RQUE SPECS2020 McLaren Senna torque specs
4.0L V8 Twin Turbo
Change vehicle
Most looked up
- Lug nuts118 lb-ft160 Nm
- Oil drain plug26 lb-ft35 Nm
- Spark plugs18 lb-ft25 Nm
- Front caliper bracket bolts88 lb-ft120 Nm
- Rear caliper bracket bolts74 lb-ft100 Nm
- Front axle nut184 lb-ft250 Nm
- Outer tie rod end nut46 lb-ft62 Nm
Maintenance
AC System Diagnosis1 spec
- AC Line FittingsNew O-rings17 lb-ft23 Nm
Air Filter3 specs
- Air Box Clips4 lb-ft5 Nm
- MAF Sensor Screws3 lb-ft5 Nm
- Mass Air Flow Sensor Screws2.2 lb-ft3 Nm
Battery Test3 specs
- Battery Hold-Down BoltDo not overtighten4.4 lb-ft6 Nm
- Battery Terminal BoltsClean terminals6 lb-ft8 Nm
- Ground Cable Bolt7 lb-ft9 Nm
Charging System Test1 spec
- Oil Drain PlugUse new crush washer18 lb-ft25 Nm
Check Engine Light Diagnosis1 spec
- Oil Drain PlugUse new crush washer18 lb-ft25 Nm
Compression Test1 spec
- Air Box Clips4 lb-ft5 Nm
Differential Service3 specs
- Drain PlugNew washer35 lb-ft47 Nm
- Fill Plug35 lb-ft47 Nm
- Oil Drain PlugUse new crush washer18 lb-ft25 Nm
Drivability Diagnosis2 specs
- Air Box Clips4 lb-ft5 Nm
- Oil Drain PlugUse new crush washer18 lb-ft25 Nm
Electrical Diagnosis1 spec
- Oil Drain PlugUse new crush washer18 lb-ft25 Nm
Leak-Down Test1 spec
- Air Box Clips4 lb-ft5 Nm
Noise Diagnosis1 spec
- Wheel Lug NutsTorque in star pattern118 lb-ft160 Nm
Tire Balance2 specs
- Oil Drain PlugUse new crush washer18 lb-ft25 Nm
- Wheel Lug NutsTorque in star pattern118 lb-ft160 Nm
Tire Mount and Balance2 specs
- Oil Drain PlugUse new crush washer18 lb-ft25 Nm
- Wheel Lug NutsTorque in star pattern118 lb-ft160 Nm
Tire Rotation2 specs
- Lug Nuts - Alloy WheelsTorque in star pattern, recheck after 50 miles118 lb-ft160 Nm
- Lug Nuts - Steel WheelsTorque in star pattern118 lb-ft160 Nm
TPMS Relearn1 spec
- Oil Drain PlugUse new crush washer18 lb-ft25 Nm
TPMS Sensor2 specs
- Oil Drain PlugUse new crush washer18 lb-ft25 Nm
- Wheel Lug NutsTorque in star pattern118 lb-ft160 Nm
Tune-Up - Major2 specs
- Air Box Clips4 lb-ft5 Nm
- Oil Drain PlugUse new crush washer26 lb-ft35 Nm
Tune-Up - Minor2 specs
- Air Box Clips4 lb-ft5 Nm
- Oil Drain PlugUse new crush washer26 lb-ft35 Nm
Wheel Alignment7 specs
- Air Box Clips4 lb-ft5 Nm
- Cam BoltsAfter adjustment95 lb-ft129 Nm
- Camber BoltsIf adjustable55 lb-ft75 Nm
- Oil Drain PlugUse new crush washer18 lb-ft25 Nm
- Tie Rod Jam Nuts41 lb-ft55 Nm
- Tie Rod Lock NutAfter adjustment50 lb-ft68 Nm
- Wheel Lug NutsTorque in star pattern118 lb-ft160 Nm
Brakes
ABS Module5 specs
- ABS Module Bolts7 lb-ft10 Nm
- Bleeder Screw11.8 lb-ft16 Nm
- Brake Line FittingsUse flare nut wrench11 lb-ft15 Nm
- Caliper Mounting Bolts75 lb-ft101 Nm
- Wheel Lug Nuts105 lb-ft142.4 Nm
ABS Pump4 specs
- Bleeder ScrewDo not overtighten12.5 lb-ft17 Nm
