2019 Mercedes-Benz G550 W463 torque specs

4.0L V8 BiTurbo M176

Change vehicle

Most looked up

Lug nuts133 lb-ft180 Nm
Oil drain plug26 lb-ft35 Nm
Spark plugs18 lb-ft24 Nm
Front caliper bracket bolts88 lb-ft120 Nm
Rear caliper bracket bolts74 lb-ft100 Nm
Front axle nut184 lb-ft250 Nm
Outer tie rod end nut59 lb-ft80 Nm

Maintenance

AC System Diagnosis2 specs
- AC Line FittingsNew O-rings17 lb-ft23 Nm
- Connector Bolts6 lb-ft8 Nm
Air Filter4 specs
- Air Box Clips4 lb-ft5 Nm
- Intake Tube Clamp3 lb-ft4 Nm
- MAF Sensor Screws3 lb-ft5 Nm
- Mass Air Flow Sensor Screws2 lb-ft3 Nm
Battery Test5 specs
- Battery Hold-Down BoltDo not overtighten9 lb-ft12 Nm
- Battery Terminal BoltsClean terminals6 lb-ft8 Nm
- Connector Bolts6 lb-ft8 Nm
- Ground Cable Bolt12 lb-ft16 Nm
- Oil Drain PlugUse new crush washer26 lb-ft35 Nm
Charging System Test2 specs
- Connector Bolts6 lb-ft8 Nm
- Oil Drain PlugUse new crush washer26 lb-ft35 Nm
Check Engine Light Diagnosis2 specs
- Connector Bolts6 lb-ft8 Nm
- Oil Drain PlugUse new crush washer26 lb-ft35 Nm
Compression Test3 specs
- Air Box Clips4 lb-ft5 Nm
- Connector Bolts6 lb-ft8 Nm
- Oil Drain PlugUse new crush washer26 lb-ft35 Nm
Cooling System Pressure Test2 specs
- Connector Bolts6 lb-ft8 Nm
- Oil Drain PlugUse new crush washer26 lb-ft35 Nm
Diagnostic Scan1 spec
- Connector Bolts6 lb-ft8 Nm
Differential Service4 specs
- Connector Bolts6 lb-ft8 Nm
- Drain PlugNew washer35 lb-ft47 Nm
- Fill Plug35 lb-ft47 Nm
- Oil Drain PlugUse new crush washer26 lb-ft35 Nm
Drivability Diagnosis2 specs
- Air Box Clips4 lb-ft5 Nm
- Connector Bolts6 lb-ft8 Nm
Electrical Diagnosis1 spec
- Connector Bolts6 lb-ft8 Nm
Fluid Leak Diagnosis2 specs
- Connector Bolts6 lb-ft8 Nm
- Oil Drain PlugUse new crush washer26 lb-ft35 Nm
Leak-Down Test2 specs
- Air Box Clips4 lb-ft5 Nm
- Connector Bolts6 lb-ft8 Nm
Noise Diagnosis3 specs
- Connector Bolts6 lb-ft8 Nm
- Oil Drain PlugUse new crush washer26 lb-ft35 Nm
- Wheel Lug NutsTorque in star pattern133 lb-ft180 Nm
Power Steering Service4 specs
- Air Box ClipsVerify sequence with the service manual4 lb-ft5 Nm
- Connector Bolts6 lb-ft8 Nm
- Pressure Line FittingNew O-ring29 lb-ft39 Nm
- Pump Mounting Bolts15 lb-ft20 Nm
Tire Balance2 specs
- Connector Bolts6 lb-ft8 Nm
- Wheel Lug NutsTorque in star pattern133 lb-ft180 Nm
Tire Mount and Balance2 specs
- Connector Bolts6 lb-ft8 Nm
- Wheel Lug NutsTorque in star pattern133 lb-ft180 Nm
Tire Rotation2 specs
- Lug Nuts - Alloy WheelsTorque in star pattern, recheck after 50 miles133 lb-ft180 Nm
- Lug Nuts - Steel WheelsTorque in star pattern133 lb-ft180 Nm
TPMS Relearn2 specs
- Connector Bolts6 lb-ft8 Nm
- Oil Drain PlugUse new crush washer26 lb-ft35 Nm
TPMS Sensor3 specs
- Connector Bolts6 lb-ft8 Nm
- Oil Drain PlugUse new crush washer26 lb-ft35 Nm
- Wheel Lug NutsTorque in star pattern133 lb-ft180 Nm
Transmission Service2 specs
- Connector Bolts6 lb-ft8 Nm
- Oil Drain PlugUse new crush washer15 lb-ft20 Nm
Tune-Up - Major3 specs
- Air Box Clips4 lb-ft5 Nm
- Connector Bolts6 lb-ft8 Nm
- Oil Drain PlugUse new crush washer26 lb-ft35 Nm
Tune-Up - Minor3 specs
- Air Box Clips4 lb-ft5 Nm
- Connector Bolts6 lb-ft8 Nm
- Oil Drain PlugUse new crush washer26 lb-ft35 Nm
Wheel Alignment9 specs
- Air Box Clips4 lb-ft5 Nm
- Cam BoltsAfter adjustment95 lb-ft129 Nm
- Camber BoltsIf adjustable55 lb-ft75 Nm
- Connector Bolts6 lb-ft8 Nm
- Oil Drain PlugUse new crush washer26 lb-ft35 Nm
- Subframe BoltsIf adjusted98 lb-ft133 Nm
- Tie Rod Jam Nuts30 lb-ft40 Nm
- Tie Rod Lock NutAfter adjustment50 lb-ft68 Nm
- Wheel Lug NutsTorque in star pattern133 lb-ft180 Nm

Brakes

ABS Module5 specs
- ABS Module Bolts7 lb-ft10 Nm
- Bleeder Screw12 lb-ft16 Nm
- Brake Line FittingsUse flare nut wrench11 lb-ft15 Nm
- Caliper Mounting BoltsUse thread locker75 lb-ft102 Nm
- Wheel Lug NutsTorque in star pattern133 lb-ft180 Nm
ABS Pump4 specs
- Bleeder ScrewDo not overtighten7 lb-ft10 Nm
- Caliper Bracket Bolts - FrontThreadlocker recommended133 lb-ft180 Nm
- Caliper Mounting BoltsUse thread locker75 lb-ft102 Nm
- Wheel Lug NutsTorque in star pattern133 lb-ft180 Nm
ABS Tone Ring4 specs
- Caliper Bracket Bolts - FrontThreadlocker recommended133 lb-ft180 Nm
- Caliper Mounting BoltsUse thread locker75 lb-ft102 Nm
- Caliper Slide Pin BoltsApply silicone brake grease26 lb-ft35 Nm
- Wheel Lug NutsTorque in star pattern133 lb-ft180 Nm
ABS Wheel Speed Sensor - Front5 specs
- ABS Sensor BoltDo not overtighten7 lb-ft10 Nm
- Bleeder Screw12 lb-ft16 Nm
- Caliper Mounting BoltsUse thread locker75 lb-ft102 Nm
- Wheel Bearing Hub Bolts65 lb-ft88 Nm
- Wheel Lug NutsTorque in star pattern133 lb-ft180 Nm
ABS Wheel Speed Sensor - Rear4 specs
- ABS Sensor BoltDo not overtighten7 lb-ft10 Nm
- Bleeder Screw12 lb-ft16 Nm
- Caliper Mounting BoltsUse thread locker75 lb-ft102 Nm
- Wheel Lug NutsTorque in star pattern133 lb-ft180 Nm
Brake Bleed - All Four5 specs
- Bleeder ScrewDo not overtighten. Verify sequence with the service manual7 lb-ft10 Nm
- Caliper Bracket Bolts - FrontThreadlocker recommended. Verify sequence with the service manual88 lb-ft120 Nm
- Caliper Mounting BoltsUse thread locker75 lb-ft102 Nm
- Caliper Slide Pin BoltsApply silicone brake grease. Verify sequence with the service manual26 lb-ft35 Nm
- Wheel Lug NutsTorque in star pattern. Verify sequence with the service manual133 lb-ft180 Nm
Brake Booster6 specs
- Bleeder Screw12 lb-ft16 Nm
- Brake Booster NutsVerify sequence with the service manual15 lb-ft20 Nm
- Brake Pedal Pushrod LockVerify sequence with the service manual7 lb-ft9 Nm
- Caliper Mounting BoltsUse thread locker75 lb-ft102 Nm
- Master Cylinder NutsVerify sequence with the service manual18 lb-ft25 Nm
- Wheel Lug NutsTorque in star pattern133 lb-ft180 Nm
Brake Booster Check Valve3 specs
- Caliper Bracket Bolts - FrontThreadlocker recommended. Verify sequence with the service manual88 lb-ft120 Nm
- Caliper Mounting BoltsUse thread locker75 lb-ft102 Nm
- Caliper Slide Pin BoltsApply silicone brake grease. Verify sequence with the service manual26 lb-ft35 Nm
Brake Caliper - Front3 specs
- Bleeder ScrewDo not overtighten7 lb-ft10 Nm
- Brake Line Banjo BoltUse new copper washers30 lb-ft40 Nm
- Caliper Bracket BoltsThreadlocker recommended88 lb-ft120 Nm
Brake Caliper - Rear3 specs
- Bleeder ScrewDo not overtighten7 lb-ft10 Nm
- Brake Line Banjo BoltUse new copper washers30 lb-ft40 Nm
- Caliper Bracket BoltsThreadlocker recommended74 lb-ft100 Nm
Brake Caliper Bracket6 specs
- Bleeder ScrewDo not overtighten. Verify sequence with the service manual7 lb-ft10 Nm
- Brake Hose Banjo BoltNew copper washers35 lb-ft47 Nm
- Caliper Bracket Bolts - FrontThreadlocker recommended. Verify sequence with the service manual88 lb-ft120 Nm
- Caliper Mounting BoltsUse thread locker75 lb-ft102 Nm
- Caliper Slide Pin BoltsApply silicone brake grease. Verify sequence with the service manual26 lb-ft35 Nm
- Wheel Lug NutsTorque in star pattern. Verify sequence with the service manual133 lb-ft180 Nm
Brake Caliper Rebuild - Front5 specs
- Bleeder ScrewDo not overtighten7 lb-ft10 Nm
- Caliper Bracket Bolts - FrontThreadlocker recommended88 lb-ft120 Nm
- Caliper Mounting BoltsUse thread locker75 lb-ft102 Nm
- Caliper Slide Pin BoltsApply silicone brake grease26 lb-ft35 Nm
- Wheel Lug NutsTorque in star pattern133 lb-ft180 Nm
Brake Caliper Rebuild - Rear4 specs
- Bleeder ScrewDo not overtighten7 lb-ft10 Nm
- Caliper Mounting BoltsUse thread locker22 lb-ft30 Nm
- Caliper Slide Pin BoltsApply silicone brake grease26 lb-ft35 Nm
- Wheel Lug NutsTorque in star pattern133 lb-ft180 Nm
Brake Caliper Slide Pins4 specs
- Caliper Bracket Bolts - FrontThreadlocker recommended88 lb-ft120 Nm
- Caliper Mounting BoltsUse thread locker22 lb-ft30 Nm
- Caliper Slide Pin BoltsApply silicone brake grease26 lb-ft35 Nm
- Wheel Lug NutsTorque in star pattern133 lb-ft180 Nm
Brake Fluid Flush8 specs
- Air Box ClipsVerify sequence with the service manual4 lb-ft5 Nm
- Bleeder ScrewDo not overtighten. Verify sequence with the service manual7 lb-ft10 Nm
- Caliper Bracket Bolts - FrontThreadlocker recommended. Verify sequence with the service manual88 lb-ft120 Nm
- Caliper Mounting Bolts75 lb-ft102 Nm
- Caliper Slide Pin BoltsApply silicone brake grease. Verify sequence with the service manual26 lb-ft35 Nm
- Connector Bolts6 lb-ft8 Nm
- Master Cylinder CapHand tight3 lb-ft4 Nm
- Wheel Lug NutsTorque in star pattern. Verify sequence with the service manual133 lb-ft180 Nm
Brake Hose - Front5 specs
- Bleeder Screw12 lb-ft16 Nm
- Brake Hose Banjo BoltUse new copper washers. Verify sequence with the service manual30 lb-ft40 Nm
- Brake Hose BracketVerify sequence with the service manual7 lb-ft10 Nm
- Caliper Mounting BoltsUse thread locker75 lb-ft102 Nm
- Wheel Lug NutsTorque in star pattern133 lb-ft180 Nm
Brake Hose - Rear5 specs
- Bleeder Screw12 lb-ft16 Nm
- Brake Hose Banjo BoltUse new copper washers. Verify sequence with the service manual30 lb-ft40 Nm
- Brake Hose BracketVerify sequence with the service manual7 lb-ft10 Nm
- Caliper Mounting BoltsUse thread locker75 lb-ft102 Nm
- Wheel Lug NutsTorque in star pattern133 lb-ft180 Nm
Brake Light Switch4 specs
- Bleeder ScrewDo not overtighten. Verify sequence with the service manual10 lb-ft14 Nm
- Caliper Bracket Bolts - FrontThreadlocker recommended. Verify sequence with the service manual88 lb-ft120 Nm
- Caliper Mounting BoltsUse thread locker75 lb-ft102 Nm
- Caliper Slide Pin BoltsApply silicone brake grease. Verify sequence with the service manual26 lb-ft35 Nm
Brake Line - Single5 specs
- Bleeder ScrewDo not overtighten. Verify sequence with the service manual10 lb-ft14 Nm
- Caliper Bracket Bolts - FrontThreadlocker recommended. Verify sequence with the service manual88 lb-ft120 Nm
- Caliper Mounting BoltsUse thread locker75 lb-ft102 Nm
- Caliper Slide Pin BoltsApply silicone brake grease. Verify sequence with the service manual26 lb-ft35 Nm
- Wheel Lug NutsTorque in star pattern. Verify sequence with the service manual133 lb-ft180 Nm
Brake Lines - Complete Set5 specs
- Bleeder ScrewDo not overtighten. Verify sequence with the service manual10 lb-ft14 Nm
- Caliper Bracket Bolts - FrontThreadlocker recommended. Verify sequence with the service manual88 lb-ft120 Nm
- Caliper Mounting BoltsUse thread locker75 lb-ft102 Nm
- Caliper Slide Pin BoltsApply silicone brake grease. Verify sequence with the service manual26 lb-ft35 Nm
- Wheel Lug NutsTorque in star pattern. Verify sequence with the service manual133 lb-ft180 Nm
Brake Master Cylinder2 specs
- Brake Line FittingsUse flare nut wrench11 lb-ft15 Nm
- Master Cylinder Nuts18 lb-ft25 Nm
Brake Master Cylinder Rebuild3 specs
- Brake Line FittingsUse flare nut wrench11 lb-ft15 Nm
- Master Cylinder Mounting Nuts18 lb-ft25 Nm
- Reservoir Mounting Bolts6 lb-ft8 Nm
Brake Pads - Front3 specs
- Caliper Bracket BoltsThreadlocker recommended88 lb-ft120 Nm
- Caliper Slide Pin BoltsApply silicone brake grease26 lb-ft35 Nm
- Wheel Lug NutsTorque in star pattern133 lb-ft180 Nm
Brake Pads - Rear3 specs
- Caliper Bracket BoltsThreadlocker recommended74 lb-ft100 Nm
- Caliper Slide Pin BoltsApply silicone brake grease22 lb-ft30 Nm
- Wheel Lug NutsTorque in star pattern133 lb-ft180 Nm
Brake Pads and Rotors - Front7 specs
- Bleeder ScrewDo not overtighten. Verify sequence with the service manual10 lb-ft14 Nm
- Caliper Bracket BoltsUse thread locker86 lb-ft117 Nm
- Caliper Bracket Bolts - FrontThreadlocker recommended. Verify sequence with the service manual88 lb-ft120 Nm
- Caliper Mounting BoltsUse thread locker75 lb-ft102 Nm
- Caliper Slide BoltsLubricate pins29 lb-ft39 Nm
- Caliper Slide Pin BoltsApply silicone brake grease. Verify sequence with the service manual26 lb-ft35 Nm
- Wheel Lug NutsTorque in star pattern. Verify sequence with the service manual133 lb-ft180 Nm
Brake Pads and Rotors - Rear7 specs
- Bleeder ScrewDo not overtighten. Verify sequence with the service manual10 lb-ft14 Nm
- Caliper Bracket BoltsUse thread locker86 lb-ft117 Nm
- Caliper Bracket Bolts - FrontThreadlocker recommended. Verify sequence with the service manual88 lb-ft120 Nm
- Caliper Mounting BoltsUse thread locker75 lb-ft102 Nm
- Caliper Slide BoltsLubricate pins29 lb-ft39 Nm
- Caliper Slide Pin BoltsApply silicone brake grease. Verify sequence with the service manual26 lb-ft35 Nm
- Wheel Lug NutsTorque in star pattern. Verify sequence with the service manual133 lb-ft180 Nm
Brake Proportioning Valve5 specs
- Bleeder Screw12 lb-ft16 Nm
- Brake Line FittingsUse flare nut wrench. Verify sequence with the service manual11 lb-ft15 Nm
- Caliper Mounting BoltsUse thread locker75 lb-ft102 Nm
- Proportioning Valve BoltsVerify sequence with the service manual11 lb-ft15 Nm
- Wheel Lug NutsTorque in star pattern133 lb-ft180 Nm
Brake Rotor - Front Single8 specs
- Bleeder ScrewDo not overtighten. Verify sequence with the service manual10 lb-ft14 Nm
- Brake Rotor Set Screw6 lb-ft8 Nm
- Caliper Bracket Bolts86 lb-ft117 Nm
- Caliper Bracket Bolts - FrontThreadlocker recommended. Verify sequence with the service manual88 lb-ft120 Nm
- Caliper Mounting BoltsUse thread locker75 lb-ft102 Nm
- Caliper Slide Pin BoltsApply silicone brake grease. Verify sequence with the service manual26 lb-ft35 Nm
- Hub NutIf removed207 lb-ft281 Nm
- Wheel Lug NutsTorque in star pattern. Verify sequence with the service manual133 lb-ft180 Nm
Brake Rotor - Rear Single7 specs
- Bleeder ScrewDo not overtighten. Verify sequence with the service manual7 lb-ft10 Nm
- Brake Rotor Set Screw6 lb-ft8 Nm
- Caliper Bracket Bolts86 lb-ft117 Nm
- Caliper Mounting BoltsUse thread locker22 lb-ft30 Nm
- Caliper Slide Pin BoltsApply silicone brake grease. Verify sequence with the service manual26 lb-ft35 Nm
- Hub NutIf removed207 lb-ft281 Nm
- Wheel Lug NutsTorque in star pattern. Verify sequence with the service manual133 lb-ft180 Nm
Brake Rotors - Front Pair8 specs
- Bleeder ScrewDo not overtighten. Verify sequence with the service manual7 lb-ft10 Nm
- Brake Rotor Set Screw6 lb-ft8 Nm
- Caliper Bracket Bolts86 lb-ft117 Nm
- Caliper Bracket Bolts - FrontThreadlocker recommended. Verify sequence with the service manual88 lb-ft120 Nm
- Caliper Mounting BoltsUse thread locker75 lb-ft102 Nm
- Caliper Slide Pin BoltsApply silicone brake grease. Verify sequence with the service manual26 lb-ft35 Nm
- Hub NutIf removed207 lb-ft281 Nm
- Wheel Lug NutsTorque in star pattern. Verify sequence with the service manual133 lb-ft180 Nm
Brake Rotors - Rear Pair7 specs
- Bleeder ScrewDo not overtighten. Verify sequence with the service manual7 lb-ft10 Nm
- Brake Rotor Set Screw6 lb-ft8 Nm
- Caliper Bracket Bolts86 lb-ft117 Nm
- Caliper Mounting BoltsUse thread locker22 lb-ft30 Nm
- Caliper Slide Pin BoltsApply silicone brake grease. Verify sequence with the service manual26 lb-ft35 Nm
- Hub NutIf removed207 lb-ft281 Nm
- Wheel Lug NutsTorque in star pattern. Verify sequence with the service manual133 lb-ft180 Nm
Electronic Parking Brake Motor5 specs
- Bleeder ScrewDo not overtighten. Verify sequence with the service manual7 lb-ft10 Nm
- Caliper Bracket Bolts - FrontThreadlocker recommended. Verify sequence with the service manual88 lb-ft120 Nm
- Caliper Mounting BoltsUse thread locker28 lb-ft38 Nm
- Caliper Slide Pin BoltsApply silicone brake grease. Verify sequence with the service manual26 lb-ft35 Nm
- Wheel Lug NutsTorque in star pattern. Verify sequence with the service manual133 lb-ft180 Nm
Front Brake Pad Replacement3 specs
- Caliper Bracket BoltsThreadlocker recommended88 lb-ft120 Nm
- Caliper Slide Pin BoltsApply silicone brake grease26 lb-ft35 Nm
- Wheel Lug NutsTorque in star pattern133 lb-ft180 Nm
Parking Brake Actuator3 specs
- Caliper Mounting BoltsUse thread locker75 lb-ft102 Nm
- Caliper Slide Pin BoltsApply silicone brake grease. Verify sequence with the service manual26 lb-ft35 Nm
- Wheel Lug NutsTorque in star pattern. Verify sequence with the service manual133 lb-ft180 Nm
Parking Brake Cable5 specs
- Bleeder Screw12 lb-ft16 Nm
- Cable Bracket BoltsVerify sequence with the service manual9 lb-ft12 Nm
- Caliper Mounting BoltsUse thread locker75 lb-ft102 Nm
- Equalizer NutAdjust for proper tension. Verify sequence with the service manual11 lb-ft15 Nm
- Wheel Lug NutsTorque in star pattern133 lb-ft180 Nm
Parking Brake Shoes5 specs
- Adjuster LockVerify sequence with the service manual4 lb-ft5 Nm
- Bleeder Screw12 lb-ft16 Nm
- Caliper Mounting BoltsUse thread locker75 lb-ft102 Nm
- Hold-Down SpringsVerify sequence with the service manual6 lb-ft8 Nm
- Wheel Lug NutsTorque in star pattern. Verify sequence with the service manual133 lb-ft180 Nm

