nm
    • Strut-to-Knuckle BoltsOften TTY109 lb-ft148 Nm
    • Sway Bar End Link Nuts41 lb-ft55 Nm

Steering

  • Power Steering Pump4 specs
    • Power Steering Pump Bolts18 lb-ft25 Nm
    • Pressure Line FittingUse new O-rings22 lb-ft30 Nm
    • Return Line Clamp3 lb-ft4 Nm
    • Serpentine Belt Tensioner41 lb-ft55 Nm

Drivetrain

  • Driveshaft - Front3 specs
    • Center Support Bearing Bracket Bolts37 lb-ft50 Nm
    • Driveshaft Flange Bolts (CV/U-Joint)Use new bolts if torque-to-yield55 lb-ft75 Nm
    • Transfer Case Output Yoke NutIf accessible133 lb-ft180 Nm
  • Driveshaft - Rear3 specs
    • Differential Pinion Yoke NutUse new nut, set pinion preload183 lb-ft248 Nm
    • Driveshaft Flange Bolts45 lb-ft61 Nm
    • U-Joint Strap BoltsApply threadlocker26 lb-ft35 Nm
  • Driveshaft Center Support Bearing2 specs
    • Center Support Bearing Bracket Bolts37 lb-ft50 Nm
    • Driveshaft Flange Bolts45 lb-ft61 Nm
  • Wheel Bearing Hub - Front4 specs
    • ABS Sensor BoltDo not overtighten7 lb-ft10 Nm
    • Axle NutUse new cotter pin after torque184 lb-ft250 Nm
    • Brake Caliper Bracket Bolts88 lb-ft120 Nm
    • Wheel Bearing Hub BoltsApply threadlocker if specified79 lb-ft107 Nm
  • Wheel Bearing Hub - Rear3 specs
    • Axle NutUse new cotter pin after torque148 lb-ft200 Nm
    • Brake Caliper Bracket Bolts81 lb-ft110 Nm
    • Wheel Bearing Hub BoltsApply threadlocker if specified69 lb-ft94 Nm

Exhaust

  • Muffler2 specs
    • Hanger Bracket Bolts18 lb-ft25 Nm
    • Muffler Clamps41 lb-ft55 Nm

Heating and A/C

  • AC Compressor3 specs
    • AC Compressor Mounting Bolts18 lb-ft25 Nm
    • AC Line FittingsUse new O-rings, add PAG oil7 lb-ft10 Nm
    • Clutch Connector Bolt6 lb-ft8 Nm
  • AC Condenser2 specs
    • AC Line FittingsUse new O-rings7 lb-ft10 Nm
    • Condenser Mounting Bolts9 lb-ft12 Nm

Torque is shown in lb-ft with Nm below it. Where a step says to turn, tighten the listed angle after the torque step before it. Use new bolts where the note says so.

Need labor times, fluids or repair steps for this car? See it on the Open Labor Project