- Caliper Bracket Bolts - FrontThreadlocker recommended88 lb-ft120 Nm
- Caliper Mounting Bolts75 lb-ft101 Nm
- Wheel Lug NutsTorque in star pattern118 lb-ft160 Nm
ABS Tone Ring5 specs
- Bleeder ScrewDo not overtighten12.5 lb-ft17 Nm
- Caliper Bracket Bolts - FrontThreadlocker recommended88 lb-ft120 Nm
- Caliper Mounting Bolts75 lb-ft101 Nm
- Caliper Slide Pin BoltsApply silicone brake grease26 lb-ft35 Nm
- Wheel Lug NutsTorque in star pattern118 lb-ft160 Nm
ABS Wheel Speed Sensor - Front5 specs
- ABS Sensor BoltDo not overtighten5.9 lb-ft8 Nm
- Bleeder Screw11.8 lb-ft16 Nm
- Caliper Mounting Bolts75 lb-ft101 Nm
- Wheel Bearing Hub Bolts81 lb-ft110 Nm
- Wheel Lug Nuts105 lb-ft142.4 Nm
ABS Wheel Speed Sensor - Rear4 specs
- ABS Sensor BoltDo not overtighten5.9 lb-ft8 Nm
- Bleeder Screw11.8 lb-ft16 Nm
- Caliper Mounting Bolts75 lb-ft101 Nm
- Wheel Lug Nuts105 lb-ft142.4 Nm
Brake Bleed - All Four3 specs
- Bleeder ScrewDo not overtighten. Verify sequence with the service manual12.5 lb-ft17 Nm
- Caliper Mounting Bolts75 lb-ft101 Nm
- Wheel Lug NutsTorque in star pattern. Verify sequence with the service manual118 lb-ft160 Nm
Brake Booster6 specs
- Bleeder Screw11.8 lb-ft16 Nm
- Brake Booster NutsVerify sequence with the service manual18 lb-ft25 Nm
- Brake Pedal Pushrod LockVerify sequence with the service manual11 lb-ft15 Nm
- Caliper Mounting Bolts75 lb-ft101 Nm
- Master Cylinder NutsVerify sequence with the service manual18 lb-ft25 Nm
- Wheel Lug Nuts105 lb-ft142.4 Nm
Brake Booster Check Valve2 specs
- Bleeder ScrewDo not overtighten. Verify sequence with the service manual12.5 lb-ft17 Nm
- Caliper Mounting Bolts75 lb-ft101 Nm
Brake Caliper - Front3 specs
- Bleeder ScrewDo not overtighten12.5 lb-ft17 Nm
- Brake Line Banjo BoltUse new copper washers18 lb-ft25 Nm
- Caliper Bracket BoltsThreadlocker recommended88 lb-ft120 Nm
Brake Caliper - Rear3 specs
- Bleeder ScrewDo not overtighten12.5 lb-ft17 Nm
- Brake Line Banjo BoltUse new copper washers18 lb-ft25 Nm
- Caliper Bracket BoltsThreadlocker recommended74 lb-ft100 Nm
Brake Caliper Bracket6 specs
- Bleeder ScrewDo not overtighten. Verify sequence with the service manual12.5 lb-ft17 Nm
- Brake Hose Banjo BoltNew copper washers35 lb-ft47 Nm
- Caliper Bracket Bolts - FrontThreadlocker recommended. Verify sequence with the service manual88 lb-ft120 Nm
- Caliper Mounting Bolts75 lb-ft101 Nm
- Caliper Slide Pin BoltsApply silicone brake grease. Verify sequence with the service manual26 lb-ft35 Nm
- Wheel Lug NutsTorque in star pattern. Verify sequence with the service manual118 lb-ft160 Nm
Brake Caliper Rebuild - Front5 specs
- Bleeder ScrewDo not overtighten12.5 lb-ft17 Nm
- Caliper Bracket Bolts - FrontThreadlocker recommended88 lb-ft120 Nm