Engine

Boost Pressure Sensor4 specs
- Boost Sensor11 lb-ft15 Nm
- Electrical Connector Bolts6 lb-ft8 Nm
- Gasket Surface BoltsClean mating surfaces7 lb-ft9 Nm
- Sensor Mounting Bolts9 lb-ft12 Nm
Camshaft Position Sensor5 specs
- Camshaft Position Sensor7 lb-ft10 Nm
- Electrical Connector Bolts6 lb-ft8 Nm
- Gasket Surface BoltsClean mating surfaces7 lb-ft9 Nm
- Sensor Mounting Bolts9 lb-ft12 Nm
- Valve Cover BoltsTighten in sequence7 lb-ft10 Nm
Camshaft R&R20 specs
- Cam Phaser BoltApply threadlocker, hold cam stationary30 lb-ft40 Nm
- Camshaft Bearing Cap BoltsTighten in sequence, 3 passes10 lb-ft14 Nm
- Camshaft Cap BoltsTighten in sequence from center outward, multiple passes10 lb-ft14 Nm
- Camshaft Position Sensor7 lb-ft10 Nm
- Camshaft Sprocket BoltsHold cam with wrench on hex30 lb-ft40 Nm
- Crankshaft Position Sensor7 lb-ft10 Nm
- Crankshaft Pulley BoltOften TTY, may need impact133 lb-ft180 Nm
- Electrical Connector Bolts6 lb-ft8 Nm
- Gasket Surface BoltsClean mating surfaces7 lb-ft10 Nm
- Oil Drain PlugUse new crush washer26 lb-ft35 Nm
- Rocker Arm BoltsTighten with cam lobe pointing away22 lb-ft30 Nm
- Rocker Arm Shaft BoltsTighten evenly in sequence18 lb-ft25 Nm
- Sensor Mounting Bolts9 lb-ft12 Nm
- Timing Chain Guide BoltsReplace if worn15 lb-ft20 Nm
- Timing Chain Idler Sprocket22 lb-ft30 Nm
- Timing Chain Tensioner BoltInstall with pin/clip to compress18 lb-ft25 Nm
- Timing Cover Bolts - 10mmTighten in sequence33 lb-ft45 Nm
- Timing Cover Bolts - 8mmTighten in sequence18 lb-ft25 Nm
- Valve Cover BoltsTighten in sequence7 lb-ft10 Nm
- VVT Solenoid Bolt7 lb-ft10 Nm
Connecting Rod Bearings6 specs
- Connecting Rod BoltsAMG rod bolts are TTY. REPLACE EVERY TIME. Step 1: 22 lb-ft. Step 2: +90°18 lb-ft + 90°25 Nm
- Electrical Connector Bolts6 lb-ft8 Nm
- Gasket Surface BoltsClean mating surfaces7 lb-ft10 Nm
- Oil Drain PlugUse new crush washer26 lb-ft35 Nm
- Oil Pan BoltTighten in sequence9 lb-ft12 Nm
- Sensor Mounting Bolts9 lb-ft12 Nm
Crankshaft Position Sensor4 specs
- Crankshaft Position Sensor7 lb-ft10 Nm
- Electrical Connector Bolts6 lb-ft8 Nm
- Gasket Surface BoltsClean mating surfaces17 lb-ft23 Nm
- Sensor Mounting Bolts9 lb-ft12 Nm
Crankshaft R&R20 specs
- Connecting Rod BoltsTTY - critical torque plus angle33 lb-ft45 Nm
- Crankshaft Pulley BoltOften TTY, may need impact133 lb-ft180 Nm
- Cylinder Head BoltsTTY - tighten in sequence plus angle30 lb-ft40 Nm
- Electrical Connector Bolts6 lb-ft8 Nm
- Flexplate BoltsAutomatic transmissions33 lb-ft45 Nm
- Flywheel BoltsOften TTY, tighten in star pattern70 lb-ft95 Nm
- Front Main Seal Housing9 lb-ft12 Nm
- Gasket Surface BoltsClean mating surfaces17 lb-ft23 Nm
- Main Bearing Cap BoltsTTY - tighten in sequence plus angle55 lb-ft75 Nm
- Oil Drain PlugUse new crush washer26 lb-ft35 Nm
- Oil Pan BoltTighten in sequence15 lb-ft20 Nm
- Oil Pump Bolts15 lb-ft20 Nm
- Oil Pump Pickup Tube9 lb-ft12 Nm
- Rear Main Seal Housing9 lb-ft12 Nm
- Sensor Mounting Bolts9 lb-ft12 Nm
- Timing Chain Guide BoltsReplace if worn9 lb-ft12 Nm
- Timing Chain Tensioner BoltInstall with pin/clip to compress30 lb-ft40 Nm
- Timing Cover Bolts - 10mmTighten in sequence33 lb-ft45 Nm
- Timing Cover Bolts - 8mmTighten in sequence18 lb-ft25 Nm
- Transmission-to-Engine Bolts33 lb-ft45 Nm
Cylinder Head R&R18 specs
- Camshaft Bearing Cap BoltsTighten in sequence, 3 passes10 lb-ft14 Nm
- Camshaft Bearing CapsTighten in sequence. AMG cams require precise alignment8 lb-ft11 Nm
- Camshaft Cap BoltsTighten in sequence from center outward, multiple passes10 lb-ft14 Nm
- Camshaft Sprocket BoltsHold cam with wrench on hex59 lb-ft80 Nm
- Cylinder Head BoltsREPLACE BOLTS. AMG spec: Step 1: 26 lb-ft. Step 2: +90°. Step 3: +90°. Critical for high-boost applications26 lb-ft + 90°35 Nm
- Electrical Connector Bolts6 lb-ft8 Nm
- Exhaust Manifold NutsApply anti-seize, work hot-to-cold22 lb-ft30 Nm
- Gasket Surface BoltsClean mating surfaces17 lb-ft23 Nm
- Intake Manifold Bolt7 lb-ft9 Nm
- Oil Drain PlugUse new crush washer26 lb-ft35 Nm
- Rocker Arm BoltsTighten with cam lobe pointing away22 lb-ft30 Nm
- Rocker Arm Shaft BoltsTighten evenly in sequence18 lb-ft25 Nm
- Sensor Mounting Bolts9 lb-ft12 Nm
- Thermostat Housing Bolt11 lb-ft15 Nm
- Timing Chain Guide BoltsReplace if worn9 lb-ft12 Nm
- Timing Chain Tensioner BoltInstall with pin/clip to compress30 lb-ft40 Nm
- Timing Cover Bolts - 8mmTighten in sequence15 lb-ft20 Nm
- Valve Cover BoltsTighten in sequence7 lb-ft10 Nm
Cylinder Head Resurface7 specs
- Cylinder Head BoltsTTY - tighten in sequence plus angle22 lb-ft30 Nm
- Electrical Connector Bolts6 lb-ft8 Nm
- Exhaust Manifold NutsApply anti-seize, work hot-to-cold22 lb-ft30 Nm
- Gasket Surface BoltsClean mating surfaces17 lb-ft23 Nm
- Intake Manifold Bolt7 lb-ft10 Nm
- Sensor Mounting Bolts9 lb-ft12 Nm
- Valve Cover BoltsTighten in sequence7 lb-ft10 Nm
Engine Mount - Front3 specs
- Engine Mount Through-Bolt63 lb-ft85 Nm
- Engine Mount-to-Block Bolts48 lb-ft65 Nm
- Engine Mount-to-Frame Bolts55 lb-ft75 Nm
Engine Mount - Rear6 specs
- Electrical Connector Bolts6 lb-ft8 Nm
- Engine Mount Through-Bolt75 lb-ft101 Nm
- Engine Mount-to-Block Bolts32 lb-ft43 Nm
- Engine Mount-to-Frame Bolts30 lb-ft40 Nm
- Gasket Surface BoltsClean mating surfaces17 lb-ft23 Nm
- Sensor Mounting Bolts9 lb-ft12 Nm
Engine Mounts - All7 specs
- Electrical Connector Bolts6 lb-ft8 Nm
- Engine Mount Through-Bolt63 lb-ft85 Nm
- Engine Mount-to-Block Bolts35 lb-ft48 Nm
- Engine Mount-to-Frame Bolts32 lb-ft43 Nm
- Gasket Surface BoltsClean mating surfaces17 lb-ft23 Nm
- Sensor Mounting Bolts9 lb-ft12 Nm
- Transmission Mount Bolts30 lb-ft40 Nm
Engine R&R13 specs
- AC Compressor Bolts15 lb-ft20 Nm
- Alternator Mounting Bolts15 lb-ft20 Nm
- Electrical Connector Bolts6 lb-ft8 Nm
- Engine Mount-to-Block Bolts35 lb-ft48 Nm
- Engine Mount-to-Frame Bolts32 lb-ft43 Nm
- Exhaust Manifold NutsApply anti-seize, work hot-to-cold18 lb-ft25 Nm
- Flywheel BoltsOften TTY, tighten in star pattern33 lb-ft45 Nm
- Gasket Surface BoltsClean mating surfaces17 lb-ft23 Nm
- Oil Drain PlugUse new crush washer26 lb-ft35 Nm
- Power Steering Pump Bolts15 lb-ft20 Nm
- Sensor Mounting Bolts9 lb-ft12 Nm
- Starter Mounting Bolt37 lb-ft50 Nm
- Transmission-to-Engine Bolts33 lb-ft45 Nm
Engine Rebuild21 specs
- Balance Shaft Bolts18 lb-ft25 Nm
- Camshaft Bearing Cap BoltsTighten in sequence, 3 passes10 lb-ft14 Nm
- Camshaft Cap BoltsTighten in sequence from center outward, multiple passes10 lb-ft14 Nm
- Connecting Rod BoltsTTY - critical torque plus angle22 lb-ft30 Nm
- Crankshaft Pulley BoltOften TTY - check spec, may require impact133 lb-ft180 Nm
- Cylinder Head BoltsTTY - tighten in sequence plus angle48 lb-ft65 Nm
- Electrical Connector Bolts6 lb-ft8 Nm
- Exhaust Manifold NutsApply anti-seize, work hot-to-cold18 lb-ft25 Nm
- Flywheel BoltsOften TTY, tighten in star pattern33 lb-ft45 Nm
- Gasket Surface BoltsClean mating surfaces17 lb-ft23 Nm
- Intake Manifold Bolt7 lb-ft10 Nm
- Main Bearing Cap BoltsTTY - tighten in sequence plus angle55 lb-ft75 Nm
- Oil Drain PlugUse new crush washer26 lb-ft35 Nm
- Oil Pan BoltTighten in sequence9 lb-ft12 Nm
- Oil Pump Bolts15 lb-ft20 Nm
- Oil Pump Pickup Tube9 lb-ft12 Nm
- Sensor Mounting Bolts9 lb-ft12 Nm
- Timing Chain Guide BoltsReplace if worn9 lb-ft12 Nm
- Timing Chain Tensioner BoltInstall with pin/clip to compress32 lb-ft43 Nm
- Timing Cover Bolts - 8mmTighten in sequence15 lb-ft20 Nm
- Valve Cover BoltsTighten in sequence7 lb-ft10 Nm
Exhaust Manifold8 specs
- Electrical Connector Bolts6 lb-ft8 Nm
- Exhaust Flange BoltApply anti-seize. Verify sequence with the service manual18 lb-ft25 Nm
- Exhaust Manifold NutsM177 integrated manifold/turbo design. Use new gaskets22 lb-ft30 Nm
- Gasket Surface BoltsClean mating surfaces17 lb-ft23 Nm
- Hanger Bolts17 lb-ft23 Nm
- Heat Shield BoltsVerify sequence with the service manual7 lb-ft10 Nm
- O2 SensorAnti-seize threads33 lb-ft45 Nm
- Sensor Mounting Bolts9 lb-ft12 Nm
Exhaust Manifold Gasket3 specs
- Exhaust Manifold NutsApply anti-seize, work hot-to-cold22 lb-ft30 Nm
- Exhaust Manifold StudsIf replacing studs11 lb-ft15 Nm
- Heat Shield Bolts7 lb-ft10 Nm
Fan Belt Replacement3 specs
- Idler Pulley Bolt30 lb-ft40 Nm
- Tensioner Bolt18 lb-ft25 Nm
- Tensioner Pulley Bolt33 lb-ft45 Nm
Flexplate6 specs
- Electrical Connector Bolts6 lb-ft8 Nm
- Flexplate BoltsAutomatic transmissions. Verify sequence with the service manual33 lb-ft45 Nm
- Gasket Surface BoltsClean mating surfaces17 lb-ft23 Nm
- Sensor Mounting Bolts9 lb-ft12 Nm
- Torque Converter BoltsVerify sequence with the service manual31 lb-ft42 Nm
- Transmission-to-Engine BoltsVerify sequence with the service manual33 lb-ft45 Nm
Freeze Plug - Single4 specs
- Electrical Connector Bolts6 lb-ft8 Nm
- Freeze PlugUse sealant on edges7 lb-ft10 Nm
- Gasket Surface BoltsClean mating surfaces17 lb-ft23 Nm
- Sensor Mounting Bolts9 lb-ft12 Nm
Freeze Plugs - All4 specs
- Electrical Connector Bolts6 lb-ft8 Nm
- Freeze PlugUse sealant on edges7 lb-ft10 Nm
- Gasket Surface BoltsClean mating surfaces17 lb-ft23 Nm
- Sensor Mounting Bolts9 lb-ft12 Nm
Front Main Seal8 specs
- Crankshaft Pulley BoltOften TTY, may need impact133 lb-ft180 Nm
- Electrical Connector Bolts6 lb-ft8 Nm
- Gasket Surface BoltsClean mating surfaces17 lb-ft23 Nm
- Oil Drain PlugUse new crush washer26 lb-ft35 Nm
- Oil Pan BoltFront section only9 lb-ft12 Nm
- Sensor Mounting Bolts9 lb-ft12 Nm
- Timing Cover Bolts - 10mmTighten in sequence33 lb-ft45 Nm
- Timing Cover Bolts - 8mmTighten in sequence18 lb-ft25 Nm
Full Engine Tune-Up4 specs
- Ignition Coil Bolt6 lb-ft8 Nm
- Spark Plugs - Aluminum HeadApply anti-seize to threads18 lb-ft24 Nm
- Throttle Body Bolts7 lb-ft10 Nm
- Valve Cover BoltsTighten in sequence7 lb-ft10 Nm
Harmonic Balancer4 specs
- Crankshaft Pulley BoltOften TTY, may need impact. Verify sequence with the service manual133 lb-ft180 Nm
- Electrical Connector Bolts6 lb-ft8 Nm
- Gasket Surface BoltsClean mating surfaces17 lb-ft23 Nm
- Sensor Mounting Bolts9 lb-ft12 Nm
Head Gasket - Single6 specs
- Exhaust Manifold NutsApply anti-seize18 lb-ft25 Nm
- Intake Manifold BoltTighten in sequence18 lb-ft25 Nm
- Cylinder Head Bolts - Step 1Always use new TTY bolts30 lb-ft40 Nm
- Cylinder Head Bolts - Step 2Tighten in sequence59 lb-ft80 Nm
- Cylinder Head Bolts - Step 3Plus 90 degrees66 lb-ft + 90°90 Nm
- Cylinder Head Bolts - Step 4Plus 90 degrees66 lb-ft + 90°90 Nm
Head Gaskets - Both16 specs
- Camshaft Bearing CapsTighten in sequence. AMG cams require precise alignment11 lb-ft15 Nm
- Camshaft Cap BoltsTighten in sequence from center outward, multiple passes10 lb-ft14 Nm
- Camshaft Sprocket BoltsHold cam with wrench on hex32 lb-ft43 Nm
- Crankshaft Pulley BoltOften TTY - check spec, may require impact133 lb-ft180 Nm
- Cylinder Head BoltsREPLACE BOLTS. AMG spec: Step 1: 26 lb-ft. Step 2: +90°. Step 3: +90°. Critical for high-boost applications26 lb-ft + 90°35 Nm
- Electrical Connector Bolts6 lb-ft8 Nm
- Exhaust Manifold Nuts18 lb-ft25 Nm
- Gasket Surface BoltsClean mating surfaces17 lb-ft23 Nm
- Intake Manifold Bolt7 lb-ft10 Nm
- Oil Drain PlugUse new crush washer26 lb-ft35 Nm
- Rocker Arm BoltsTighten with cam lobe pointing away22 lb-ft30 Nm
- Sensor Mounting Bolts7 lb-ft10 Nm
- Timing Chain Tensioner BoltInstall with pin/clip to compress18 lb-ft25 Nm
- Timing Cover Bolts - 8mmTighten in sequence15 lb-ft20 Nm
- Valve Cover BoltsTighten in sequence7 lb-ft10 Nm
- VVT Solenoid Bolt7 lb-ft10 Nm
Idle Air Control Valve4 specs
- Electrical Connector Bolts6 lb-ft8 Nm
- Gasket Surface BoltsClean mating surfaces17 lb-ft23 Nm
- IAC Valve Screws2 lb-ft3 Nm
- Sensor Mounting Bolts9 lb-ft12 Nm
Idler Pulley4 specs
- Electrical Connector Bolts6 lb-ft8 Nm
- Gasket Surface BoltsClean mating surfaces17 lb-ft23 Nm
- Idler Pulley Bolt33 lb-ft45 Nm
- Sensor Mounting Bolts9 lb-ft12 Nm
Intake Manifold7 specs
- Electrical Connector Bolts6 lb-ft8 Nm
- Fuel Rail BoltsVerify sequence with the service manual9 lb-ft12 Nm
- Gasket Surface BoltsClean mating surfaces17 lb-ft23 Nm
- Intake Manifold BoltTighten in sequence from center out. Verify sequence with the service manual7 lb-ft10 Nm
- PCV ValveVerify sequence with the service manual6 lb-ft8 Nm
- Sensor Mounting Bolts9 lb-ft12 Nm
- Throttle Body BoltsVerify sequence with the service manual7 lb-ft10 Nm
Intake Manifold Gasket3 specs
- Fuel Rail Bolts9 lb-ft12 Nm
- Intake Manifold BoltTighten in sequence from center out7 lb-ft10 Nm
- Throttle Body Bolts7 lb-ft10 Nm
Intercooler5 specs
- Charge Pipe Clamps3 lb-ft4 Nm
- Electrical Connector Bolts6 lb-ft8 Nm
- Gasket Surface BoltsClean mating surfaces17 lb-ft23 Nm
- Intercooler Mounting Bolts11 lb-ft15 Nm
- Sensor Mounting Bolts9 lb-ft12 Nm
Knock Sensor4 specs
- Electrical Connector Bolts6 lb-ft8 Nm
- Gasket Surface BoltsClean mating surfaces17 lb-ft23 Nm
- Knock SensorTorque critical for function15 lb-ft20 Nm
- Sensor Mounting Bolts9 lb-ft12 Nm
Lifter - Single7 specs
- Electrical Connector Bolts6 lb-ft8 Nm
- Gasket Surface BoltsClean mating surfaces17 lb-ft23 Nm
- Intake Manifold Bolt18 lb-ft25 Nm
- Rocker Arm BoltsTighten with cam lobe pointing away22 lb-ft30 Nm
- Rocker Arm Shaft BoltsTighten evenly in sequence18 lb-ft25 Nm
- Sensor Mounting Bolts9 lb-ft12 Nm
- Valve Cover BoltsTighten in sequence7 lb-ft10 Nm
Lifters/Tappets - All10 specs
- Camshaft Bearing Cap BoltsTighten in sequence, 3 passes10 lb-ft14 Nm
- Camshaft Cap BoltsTighten in sequence from center outward, multiple passes10 lb-ft14 Nm
- Camshaft Position Sensor7 lb-ft10 Nm
- Electrical Connector Bolts6 lb-ft8 Nm
- Gasket Surface BoltsClean mating surfaces17 lb-ft23 Nm
- Intake Manifold Bolt18 lb-ft25 Nm
- Rocker Arm BoltsTighten with cam lobe pointing away22 lb-ft30 Nm
- Rocker Arm Shaft BoltsTighten evenly in sequence18 lb-ft25 Nm
- Sensor Mounting Bolts9 lb-ft12 Nm
- Valve Cover BoltsTighten in sequence7 lb-ft10 Nm
Long Block Replacement16 specs
- Camshaft Cap BoltsTighten in sequence from center outward, multiple passes10 lb-ft14 Nm
- Connecting Rod BoltsTTY - critical torque plus angle33 lb-ft45 Nm
- Cylinder Head BoltsTTY - tighten in sequence plus angle32 lb-ft43 Nm
- Electrical Connector Bolts6 lb-ft8 Nm