- Caliper Mounting Bolts75 lb-ft101 Nm
- Caliper Slide Pin BoltsApply silicone brake grease26 lb-ft35 Nm
- Wheel Lug NutsTorque in star pattern118 lb-ft160 Nm
Brake Caliper Rebuild - Rear4 specs
- Bleeder ScrewDo not overtighten12.5 lb-ft17 Nm
- Caliper Mounting Bolts75 lb-ft101 Nm
- Caliper Slide Pin BoltsApply silicone brake grease26 lb-ft35 Nm
- Wheel Lug NutsTorque in star pattern118 lb-ft160 Nm
Brake Caliper Slide Pins5 specs
- Bleeder ScrewDo not overtighten12.5 lb-ft17 Nm
- Caliper Bracket Bolts - FrontThreadlocker recommended88 lb-ft120 Nm
- Caliper Mounting Bolts75 lb-ft101 Nm
- Caliper Slide Pin BoltsApply silicone brake grease26 lb-ft35 Nm
- Wheel Lug NutsTorque in star pattern118 lb-ft160 Nm
Brake Fluid Flush6 specs
- Air Box ClipsVerify sequence with the service manual4 lb-ft5 Nm
- Bleeder ScrewDo not overtighten. Verify sequence with the service manual12.5 lb-ft17 Nm
- Caliper Bracket Bolts - FrontThreadlocker recommended. Verify sequence with the service manual88 lb-ft120 Nm
- Caliper Mounting Bolts75 lb-ft101 Nm
- Oil Drain PlugUse new crush washer. Verify sequence with the service manual18 lb-ft25 Nm
- Wheel Lug NutsTorque in star pattern. Verify sequence with the service manual118 lb-ft160 Nm
Brake Hose - Front5 specs
- Bleeder Screw11.8 lb-ft16 Nm
- Brake Hose Banjo BoltUse new copper washers. Verify sequence with the service manual18 lb-ft25 Nm
- Brake Hose BracketVerify sequence with the service manual7 lb-ft10 Nm
- Caliper Mounting Bolts75 lb-ft101 Nm
- Wheel Lug Nuts105 lb-ft142.4 Nm
Brake Hose - Rear5 specs
- Bleeder Screw11.8 lb-ft16 Nm
- Brake Hose Banjo BoltUse new copper washers. Verify sequence with the service manual18 lb-ft25 Nm
- Brake Hose BracketVerify sequence with the service manual7 lb-ft10 Nm
- Caliper Mounting Bolts75 lb-ft101 Nm
- Wheel Lug Nuts105 lb-ft142.4 Nm
Brake Light Switch3 specs
- Bleeder ScrewDo not overtighten. Verify sequence with the service manual12.5 lb-ft17 Nm
- Caliper Bracket Bolts - FrontThreadlocker recommended. Verify sequence with the service manual88 lb-ft120 Nm
- Caliper Mounting Bolts75 lb-ft101 Nm
Brake Line - Single4 specs
- Bleeder ScrewDo not overtighten. Verify sequence with the service manual12.5 lb-ft17 Nm
- Caliper Bracket Bolts - FrontThreadlocker recommended. Verify sequence with the service manual88 lb-ft120 Nm
- Caliper Mounting Bolts75 lb-ft101 Nm
- Wheel Lug NutsTorque in star pattern. Verify sequence with the service manual118 lb-ft160 Nm
Brake Lines - Complete Set4 specs
- Bleeder ScrewDo not overtighten. Verify sequence with the service manual12.5 lb-ft17 Nm
- Caliper Bracket Bolts - FrontThreadlocker recommended. Verify sequence with the service manual88 lb-ft120 Nm
- Caliper Mounting Bolts75 lb-ft101 Nm
- Wheel Lug NutsTorque in star pattern. Verify sequence with the service manual118 lb-ft160 Nm
Brake Master Cylinder2 specs
- Brake Line FittingsUse flare nut wrench11 lb-ft15 Nm
- Master Cylinder Nuts18 lb-ft25 Nm
Brake Master Cylinder Rebuild3 specs
- Brake Line FittingsUse flare nut wrench11 lb-ft15 Nm
- Master Cylinder Mounting Nuts18 lb-ft25 Nm
- Reservoir Mounting Bolts3.7 lb-ft5 Nm
Brake Pads - Front3 specs
- Caliper Bracket BoltsThreadlocker recommended88 lb-ft120 Nm
- Caliper Slide Pin BoltsApply silicone brake grease26 lb-ft35 Nm
- Wheel Lug NutsTorque in star pattern118 lb-ft160 Nm
Brake Pads - Rear3 specs
- Caliper Bracket BoltsThreadlocker recommended74 lb-ft100 Nm
- Caliper Slide Pin BoltsApply silicone brake grease22 lb-ft30 Nm
- Wheel Lug NutsTorque in star pattern118 lb-ft160 Nm
Brake Pads and Rotors - Front7 specs
- Bleeder ScrewDo not overtighten. Verify sequence with the service manual12.5 lb-ft17 Nm
- Caliper Bracket BoltsUse thread locker86 lb-ft117 Nm
- Caliper Bracket Bolts - FrontThreadlocker recommended. Verify sequence with the service manual88 lb-ft120 Nm
- Caliper Mounting Bolts75 lb-ft101 Nm
- Caliper Slide BoltsLubricate pins29 lb-ft39 Nm
- Caliper Slide Pin BoltsApply silicone brake grease. Verify sequence with the service manual26 lb-ft35 Nm
- Wheel Lug NutsTorque in star pattern. Verify sequence with the service manual118 lb-ft160 Nm
Brake Pads and Rotors - Rear6 specs
- Bleeder ScrewDo not overtighten. Verify sequence with the service manual12.5 lb-ft17 Nm
- Caliper Bracket BoltsUse thread locker86 lb-ft117 Nm
- Caliper Mounting Bolts75 lb-ft101 Nm
- Caliper Slide BoltsLubricate pins29 lb-ft39 Nm
- Caliper Slide Pin BoltsApply silicone brake grease. Verify sequence with the service manual26 lb-ft35 Nm
- Wheel Lug NutsTorque in star pattern. Verify sequence with the service manual118 lb-ft160 Nm
Brake Proportioning Valve5 specs
- Bleeder Screw11.8 lb-ft16 Nm
- Brake Line FittingsUse flare nut wrench. Verify sequence with the service manual11 lb-ft15 Nm
- Caliper Mounting Bolts75 lb-ft101 Nm
- Proportioning Valve BoltsVerify sequence with the service manual11 lb-ft15 Nm
- Wheel Lug Nuts115 lb-ft156 Nm
Brake Rotor - Front Single8 specs
- Bleeder ScrewDo not overtighten. Verify sequence with the service manual12.5 lb-ft17 Nm
- Brake Rotor Set Screw6 lb-ft8 Nm
- Caliper Bracket Bolts86 lb-ft117 Nm
- Caliper Bracket Bolts - FrontThreadlocker recommended. Verify sequence with the service manual88 lb-ft120 Nm
- Caliper Mounting Bolts75 lb-ft101 Nm
- Caliper Slide Pin BoltsApply silicone brake grease. Verify sequence with the service manual26 lb-ft35 Nm
- Hub NutIf removed207 lb-ft281 Nm
- Wheel Lug NutsTorque in star pattern. Verify sequence with the service manual118 lb-ft160 Nm
Brake Rotor - Rear Single7 specs