- Exhaust Manifold NutsApply anti-seize, work hot-to-cold18 lb-ft25 Nm
- Flywheel BoltsOften TTY, tighten in star pattern33 lb-ft45 Nm
- Gasket Surface BoltsClean mating surfaces17 lb-ft23 Nm
- Intake Manifold Bolt7 lb-ft10 Nm
- Main Bearing Cap BoltsTTY - tighten in sequence plus angle55 lb-ft75 Nm
- Oil Drain PlugUse new crush washer26 lb-ft35 Nm
- Oil Pan Bolt9 lb-ft12 Nm
- Sensor Mounting Bolts9 lb-ft12 Nm
- Timing Chain Tensioner BoltInstall with pin/clip to compress59 lb-ft80 Nm
- Timing Cover Bolts - 8mmTighten in sequence15 lb-ft20 Nm
- Transmission-to-Engine Bolts32 lb-ft43 Nm
- Valve Cover BoltsTighten in sequence7 lb-ft10 Nm
Main Bearings9 specs
- Electrical Connector Bolts6 lb-ft8 Nm
- Flywheel BoltsOften TTY, tighten in star pattern. Verify sequence with the service manual33 lb-ft45 Nm
- Gasket Surface BoltsClean mating surfaces17 lb-ft23 Nm
- Main Bearing Cap BoltsREPLACE BOLTS. Step 1: 30 lb-ft. Step 2: +90°22 lb-ft + 90°30 Nm
- Oil Drain PlugUse new crush washer. Verify sequence with the service manual26 lb-ft35 Nm
- Oil Pan BoltTighten in sequence. Verify sequence with the service manual9 lb-ft12 Nm
- Oil Pump Pickup TubeVerify sequence with the service manual9 lb-ft12 Nm
- Sensor Mounting Bolts9 lb-ft12 Nm
- Transmission-to-Engine BoltsVerify sequence with the service manual33 lb-ft45 Nm
Manifold Absolute Pressure Sensor4 specs
- Electrical Connector Bolts6 lb-ft8 Nm
- Gasket Surface BoltsClean mating surfaces17 lb-ft23 Nm
- MAP Sensor Screws2 lb-ft3 Nm
- Sensor Mounting Bolts9 lb-ft12 Nm
Mass Air Flow Sensor5 specs
- Air Intake Clamps2 lb-ft3 Nm
- Electrical Connector Bolts6 lb-ft8 Nm
- Gasket Surface BoltsClean mating surfaces17 lb-ft23 Nm
- MAF Sensor Screws2 lb-ft3 Nm
- Sensor Mounting Bolts9 lb-ft12 Nm
Oil Change2 specs
- Oil Drain PlugUse new crush washer26 lb-ft35 Nm
- Oil Filter Housing CapFor cartridge-type filters18 lb-ft25 Nm
Oil Level Sensor5 specs
- Electrical Connector Bolts6 lb-ft8 Nm
- Gasket Surface BoltsClean mating surfaces17 lb-ft23 Nm
- Oil Level Sensor11 lb-ft15 Nm
- Oil Pan BoltIf access needed9 lb-ft12 Nm
- Sensor Mounting Bolts9 lb-ft12 Nm
Oil Pan Gasket2 specs
- Oil Drain PlugUse new crush washer26 lb-ft35 Nm
- Oil Pan BoltTighten in sequence from center outward9 lb-ft12 Nm
Oil Pan Replacement6 specs
- Electrical Connector Bolts6 lb-ft8 Nm
- Gasket Surface BoltsClean mating surfaces17 lb-ft23 Nm
- Oil Drain PlugUse new crush washer26 lb-ft35 Nm
- Oil Pan BoltTighten in sequence9 lb-ft12 Nm
- Oil Pump Pickup Tube9 lb-ft12 Nm
- Sensor Mounting Bolts9 lb-ft12 Nm
Oil Pressure Sensor4 specs
- Electrical Connector Bolts6 lb-ft8 Nm
- Gasket Surface BoltsClean mating surfaces17 lb-ft23 Nm
- Oil Pressure SensorUse thread sealant15 lb-ft20 Nm
- Sensor Mounting Bolts9 lb-ft12 Nm
Oil Pump8 specs
- Electrical Connector Bolts6 lb-ft8 Nm
- Gasket Surface BoltsClean mating surfaces7 lb-ft10 Nm
- Oil Drain PlugUse new crush washer26 lb-ft35 Nm
- Oil Pan Bolt15 lb-ft20 Nm
- Oil Pump Bolts15 lb-ft20 Nm
- Oil Pump Pickup Tube9 lb-ft12 Nm
- Sensor Mounting Bolts9 lb-ft12 Nm
- Timing Cover Bolts - 8mmTighten in sequence15 lb-ft20 Nm
PCV Valve4 specs
- Electrical Connector Bolts6 lb-ft8 Nm
- Gasket Surface BoltsClean mating surfaces7 lb-ft9 Nm
- PCV ValveHand tight usually6 lb-ft8 Nm
- Sensor Mounting Bolts9 lb-ft12 Nm
Piston - Single7 specs
- Connecting Rod BoltsTTY - critical torque plus angle33 lb-ft45 Nm
- Cylinder Head BoltsTTY - tighten in sequence plus angle22 lb-ft30 Nm
- Electrical Connector Bolts6 lb-ft8 Nm
- Gasket Surface BoltsClean mating surfaces7 lb-ft10 Nm
- Oil Drain PlugUse new crush washer26 lb-ft35 Nm
- Oil Pan Bolt15 lb-ft20 Nm
- Sensor Mounting Bolts9 lb-ft12 Nm
Piston Rings - All9 specs
- Connecting Rod BoltsTTY - critical torque plus angle33 lb-ft45 Nm
- Cylinder Head BoltsTTY - tighten in sequence plus angle22 lb-ft30 Nm
- Electrical Connector Bolts6 lb-ft8 Nm
- Gasket Surface BoltsClean mating surfaces7 lb-ft10 Nm
- Main Bearing Cap BoltsTTY - tighten in sequence plus angle18 lb-ft25 Nm
- Oil Drain PlugUse new crush washer26 lb-ft35 Nm
- Oil Pan BoltTighten in sequence15 lb-ft20 Nm
- Oil Pump Pickup Tube9 lb-ft12 Nm
- Sensor Mounting Bolts9 lb-ft12 Nm
Pistons - All9 specs
- Connecting Rod BoltsTTY - critical torque plus angle33 lb-ft45 Nm
- Cylinder Head BoltsTTY - tighten in sequence plus angle22 lb-ft30 Nm
- Electrical Connector Bolts6 lb-ft8 Nm
- Gasket Surface BoltsClean mating surfaces7 lb-ft10 Nm
- Main Bearing Cap BoltsTTY - tighten in sequence plus angle18 lb-ft25 Nm
- Oil Drain PlugUse new crush washer26 lb-ft35 Nm
- Oil Pan Bolt15 lb-ft20 Nm
- Oil Pump Pickup Tube9 lb-ft12 Nm
- Sensor Mounting Bolts9 lb-ft12 Nm
Rear Main Seal9 specs
- Electrical Connector Bolts6 lb-ft8 Nm
- Flexplate BoltsAutomatic transmissions33 lb-ft45 Nm
- Flywheel BoltsOften TTY, tighten in star pattern70 lb-ft95 Nm
- Gasket Surface BoltsClean mating surfaces7 lb-ft10 Nm
- Oil Drain PlugUse new crush washer26 lb-ft35 Nm
- Oil Pan BoltRear section9 lb-ft12 Nm
- Rear Main Seal Housing9 lb-ft12 Nm
- Sensor Mounting Bolts9 lb-ft12 Nm
- Transmission-to-Engine Bolts33 lb-ft45 Nm
Rocker Arms - All7 specs
- Electrical Connector Bolts6 lb-ft8 Nm
- Gasket Surface BoltsClean mating surfaces7 lb-ft10 Nm
- Intake Manifold BoltIf pushrods18 lb-ft25 Nm
- Rocker Arm BoltsTighten with cam lobe pointing away22 lb-ft30 Nm
- Rocker Arm Shaft BoltsTighten evenly in sequence18 lb-ft25 Nm
- Sensor Mounting Bolts9 lb-ft12 Nm
- Valve Cover BoltsTighten in sequence7 lb-ft10 Nm
Serpentine Belt2 specs
- Belt Tensioner Bolt41 lb-ft55 Nm
- Idler Pulley Bolt33 lb-ft45 Nm
Serpentine Belt Tensioner4 specs
- Belt Tensioner Bolt30 lb-ft40 Nm
- Electrical Connector Bolts6 lb-ft8 Nm
- Gasket Surface BoltsClean mating surfaces17 lb-ft23 Nm
- Sensor Mounting Bolts9 lb-ft12 Nm
Short Block Replacement12 specs
- Connecting Rod BoltsTTY - critical torque plus angle33 lb-ft45 Nm
- Crankshaft Pulley BoltOften TTY - check spec, may require impact133 lb-ft180 Nm
- Electrical Connector Bolts6 lb-ft8 Nm
- Flywheel BoltsOften TTY, tighten in star pattern33 lb-ft45 Nm
- Gasket Surface BoltsClean mating surfaces17 lb-ft23 Nm
- Main Bearing Cap BoltsTTY - tighten in sequence plus angle22 lb-ft30 Nm
- Oil Drain PlugUse new crush washer26 lb-ft35 Nm
- Oil Pan Bolt9 lb-ft12 Nm
- Oil Pump Bolts15 lb-ft20 Nm
- Sensor Mounting Bolts9 lb-ft12 Nm
- Timing Cover Bolts - 8mmTighten in sequence15 lb-ft20 Nm
- Transmission-to-Engine Bolts33 lb-ft45 Nm
Throttle Body2 specs
- Air Intake Hose Clamps2 lb-ft3 Nm
- Throttle Body Bolts7 lb-ft10 Nm
Throttle Position Sensor4 specs
- Electrical Connector Bolts6 lb-ft8 Nm
- Gasket Surface BoltsClean mating surfaces17 lb-ft23 Nm
- Sensor Mounting Bolts9 lb-ft12 Nm
- TPS Screws2 lb-ft3 Nm
Timing Chain5 specs
- Camshaft Sprocket Bolts30 lb-ft40 Nm
- Crankshaft Pulley BoltOften TTY - check specs133 lb-ft + 90°180 Nm
- Timing Chain Guide Bolts9 lb-ft12 Nm
- Timing Chain Tensioner59 lb-ft80 Nm
- Timing Cover BoltTighten in sequence9 lb-ft12 Nm
Timing Chain Guide11 specs
- Camshaft Sprocket Bolts30 lb-ft40 Nm
- Crankshaft Pulley Bolt150 lb-ft203 Nm
- Electrical Connector Bolts6 lb-ft8 Nm
- Gasket Surface BoltsClean mating surfaces17 lb-ft23 Nm
- Guide Bolts7 lb-ft10 Nm
- Sensor Mounting Bolts9 lb-ft12 Nm
- Tensioner Bolt17 lb-ft23 Nm
- Timing Chain Guide BoltsReplace if worn9 lb-ft12 Nm
- Timing Cover Bolt15 lb-ft20 Nm
- Timing Cover Bolts - 8mmTighten in sequence15 lb-ft20 Nm
- Valve Cover BoltsTighten in sequence7 lb-ft10 Nm
Timing Chain Kit18 specs
- Cam Phaser BoltApply threadlocker, hold cam stationary30 lb-ft40 Nm
- Camshaft Sprocket BoltsHold cam with wrench on hex30 lb-ft40 Nm
- Crankshaft Pulley BoltOften TTY - check spec, may require impact133 lb-ft180 Nm
- Electrical Connector Bolts6 lb-ft8 Nm
- Gasket Surface BoltsClean mating surfaces17 lb-ft23 Nm
- Guide Bolts7 lb-ft10 Nm
- Oil Drain PlugUse new crush washer26 lb-ft35 Nm
- Oil Pump Bolts15 lb-ft20 Nm
- Sensor Mounting Bolts9 lb-ft12 Nm
- Tensioner Bolt17 lb-ft23 Nm
- Timing Chain Guide BoltsReplace if worn9 lb-ft12 Nm
- Timing Chain Idler Sprocket22 lb-ft30 Nm
- Timing Chain Tensioner BoltInstall with pin/clip to compress59 lb-ft80 Nm
- Timing Cover Bolt15 lb-ft20 Nm
- Timing Cover Bolts - 10mmTighten in sequence33 lb-ft45 Nm
- Timing Cover Bolts - 6mmTighten in sequence7 lb-ft10 Nm
- Timing Cover Bolts - 8mmTighten in sequence15 lb-ft20 Nm
- Valve Cover BoltsTighten in sequence7 lb-ft10 Nm
Timing Chain Tensioner11 specs
- Camshaft Sprocket Bolts30 lb-ft40 Nm
- Crankshaft Pulley Bolt150 lb-ft203 Nm
- Electrical Connector Bolts6 lb-ft8 Nm
- Gasket Surface BoltsClean mating surfaces17 lb-ft23 Nm
- Guide Bolts7 lb-ft10 Nm
- Sensor Mounting Bolts9 lb-ft12 Nm
- Tensioner Bolt59 lb-ft80 Nm
- Timing Chain Tensioner BoltInstall with pin/clip to compress59 lb-ft80 Nm
- Timing Cover Bolt15 lb-ft20 Nm
- Timing Cover Bolts - 8mmTighten in sequence15 lb-ft20 Nm
- Valve Cover BoltsTighten in sequence7 lb-ft10 Nm
Transmission Mount7 specs
- Crossmember Bolt33 lb-ft45 Nm
- Drain PlugUse new washer15 lb-ft20 Nm
- Fill Plug15 lb-ft20 Nm
- Flywheel BoltsOften TTY, tighten in star pattern33 lb-ft45 Nm
- Transmission Drain PlugUse new crush washer if equipped15 lb-ft20 Nm
- Transmission Mount Bolts30 lb-ft40 Nm
- Transmission Pan BoltsTighten in criss-cross pattern9 lb-ft12 Nm
Turbo Wastegate Actuator3 specs
- Electrical Connector Bolts6 lb-ft8 Nm
- Gasket Surface BoltsClean mating surfaces17 lb-ft23 Nm
- Sensor Mounting Bolts9 lb-ft12 Nm
Turbocharger12 specs
- Coolant Line Fittings11 lb-ft15 Nm
- Electrical Connector Bolts6 lb-ft8 Nm
- Exhaust Manifold NutsApply anti-seize, work hot-to-cold18 lb-ft25 Nm
- Gasket Surface BoltsClean mating surfaces17 lb-ft23 Nm
- Heat Shield Bolts7 lb-ft10 Nm
- Oil Feed LineUse new crush washers15 lb-ft20 Nm
- Oil Return Line7 lb-ft10 Nm
- Sensor Mounting Bolts9 lb-ft12 Nm
- Turbo Oil Feed Banjo BoltNew crush washers. Prime turbo before first start18 lb-ft24 Nm
- Turbo to Exhaust Manifold StudsUse anti-seize on studs15 lb-ft20 Nm
- Turbo-to-Downpipe Bolts18 lb-ft25 Nm
- Turbo-to-Manifold BoltsApply anti-seize18 lb-ft25 Nm
Valve Adjustment6 specs
- Electrical Connector Bolts6 lb-ft8 Nm
- Gasket Surface BoltsClean mating surfaces17 lb-ft23 Nm
- Rocker Arm BoltsTighten with cam lobe pointing away22 lb-ft30 Nm
- Sensor Mounting Bolts9 lb-ft12 Nm
- Valve Cover BoltsTighten in sequence7 lb-ft10 Nm
- Valve Lash Adjusting Screw Lock NutHold screw while tightening15 lb-ft20 Nm
Valve Cover Gasket - Single2 specs
- Spark Plug Tube SealsIf equipped with separate seals9 lb-ft12 Nm
- Valve Cover BoltsTighten in sequence7 lb-ft10 Nm
Valve Cover Gaskets - Both7 specs
- Electrical Connector Bolts6 lb-ft8 Nm
- Gasket Surface BoltsClean mating surfaces7 lb-ft10 Nm
- Ignition Coil Bolt6 lb-ft8 Nm
- Intake Manifold BoltIf required18 lb-ft25 Nm
- Sensor Mounting Bolts9 lb-ft12 Nm
- Spark Plugs - Aluminum HeadApply anti-seize to threads18 lb-ft24 Nm
- Valve Cover BoltsTighten in sequence7 lb-ft10 Nm
Valve Job - Complete12 specs
- Camshaft Cap BoltsTighten in sequence from center outward, multiple passes10 lb-ft14 Nm
- Camshaft Sprocket BoltsHold cam with wrench on hex30 lb-ft40 Nm
- Cylinder Head BoltsTTY - tighten in sequence plus angle24 lb-ft33 Nm
- Electrical Connector Bolts6 lb-ft8 Nm
- Exhaust Manifold NutsApply anti-seize, work hot-to-cold18 lb-ft25 Nm
- Gasket Surface BoltsClean mating surfaces7 lb-ft10 Nm
- Intake Manifold Bolt7 lb-ft10 Nm
- Rocker Arm BoltsTighten with cam lobe pointing away22 lb-ft30 Nm
- Sensor Mounting Bolts9 lb-ft12 Nm
- Timing Chain Tensioner BoltInstall with pin/clip to compress18 lb-ft25 Nm
- Timing Cover Bolts - 8mmTighten in sequence15 lb-ft20 Nm
- Valve Cover BoltsTighten in sequence7 lb-ft10 Nm
Valve Seals8 specs
- Camshaft Cap BoltsTighten in sequence from center outward, multiple passes10 lb-ft14 Nm
- Electrical Connector Bolts6 lb-ft8 Nm
- Gasket Surface BoltsClean mating surfaces7 lb-ft10 Nm
- Rocker Arm BoltsTighten with cam lobe pointing away22 lb-ft30 Nm
- Rocker Arm Shaft BoltsTighten evenly in sequence18 lb-ft25 Nm
- Sensor Mounting Bolts9 lb-ft12 Nm
- Spark Plugs - Aluminum HeadApply anti-seize to threads18 lb-ft24 Nm
- Valve Cover BoltsTighten in sequence7 lb-ft10 Nm
Valve Spring - Single6 specs
- Electrical Connector Bolts6 lb-ft8 Nm
- Gasket Surface BoltsClean mating surfaces7 lb-ft10 Nm
- Rocker Arm BoltsTighten with cam lobe pointing away22 lb-ft30 Nm
- Sensor Mounting Bolts9 lb-ft12 Nm
- Spark Plugs - Aluminum HeadApply anti-seize to threads18 lb-ft24 Nm
- Valve Cover BoltsTighten in sequence7 lb-ft10 Nm
Valve Springs - All8 specs
- Camshaft Cap BoltsTighten in sequence from center outward, multiple passes10 lb-ft14 Nm
- Electrical Connector Bolts6 lb-ft8 Nm
- Gasket Surface BoltsClean mating surfaces7 lb-ft10 Nm
- Rocker Arm BoltsTighten with cam lobe pointing away22 lb-ft30 Nm
- Rocker Arm Shaft BoltsTighten evenly in sequence18 lb-ft25 Nm
- Sensor Mounting Bolts9 lb-ft12 Nm
- Spark Plugs - Aluminum HeadApply anti-seize to threads18 lb-ft24 Nm
- Valve Cover BoltsTighten in sequence7 lb-ft10 Nm
Variable Valve Timing Actuator10 specs
- Cam Phaser BoltApply threadlocker, hold cam stationary30 lb-ft40 Nm
- Camshaft Sprocket BoltsHold cam with wrench on hex30 lb-ft40 Nm
- Crankshaft Pulley BoltOften TTY - check spec, may require impact133 lb-ft180 Nm
- Electrical Connector Bolts6 lb-ft8 Nm
- Gasket Surface BoltsClean mating surfaces7 lb-ft10 Nm
- Sensor Mounting Bolts9 lb-ft12 Nm
- Timing Chain Tensioner BoltInstall with pin/clip to compress18 lb-ft25 Nm
- Timing Cover Bolts - 8mmTighten in sequence15 lb-ft20 Nm
- Valve Cover BoltsTighten in sequence7 lb-ft10 Nm
- VVT Solenoid Bolt7 lb-ft10 Nm
VVT Solenoid - Single5 specs
- Electrical Connector Bolts6 lb-ft8 Nm
- Gasket Surface BoltsClean mating surfaces7 lb-ft9 Nm
- Sensor Mounting Bolts9 lb-ft12 Nm
- Valve Cover BoltsTighten in sequence7 lb-ft10 Nm
- VVT Solenoid Bolt7 lb-ft10 Nm
VVT Solenoids - All6 specs
- Camshaft Position Sensor7 lb-ft10 Nm
- Electrical Connector Bolts6 lb-ft8 Nm
- Gasket Surface BoltsClean mating surfaces7 lb-ft9 Nm
- Sensor Mounting Bolts9 lb-ft12 Nm
- Valve Cover BoltsTighten in sequence7 lb-ft10 Nm
- VVT Solenoid Bolt7 lb-ft10 Nm