- Bleeder ScrewDo not overtighten. Verify sequence with the service manual12.5 lb-ft17 Nm
- Brake Rotor Set Screw6 lb-ft8 Nm
- Caliper Bracket Bolts86 lb-ft117 Nm
- Caliper Mounting Bolts75 lb-ft101 Nm
- Caliper Slide Pin BoltsApply silicone brake grease. Verify sequence with the service manual26 lb-ft35 Nm
- Hub NutIf removed207 lb-ft281 Nm
- Wheel Lug NutsTorque in star pattern. Verify sequence with the service manual118 lb-ft160 Nm
Brake Rotors - Front Pair8 specs
- Bleeder ScrewDo not overtighten. Verify sequence with the service manual12.5 lb-ft17 Nm
- Brake Rotor Set Screw6 lb-ft8 Nm
- Caliper Bracket Bolts86 lb-ft117 Nm
- Caliper Bracket Bolts - FrontThreadlocker recommended. Verify sequence with the service manual88 lb-ft120 Nm
- Caliper Mounting Bolts75 lb-ft101 Nm
- Caliper Slide Pin BoltsApply silicone brake grease. Verify sequence with the service manual26 lb-ft35 Nm
- Hub NutIf removed207 lb-ft281 Nm
- Wheel Lug NutsTorque in star pattern. Verify sequence with the service manual118 lb-ft160 Nm
Brake Rotors - Rear Pair7 specs
- Bleeder ScrewDo not overtighten. Verify sequence with the service manual12.5 lb-ft17 Nm
- Brake Rotor Set Screw6 lb-ft8 Nm
- Caliper Bracket Bolts86 lb-ft117 Nm
- Caliper Mounting Bolts75 lb-ft101 Nm
- Caliper Slide Pin BoltsApply silicone brake grease. Verify sequence with the service manual26 lb-ft35 Nm
- Hub NutIf removed207 lb-ft281 Nm
- Wheel Lug NutsTorque in star pattern. Verify sequence with the service manual118 lb-ft160 Nm
Electronic Parking Brake Motor5 specs
- Bleeder ScrewDo not overtighten. Verify sequence with the service manual12.5 lb-ft17 Nm
- Caliper Bracket Bolts - FrontThreadlocker recommended. Verify sequence with the service manual88 lb-ft120 Nm
- Caliper Mounting Bolts75 lb-ft101 Nm
- Caliper Slide Pin BoltsApply silicone brake grease. Verify sequence with the service manual26 lb-ft35 Nm
- Wheel Lug NutsTorque in star pattern. Verify sequence with the service manual118 lb-ft160 Nm
Front Brake Pad Replacement3 specs
- Caliper Bracket BoltsThreadlocker recommended88 lb-ft120 Nm
- Caliper Slide Pin BoltsApply silicone brake grease26 lb-ft35 Nm
- Wheel Lug NutsTorque in star pattern118 lb-ft160 Nm
Parking Brake Actuator5 specs
- Bleeder ScrewDo not overtighten. Verify sequence with the service manual12.5 lb-ft17 Nm
- Caliper Bracket Bolts - FrontThreadlocker recommended. Verify sequence with the service manual88 lb-ft120 Nm
- Caliper Mounting Bolts75 lb-ft101 Nm
- Caliper Slide Pin BoltsApply silicone brake grease. Verify sequence with the service manual26 lb-ft35 Nm
- Wheel Lug NutsTorque in star pattern. Verify sequence with the service manual118 lb-ft160 Nm
Parking Brake Cable5 specs
- Bleeder Screw11.8 lb-ft16 Nm
- Cable Bracket BoltsVerify sequence with the service manual9 lb-ft12 Nm