Cooling

Coolant Bypass Pipe8 specs
- Bleed ScrewOpen during fill6 lb-ft8 Nm
- Coolant Drain Plug11 lb-ft15 Nm
- Drain PetcockHand tight6 lb-ft8 Nm
- Fan Bolts9 lb-ft12 Nm
- Hose Clamps2 lb-ft3 Nm
- Pump BoltsTorque in sequence15 lb-ft20 Nm
- Thermostat Housing Bolt11 lb-ft15 Nm
- Water Pump BoltsTighten in criss-cross pattern15 lb-ft20 Nm
Coolant Flush12 specs
- Air Box Clips4 lb-ft5 Nm
- Bleed ScrewOpen during fill5 lb-ft7 Nm
- Block Drain PlugIf equipped, use new washer18 lb-ft25 Nm
- Connector Bolts6 lb-ft8 Nm
- Coolant Hose Clamps3 lb-ft4 Nm
- Drain Petcock4 lb-ft5 Nm
- Drain Plug11 lb-ft15 Nm
- Hose Clamps3 lb-ft5 Nm
- Oil Drain PlugUse new crush washer26 lb-ft35 Nm
- Pump Bolts15 lb-ft20 Nm
- Radiator CapHand tight1 lb-ft1 Nm
- Wheel Lug NutsTorque in star pattern133 lb-ft180 Nm
Coolant Reservoir9 specs
- Bleed ScrewOpen during fill6 lb-ft8 Nm
- Coolant Drain Plug11 lb-ft15 Nm
- Drain PetcockHand tight6 lb-ft8 Nm
- Fan Bolts9 lb-ft12 Nm
- Hose ClampsDo not overtighten3 lb-ft4 Nm
- Pump BoltsTorque in sequence15 lb-ft20 Nm
- Reservoir Mounting Bolts6 lb-ft8 Nm
- Thermostat Housing Bolt7 lb-ft10 Nm
- Water Pump BoltsTighten in criss-cross pattern15 lb-ft20 Nm
Coolant Temperature Sensor8 specs
- Bleed ScrewOpen during fill6 lb-ft8 Nm
- Coolant Drain Plug11 lb-ft15 Nm
- Drain PetcockHand tight6 lb-ft8 Nm
- Fan Bolts9 lb-ft12 Nm
- Hose Clamps2 lb-ft3 Nm
- Pump BoltsTorque in sequence15 lb-ft20 Nm
- Thermostat Housing Bolt11 lb-ft15 Nm
- Water Pump BoltsTighten in criss-cross pattern15 lb-ft20 Nm
Cooling Fan Assembly7 specs
- Coolant Drain Plug11 lb-ft15 Nm
- Drain PetcockHand tight6 lb-ft8 Nm
- Fan Bolts9 lb-ft12 Nm
- Hose Clamps2 lb-ft3 Nm
- Pump BoltsTorque in sequence15 lb-ft20 Nm
- Thermostat Housing Bolt11 lb-ft15 Nm
- Water Pump BoltsTighten in criss-cross pattern15 lb-ft20 Nm
Cooling Fan Clutch6 specs
- Drain PetcockHand tight6 lb-ft8 Nm
- Fan Bolts9 lb-ft12 Nm
- Hose Clamps2 lb-ft3 Nm
- Pump BoltsTorque in sequence15 lb-ft20 Nm
- Thermostat Housing Bolt11 lb-ft15 Nm
- Water Pump BoltsTighten in criss-cross pattern15 lb-ft20 Nm
Cooling Fan Motor7 specs
- Drain PetcockHand tight6 lb-ft8 Nm
- Electrical Connector4 lb-ft5 Nm
- Fan Bolts9 lb-ft12 Nm
- Fan Motor Bolts6 lb-ft8 Nm
- Hose ClampsDo not overtighten3 lb-ft4 Nm
- Pump BoltsTorque in sequence15 lb-ft20 Nm
- Thermostat Housing Bolt7 lb-ft10 Nm
Cooling Fan Relay5 specs
- Drain PetcockHand tight6 lb-ft8 Nm
- Fan Bolts9 lb-ft12 Nm
- Pump BoltsTorque in sequence15 lb-ft20 Nm
- Thermostat Housing Bolt11 lb-ft15 Nm
- Water Pump BoltsTighten in criss-cross pattern15 lb-ft20 Nm
Engine Oil Cooler7 specs
- Coolant Drain Plug11 lb-ft15 Nm
- Drain PetcockHand tight6 lb-ft8 Nm
- Fan Bolts9 lb-ft12 Nm
- Hose Clamps2 lb-ft3 Nm
- Pump BoltsTorque in sequence15 lb-ft20 Nm
- Thermostat Housing Bolt11 lb-ft15 Nm
- Water Pump BoltsTighten in criss-cross pattern15 lb-ft20 Nm
Heater Control Valve6 specs
- Drain PetcockHand tight6 lb-ft8 Nm
- Fan Bolts9 lb-ft12 Nm
- Hose Clamps2 lb-ft3 Nm
- Pump BoltsTorque in sequence7 lb-ft10 Nm
- Thermostat Housing Bolt7 lb-ft10 Nm
- Valve Mounting6 lb-ft8 Nm
Heater Core8 specs
- Dashboard Screws2 lb-ft3 Nm
- Drain PetcockHand tight6 lb-ft8 Nm
- Fan Bolts9 lb-ft12 Nm
- Heater Core Mounting6 lb-ft8 Nm
- Heater Hose Clamps2 lb-ft3 Nm
- Hose ClampsDo not overtighten3 lb-ft4 Nm
- Pump BoltsTorque in sequence7 lb-ft10 Nm
- Thermostat Housing Bolt7 lb-ft10 Nm
Heater Hoses7 specs
- Coolant Drain Plug11 lb-ft15 Nm
- Drain PetcockHand tight6 lb-ft8 Nm
- Fan Bolts9 lb-ft12 Nm
- Hose Clamps2 lb-ft3 Nm
- Pump BoltsTorque in sequence7 lb-ft10 Nm
- Thermostat Housing Bolt11 lb-ft15 Nm
- Water Pump BoltsTighten in criss-cross pattern7 lb-ft10 Nm
Radiator4 specs
- Drain PetcockPlastic - hand tight4 lb-ft5 Nm
- Radiator Mounting BoltDo not overtighten plastic mounts9 lb-ft12 Nm
- Transmission Cooler LinesIf equipped18 lb-ft25 Nm
- Upper/Lower Hose Clamps2 lb-ft3 Nm
Radiator Cap5 specs
- Drain PetcockHand tight6 lb-ft8 Nm
- Fan Bolts9 lb-ft12 Nm
- Pump BoltsTorque in sequence15 lb-ft20 Nm
- Thermostat Housing Bolt11 lb-ft15 Nm
- Water Pump BoltsTighten in criss-cross pattern15 lb-ft20 Nm
Radiator Hose - Lower5 specs
- Drain PetcockHand tight6 lb-ft8 Nm
- Fan Bolts9 lb-ft12 Nm
- Hose Clamps2 lb-ft3 Nm
- Pump BoltsTorque in sequence15 lb-ft20 Nm
- Thermostat Housing Bolt7 lb-ft10 Nm
Radiator Hose - Upper5 specs
- Drain PetcockHand tight6 lb-ft8 Nm
- Fan Bolts9 lb-ft12 Nm
- Hose Clamps2 lb-ft3 Nm
- Pump BoltsTorque in sequence15 lb-ft20 Nm
- Thermostat Housing Bolt7 lb-ft10 Nm
Radiator Hoses - Both7 specs
- Coolant Drain Plug11 lb-ft15 Nm
- Drain PetcockHand tight6 lb-ft8 Nm
- Fan Bolts9 lb-ft12 Nm
- Hose Clamps2 lb-ft3 Nm
- Pump BoltsTorque in sequence15 lb-ft20 Nm
- Thermostat Housing Bolt11 lb-ft15 Nm
- Water Pump BoltsTighten in criss-cross pattern15 lb-ft20 Nm
Radiator Removal and Service4 specs
- Drain PetcockPlastic - hand-tight only4 lb-ft5 Nm
- Fan Shroud Bolts7 lb-ft10 Nm
- Radiator Mounting BoltDo not overtighten plastic mounts9 lb-ft12 Nm
- Transmission Cooler LinesIf equipped, use new washers18 lb-ft25 Nm
Thermostat2 specs
- Coolant Temperature SensorUse thread sealant15 lb-ft20 Nm
- Thermostat Housing Bolt11 lb-ft15 Nm
Thermostat Housing8 specs
- Coolant Drain Plug11 lb-ft15 Nm
- Coolant Hose Clamps3 lb-ft5 Nm
- Drain PetcockHand tight6 lb-ft8 Nm
- Fan Bolts9 lb-ft12 Nm
- Hose Clamps2 lb-ft3 Nm
- Pump BoltsTorque in sequence21 lb-ft28 Nm
- Thermostat Housing Bolt11 lb-ft15 Nm
- Water Pump BoltsTighten in criss-cross pattern18 lb-ft25 Nm
Water Pump3 specs
- Hose ClampsSpring clamps preferred2 lb-ft3 Nm
- Thermostat Housing Bolt11 lb-ft15 Nm
- Water Pump BoltsTighten in criss-cross pattern15 lb-ft20 Nm

Ignition

Ignition Coil - Single3 specs
- Connector Bolts6 lb-ft8 Nm
- Ignition Coil Bolt6 lb-ft8 Nm
- Spark Plugs - Aluminum HeadApply anti-seize to threads18 lb-ft25 Nm
Ignition Coils - All3 specs
- Connector Bolts6 lb-ft8 Nm
- Ignition Coil Bolt6 lb-ft8 Nm
- Spark Plugs - Aluminum HeadApply anti-seize to threads18 lb-ft25 Nm
Ignition Control Module3 specs
- Connector Bolts6 lb-ft8 Nm
- Ignition Coil Bolt6 lb-ft8 Nm
- Spark Plugs - Aluminum HeadApply anti-seize to threads18 lb-ft25 Nm
Ignition Lock Cylinder3 specs
- Connector Bolts6 lb-ft8 Nm
- Ignition Coil Bolt6 lb-ft8 Nm
- Spark Plugs - Aluminum HeadApply anti-seize to threads18 lb-ft25 Nm
Ignition Switch3 specs
- Connector Bolts6 lb-ft8 Nm
- Steering Column Bolts15 lb-ft20 Nm
- Switch Mounting Screws4 lb-ft5 Nm
Spark Plugs8 specs
- Air Box Clips4 lb-ft5 Nm
- Connector Bolts6 lb-ft8 Nm
- Engine Cover Clips2 lb-ft3 Nm
- Ignition Coil Bolt6 lb-ft8 Nm
- Oil Drain PlugUse new crush washer26 lb-ft35 Nm
- Spark PlugGap before install17 lb-ft23 Nm
- Spark Plugs - Aluminum HeadApply anti-seize to threads18 lb-ft24 Nm
- Wheel Lug NutsTorque in star pattern133 lb-ft180 Nm

Fuel system

Charcoal Canister5 specs
- Filter Bracket9 lb-ft12 Nm
- Fuel Line FittingsUse new O-rings15 lb-ft20 Nm
- Hose Clamps2 lb-ft3 Nm
- Pressure Regulator Screws6 lb-ft8 Nm
- Pump Mounting6 lb-ft8 Nm
EVAP Purge Valve5 specs
- Filter Bracket9 lb-ft12 Nm
- Fuel Line FittingsUse new O-rings18 lb-ft25 Nm
- Hose Clamps2 lb-ft3 Nm
- Pressure Regulator Screws6 lb-ft8 Nm
- Pump Mounting12 lb-ft16 Nm
EVAP Vent Valve5 specs
- Filter Bracket9 lb-ft12 Nm
- Fuel Line FittingsUse new O-rings18 lb-ft25 Nm
- Hose Clamps2 lb-ft3 Nm
- Pressure Regulator Screws6 lb-ft8 Nm
- Pump Mounting12 lb-ft16 Nm
Fuel Cap4 specs
- Filter Bracket9 lb-ft12 Nm
- Fuel Line FittingsUse new O-rings18 lb-ft25 Nm
- Pressure Regulator Screws6 lb-ft8 Nm
- Pump Mounting12 lb-ft16 Nm
Fuel Filler Neck6 specs
- Filler Neck Bolts7 lb-ft10 Nm
- Filter Bracket9 lb-ft12 Nm
- Fuel Rail Bolts17 lb-ft23 Nm
- Hose Clamps2 lb-ft3 Nm
- Pressure Regulator Screws6 lb-ft8 Nm
- Pump Mounting12 lb-ft16 Nm
Fuel Filter7 specs
- Air Box Clips4 lb-ft5 Nm
- Connector Bolts6 lb-ft8 Nm
- Filter Bracket Bolt12 lb-ft16 Nm
- Fuel Filter Bracket Bolt7 lb-ft10 Nm
- Fuel Line FittingsIf threaded type18 lb-ft25 Nm
- Oil Drain PlugUse new crush washer26 lb-ft35 Nm
- Wheel Lug NutsTorque in star pattern133 lb-ft180 Nm
Fuel Filter - In-Tank6 specs
- Filter Bracket9 lb-ft12 Nm
- Filter Bracket Bolt12 lb-ft16 Nm
- Fuel Line FittingsUse new O-rings18 lb-ft25 Nm
- Hose Clamps2 lb-ft3 Nm
- Pressure Regulator Screws6 lb-ft8 Nm
- Pump Mounting12 lb-ft16 Nm
Fuel Injector - Single6 specs
- Filter Bracket9 lb-ft12 Nm
- Fuel Line FittingsUse new O-rings18 lb-ft25 Nm
- Fuel Rail Bolts9 lb-ft12 Nm
- Hose Clamps2 lb-ft3 Nm
- Pressure Regulator Screws6 lb-ft8 Nm
- Pump Mounting12 lb-ft16 Nm
Fuel Injector Cleaning6 specs
- Filter Bracket9 lb-ft12 Nm
- Fuel Line FittingsUse new O-rings18 lb-ft25 Nm
- Fuel Rail Bolts9 lb-ft12 Nm
- Hose Clamps2 lb-ft3 Nm
- Pressure Regulator Screws6 lb-ft8 Nm
- Pump Mounting12 lb-ft16 Nm
Fuel Injectors - All6 specs
- Filter Bracket9 lb-ft12 Nm
- Fuel Line FittingsUse new O-rings18 lb-ft25 Nm
- Fuel Rail Bolts9 lb-ft12 Nm
- Hose Clamps2 lb-ft3 Nm
- Pressure Regulator Screws6 lb-ft8 Nm
- Pump Mounting12 lb-ft16 Nm
Fuel Level Sensor5 specs
- Filter Bracket9 lb-ft12 Nm
- Fuel Line FittingsUse new O-rings18 lb-ft25 Nm
- Hose Clamps2 lb-ft3 Nm
- Pressure Regulator Screws6 lb-ft8 Nm
- Pump Mounting12 lb-ft16 Nm
Fuel Line - High Pressure6 specs
- Filter Bracket9 lb-ft12 Nm
- Fuel Line FittingsUse new O-rings18 lb-ft25 Nm
- Fuel Rail Bolts9 lb-ft12 Nm
- Hose Clamps2 lb-ft3 Nm
- Pressure Regulator Screws6 lb-ft8 Nm
- Pump Mounting12 lb-ft16 Nm
Fuel Line - Return6 specs
- Filter Bracket9 lb-ft12 Nm
- Fuel Line FittingsUse new O-rings18 lb-ft25 Nm
- Fuel Rail Bolts9 lb-ft12 Nm
- Hose Clamps2 lb-ft3 Nm
- Pressure Regulator Screws6 lb-ft8 Nm
- Pump Mounting12 lb-ft16 Nm
Fuel Pressure Regulator6 specs
- Filter Bracket9 lb-ft12 Nm
- Fuel Line18 lb-ft25 Nm
- Fuel Rail Bolts17 lb-ft23 Nm
- Pressure Regulator Screws6 lb-ft8 Nm
- Pump Mounting12 lb-ft16 Nm
- Regulator Mounting Screws4 lb-ft5 Nm
Fuel Pump2 specs
- Fuel Pump Module Lock RingUse special tool28 lb-ft38 Nm
- Tank Strap Bolts26 lb-ft35 Nm
Fuel Pump Module7 specs
- Access Cover Screws3 lb-ft5 Nm
- Filter Bracket9 lb-ft12 Nm
- Fuel Line FittingsUse new O-rings15 lb-ft20 Nm
- Fuel Pump Lock RingLock ring tool28 lb-ft38 Nm
- Hose Clamps2 lb-ft3 Nm
- Pressure Regulator Screws6 lb-ft8 Nm
- Pump Mounting12 lb-ft16 Nm
Fuel Rail6 specs
- Filter Bracket9 lb-ft12 Nm
- Fuel Line FittingsUse new O-rings18 lb-ft25 Nm
- Fuel Rail Bolts9 lb-ft12 Nm
- Hose Clamps2 lb-ft3 Nm
- Pressure Regulator Screws6 lb-ft8 Nm
- Pump Mounting12 lb-ft16 Nm
Fuel Tank7 specs
- Filler Neck Clamp3 lb-ft4 Nm
- Filter Bracket9 lb-ft12 Nm
- Fuel Line FittingsUse new O-rings15 lb-ft20 Nm
- Fuel Rail Bolts17 lb-ft23 Nm
- Pressure Regulator Screws6 lb-ft8 Nm
- Pump Mounting12 lb-ft16 Nm
- Tank Strap Bolts26 lb-ft35 Nm
Fuel Tank Strap5 specs
- Filter Bracket9 lb-ft12 Nm
- Fuel Line FittingsUse new O-rings15 lb-ft20 Nm
- Hose Clamps2 lb-ft3 Nm
- Pressure Regulator Screws6 lb-ft8 Nm
- Pump Mounting12 lb-ft16 Nm
High Pressure Fuel Pump5 specs
- Filter Bracket9 lb-ft12 Nm
- Fuel Line FittingsUse new O-rings18 lb-ft25 Nm
- Hose Clamps2 lb-ft3 Nm
- Pressure Regulator Screws6 lb-ft8 Nm
- Pump Mounting15 lb-ft21 Nm

Electrical

Airbag - Driver5 specs
- Airbag Module BoltsTorx - disconnect battery and wait 2 minutes5 lb-ft7 Nm
- Battery Terminal Bolts6 lb-ft8 Nm
- Connector Screws3 lb-ft4 Nm
- Ground Strap BoltsClean contact surfaces7 lb-ft9 Nm
- Steering Wheel Nut59 lb-ft80 Nm
Airbag - Passenger5 specs
- Airbag Module BoltsTorx - disconnect battery and wait 2 minutes5 lb-ft7 Nm
- Battery Terminal Bolts6 lb-ft8 Nm
- Connector Screws3 lb-ft4 Nm
- Dashboard Fasteners3 lb-ft4 Nm
- Ground Strap BoltsClean contact surfaces7 lb-ft9 Nm
Airbag - Side5 specs
- Battery Terminal Bolts6 lb-ft8 Nm
- Connector Screws3 lb-ft4 Nm
- Ground Strap BoltsClean contact surfaces7 lb-ft9 Nm
- Seat Mounting BoltsSafety critical32 lb-ft43 Nm
- Side Airbag Module BoltsTorx5 lb-ft7 Nm
Airbag Module/Computer5 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
- Ground Strap BoltsClean contact surfaces7 lb-ft9 Nm
- Module Mounting Bolts6 lb-ft8 Nm
- Sensor Mounting Bolts7 lb-ft10 Nm
Alternator4 specs
- Alternator Mounting Bolts37 lb-ft50 Nm
- Alternator Pivot Bolt18 lb-ft25 Nm
- Battery Terminal BoltsDo not overtighten6 lb-ft8 Nm
- Serpentine Belt Tensioner41 lb-ft55 Nm
Alternator Belt5 specs
- Alternator Mounting Bolts40 lb-ft55 Nm
- Alternator Pivot Bolt40 lb-ft55 Nm
- Battery Cable Nut12 lb-ft16 Nm
- Connector Screws3 lb-ft4 Nm
- Ground Strap BoltsClean contact surfaces7 lb-ft10 Nm
Amplifier4 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
- Ground Strap BoltsClean contact surfaces7 lb-ft9 Nm
- Module Mounting Bolts6 lb-ft8 Nm
Antenna2 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
Backup Camera4 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
- Module Mounting Bolts6 lb-ft8 Nm
- Sensor Mounting Bolts7 lb-ft10 Nm
Battery3 specs
- Battery Hold-Down Bolt6 lb-ft8 Nm
- Battery Terminal BoltsDo not overtighten - can crack terminal4 lb-ft6 Nm
- Battery Tray Bolts9 lb-ft12 Nm
Battery Cable - Negative6 specs
- Battery Hold-Down BoltDo not overtighten9 lb-ft12 Nm
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
- Ground Cable Bolt15 lb-ft20 Nm
- Ground Strap BoltsEnsure clean contact9 lb-ft12 Nm
- Sensor Mounting Bolts7 lb-ft10 Nm
Battery Cable - Positive5 specs
- Battery Hold-Down BoltDo not overtighten9 lb-ft12 Nm
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
- Ground Cable Bolt12 lb-ft16 Nm
- Module Mounting Bolts6 lb-ft8 Nm
Battery Cables - Both6 specs
- Battery Hold-Down BoltDo not overtighten9 lb-ft12 Nm
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
- Ground Cable Bolt12 lb-ft16 Nm
- Ground Strap BoltsEnsure clean contact9 lb-ft12 Nm
- Sensor Mounting Bolts7 lb-ft10 Nm
Battery Terminal6 specs
- Battery Hold-Down BoltDo not overtighten9 lb-ft12 Nm
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
- Ground Cable Bolt12 lb-ft16 Nm
- Ground Strap BoltsEnsure clean contact9 lb-ft12 Nm
- Sensor Mounting Bolts7 lb-ft10 Nm
Blower Motor2 specs
- Blower Motor Mounting Screw3 lb-ft4 Nm
- Blower Motor Resistor Screws1.5 lb-ft2 Nm
Blower Motor Control Module3 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
- Module Mounting Bolts6 lb-ft8 Nm
Blower Motor Resistor4 specs
- Battery Terminal Bolts6 lb-ft8 Nm
- Connector Screws3 lb-ft4 Nm
- Ground Strap BoltsClean contact surfaces12 lb-ft16 Nm
- Resistor Screws1.5 lb-ft2 Nm
Clock Spring7 specs
- Airbag Module BoltsTorx - disconnect battery first5 lb-ft7 Nm
- Battery Terminal Bolts6 lb-ft8 Nm
- Clock Spring ScrewsAlign marks before removal3 lb-ft4 Nm
- Connector Screws3 lb-ft4 Nm
- Ground Strap BoltsClean contact surfaces7 lb-ft10 Nm
- Steering Column CoversPlastic clips2 lb-ft3 Nm
- Steering Wheel Nut59 lb-ft80 Nm
Combination Switch4 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
- Module Mounting Bolts6 lb-ft8 Nm
- Sensor Mounting Bolts7 lb-ft10 Nm
Dimmer Switch4 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
- Ground Strap BoltsClean contact surfaces7 lb-ft10 Nm
- Module Mounting Bolts6 lb-ft8 Nm
Door Lock Actuator - Front3 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
- Ground Strap BoltsClean contact surfaces12 lb-ft16 Nm
Door Lock Actuator - Rear3 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
- Ground Strap BoltsClean contact surfaces12 lb-ft16 Nm
Fog Light Assembly2 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
Fog Light Bulb1 spec
- Connector Screws3 lb-ft4 Nm
Fuel Pump Relay6 specs
- Access Cover Screws3 lb-ft5 Nm
- Battery Terminal Bolts6 lb-ft8 Nm
- Connector Screws3 lb-ft4 Nm
- Fuel Pump Lock RingLock ring tool28 lb-ft38 Nm
- Ground Strap BoltsClean contact surfaces7 lb-ft10 Nm
- Relay Socket4 lb-ft5 Nm
Fuse Box - Engine Bay4 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
- Ground Strap BoltsClean contact surfaces7 lb-ft10 Nm
- Module Mounting Bolts6 lb-ft8 Nm
Fuse Box - Interior4 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
- Ground Strap BoltsClean contact surfaces7 lb-ft10 Nm
- Module Mounting Bolts6 lb-ft8 Nm
Headlight Assembly5 specs
- Adjuster Screws2 lb-ft3 Nm
- Battery Terminal Bolts6 lb-ft8 Nm
- Connector Screws3 lb-ft4 Nm
- Ground Strap BoltsClean contact surfaces7 lb-ft10 Nm
- Headlight Assembly Bolts7 lb-ft10 Nm
Headlight Bulb - Single4 specs
- Battery Terminal Bolts6 lb-ft8 Nm
- Bulb Retaining Ring4 lb-ft5 Nm
- Connector Screws3 lb-ft4 Nm
- Ground Strap BoltsClean contact surfaces7 lb-ft9 Nm
Headlight Bulbs - Pair2 specs
- Connector Screws3 lb-ft4 Nm
- Ground Strap BoltsClean contact surfaces7 lb-ft9 Nm
Headlight Switch4 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
- Ground Strap BoltsClean contact surfaces7 lb-ft9 Nm
- Module Mounting Bolts6 lb-ft8 Nm
Heated Seat Module4 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
- Ground Strap BoltsClean contact surfaces7 lb-ft9 Nm
- Module Mounting Bolts6 lb-ft8 Nm
HID Ballast4 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
- Ground Strap BoltsClean contact surfaces7 lb-ft9 Nm
- Module Mounting Bolts6 lb-ft8 Nm
Horn4 specs
- Battery Terminal Bolts6 lb-ft8 Nm
- Connector Screws3 lb-ft4 Nm
- Ground Strap BoltsClean contact surfaces7 lb-ft9 Nm
- Horn Mounting Bolt11 lb-ft15 Nm
Horn Relay3 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
- Ground Strap BoltsClean contact surfaces7 lb-ft9 Nm
Instrument Cluster4 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
- Ground Strap BoltsClean contact surfaces7 lb-ft9 Nm
- Module Mounting Bolts6 lb-ft8 Nm
LED Headlight Module4 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
- Ground Strap BoltsClean contact surfaces7 lb-ft9 Nm
- Module Mounting Bolts6 lb-ft8 Nm
Main Relay4 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
- Ground Strap BoltsClean contact surfaces7 lb-ft9 Nm
- Module Mounting Bolts6 lb-ft8 Nm
Power Antenna Motor3 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
- Ground Strap BoltsClean contact surfaces12 lb-ft16 Nm
Power Mirror Motor2 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
Power Seat Motor4 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
- Ground Strap BoltsClean contact surfaces12 lb-ft16 Nm
- Module Mounting Bolts6 lb-ft8 Nm
Power Window Motor - Front4 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
- Ground Strap BoltsClean contact surfaces7 lb-ft9 Nm
- Module Mounting Bolts6 lb-ft8 Nm
Power Window Motor - Rear4 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
- Ground Strap BoltsClean contact surfaces7 lb-ft9 Nm
- Module Mounting Bolts6 lb-ft8 Nm
Power Window Regulator - Front4 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
- Ground Strap BoltsClean contact surfaces7 lb-ft9 Nm
- Module Mounting Bolts6 lb-ft8 Nm
Power Window Regulator - Rear3 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
- Ground Strap BoltsClean contact surfaces7 lb-ft9 Nm
Radio/Head Unit4 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
- Ground Strap BoltsClean contact surfaces7 lb-ft9 Nm
- Module Mounting Bolts6 lb-ft8 Nm
Relay - Generic4 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
- Ground Strap BoltsClean contact surfaces7 lb-ft10 Nm
- Module Mounting Bolts6 lb-ft8 Nm
Seat Heater Element4 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
- Module Mounting Bolts6 lb-ft8 Nm
- Sensor Mounting Bolts7 lb-ft10 Nm
Side Mirror Assembly2 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
Speaker - Dash3 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
- Sensor Mounting Bolts7 lb-ft10 Nm
Speaker - Door3 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
- Ground Strap BoltsClean contact surfaces12 lb-ft16 Nm
Speedometer5 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
- Ground Strap BoltsClean contact surfaces12 lb-ft16 Nm
- Module Mounting Bolts6 lb-ft8 Nm
- Sensor Mounting Bolts7 lb-ft10 Nm
Starter3 specs
- Heat Shield BoltsIf equipped7 lb-ft10 Nm
- Starter Mounting BoltLong bolt may need extension30 lb-ft40 Nm
- Starter Solenoid NutFor B+ cable9 lb-ft12 Nm
Starter Solenoid5 specs
- Battery Cable Nut12 lb-ft16 Nm
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
- Ground Strap BoltsClean contact surfaces12 lb-ft16 Nm
- Starter Mounting Bolt30 lb-ft40 Nm
Subwoofer4 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
- Ground Strap BoltsClean contact surfaces7 lb-ft9 Nm
- Module Mounting Bolts6 lb-ft8 Nm
Sunroof Motor3 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
- Module Mounting Bolts6 lb-ft8 Nm
Sunroof Switch3 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
- Ground Strap BoltsClean contact surfaces12 lb-ft16 Nm
Tail Light Assembly5 specs
- Battery Terminal Bolts6 lb-ft8 Nm
- Connector Screws3 lb-ft4 Nm
- Ground Strap BoltsClean contact surfaces7 lb-ft10 Nm
- Lens Screws1.5 lb-ft2 Nm
- Tail Light Bolts6 lb-ft8 Nm
Tail Light Bulb2 specs
- Connector Screws3 lb-ft4 Nm
- Ground Strap BoltsClean contact surfaces12 lb-ft16 Nm
Third Brake Light4 specs
- Battery Terminal BoltsDo not overtighten. Verify sequence with the service manual4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
- Module Mounting BoltsVerify sequence with the service manual6 lb-ft8 Nm
- Sensor Mounting BoltsVerify sequence with the service manual7 lb-ft10 Nm
Trunk/Liftgate Actuator3 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
- Ground Strap BoltsClean contact surfaces12 lb-ft16 Nm
Turn Signal Bulb - Front2 specs
- Connector Screws3 lb-ft4 Nm
- Ground Strap BoltsClean contact surfaces12 lb-ft16 Nm
Turn Signal Bulb - Rear2 specs
- Connector Screws3 lb-ft4 Nm
- Ground Strap BoltsClean contact surfaces12 lb-ft16 Nm
Turn Signal Switch5 specs
- Battery Terminal Bolts6 lb-ft8 Nm
- Connector Screws3 lb-ft4 Nm
- Ground Strap BoltsClean contact surfaces12 lb-ft16 Nm
- Steering Column Covers1.5 lb-ft2 Nm
- Switch Mounting Screws2 lb-ft3 Nm
Voltage Regulator3 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
- Module Mounting Bolts6 lb-ft8 Nm
Washer Pump2 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
Washer Reservoir4 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
- Ground Strap BoltsClean contact surfaces7 lb-ft9 Nm
- Sensor Mounting Bolts7 lb-ft10 Nm
Window Motor and Regulator - Front4 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
- Ground Strap BoltsClean contact surfaces7 lb-ft9 Nm
- Module Mounting Bolts6 lb-ft8 Nm
Window Motor and Regulator - Rear4 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
- Ground Strap BoltsClean contact surfaces7 lb-ft9 Nm
- Module Mounting Bolts6 lb-ft8 Nm
Wiper Linkage7 specs
- Battery Terminal Bolts6 lb-ft8 Nm
- Connector Screws3 lb-ft4 Nm
- Ground Strap BoltsEnsure clean contact9 lb-ft12 Nm
- Linkage Pivot Nuts9 lb-ft12 Nm
- Module Mounting Bolts6 lb-ft8 Nm
- Motor Mounting Bolts7 lb-ft10 Nm
- Sensor Mounting Bolts7 lb-ft10 Nm
Wiper Motor - Front3 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
- Module Mounting Bolts6 lb-ft8 Nm
Wiper Motor - Rear3 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
- Ground Strap BoltsClean contact surfaces12 lb-ft16 Nm
Wiper Switch3 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
- Ground Strap BoltsClean contact surfaces12 lb-ft16 Nm

Suspension

Ball Joint - Lower7 specs
- Control Arm BoltsTorque with vehicle weight on wheels122 lb-ft165 Nm
- Lower Ball Joint NutUse new cotter pin75 lb-ft102 Nm
- Pinch BoltNew bolt52 lb-ft70 Nm
- Strut Bolts98 lb-ft133 Nm
- Sway Bar Link52 lb-ft71 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug NutsTorque in star pattern133 lb-ft180 Nm
Ball Joint - Upper7 specs
- Control Arm BoltsTorque with vehicle weight on wheels103 lb-ft140 Nm
- Pinch BoltNew bolt52 lb-ft70 Nm
- Strut Bolts98 lb-ft133 Nm
- Sway Bar Link52 lb-ft71 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Upper Ball Joint NutUse new cotter pin63 lb-ft85 Nm
- Wheel Lug NutsTorque in star pattern133 lb-ft180 Nm
Ball Joints - Upper and Lower9 specs
- Control Arm BoltsTorque with vehicle weight on wheels122 lb-ft165 Nm
- Lower Ball Joint NutUse new cotter pin75 lb-ft102 Nm
- Pinch BoltNew bolt52 lb-ft70 Nm
- Strut Bolts98 lb-ft133 Nm
- Strut Tower Nuts37 lb-ft50 Nm
- Sway Bar Link52 lb-ft71 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Upper Ball Joint NutUse new cotter pin75.2 lb-ft102 Nm
- Wheel Lug NutsTorque in star pattern133 lb-ft180 Nm
Coil Spring - Front6 specs
- Control Arm BoltsTorque with vehicle weight on wheels122 lb-ft165 Nm
- Strut Bolts74 lb-ft100 Nm
- Strut Tower Nuts37 lb-ft50 Nm
- Sway Bar Link52 lb-ft71 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug NutsTorque in star pattern133 lb-ft180 Nm
Coil Spring - Rear4 specs
- Control Arm BoltsTorque with vehicle weight on wheels122 lb-ft165 Nm
- Sway Bar Link52 lb-ft71 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug NutsTorque in star pattern133 lb-ft180 Nm
Coil Springs - Front Pair6 specs
- Control Arm BoltsTorque with vehicle weight on wheels122 lb-ft165 Nm
- Strut Bolts74 lb-ft100 Nm
- Strut Tower Nuts24 lb-ft33 Nm
- Sway Bar Link52 lb-ft71 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug NutsTorque in star pattern133 lb-ft180 Nm
Coil Springs - Rear Pair4 specs
- Control Arm BoltsTorque with vehicle weight on wheels122 lb-ft165 Nm
- Sway Bar Link52 lb-ft71 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug NutsTorque in star pattern133 lb-ft180 Nm
Control Arm Bushing - Front Lower7 specs
- Control Arm BoltsTorque with vehicle weight on wheels122 lb-ft165 Nm
- Lower Ball Joint NutUse new cotter pin96 lb-ft130 Nm
- Strut Bolts74 lb-ft100 Nm
- Strut Tower Nuts24 lb-ft33 Nm
- Sway Bar Link52 lb-ft71 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug NutsTorque in star pattern133 lb-ft180 Nm
Control Arm Bushing - Front Upper7 specs
- Control Arm BoltsTorque with vehicle weight on wheels122 lb-ft165 Nm
- Strut Bolts74 lb-ft100 Nm
- Strut Tower Nuts24 lb-ft33 Nm
- Sway Bar Link52 lb-ft71 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Upper Ball Joint NutUse new cotter pin75 lb-ft102 Nm
- Wheel Lug NutsTorque in star pattern133 lb-ft180 Nm
Control Arm Bushing - Rear4 specs
- Control Arm BoltsTorque with vehicle weight on wheels122 lb-ft165 Nm
- Sway Bar Link52 lb-ft71 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug NutsTorque in star pattern133 lb-ft180 Nm
Front Struts - Pair9 specs
- Control Arm BoltsTorque with vehicle weight on wheels122 lb-ft165 Nm
- Strut Bolts52 lb-ft70 Nm
- Strut Mount to Body NutsHold strut rod while torquing30 lb-ft40 Nm
- Strut Piston Rod NutUse impact or hold rod with Allen key44 lb-ft60 Nm
- Strut to Knuckle BoltsMay be cam bolts for alignment. Mark position before removal74 lb-ft100 Nm
- Strut Tower Nuts30 lb-ft40 Nm
- Sway Bar Link44 lb-ft60 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug NutsTorque in star pattern133 lb-ft180 Nm
Front Suspension Rebuild5 specs
- Ball Joint Pinch BoltUse new bolt if locknut style37 lb-ft50 Nm
- Lower Control Arm BoltsTorque at ride height140 lb-ft190 Nm
- Strut Top Mount Nuts18 lb-ft25 Nm
- Sway Bar End Link Nuts44 lb-ft60 Nm
- Upper Control Arm BoltsTorque at ride height103 lb-ft140 Nm
Knuckle/Spindle - Front8 specs
- Control Arm BoltsTorque with vehicle weight on wheels122 lb-ft165 Nm
- Lower Ball Joint NutUse new cotter pin75 lb-ft102 Nm
- Strut Bolts74 lb-ft100 Nm
- Strut Tower Nuts24 lb-ft33 Nm
- Sway Bar Link52 lb-ft71 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Upper Ball Joint NutUse new cotter pin75.2 lb-ft102 Nm
- Wheel Lug NutsTorque in star pattern133 lb-ft180 Nm
Lateral Arm6 specs
- Control Arm BoltsTorque with vehicle weight on wheels122 lb-ft165 Nm
- Strut Bolts98 lb-ft133 Nm
- Strut Tower Nuts37 lb-ft50 Nm
- Sway Bar Link52 lb-ft71 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug NutsTorque in star pattern133 lb-ft180 Nm
Lower Control Arm - Front8 specs
- Control Arm BoltsTorque with vehicle weight on wheels122 lb-ft165 Nm
- Lower Ball Joint NutUse new cotter pin114 lb-ft155 Nm
- Lower Control Arm Ball Joint NutUse new nut114 lb-ft155 Nm
- Lower Control Arm Frame BoltsTORQUE AT RIDE HEIGHT. Use new bolts if TTY140 lb-ft190 Nm
- Strut Bolts98 lb-ft133 Nm
- Sway Bar Link52 lb-ft71 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug NutsTorque in star pattern133 lb-ft180 Nm
Lower Control Arm - Rear4 specs
- Control Arm BoltsTorque with vehicle weight on wheels122 lb-ft165 Nm
- Sway Bar Link52 lb-ft71 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug NutsTorque in star pattern133 lb-ft180 Nm
Radius Arm6 specs
- Control Arm BoltsTorque with vehicle weight on wheels122 lb-ft165 Nm
- Strut Bolts98 lb-ft133 Nm
- Strut Tower Nuts37 lb-ft50 Nm
- Sway Bar Link52 lb-ft71 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug NutsTorque in star pattern133 lb-ft180 Nm
Radius Arm Bushing6 specs
- Control Arm BoltsTorque with vehicle weight on wheels122 lb-ft165 Nm
- Strut Bolts98 lb-ft133 Nm
- Strut Tower Nuts37 lb-ft50 Nm
- Sway Bar Link52 lb-ft71 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug NutsTorque in star pattern133 lb-ft180 Nm
Rear Shocks - Pair4 specs
- Control Arm BoltsTorque with vehicle weight on wheels122 lb-ft165 Nm
- Sway Bar Link52 lb-ft71 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug NutsTorque in star pattern133 lb-ft180 Nm
Rear Suspension Service4 specs
- Lower Control Arm BoltsTorque at ride height133 lb-ft180 Nm
- Shock Lower Bolt52 lb-ft70 Nm
- Sway Bar End Link Nuts37 lb-ft50 Nm
- Trailing Arm BoltsTorque at ride height140 lb-ft190 Nm
Shock Absorber Replacement2 specs
- Lower Mount Bolt66 lb-ft90 Nm
- Upper Mount NutUse new self-locking nut41 lb-ft55 Nm
Strut Bearing6 specs
- Strut Bolts98 lb-ft133 Nm
- Strut to Knuckle Bolts104 lb-ft140 Nm
- Strut Tower Nuts37 lb-ft50 Nm
- Sway Bar Link52 lb-ft71 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug NutsTorque in star pattern133 lb-ft180 Nm
Strut Mount - Front6 specs
- Strut Bolts98 lb-ft133 Nm
- Strut to Knuckle Bolts104 lb-ft140 Nm
- Strut Tower Nuts37 lb-ft50 Nm
- Sway Bar Link52 lb-ft71 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug NutsTorque in star pattern133 lb-ft180 Nm
Subframe6 specs
- Control Arm BoltsTorque with vehicle weight on wheels122 lb-ft165 Nm
- Strut Bolts98 lb-ft133 Nm
- Strut Tower Nuts37 lb-ft50 Nm
- Sway Bar Link52 lb-ft71 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug NutsTorque in star pattern133 lb-ft180 Nm
Subframe Bushing6 specs
- Control Arm BoltsTorque with vehicle weight on wheels122 lb-ft165 Nm
- Strut Bolts98 lb-ft133 Nm
- Strut Tower Nuts37 lb-ft50 Nm
- Sway Bar Link52 lb-ft71 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug NutsTorque in star pattern133 lb-ft180 Nm
Sway Bar - Front6 specs
- Control Arm BoltsTorque with vehicle weight on wheels122 lb-ft165 Nm
- Strut Bolts98 lb-ft133 Nm
- Sway Bar Bracket Bolts40 lb-ft55 Nm
- Sway Bar Link52 lb-ft71 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug NutsTorque in star pattern133 lb-ft180 Nm
Sway Bar - Rear5 specs
- Control Arm BoltsTorque with vehicle weight on wheels122 lb-ft165 Nm
- Sway Bar Bracket Bolts40 lb-ft55 Nm
- Sway Bar Link52 lb-ft71 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug NutsTorque in star pattern133 lb-ft180 Nm
Sway Bar Bushing - Front6 specs
- Control Arm BoltsTorque with vehicle weight on wheels122 lb-ft165 Nm
- Strut Bolts98 lb-ft133 Nm
- Sway Bar Bracket Bolts40 lb-ft55 Nm
- Sway Bar Link52 lb-ft71 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug NutsTorque in star pattern133 lb-ft180 Nm
Sway Bar Bushing - Rear5 specs
- Control Arm BoltsTorque with vehicle weight on wheels122 lb-ft165 Nm
- Sway Bar Bracket Bolts40 lb-ft55 Nm
- Sway Bar Link52 lb-ft71 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug NutsTorque in star pattern133 lb-ft180 Nm
Sway Bar Link - Front6 specs
- Control Arm BoltsTorque with vehicle weight on wheels122 lb-ft165 Nm
- Strut Bolts98 lb-ft133 Nm
- Sway Bar Bracket Bolts40 lb-ft55 Nm
- Sway Bar Link52 lb-ft71 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug NutsTorque in star pattern133 lb-ft180 Nm
Sway Bar Link - Rear5 specs
- Control Arm BoltsTorque with vehicle weight on wheels122 lb-ft165 Nm
- Sway Bar Bracket Bolts40 lb-ft55 Nm
- Sway Bar Link52 lb-ft71 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug NutsTorque in star pattern133 lb-ft180 Nm
Sway Bar Links - Front Pair6 specs
- Control Arm BoltsTorque with vehicle weight on wheels122 lb-ft165 Nm
- Strut Bolts98 lb-ft133 Nm
- Sway Bar Bracket Bolts40 lb-ft55 Nm
- Sway Bar Link52 lb-ft71 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug NutsTorque in star pattern133 lb-ft180 Nm
Torsion Bar6 specs
- Control Arm BoltsTorque with vehicle weight on wheels122 lb-ft165 Nm
- Strut Bolts98 lb-ft133 Nm
- Strut Tower Nuts37 lb-ft50 Nm
- Sway Bar Link52 lb-ft71 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug NutsTorque in star pattern133 lb-ft180 Nm
Torsion Bar Adjustment4 specs
- Control Arm BoltsTorque with vehicle weight on wheels122 lb-ft165 Nm
- Strut Bolts98 lb-ft133 Nm
- Sway Bar Link52 lb-ft71 Nm
- Wheel Lug NutsTorque in star pattern133 lb-ft180 Nm
Trailing Arm5 specs
- Control Arm BoltsTorque with vehicle weight on wheels122 lb-ft165 Nm
- Strut Bolts98 lb-ft133 Nm
- Sway Bar Link52 lb-ft71 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug NutsTorque in star pattern133 lb-ft180 Nm
Trailing Arm Bushing5 specs
- Control Arm BoltsTorque with vehicle weight on wheels122 lb-ft165 Nm
- Strut Bolts98 lb-ft133 Nm
- Sway Bar Link52 lb-ft71 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug NutsTorque in star pattern133 lb-ft180 Nm
Upper Control Arm - Front7 specs
- Control Arm BoltsTorque with vehicle weight on wheels122 lb-ft165 Nm
- Strut Bolts98 lb-ft133 Nm
- Strut Tower Nuts30 lb-ft40 Nm
- Sway Bar Link52 lb-ft71 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Upper Ball Joint NutUse new cotter pin75 lb-ft102 Nm
- Wheel Lug NutsTorque in star pattern133 lb-ft180 Nm
Upper Control Arm - Rear3 specs
- Control Arm BoltsTorque with vehicle weight on wheels122 lb-ft165 Nm
- Sway Bar Link52 lb-ft71 Nm
- Wheel Lug NutsTorque in star pattern133 lb-ft180 Nm

Steering

Power Steering Fluid Flush7 specs
- Coupling Bolt29 lb-ft39 Nm
- Power Steering Line FittingsUse new O-rings30 lb-ft40 Nm
- Steering Rack Bolts74 lb-ft100 Nm
- Tie Rod End Castle NutUse new cotter pin41 lb-ft55 Nm
- Tie Rod End NutUse new cotter pin63 lb-ft85 Nm
- Tie Rod Nut63 lb-ft85 Nm
- Wheel Lug Nuts133 lb-ft180 Nm
Power Steering Hose - High Pressure7 specs
- Coupling Bolt29 lb-ft39 Nm
- Power Steering Line FittingsUse new O-rings30 lb-ft40 Nm
- Steering Rack Bolts52 lb-ft70 Nm
- Tie Rod End Castle NutUse new cotter pin41 lb-ft55 Nm
- Tie Rod End NutUse new cotter pin46 lb-ft62 Nm
- Tie Rod Nut46 lb-ft62 Nm
- Wheel Lug Nuts133 lb-ft180 Nm
Power Steering Hose - Return7 specs
- Coupling Bolt22 lb-ft30 Nm
- Power Steering Line FittingsUse new O-rings22 lb-ft30 Nm
- Steering Rack Bolts52 lb-ft70 Nm
- Tie Rod End Castle NutUse new cotter pin41 lb-ft55 Nm
- Tie Rod End NutUse new cotter pin46 lb-ft62 Nm
- Tie Rod Nut46 lb-ft62 Nm
- Wheel Lug Nuts133 lb-ft180 Nm
Power Steering Pump8 specs
- High Pressure Hose FittingUse new O-rings32 lb-ft43 Nm
- Power Steering Pump Bolts15 lb-ft20 Nm
- Pressure Line FittingUse new O-rings32 lb-ft43 Nm
- Pulley NutHold pulley with pin spanner52 lb-ft70 Nm
- Pump Mounting Bolts18 lb-ft25 Nm
- Return Hose Clamp2 lb-ft3 Nm
- Return Line Clamp3 lb-ft4 Nm
- Serpentine Belt Tensioner41 lb-ft55 Nm
Power Steering Pump Pulley8 specs
- Coupling Bolt29 lb-ft39 Nm
- Power Steering Line FittingsUse new O-rings. Verify sequence with the service manual30 lb-ft40 Nm
- Pressure Line FittingNew O-ring29 lb-ft39 Nm
- Pump Mounting Bolts15 lb-ft20 Nm
- Steering Rack BoltsVerify sequence with the service manual74 lb-ft100 Nm
- Tie Rod End NutUse new cotter pin63 lb-ft85 Nm
- Tie Rod Nut63 lb-ft85 Nm
- Wheel Lug Nuts133 lb-ft180 Nm
Power Steering Reservoir7 specs
- Coupling Bolt22 lb-ft30 Nm
- Power Steering Line FittingsUse new O-rings22 lb-ft30 Nm
- Steering Rack Bolts52 lb-ft70 Nm
- Tie Rod End Castle NutUse new cotter pin41 lb-ft55 Nm
- Tie Rod End NutUse new cotter pin46 lb-ft62 Nm
- Tie Rod Nut46 lb-ft62 Nm
- Wheel Lug Nuts133 lb-ft180 Nm
Rack and Pinion Boots7 specs
- Coupling Bolt22 lb-ft30 Nm
- Power Steering Line FittingsUse new O-rings22 lb-ft30 Nm
- Steering Rack Bolts52 lb-ft70 Nm
- Tie Rod End Castle NutUse new cotter pin41 lb-ft55 Nm
- Tie Rod End NutUse new cotter pin46 lb-ft62 Nm
- Tie Rod Nut46 lb-ft62 Nm
- Wheel Lug Nuts133 lb-ft180 Nm
Steering Angle Sensor4 specs
- Coupling Bolt18 lb-ft25 Nm
- Tie Rod End NutUse new cotter pin46 lb-ft62 Nm
- Tie Rod Nut46 lb-ft62 Nm
- Wheel Lug Nuts133 lb-ft180 Nm
Steering Column9 specs
- Coupling Bolt18 lb-ft25 Nm
- Ignition Switch BoltsVerify sequence with the service manual4 lb-ft5 Nm
- Pinch BoltVerify sequence with the service manual18 lb-ft25 Nm
- Power Steering Line FittingsUse new O-rings29 lb-ft39 Nm
- Steering Column BoltsVerify sequence with the service manual15 lb-ft20 Nm
- Steering Rack Bolts86 lb-ft117 Nm
- Tie Rod End NutUse new cotter pin46 lb-ft62 Nm
- Tie Rod Nut46 lb-ft62 Nm
- Wheel Lug Nuts133 lb-ft180 Nm
Steering Coupler5 specs
- Coupling Bolt18 lb-ft25 Nm
- Steering Rack BoltsVerify sequence with the service manual74 lb-ft100 Nm
- Tie Rod End NutUse new cotter pin46 lb-ft62 Nm
- Tie Rod Nut46 lb-ft62 Nm
- Wheel Lug Nuts133 lb-ft180 Nm
Steering Damper4 specs
- Coupling Bolt29 lb-ft39 Nm
- Tie Rod End NutUse new cotter pin46 lb-ft62 Nm
- Tie Rod Nut46 lb-ft62 Nm
- Wheel Lug Nuts133 lb-ft180 Nm
Steering Shaft - Intermediate5 specs
- Coupling Bolt18 lb-ft25 Nm
- Steering Rack BoltsVerify sequence with the service manual74 lb-ft100 Nm
- Tie Rod End NutUse new cotter pin46 lb-ft62 Nm
- Tie Rod Nut46 lb-ft62 Nm
- Wheel Lug Nuts133 lb-ft180 Nm
Steering Shaft - Upper4 specs
- Coupling Bolt18 lb-ft25 Nm
- Tie Rod End NutUse new cotter pin46 lb-ft62 Nm
- Tie Rod Nut46 lb-ft62 Nm
- Wheel Lug Nuts133 lb-ft180 Nm
Steering Wheel8 specs
- Airbag Module BoltsTorx - usually T30. Verify sequence with the service manual5 lb-ft7 Nm
- Coupling Bolt29 lb-ft39 Nm
- Power Steering Line FittingsUse new O-rings29 lb-ft39 Nm
- Steering Rack Bolts86 lb-ft117 Nm
- Steering Wheel NutVerify sequence with the service manual59 lb-ft80 Nm
- Tie Rod End NutUse new cotter pin46 lb-ft62 Nm
- Tie Rod Nut46 lb-ft62 Nm
- Wheel Lug Nuts133 lb-ft180 Nm
Tie Rod Assembly7 specs
- Coupling Bolt29 lb-ft39 Nm
- Steering Rack Bolts74 lb-ft100 Nm
- Tie Rod End Castle NutUse new cotter pin41 lb-ft55 Nm
- Tie Rod End NutUse new cotter pin59 lb-ft80 Nm
- Tie Rod Lock NutAfter alignment30 lb-ft40 Nm
- Tie Rod Nut59 lb-ft80 Nm
- Wheel Lug Nuts133 lb-ft180 Nm
Tie Rod End - Inner7 specs
- Coupling Bolt29 lb-ft39 Nm
- Steering Rack Bolts74 lb-ft100 Nm
- Tie Rod End Castle NutUse new cotter pin41 lb-ft55 Nm
- Tie Rod End NutUse new cotter pin59 lb-ft80 Nm
- Tie Rod Lock NutAfter alignment30 lb-ft40 Nm
- Tie Rod Nut46 lb-ft62 Nm
- Wheel Lug Nuts133 lb-ft180 Nm
Tie Rod End - Outer7 specs
- Coupling Bolt29 lb-ft39 Nm
- Steering Rack Bolts74 lb-ft100 Nm
- Tie Rod End Castle NutUse new cotter pin41 lb-ft55 Nm
- Tie Rod End NutUse new cotter pin59 lb-ft80 Nm
- Tie Rod Lock NutAfter alignment30 lb-ft40 Nm
- Tie Rod Nut59 lb-ft80 Nm
- Wheel Lug Nuts133 lb-ft180 Nm
Tie Rods - Both Sides8 specs
- Coupling Bolt29 lb-ft39 Nm
- Power Steering Line FittingsUse new O-rings32 lb-ft43 Nm
- Steering Rack Bolts59 lb-ft80 Nm
- Tie Rod End Castle NutUse new cotter pin48 lb-ft65 Nm
- Tie Rod End NutUse new cotter pin46 lb-ft62 Nm
- Tie Rod Lock NutAfter alignment33 lb-ft45 Nm
- Tie Rod Nut46 lb-ft62 Nm
- Wheel Lug Nuts133 lb-ft180 Nm

Drivetrain

4WD Actuator7 specs
- Axle NutUse new cotter pin or stake nut221 lb-ft300 Nm
- CV Bolts52 lb-ft70 Nm
- CV Joint Bolts52 lb-ft71 Nm
- Differential Cover Bolts26 lb-ft35 Nm
- Driveshaft Bolts44 lb-ft60 Nm
- Driveshaft U-Joint StrapsTighten evenly15 lb-ft20 Nm
- Wheel Lug NutsTorque in star pattern133 lb-ft180 Nm
Axle Seal - Front7 specs
- Axle NutUse new cotter pin or stake nut184 lb-ft250 Nm
- CV Bolts52 lb-ft70 Nm
- CV Joint Bolts52 lb-ft71 Nm
- Differential Cover Bolts26 lb-ft35 Nm
- Driveshaft Bolts44 lb-ft60 Nm
- Driveshaft U-Joint StrapsTighten evenly15 lb-ft20 Nm
- Wheel Lug NutsTorque in star pattern133 lb-ft180 Nm
Axle Seal - Rear7 specs
- Axle NutUse new cotter pin or stake nut184 lb-ft250 Nm
- CV Bolts52 lb-ft70 Nm
- CV Joint Bolts52 lb-ft71 Nm
- Differential Cover Bolts26 lb-ft35 Nm
- Driveshaft Bolts44 lb-ft60 Nm
- Driveshaft U-Joint StrapsTighten evenly15 lb-ft20 Nm
- Wheel Lug NutsTorque in star pattern133 lb-ft180 Nm
Axle Shaft - Rear7 specs
- Axle NutUse new cotter pin or stake nut184 lb-ft250 Nm
- CV Bolts52 lb-ft70 Nm
- CV Joint Bolts52 lb-ft71 Nm
- Differential Cover Bolts26 lb-ft35 Nm
- Driveshaft Bolts44 lb-ft60 Nm
- Driveshaft U-Joint StrapsTighten evenly15 lb-ft20 Nm
- Wheel Lug NutsTorque in star pattern133 lb-ft180 Nm
CV Axle - Front9 specs
- Axle NutUse new nut, stake after207 lb-ft281 Nm
- Ball Joint Pinch Bolt41 lb-ft55 Nm
- CV Axle NutUse new cotter pin or stake nut184 lb-ft250 Nm
- CV Bolts52 lb-ft70 Nm
- CV Joint Bolts52 lb-ft71 Nm
- Differential Cover BoltsApply RTV sealant29 lb-ft39 Nm
- Driveshaft Bolts44 lb-ft60 Nm
- Lower Ball Joint Nut86 lb-ft117 Nm
- Wheel Lug Nuts133 lb-ft180 Nm
CV Axle - Rear6 specs
- Axle NutUse new nut, stake after207 lb-ft281 Nm
- CV Bolts52 lb-ft70 Nm
- CV Joint Bolts52 lb-ft71 Nm
- Differential Cover BoltsApply RTV sealant29 lb-ft39 Nm
- Driveshaft Bolts44 lb-ft60 Nm
- Wheel Lug Nuts133 lb-ft180 Nm
CV Axles - Front Pair7 specs
- Axle NutUse new cotter pin or stake nut184 lb-ft250 Nm
- CV Bolts52 lb-ft70 Nm
- CV Joint Bolts52 lb-ft71 Nm
- Driveshaft Bolts44 lb-ft60 Nm
- Driveshaft U-Joint StrapsTighten evenly15 lb-ft20 Nm
- Lower Ball Joint Nut86 lb-ft117 Nm
- Wheel Lug NutsTorque in star pattern133 lb-ft180 Nm
CV Boot - Inner6 specs
- Axle NutUse new cotter pin or stake nut184 lb-ft250 Nm
- CV Bolts52 lb-ft70 Nm
- CV Joint Bolts52 lb-ft71 Nm
- Driveshaft Bolts44 lb-ft60 Nm
- Driveshaft U-Joint StrapsTighten evenly15 lb-ft20 Nm
- Wheel Lug NutsTorque in star pattern133 lb-ft180 Nm
CV Boot - Outer6 specs
- Axle NutUse new cotter pin or stake nut184 lb-ft250 Nm
- CV Bolts52 lb-ft70 Nm
- CV Joint Bolts52 lb-ft71 Nm
- Driveshaft Bolts44 lb-ft60 Nm
- Driveshaft U-Joint StrapsTighten evenly15 lb-ft20 Nm
- Wheel Lug NutsTorque in star pattern133 lb-ft180 Nm
Differential Cover Gasket5 specs
- CV Bolts52 lb-ft70 Nm
- CV Joint Bolts52 lb-ft71 Nm
- Differential Cover Bolts26 lb-ft35 Nm
- Driveshaft Bolts52 lb-ft70 Nm
- Driveshaft U-Joint StrapsTighten evenly15 lb-ft20 Nm
Differential Fluid Change - Front5 specs
- CV Bolts52 lb-ft70 Nm
- CV Joint Bolts52 lb-ft71 Nm
- Differential Cover Bolts26 lb-ft35 Nm
- Driveshaft Bolts52 lb-ft70 Nm
- Driveshaft U-Joint StrapsTighten evenly15 lb-ft20 Nm
Differential Fluid Change - Rear6 specs
- Axle NutUse new cotter pin or stake nut184 lb-ft250 Nm
- CV Bolts52 lb-ft70 Nm
- CV Joint Bolts52 lb-ft71 Nm
- Differential Cover Bolts26 lb-ft35 Nm
- Driveshaft Bolts52 lb-ft70 Nm
- Driveshaft U-Joint StrapsTighten evenly15 lb-ft20 Nm
Differential Pinion Seal5 specs
- CV Bolts52 lb-ft70 Nm
- CV Joint Bolts52 lb-ft71 Nm
- Differential Cover Bolts26 lb-ft35 Nm
- Driveshaft Bolts52 lb-ft70 Nm
- Driveshaft U-Joint StrapsTighten evenly15 lb-ft20 Nm
Differential Rebuild - Front9 specs
- Axle NutUse new cotter pin or stake nut184 lb-ft250 Nm
- CV Bolts52 lb-ft70 Nm
- CV Joint Bolts52 lb-ft71 Nm
- Differential Cover Bolts26 lb-ft35 Nm
- Drain PlugNew washer35 lb-ft47 Nm
- Driveshaft Bolts52 lb-ft70 Nm
- Driveshaft U-Joint StrapsTighten evenly15 lb-ft20 Nm
- Fill Plug35 lb-ft47 Nm
- Wheel Lug NutsTorque in star pattern133 lb-ft180 Nm
Differential Rebuild - Rear9 specs
- Axle NutUse new cotter pin or stake nut184 lb-ft250 Nm
- CV Bolts52 lb-ft70 Nm
- CV Joint Bolts52 lb-ft71 Nm
- Differential Cover Bolts26 lb-ft35 Nm
- Drain PlugNew washer35 lb-ft47 Nm
- Driveshaft Bolts52 lb-ft70 Nm
- Driveshaft U-Joint StrapsTighten evenly15 lb-ft20 Nm
- Fill Plug35 lb-ft47 Nm
- Wheel Lug NutsTorque in star pattern133 lb-ft180 Nm
Driveshaft - Front3 specs
- Center Support Bearing Bracket Bolts37 lb-ft50 Nm
- Driveshaft Flange Bolts (CV/U-Joint)Use new bolts if torque-to-yield44 lb-ft60 Nm
- Transfer Case Output Yoke NutIf accessible133 lb-ft180 Nm
Driveshaft - Rear3 specs
- Differential Pinion Yoke NutUse new nut, set pinion preload184 lb-ft250 Nm
- Driveshaft Flange Bolts44 lb-ft60 Nm
- U-Joint Strap BoltsApply threadlocker26 lb-ft35 Nm
Driveshaft Center Support Bearing2 specs
- Center Support Bearing Bracket Bolts37 lb-ft50 Nm
- Driveshaft Flange Bolts55 lb-ft75 Nm
Front Differential7 specs
- Axle NutUse new cotter pin or stake nut184 lb-ft250 Nm
- CV Bolts52 lb-ft70 Nm
- CV Joint Bolts44 lb-ft60 Nm
- Differential Cover Bolts26 lb-ft35 Nm
- Driveshaft Bolts44 lb-ft60 Nm
- Driveshaft U-Joint StrapsTighten evenly15 lb-ft20 Nm
- Wheel Lug NutsTorque in star pattern133 lb-ft180 Nm
Limited Slip Clutch Pack7 specs
- Axle NutUse new cotter pin or stake nut184 lb-ft250 Nm
- CV Bolts52 lb-ft70 Nm
- CV Joint Bolts52 lb-ft71 Nm
- Differential Cover Bolts26 lb-ft35 Nm
- Driveshaft Bolts63 lb-ft85 Nm
- Driveshaft U-Joint StrapsTighten evenly15 lb-ft20 Nm
- Wheel Lug NutsTorque in star pattern133 lb-ft180 Nm
Rear Differential7 specs
- Axle NutUse new cotter pin or stake nut184 lb-ft250 Nm
- CV Bolts52 lb-ft70 Nm
- CV Joint Bolts52 lb-ft71 Nm
- Differential Cover Bolts26 lb-ft35 Nm
- Driveshaft Bolts63 lb-ft85 Nm
- Driveshaft U-Joint StrapsTighten evenly15 lb-ft20 Nm
- Wheel Lug NutsTorque in star pattern133 lb-ft180 Nm
Ring and Pinion7 specs
- Axle NutUse new cotter pin or stake nut184 lb-ft250 Nm
- CV Bolts52 lb-ft70 Nm
- CV Joint Bolts52 lb-ft71 Nm
- Differential Cover Bolts26 lb-ft35 Nm
- Driveshaft Bolts63 lb-ft85 Nm
- Driveshaft U-Joint StrapsTighten evenly15 lb-ft20 Nm
- Wheel Lug NutsTorque in star pattern133 lb-ft180 Nm
Transfer Case8 specs
- Axle NutUse new nut, stake after207 lb-ft281 Nm
- CV Bolts52 lb-ft70 Nm
- CV Joint Bolts52 lb-ft71 Nm
- Differential Cover BoltsApply RTV sealant29 lb-ft39 Nm
- Driveshaft Bolts44 lb-ft60 Nm
- Driveshaft Flange Bolts44 lb-ft60 Nm
- Transfer Case Bolts26 lb-ft35 Nm
- Wheel Lug Nuts133 lb-ft180 Nm
Transfer Case Chain4 specs
- CV Bolts52 lb-ft70 Nm
- CV Joint Bolts52 lb-ft71 Nm
- Driveshaft Bolts44 lb-ft60 Nm
- Driveshaft U-Joint StrapsTighten evenly15 lb-ft20 Nm
Transfer Case Encoder Motor4 specs
- CV Bolts52 lb-ft70 Nm
- CV Joint Bolts52 lb-ft71 Nm
- Driveshaft Bolts44 lb-ft60 Nm
- Driveshaft U-Joint StrapsTighten evenly15 lb-ft20 Nm
Transfer Case Fluid Change6 specs
- Air Box Clips4 lb-ft5 Nm
- Connector Bolts6 lb-ft8 Nm
- Oil Drain PlugUse new crush washer26 lb-ft35 Nm
- Transfer Case Drain Plug18 lb-ft25 Nm
- Transfer Case Fill Plug18 lb-ft25 Nm
- Wheel Lug NutsTorque in star pattern133 lb-ft180 Nm
Transfer Case Motor/Actuator4 specs
- CV Bolts52 lb-ft70 Nm
- CV Joint Bolts52 lb-ft71 Nm
- Driveshaft Bolts44 lb-ft60 Nm
- Driveshaft U-Joint StrapsTighten evenly15 lb-ft20 Nm
U-Joint8 specs
- Axle NutUse new nut, stake after207 lb-ft281 Nm
- CV Bolts52 lb-ft70 Nm
- CV Joint Bolts52 lb-ft71 Nm
- Differential Cover BoltsApply RTV sealant29 lb-ft39 Nm
- Driveshaft Bolts44 lb-ft60 Nm
- Driveshaft U-Joint StrapsTighten evenly15 lb-ft20 Nm
- Wheel Lug Nuts133 lb-ft180 Nm
- Yoke NutIf equipped111 lb-ft150 Nm
Wheel Bearing - Press-In Front7 specs
- ABS Sensor Bolt9 lb-ft12 Nm
- Axle NutUse new cotter pin or stake nut184 lb-ft250 Nm
- CV Joint Bolts52 lb-ft71 Nm
- Driveshaft Bolts48 lb-ft65 Nm
- Driveshaft U-Joint StrapsTighten evenly15 lb-ft20 Nm
- Hub Bolts86 lb-ft117 Nm
- Wheel Lug NutsTorque in star pattern133 lb-ft180 Nm
Wheel Bearing - Press-In Rear8 specs
- ABS Sensor Bolt9 lb-ft12 Nm
- Axle NutUse new cotter pin or stake nut184 lb-ft250 Nm
- CV Joint Bolts52 lb-ft71 Nm
- Differential Cover Bolts26 lb-ft35 Nm
- Driveshaft Bolts48 lb-ft65 Nm
- Driveshaft U-Joint StrapsTighten evenly15 lb-ft20 Nm
- Hub Bolts86 lb-ft117 Nm
- Wheel Lug NutsTorque in star pattern133 lb-ft180 Nm
Wheel Bearing Hub - Front4 specs
- ABS Sensor BoltDo not overtighten7 lb-ft10 Nm
- Axle NutUse new cotter pin after torque184 lb-ft250 Nm
- Caliper Bracket Bolts88 lb-ft120 Nm
- Wheel Bearing Hub BoltsApply threadlocker if specified81 lb-ft110 Nm
Wheel Bearing Hub - Rear3 specs
- Axle NutUse new cotter pin after torque148 lb-ft200 Nm
- Caliper Bracket Bolts81 lb-ft110 Nm
- Wheel Bearing Hub BoltsApply threadlocker if specified74 lb-ft100 Nm
Wheel Studs6 specs
- Axle NutUse new cotter pin or stake nut184 lb-ft250 Nm
- CV Bolts52 lb-ft70 Nm
- CV Joint Bolts52 lb-ft71 Nm
- Driveshaft Bolts48 lb-ft65 Nm
- Driveshaft U-Joint StrapsTighten evenly15 lb-ft20 Nm
- Wheel Lug NutsTorque in star pattern133 lb-ft180 Nm

Transmission

Neutral Safety Switch3 specs
- Drain PlugUse new washer15 lb-ft20 Nm
- Fill Plug15 lb-ft20 Nm
- Switch Mounting Bolts11 lb-ft15 Nm
Overdrive Solenoid5 specs
- Drain PlugUse new washer15 lb-ft20 Nm
- Fill Plug15 lb-ft20 Nm
- Flywheel BoltsOften TTY, tighten in star pattern33 lb-ft45 Nm
- Transmission Drain PlugUse new crush washer if equipped15 lb-ft20 Nm
- Transmission Pan BoltsTighten in criss-cross pattern9 lb-ft12 Nm
Pressure Plate4 specs
- Drain PlugUse new washer29 lb-ft39 Nm
- Fill Plug29 lb-ft39 Nm
- Flywheel BoltsOften TTY, tighten in star pattern70 lb-ft95 Nm
- Transmission Drain PlugUse new crush washer if equipped22 lb-ft30 Nm
Shift Cable4 specs
- Adjustment Nut7 lb-ft10 Nm
- Cable Bracket Bolts11 lb-ft15 Nm
- Drain PlugUse new washer15 lb-ft20 Nm
- Fill Plug15 lb-ft20 Nm
Shift Fork3 specs
- Drain PlugUse new washer29 lb-ft39 Nm
- Fill Plug29 lb-ft39 Nm
- Transmission Drain PlugUse new crush washer if equipped22 lb-ft30 Nm
Shift Linkage4 specs
- Drain PlugUse new washer15 lb-ft20 Nm
- Fill Plug15 lb-ft20 Nm
- Linkage Bolts11 lb-ft15 Nm
- Pivot Bolts9 lb-ft12 Nm
Shift Solenoid - Single5 specs
- Drain PlugUse new washer15 lb-ft20 Nm
- Fill Plug15 lb-ft20 Nm
- Flywheel BoltsOften TTY, tighten in star pattern33 lb-ft45 Nm
- Transmission Drain PlugUse new crush washer if equipped15 lb-ft20 Nm
- Transmission Pan BoltsTighten in criss-cross pattern9 lb-ft12 Nm
Shift Solenoids - All5 specs
- Drain PlugUse new washer15 lb-ft20 Nm
- Fill Plug15 lb-ft20 Nm
- Flywheel BoltsOften TTY, tighten in star pattern33 lb-ft45 Nm
- Transmission Drain PlugUse new crush washer if equipped15 lb-ft20 Nm
- Transmission Pan BoltsTighten in criss-cross pattern9 lb-ft12 Nm
Synchros - All5 specs
- Drain PlugUse new washer29 lb-ft39 Nm
- Fill Plug29 lb-ft39 Nm
- Flywheel BoltsOften TTY, tighten in star pattern70 lb-ft95 Nm
- Transmission Drain PlugUse new crush washer if equipped22 lb-ft30 Nm
- Transmission Pan BoltsTighten in criss-cross pattern9 lb-ft12 Nm
Synchros - Single Gear4 specs
- Drain PlugUse new washer29 lb-ft39 Nm
- Fill Plug29 lb-ft39 Nm
- Flywheel BoltsOften TTY, tighten in star pattern70 lb-ft95 Nm
- Transmission Drain PlugUse new crush washer if equipped22 lb-ft30 Nm
Torque Converter4 specs
- Drain PlugUse new washer15 lb-ft20 Nm
- Fill Plug15 lb-ft20 Nm
- Flexplate BoltsAutomatic transmissions33 lb-ft45 Nm
- Torque Converter BoltsTighten evenly37 lb-ft50 Nm
Torque Converter Clutch Solenoid5 specs
- Drain PlugUse new washer15 lb-ft20 Nm
- Fill Plug15 lb-ft20 Nm
- Flywheel BoltsOften TTY, tighten in star pattern33 lb-ft45 Nm
- Transmission Drain PlugUse new crush washer if equipped15 lb-ft20 Nm
- Transmission Pan BoltsTighten in criss-cross pattern9 lb-ft12 Nm
Transmission Control Module5 specs
- Drain PlugUse new washer15 lb-ft20 Nm
- Fill Plug15 lb-ft20 Nm
- Flywheel BoltsOften TTY, tighten in star pattern33 lb-ft45 Nm
- Transmission Drain PlugUse new crush washer if equipped15 lb-ft20 Nm
- Transmission Pan BoltsTighten in criss-cross pattern9 lb-ft12 Nm
Transmission Cooler Lines4 specs
- Drain PlugUse new washer15 lb-ft20 Nm
- Fill Plug15 lb-ft20 Nm
- Flywheel BoltsOften TTY, tighten in star pattern33 lb-ft45 Nm
- Transmission Drain PlugUse new crush washer if equipped15 lb-ft20 Nm
Transmission Filter5 specs
- Drain PlugUse new washer15 lb-ft20 Nm
- Fill Plug15 lb-ft20 Nm
- Flywheel BoltsOften TTY, tighten in star pattern33 lb-ft45 Nm
- Transmission Drain PlugUse new crush washer if equipped15 lb-ft20 Nm
- Transmission Pan BoltsTighten in criss-cross pattern9 lb-ft12 Nm
Transmission Filter and Fluid5 specs
- Drain PlugUse new washer15 lb-ft20 Nm
- Fill Plug15 lb-ft20 Nm
- Flywheel BoltsOften TTY, tighten in star pattern33 lb-ft45 Nm
- Transmission Drain PlugUse new crush washer if equipped15 lb-ft20 Nm
- Transmission Pan BoltsTighten in criss-cross pattern9 lb-ft12 Nm
Transmission Fluid Change6 specs
- Drain PlugUse new washer15 lb-ft20 Nm
- Fill Plug15 lb-ft20 Nm
- Flywheel BoltsOften TTY, tighten in star pattern33 lb-ft45 Nm
- Transmission Drain PlugUse new crush washer if equipped15 lb-ft20 Nm
- Transmission Filter BoltsIf equipped with bolted filter6 lb-ft8 Nm
- Transmission Pan BoltsTighten in criss-cross pattern9 lb-ft12 Nm
Transmission Flush5 specs
- Drain PlugUse new washer15 lb-ft20 Nm
- Fill Plug15 lb-ft20 Nm
- Flywheel BoltsOften TTY, tighten in star pattern33 lb-ft45 Nm
- Transmission Drain PlugUse new crush washer if equipped15 lb-ft20 Nm
- Transmission Pan BoltsTighten in criss-cross pattern9 lb-ft12 Nm
Transmission Input Shaft Bearing5 specs
- Drain PlugUse new washer15 lb-ft20 Nm
- Fill Plug15 lb-ft20 Nm
- Flywheel BoltsOften TTY, tighten in star pattern33 lb-ft45 Nm
- Transmission Drain PlugUse new crush washer if equipped15 lb-ft20 Nm
- Transmission Pan BoltsTighten in criss-cross pattern9 lb-ft12 Nm
Transmission Oil Cooler11 specs
- Coolant Drain Plug11 lb-ft15 Nm
- Drain PetcockHand tight6 lb-ft8 Nm
- Drain PlugUse new washer15 lb-ft20 Nm
- Fan Bolts9 lb-ft12 Nm
- Fill Plug15 lb-ft20 Nm
- Flywheel BoltsOften TTY, tighten in star pattern33 lb-ft45 Nm
- Hose Clamps2 lb-ft3 Nm
- Pump BoltsTorque in sequence7 lb-ft10 Nm
- Thermostat Housing Bolt11 lb-ft15 Nm
- Transmission Drain PlugUse new crush washer if equipped15 lb-ft20 Nm
- Water Pump BoltsTighten in criss-cross pattern15 lb-ft20 Nm
Transmission Output Shaft Bearing5 specs
- Drain PlugUse new washer15 lb-ft20 Nm
- Fill Plug15 lb-ft20 Nm
- Flywheel BoltsOften TTY, tighten in star pattern33 lb-ft45 Nm
- Transmission Drain PlugUse new crush washer if equipped15 lb-ft20 Nm
- Transmission Pan BoltsTighten in criss-cross pattern9 lb-ft12 Nm
Transmission Pan Gasket5 specs
- Drain PlugUse new washer15 lb-ft20 Nm
- Fill Plug15 lb-ft20 Nm
- Flywheel BoltsOften TTY, tighten in star pattern33 lb-ft45 Nm
- Transmission Drain PlugUse new crush washer if equipped15 lb-ft20 Nm
- Transmission Pan BoltsTighten in criss-cross pattern9 lb-ft12 Nm
Transmission R&R - Automatic5 specs
- Drain PlugUse new washer15 lb-ft20 Nm
- Fill Plug15 lb-ft20 Nm
- Flywheel BoltsOften TTY, tighten in star pattern33 lb-ft45 Nm
- Transmission Drain PlugUse new crush washer if equipped15 lb-ft20 Nm
- Transmission Pan BoltsTighten in criss-cross pattern9 lb-ft12 Nm
Transmission Range Sensor5 specs
- Drain PlugUse new washer15 lb-ft20 Nm
- Fill Plug15 lb-ft20 Nm
- Flywheel BoltsOften TTY, tighten in star pattern33 lb-ft45 Nm
- Transmission Drain PlugUse new crush washer if equipped15 lb-ft20 Nm
- Transmission Pan BoltsTighten in criss-cross pattern9 lb-ft12 Nm
Transmission Rebuild - Automatic5 specs
- Drain PlugUse new washer15 lb-ft20 Nm
- Fill Plug15 lb-ft20 Nm
- Flywheel BoltsOften TTY, tighten in star pattern33 lb-ft45 Nm
- Transmission Drain PlugUse new crush washer if equipped15 lb-ft20 Nm
- Transmission Pan BoltsTighten in criss-cross pattern9 lb-ft12 Nm
Transmission Speed Sensor - Input5 specs
- Drain PlugUse new washer15 lb-ft20 Nm
- Fill Plug15 lb-ft20 Nm
- Flywheel BoltsOften TTY, tighten in star pattern33 lb-ft45 Nm
- Transmission Drain PlugUse new crush washer if equipped15 lb-ft20 Nm
- Transmission Pan BoltsTighten in criss-cross pattern9 lb-ft12 Nm
Transmission Speed Sensor - Output4 specs
- Drain PlugUse new washer15 lb-ft20 Nm
- Fill Plug15 lb-ft20 Nm
- Flywheel BoltsOften TTY, tighten in star pattern33 lb-ft45 Nm
- Transmission Drain PlugUse new crush washer if equipped15 lb-ft20 Nm
Valve Body5 specs
- Drain PlugUse new washer15 lb-ft20 Nm
- Fill Plug15 lb-ft20 Nm
- Flywheel BoltsOften TTY, tighten in star pattern33 lb-ft45 Nm
- Transmission Drain PlugUse new crush washer if equipped15 lb-ft20 Nm
- Transmission Pan BoltsTighten in criss-cross pattern9 lb-ft12 Nm

Exhaust

Air Injection Check Valve4 specs
- Exhaust Flange BoltApply anti-seize33 lb-ft45 Nm
- Hanger Bolts17 lb-ft23 Nm
- Heat Shield Bolts7 lb-ft10 Nm
- Manifold NutsApply anti-seize29 lb-ft39 Nm
Catalytic Converter - Direct Fit5 specs
- Exhaust Flange BoltApply anti-seize18 lb-ft25 Nm
- Hanger Bolts17 lb-ft23 Nm
- Heat Shield Bolts7 lb-ft10 Nm
- Manifold NutsApply anti-seize18 lb-ft25 Nm
- O2 SensorApply anti-seize to threads only33 lb-ft45 Nm
Catalytic Converter - Universal5 specs
- Exhaust Flange BoltApply anti-seize18 lb-ft25 Nm
- Hanger Bolts17 lb-ft23 Nm
- Heat Shield Bolts7 lb-ft10 Nm
- Manifold NutsApply anti-seize18 lb-ft25 Nm
- O2 SensorApply anti-seize to threads only33 lb-ft45 Nm
Downpipe5 specs
- Exhaust Flange BoltApply anti-seize18 lb-ft25 Nm
- Hanger Bolts17 lb-ft23 Nm
- Heat Shield Bolts7 lb-ft10 Nm
- Manifold NutsApply anti-seize18 lb-ft25 Nm
- O2 SensorApply anti-seize to threads only33 lb-ft45 Nm
EGR Tube5 specs
- Exhaust Flange BoltApply anti-seize33 lb-ft45 Nm
- Hanger Bolts17 lb-ft23 Nm
- Heat Shield Bolts7 lb-ft10 Nm
- Manifold NutsApply anti-seize29 lb-ft39 Nm
- O2 SensorApply anti-seize to threads only33 lb-ft45 Nm
EGR Valve6 specs
- EGR Tube Fitting26 lb-ft35 Nm
- EGR Valve Bolts18 lb-ft25 Nm
- Hanger Bolts17 lb-ft23 Nm
- Heat Shield Bolts12 lb-ft16 Nm
- Manifold NutsApply anti-seize29 lb-ft39 Nm
- O2 SensorApply anti-seize to threads40 lb-ft54 Nm
Exhaust Clamp5 specs
- Exhaust Flange BoltApply anti-seize33 lb-ft45 Nm
- Hanger Bolts17 lb-ft23 Nm
- Heat Shield Bolts7 lb-ft10 Nm
- Manifold NutsApply anti-seize18 lb-ft25 Nm
- O2 SensorApply anti-seize to threads only33 lb-ft45 Nm
Exhaust Gasket - Front5 specs
- Exhaust Flange BoltApply anti-seize33 lb-ft45 Nm
- Hanger Bolts17 lb-ft23 Nm
- Heat Shield Bolts7 lb-ft10 Nm
- Manifold NutsApply anti-seize18 lb-ft25 Nm
- O2 SensorApply anti-seize to threads only33 lb-ft45 Nm
Exhaust Gasket - Rear5 specs
- Exhaust Flange BoltApply anti-seize18 lb-ft25 Nm
- Hanger Bolts17 lb-ft23 Nm
- Heat Shield Bolts7 lb-ft10 Nm
- Manifold NutsApply anti-seize29 lb-ft39 Nm
- O2 SensorApply anti-seize to threads only33 lb-ft45 Nm
Exhaust Hangers5 specs
- Exhaust Flange BoltApply anti-seize18 lb-ft25 Nm
- Hanger Bolts17 lb-ft23 Nm
- Heat Shield Bolts7 lb-ft10 Nm
- Manifold NutsApply anti-seize29 lb-ft39 Nm
- O2 SensorApply anti-seize to threads only33 lb-ft45 Nm
Exhaust Manifold Studs5 specs
- Exhaust Flange BoltApply anti-seize18 lb-ft25 Nm
- Hanger Bolts17 lb-ft23 Nm
- Heat Shield Bolts7 lb-ft10 Nm
- Manifold NutsApply anti-seize29 lb-ft39 Nm
- O2 SensorApply anti-seize to threads only33 lb-ft45 Nm
Exhaust Pipe - Rear Section5 specs
- Exhaust Flange BoltApply anti-seize18 lb-ft25 Nm
- Hanger Bolts17 lb-ft23 Nm
- Heat Shield Bolts7 lb-ft10 Nm
- Manifold NutsApply anti-seize29 lb-ft39 Nm
- O2 SensorApply anti-seize to threads only33 lb-ft45 Nm
Exhaust Tip3 specs
- Exhaust Flange BoltApply anti-seize33 lb-ft45 Nm
- Hanger Bolts17 lb-ft23 Nm
- Manifold NutsApply anti-seize29 lb-ft39 Nm
Flex Pipe5 specs
- Exhaust Clamps41 lb-ft55 Nm
- Hanger Bolts17 lb-ft23 Nm
- Heat Shield Bolts12 lb-ft16 Nm
- Manifold NutsApply anti-seize29 lb-ft39 Nm
- O2 SensorApply anti-seize to threads33 lb-ft45 Nm
Front Pipe5 specs
- Exhaust Flange BoltApply anti-seize18 lb-ft25 Nm
- Hanger Bolts17 lb-ft23 Nm
- Heat Shield Bolts7 lb-ft10 Nm
- Manifold NutsApply anti-seize29 lb-ft39 Nm
- O2 SensorApply anti-seize to threads only33 lb-ft45 Nm
Intermediate Pipe5 specs
- Exhaust Flange BoltApply anti-seize18 lb-ft25 Nm
- Hanger Bolts17 lb-ft23 Nm
- Heat Shield Bolts7 lb-ft10 Nm
- Manifold NutsApply anti-seize18 lb-ft25 Nm
- O2 SensorApply anti-seize to threads only33 lb-ft45 Nm
Muffler2 specs
- Hanger Bracket Bolts18 lb-ft25 Nm
- Muffler Clamps41 lb-ft55 Nm
O2 Sensor - Downstream5 specs
- Exhaust Flange BoltApply anti-seize33 lb-ft45 Nm
- Hanger Bolts17 lb-ft23 Nm
- Heat Shield Bolts7 lb-ft10 Nm
- Manifold NutsApply anti-seize18 lb-ft25 Nm
- O2 SensorApply anti-seize to threads only33 lb-ft45 Nm
O2 Sensor - Upstream5 specs
- Exhaust Flange BoltApply anti-seize33 lb-ft45 Nm
- Hanger Bolts17 lb-ft23 Nm
- Heat Shield Bolts7 lb-ft10 Nm
- Manifold NutsApply anti-seize18 lb-ft25 Nm
- O2 SensorApply anti-seize to threads only33 lb-ft45 Nm
O2 Sensors - All5 specs
- Exhaust Flange BoltApply anti-seize33 lb-ft45 Nm
- Hanger Bolts17 lb-ft23 Nm
- Heat Shield Bolts7 lb-ft10 Nm
- Manifold NutsApply anti-seize18 lb-ft25 Nm
- O2 SensorApply anti-seize to threads only33 lb-ft45 Nm
Resonator5 specs
- Exhaust Clamps41 lb-ft55 Nm
- Hanger Bolts17 lb-ft23 Nm
- Heat Shield Bolts12 lb-ft16 Nm
- Manifold NutsApply anti-seize18 lb-ft25 Nm
- O2 SensorApply anti-seize to threads33 lb-ft45 Nm
Secondary Air Injection Pump4 specs
- Exhaust Flange BoltApply anti-seize33 lb-ft45 Nm
- Hanger Bolts17 lb-ft23 Nm
- Heat Shield Bolts7 lb-ft10 Nm
- Manifold NutsApply anti-seize29 lb-ft39 Nm
Tail Pipe5 specs
- Exhaust Flange BoltApply anti-seize18 lb-ft25 Nm
- Hanger Bolts17 lb-ft23 Nm
- Heat Shield Bolts7 lb-ft10 Nm
- Manifold NutsApply anti-seize18 lb-ft25 Nm
- O2 SensorApply anti-seize to threads only33 lb-ft45 Nm

Heating and A/C

AC Accumulator5 specs
- AC Line FittingsUse new O-rings, add PAG oil15 lb-ft20 Nm
- Blower Motor Mounting Screw3 lb-ft4 Nm
- Compressor Bolts29 lb-ft39 Nm
- Duct Clips2 lb-ft3 Nm
- Mounting Bracket Bolts21 lb-ft28 Nm
AC Clutch Coil5 specs
- AC Line FittingsUse new O-rings, add PAG oil15 lb-ft20 Nm
- Blower Motor Mounting Screw3 lb-ft4 Nm
- Compressor Bolts29 lb-ft39 Nm
- Duct Clips2 lb-ft3 Nm
- Mounting Bracket Bolts21 lb-ft28 Nm
AC Compressor3 specs
- AC Compressor Bolts18 lb-ft25 Nm
- AC Line FittingsUse new O-rings, add PAG oil15 lb-ft20 Nm
- Clutch Connector Bolt6 lb-ft8 Nm
AC Compressor Clutch5 specs
- AC Line FittingsUse new O-rings, add PAG oil15 lb-ft20 Nm
- Blower Motor Mounting Screw3 lb-ft4 Nm
- Compressor Bolts29 lb-ft39 Nm
- Duct Clips2 lb-ft3 Nm
- Mounting Bracket Bolts21 lb-ft28 Nm
AC Compressor Oil Add5 specs
- AC Line FittingsUse new O-rings, add PAG oil15 lb-ft20 Nm
- Blower Motor Mounting Screw3 lb-ft4 Nm
- Compressor Bolts29 lb-ft39 Nm
- Duct Clips2 lb-ft3 Nm
- Mounting Bracket Bolts21 lb-ft28 Nm
AC Condenser2 specs
- AC Line FittingsUse new O-rings15 lb-ft20 Nm
- Condenser Mounting Bolts9 lb-ft12 Nm
AC Evaporator7 specs
- AC Line FittingsUse new O-rings, add PAG oil15 lb-ft20 Nm
- Blower Motor Mounting Screw6 lb-ft8 Nm
- Compressor Bolts29 lb-ft39 Nm
- Duct Clips2 lb-ft3 Nm
- Evaporator Case Screws4 lb-ft5 Nm
- Expansion Valve7 lb-ft10 Nm
- Mounting Bracket Bolts21 lb-ft28 Nm
AC Expansion Valve (TXV)6 specs
- AC Line FittingsUse new O-rings, add PAG oil15 lb-ft20 Nm
- Blower Motor Mounting Screw6 lb-ft8 Nm
- Compressor Bolts29 lb-ft39 Nm
- Duct Clips2 lb-ft3 Nm
- Expansion Valve7 lb-ft10 Nm
- Mounting Bracket Bolts21 lb-ft28 Nm
AC High Pressure Switch5 specs
- AC Line FittingsUse new O-rings, add PAG oil15 lb-ft20 Nm
- Blower Motor Mounting Screw3 lb-ft4 Nm
- Compressor Bolts29 lb-ft39 Nm
- Duct Clips2 lb-ft3 Nm
- Mounting Bracket Bolts21 lb-ft28 Nm
AC Hose - High Side5 specs
- AC Line FittingsUse new O-rings, add PAG oil15 lb-ft20 Nm
- Blower Motor Mounting Screw3 lb-ft4 Nm
- Compressor Bolts29 lb-ft39 Nm
- Duct Clips2 lb-ft3 Nm
- Mounting Bracket Bolts21 lb-ft28 Nm
AC Hose - Low Side6 specs
- AC Line FittingsUse new O-rings, add PAG oil15 lb-ft20 Nm
- Blower Motor Mounting Screw3 lb-ft4 Nm
- Compressor Bolts18 lb-ft25 Nm
- Duct Clips2 lb-ft3 Nm
- Hose Clamps2 lb-ft3 Nm
- Mounting Bracket Bolts21 lb-ft28 Nm
AC Hose Assembly6 specs
- AC Line FittingsUse new O-rings, add PAG oil15 lb-ft20 Nm
- Blower Motor Mounting Screw3 lb-ft4 Nm
- Compressor Bolts29 lb-ft39 Nm
- Duct Clips2 lb-ft3 Nm
- Hose Clamps2 lb-ft3 Nm
- Mounting Bracket Bolts21 lb-ft28 Nm
AC Low Pressure Switch5 specs
- AC Line FittingsUse new O-rings, add PAG oil15 lb-ft20 Nm
- Blower Motor Mounting Screw3 lb-ft4 Nm
- Compressor Bolts29 lb-ft39 Nm
- Duct Clips2 lb-ft3 Nm
- Mounting Bracket Bolts21 lb-ft28 Nm
AC Orifice Tube5 specs
- AC Line FittingsUse new O-rings, add PAG oil15 lb-ft20 Nm
- Blower Motor Mounting Screw3 lb-ft4 Nm
- Compressor Bolts29 lb-ft39 Nm
- Duct Clips2 lb-ft3 Nm
- Mounting Bracket Bolts21 lb-ft28 Nm
AC Pressure Sensor5 specs
- AC Line FittingsUse new O-rings, add PAG oil15 lb-ft20 Nm
- Blower Motor Mounting Screw3 lb-ft4 Nm
- Compressor Bolts18 lb-ft25 Nm
- Duct Clips2 lb-ft3 Nm
- Mounting Bracket Bolts21 lb-ft28 Nm
AC Receiver/Drier6 specs
- AC Line FittingsUse new O-rings, add PAG oil15 lb-ft20 Nm
- Blower Motor Mounting Screw6 lb-ft8 Nm
- Compressor Bolts18 lb-ft25 Nm
- Duct Clips2 lb-ft3 Nm
- Mounting Bracket Bolts21 lb-ft28 Nm
- Receiver Drier Bolts7 lb-ft10 Nm
AC Recharge5 specs
- AC Line FittingsUse new O-rings, add PAG oil15 lb-ft20 Nm
- Blower Motor Mounting Screw3 lb-ft4 Nm
- Compressor Bolts18 lb-ft25 Nm
- Duct Clips2 lb-ft3 Nm
- Mounting Bracket Bolts21 lb-ft28 Nm
Blend Door Actuator5 specs
- Actuator Screws2 lb-ft3 Nm
- Blower Motor Mounting Screw6 lb-ft8 Nm
- Compressor Bolts15 lb-ft20 Nm
- Duct Clips2 lb-ft3 Nm
- Mounting Bracket Bolts21 lb-ft28 Nm
Cabin Air Filter4 specs
- Compressor Bolts29 lb-ft39 Nm
- Connector Bolts6 lb-ft8 Nm
- Filter Cover ClipsTool-free on most2 lb-ft3 Nm
- Glove Box Screws3 lb-ft4 Nm
Climate Control Module5 specs
- AC Line FittingsUse new O-rings, add PAG oil15 lb-ft20 Nm
- Blower Motor Mounting Screw3 lb-ft4 Nm
- Compressor Bolts18 lb-ft25 Nm
- Duct Clips2 lb-ft3 Nm
- Mounting Bracket Bolts21 lb-ft28 Nm
HVAC Control Panel5 specs
- AC Line FittingsUse new O-rings, add PAG oil15 lb-ft20 Nm
- Blower Motor Mounting Screw3 lb-ft4 Nm
- Compressor Bolts29 lb-ft39 Nm
- Duct Clips2 lb-ft3 Nm
- Mounting Bracket Bolts21 lb-ft28 Nm
Mode Door Actuator4 specs
- Blower Motor Mounting Screw3 lb-ft4 Nm
- Compressor Bolts29 lb-ft39 Nm
- Duct Clips2 lb-ft3 Nm
- Mounting Bracket Bolts21 lb-ft28 Nm
Recirculation Door Actuator5 specs
- AC Line FittingsUse new O-rings, add PAG oil15 lb-ft20 Nm
- Blower Motor Mounting Screw3 lb-ft4 Nm
- Compressor Bolts18 lb-ft25 Nm
- Duct Clips2 lb-ft3 Nm
- Mounting Bracket Bolts21 lb-ft28 Nm

Body

Bumper Cover - Front8 specs
- Bumper Cover Bolts7 lb-ft10 Nm
- Fender Liner Screws2 lb-ft3 Nm
- Grille Clips4 lb-ft5 Nm
- Hinge Bolts23 lb-ft31 Nm
- Latch Bolts12 lb-ft16 Nm
- Panel Bolts12 lb-ft16 Nm
- Striker Bolts29 lb-ft39 Nm
- Trim ClipsReplace if broken2 lb-ft3 Nm
Bumper Cover - Rear7 specs
- Bumper Cover Bolts7 lb-ft10 Nm
- Hinge Bolts23 lb-ft31 Nm
- Latch Bolts12 lb-ft16 Nm
- Panel Bolts12 lb-ft16 Nm
- Striker Bolts29 lb-ft39 Nm
- Trim ClipsReplace if broken2 lb-ft3 Nm
- Trunk Liner Screws2 lb-ft3 Nm
Bumper Reinforcement - Front7 specs
- Body Panel Bolts18 lb-ft25 Nm
- Bumper Cover Bolts7 lb-ft10 Nm
- Hinge Bolts23 lb-ft31 Nm
- Latch Bolts12 lb-ft16 Nm
- Panel Bolts12 lb-ft16 Nm
- Striker Bolts29 lb-ft39 Nm
- Trim ClipsReplace if broken2 lb-ft3 Nm
Bumper Reinforcement - Rear7 specs
- Body Panel Bolts18 lb-ft25 Nm
- Bumper Cover Bolts7 lb-ft10 Nm
- Hinge Bolts23 lb-ft31 Nm
- Latch Bolts12 lb-ft16 Nm
- Panel Bolts12 lb-ft16 Nm
- Striker Bolts29 lb-ft39 Nm
- Trim ClipsReplace if broken2 lb-ft3 Nm
Door Check/Stop7 specs
- Body Panel Bolts18 lb-ft25 Nm
- Door Hinge Bolts30 lb-ft40 Nm
- Hinge Bolts30 lb-ft40 Nm
- Latch Bolts12 lb-ft16 Nm
- Panel Bolts12 lb-ft16 Nm
- Striker Bolts29 lb-ft39 Nm
- Trim ClipsReplace if broken2 lb-ft3 Nm
Door Glass6 specs
- Door Hinge Bolts30 lb-ft40 Nm
- Hinge Bolts23 lb-ft31 Nm
- Latch Bolts12 lb-ft16 Nm
- Panel Bolts12 lb-ft16 Nm
- Striker Bolts29 lb-ft39 Nm
- Trim ClipsReplace if broken2 lb-ft3 Nm
Door Handle - Exterior7 specs
- Handle Mounting Bolts6 lb-ft8 Nm
- Hinge Bolts23 lb-ft31 Nm
- Latch Bolts12 lb-ft16 Nm
- Lock Rod Clips4 lb-ft5 Nm
- Panel Bolts12 lb-ft16 Nm
- Striker Bolts29 lb-ft39 Nm
- Trim ClipsReplace if broken2 lb-ft3 Nm
Door Handle - Interior7 specs
- Cable Clips4 lb-ft5 Nm
- Handle Screws2 lb-ft3 Nm
- Hinge Bolts23 lb-ft31 Nm
- Latch Bolts12 lb-ft16 Nm
- Panel Bolts12 lb-ft16 Nm
- Striker Bolts29 lb-ft39 Nm
- Trim ClipsReplace if broken2 lb-ft3 Nm
Door Hinge6 specs
- Door Hinge Bolts30 lb-ft40 Nm
- Hinge Bolts30 lb-ft40 Nm
- Latch Bolts12 lb-ft16 Nm
- Panel Bolts12 lb-ft16 Nm
- Striker Bolts29 lb-ft39 Nm
- Trim ClipsReplace if broken2 lb-ft3 Nm
Door Shell7 specs
- Body Panel Bolts18 lb-ft25 Nm
- Door Hinge Bolts30 lb-ft40 Nm
- Hinge Bolts30 lb-ft40 Nm
- Latch Bolts12 lb-ft16 Nm
- Panel Bolts12 lb-ft16 Nm
- Striker Bolts29 lb-ft39 Nm
- Trim ClipsReplace if broken2 lb-ft3 Nm
Door Skin7 specs
- Body Panel Bolts18 lb-ft25 Nm
- Door Hinge Bolts30 lb-ft40 Nm
- Hinge Bolts30 lb-ft40 Nm
- Latch Bolts12 lb-ft16 Nm
- Panel Bolts12 lb-ft16 Nm
- Striker Bolts29 lb-ft39 Nm
- Trim ClipsReplace if broken2 lb-ft3 Nm
Door Weatherstrip6 specs
- Door Hinge Bolts22 lb-ft30 Nm
- Hinge Bolts23 lb-ft31 Nm
- Latch Bolts12 lb-ft16 Nm
- Panel Bolts12 lb-ft16 Nm
- Striker Bolts29 lb-ft39 Nm
- Trim ClipsReplace if broken2 lb-ft3 Nm
Fender8 specs
- Fender Bolts9 lb-ft12 Nm
- Fender Liner Screws2 lb-ft3 Nm
- Hinge Bolts23 lb-ft31 Nm
- Hood Hinge Bolts18 lb-ft25 Nm
- Latch Bolts12 lb-ft16 Nm
- Panel Bolts12 lb-ft16 Nm
- Striker Bolts29 lb-ft39 Nm
- Trim ClipsReplace if broken2 lb-ft3 Nm
Fender Liner7 specs
- Body Panel Bolts18 lb-ft25 Nm
- Bumper Cover Bolts7 lb-ft10 Nm
- Hinge Bolts23 lb-ft31 Nm
- Latch Bolts12 lb-ft16 Nm
- Panel Bolts12 lb-ft16 Nm
- Striker Bolts29 lb-ft39 Nm
- Trim ClipsReplace if broken2 lb-ft3 Nm
Grille7 specs
- Clips4 lb-ft5 Nm
- Grille Mounting Screws2 lb-ft3 Nm
- Hinge Bolts23 lb-ft31 Nm
- Latch Bolts12 lb-ft16 Nm
- Panel Bolts12 lb-ft16 Nm
- Striker Bolts29 lb-ft39 Nm
- Trim ClipsReplace if broken2 lb-ft3 Nm
Hood8 specs
- Hinge Bolts23 lb-ft31 Nm
- Hood Hinge Bolts18 lb-ft25 Nm
- Hood Latch Bolts9 lb-ft12 Nm
- Hood Strut Bolts7 lb-ft10 Nm
- Latch Bolts12 lb-ft16 Nm
- Panel Bolts12 lb-ft16 Nm
- Striker Bolts29 lb-ft39 Nm
- Trim ClipsReplace if broken2 lb-ft3 Nm
Hood Hinge6 specs
- Body Panel Bolts18 lb-ft25 Nm
- Hinge Bolts23 lb-ft31 Nm
- Latch Bolts12 lb-ft16 Nm
- Panel Bolts12 lb-ft16 Nm
- Striker Bolts29 lb-ft39 Nm
- Trim ClipsReplace if broken2 lb-ft3 Nm
Hood Latch7 specs
- Cable Clips4 lb-ft5 Nm
- Hinge Bolts23 lb-ft31 Nm
- Hood Latch Bolts9 lb-ft12 Nm
- Latch Bolts12 lb-ft16 Nm
- Panel Bolts12 lb-ft16 Nm
- Striker Bolts29 lb-ft39 Nm
- Trim ClipsReplace if broken2 lb-ft3 Nm
Hood Release Cable7 specs
- Body Panel Bolts18 lb-ft25 Nm
- Bumper Cover Bolts7 lb-ft10 Nm
- Hinge Bolts23 lb-ft31 Nm
- Latch Bolts12 lb-ft16 Nm
- Panel Bolts12 lb-ft16 Nm
- Striker Bolts29 lb-ft39 Nm
- Trim ClipsReplace if broken2 lb-ft3 Nm
Hood Strut6 specs
- Body Panel Bolts18 lb-ft25 Nm
- Hinge Bolts23 lb-ft31 Nm
- Latch Bolts12 lb-ft16 Nm
- Panel Bolts12 lb-ft16 Nm
- Striker Bolts29 lb-ft39 Nm
- Trim ClipsReplace if broken2 lb-ft3 Nm
Liftgate7 specs
- Body Panel Bolts18 lb-ft25 Nm
- Door Hinge Bolts22 lb-ft30 Nm
- Hinge Bolts23 lb-ft31 Nm
- Latch Bolts12 lb-ft16 Nm
- Panel Bolts12 lb-ft16 Nm
- Striker Bolts15 lb-ft20 Nm
- Trim ClipsReplace if broken2 lb-ft3 Nm
Liftgate Motor7 specs
- Body Panel Bolts18 lb-ft25 Nm
- Door Hinge Bolts22 lb-ft30 Nm
- Hinge Bolts23 lb-ft31 Nm
- Latch Bolts12 lb-ft16 Nm
- Panel Bolts12 lb-ft16 Nm
- Striker Bolts29 lb-ft39 Nm
- Trim ClipsReplace if broken2 lb-ft3 Nm
Liftgate Strut7 specs
- Body Panel Bolts18 lb-ft25 Nm
- Door Hinge Bolts22 lb-ft30 Nm
- Hinge Bolts23 lb-ft31 Nm
- Latch Bolts12 lb-ft16 Nm
- Panel Bolts12 lb-ft16 Nm
- Striker Bolts29 lb-ft39 Nm
- Trim ClipsReplace if broken2 lb-ft3 Nm
Quarter Glass7 specs
- Body Panel Bolts18 lb-ft25 Nm
- Door Hinge Bolts30 lb-ft40 Nm
- Hinge Bolts30 lb-ft40 Nm
- Latch Bolts12 lb-ft16 Nm
- Panel Bolts12 lb-ft16 Nm
- Striker Bolts18 lb-ft25 Nm
- Trim ClipsReplace if broken2 lb-ft3 Nm
Quarter Panel8 specs
- Body Panel Bolts18 lb-ft25 Nm
- Bumper Cover Bolts7 lb-ft10 Nm
- Door Hinge Bolts30 lb-ft40 Nm
- Hinge Bolts30 lb-ft40 Nm
- Latch Bolts12 lb-ft16 Nm
- Panel Bolts12 lb-ft16 Nm
- Striker Bolts18 lb-ft25 Nm
- Trim ClipsReplace if broken2 lb-ft3 Nm
Rear Window7 specs
- Body Panel Bolts18 lb-ft25 Nm
- Door Hinge Bolts22 lb-ft30 Nm
- Hinge Bolts23 lb-ft31 Nm
- Latch Bolts12 lb-ft16 Nm
- Panel Bolts12 lb-ft16 Nm
- Striker Bolts29 lb-ft39 Nm
- Trim ClipsReplace if broken2 lb-ft3 Nm
Rocker Panel8 specs
- Body Panel Bolts18 lb-ft25 Nm
- Bumper Cover Bolts7 lb-ft10 Nm
- Door Hinge Bolts22 lb-ft30 Nm
- Hinge Bolts23 lb-ft31 Nm
- Latch Bolts12 lb-ft16 Nm
- Panel Bolts12 lb-ft16 Nm
- Striker Bolts29 lb-ft39 Nm
- Trim ClipsReplace if broken2 lb-ft3 Nm
Side Mirror Glass5 specs
- Hinge Bolts23 lb-ft31 Nm
- Latch Bolts12 lb-ft16 Nm
- Panel Bolts12 lb-ft16 Nm
- Striker Bolts29 lb-ft39 Nm
- Trim ClipsReplace if broken2 lb-ft3 Nm
Windshield6 specs
- Body Panel Bolts18 lb-ft25 Nm
- Hinge Bolts23 lb-ft31 Nm
- Latch Bolts12 lb-ft16 Nm
- Panel Bolts12 lb-ft16 Nm
- Striker Bolts29 lb-ft39 Nm
- Trim ClipsReplace if broken2 lb-ft3 Nm
Windshield Molding5 specs
- Hinge Bolts23 lb-ft31 Nm
- Latch Bolts12 lb-ft16 Nm
- Panel Bolts12 lb-ft16 Nm
- Striker Bolts29 lb-ft39 Nm
- Trim ClipsReplace if broken2 lb-ft3 Nm

Interior

Armrest3 specs
- Connector Bolts6 lb-ft8 Nm
- Seat Mounting BoltsSafety critical33 lb-ft45 Nm
- Trim Panel ClipsReplace if damaged1.5 lb-ft2 Nm
Carpet4 specs
- Connector Bolts6 lb-ft8 Nm
- Dashboard Screws2 lb-ft3 Nm
- Seat Mounting BoltsSafety critical33 lb-ft45 Nm
- Trim Panel ClipsReplace if damaged1.5 lb-ft2 Nm
Center Console3 specs
- Connector Bolts6 lb-ft8 Nm
- Console Screws2 lb-ft3 Nm
- Shifter Trim4 lb-ft5 Nm
Dash Pad4 specs
- Connector Bolts6 lb-ft8 Nm
- Dashboard Screws2 lb-ft3 Nm
- Seat Mounting BoltsSafety critical33 lb-ft45 Nm
- Trim Panel ClipsReplace if damaged1.5 lb-ft2 Nm
Dashboard4 specs
- Connector Bolts6 lb-ft8 Nm
- Dashboard Bolt9 lb-ft12 Nm
- Dashboard Screws2 lb-ft3 Nm
- Trim Panel ClipsReplace if damaged1.5 lb-ft2 Nm
Door Panel3 specs
- Connector Bolts6 lb-ft8 Nm
- Door Panel Screws1.5 lb-ft2 Nm
- Trim Panel ClipsReplace if damaged1.5 lb-ft2 Nm
Floor Mat Hooks2 specs
- Connector Bolts6 lb-ft8 Nm
- Trim Panel ClipsReplace if damaged1.5 lb-ft2 Nm
Glove Box3 specs
- Connector Bolts6 lb-ft8 Nm
- Glove Box Screws2 lb-ft3 Nm
- Hinge Screws1.5 lb-ft2 Nm
Glove Box Latch3 specs
- Connector Bolts6 lb-ft8 Nm
- Dashboard Screws2 lb-ft3 Nm
- Trim Panel ClipsReplace if damaged1.5 lb-ft2 Nm
Headliner3 specs
- Connector Bolts6 lb-ft8 Nm
- Seat Mounting BoltsSafety critical33 lb-ft45 Nm
- Trim Panel ClipsReplace if damaged1.5 lb-ft2 Nm
Pedal Pads3 specs
- Connector Bolts6 lb-ft8 Nm
- Seat Mounting BoltsSafety critical33 lb-ft45 Nm
- Trim Panel ClipsReplace if damaged1.5 lb-ft2 Nm
Rearview Mirror2 specs
- Connector Bolts6 lb-ft8 Nm
- Trim Panel ClipsReplace if damaged1.5 lb-ft2 Nm
Seat - Front4 specs
- Connector Bolts6 lb-ft8 Nm
- Electrical Connectors4 lb-ft5 Nm
- Seat Mounting BoltsSafety critical33 lb-ft45 Nm
- Seat Track Bolts33 lb-ft45 Nm
Seat - Rear3 specs
- Connector Bolts6 lb-ft8 Nm
- Seat Back Release11 lb-ft15 Nm
- Seat Mounting Bolts26 lb-ft35 Nm
Seat Belt3 specs
- Connector Bolts6 lb-ft8 Nm
- Seat Mounting BoltsSafety critical33 lb-ft45 Nm
- Trim Panel ClipsReplace if damaged1.5 lb-ft2 Nm
Seat Belt Buckle3 specs
- Connector Bolts6 lb-ft8 Nm
- Seat Mounting BoltsSafety critical33 lb-ft45 Nm
- Trim Panel ClipsReplace if damaged1.5 lb-ft2 Nm
Seat Belt Pretensioner3 specs
- Connector Bolts6 lb-ft8 Nm
- Seat Mounting BoltsSafety critical33 lb-ft45 Nm
- Trim Panel ClipsReplace if damaged1.5 lb-ft2 Nm
Seat Cover3 specs
- Connector Bolts6 lb-ft8 Nm
- Seat Mounting BoltsSafety critical33 lb-ft45 Nm
- Trim Panel ClipsReplace if damaged1.5 lb-ft2 Nm
Seat Foam3 specs
- Connector Bolts6 lb-ft8 Nm
- Seat Mounting BoltsSafety critical33 lb-ft45 Nm
- Trim Panel ClipsReplace if damaged1.5 lb-ft2 Nm
Seat Track3 specs
- Connector Bolts6 lb-ft8 Nm
- Seat Mounting BoltsSafety critical33 lb-ft45 Nm
- Trim Panel ClipsReplace if damaged1.5 lb-ft2 Nm
Shifter Boot3 specs
- Connector Bolts6 lb-ft8 Nm
- Seat Mounting BoltsSafety critical33 lb-ft45 Nm
- Trim Panel ClipsReplace if damaged1.5 lb-ft2 Nm
Shifter Knob3 specs
- Connector Bolts6 lb-ft8 Nm
- Seat Mounting BoltsSafety critical33 lb-ft45 Nm
- Trim Panel ClipsReplace if damaged1.5 lb-ft2 Nm
Steering Wheel Cover4 specs
- Connector Bolts6 lb-ft8 Nm
- Dashboard ScrewsVerify sequence with the service manual2 lb-ft3 Nm
- Seat Mounting BoltsSafety critical. Verify sequence with the service manual33 lb-ft45 Nm
- Trim Panel ClipsReplace if damaged. Verify sequence with the service manual1.5 lb-ft2 Nm
Sun Visor2 specs
- Connector Bolts6 lb-ft8 Nm
- Visor Mounting Screws2 lb-ft3 Nm

Torque is shown in lb-ft with Nm below it. Where a step says to turn, tighten the listed angle after the torque step before it. Use new bolts where the note says so.

Need labor times, fluids or repair steps for this car? See it on the Open Labor Project