- Caliper Mounting Bolts75 lb-ft101 Nm
- Equalizer NutAdjust for proper tension. Verify sequence with the service manual11 lb-ft15 Nm
- Wheel Lug Nuts115 lb-ft156 Nm
Parking Brake Shoes5 specs
- Adjuster LockVerify sequence with the service manual4 lb-ft5 Nm
- Bleeder Screw11.8 lb-ft16 Nm
- Caliper Mounting Bolts75 lb-ft101 Nm
- Hold-Down SpringsVerify sequence with the service manual6 lb-ft8 Nm
- Wheel Lug NutsTorque in star pattern. Verify sequence with the service manual118 lb-ft160 Nm
Engine
Boost Pressure Sensor1 spec
- Boost Sensor7.4 lb-ft10 Nm
Camshaft Position Sensor2 specs
- Camshaft Position Sensor7.4 lb-ft10 Nm
- Valve Cover BoltsTighten in sequence7.4 lb-ft10 Nm
Camshaft R&R17 specs
- Cam Phaser BoltApply threadlocker, hold cam stationary36.9 lb-ft50 Nm
- Camshaft Bearing Cap BoltsTighten in sequence, 3 passes10 lb-ft14 Nm
- Camshaft Cap BoltsTighten in sequence from center outward, multiple passes10 lb-ft14 Nm
- Camshaft Position Sensor7.4 lb-ft10 Nm
- Camshaft Sprocket BoltsHold cam with wrench on hex59 lb-ft80 Nm
- Crankshaft Position Sensor7.4 lb-ft10 Nm
- Crankshaft Pulley BoltOften TTY - check spec, may require impact18.4 lb-ft25 Nm
- Oil Drain PlugUse new crush washer26 lb-ft35 Nm
- Rocker Arm BoltsTighten with cam lobe pointing away22 lb-ft30 Nm
- Rocker Arm Shaft BoltsTighten evenly in sequence7.4 lb-ft10 Nm
- Timing Chain Guide BoltsReplace if worn19.9 lb-ft27 Nm
- Timing Chain Idler Sprocket18 lb-ft25 Nm
- Timing Chain Tensioner BoltInstall with pin/clip to compress19.9 lb-ft27 Nm
- Timing Cover Bolts - 10mmTighten in sequence33 lb-ft45 Nm
- Timing Cover Bolts - 8mmTighten in sequence18 lb-ft25 Nm
- Valve Cover BoltsTighten in sequence7.4 lb-ft10 Nm
- VVT Solenoid Bolt4.4 lb-ft6 Nm
Connecting Rod Bearings3 specs
- Connecting Rod BoltsTTY - critical torque plus angle18 lb-ft25 Nm
- Oil Drain PlugUse new crush washer26 lb-ft35 Nm
- Oil Pan BoltTighten in sequence9 lb-ft12 Nm
Crankshaft Position Sensor1 spec
- Crankshaft Position Sensor7.4 lb-ft10 Nm
Crankshaft R&R17 specs
- Connecting Rod BoltsTTY - critical torque plus angle33 lb-ft45 Nm
- Crankshaft Pulley BoltOften TTY, may need impact18.4 lb-ft25 Nm
- Cylinder Head BoltsTTY - tighten in sequence plus angle33.2 lb-ft45 Nm
- Flexplate BoltsAutomatic transmissions63 lb-ft85 Nm
- Flywheel BoltsOften TTY, tighten in star pattern66.4 lb-ft90 Nm
- Front Main Seal Housing9 lb-ft12 Nm
- Main Bearing Cap BoltsTTY - tighten in sequence plus angle40.6 lb-ft55 Nm
- Oil Drain PlugUse new crush washer26 lb-ft35 Nm
- Oil Pan BoltTighten in sequence9 lb-ft12 Nm
- Oil Pump Bolts9 lb-ft12 Nm
- Oil Pump Pickup Tube9 lb-ft12 Nm
- Rear Main Seal Housing9 lb-ft12 Nm
- Timing Chain Guide BoltsReplace if worn7.4 lb-ft10 Nm
- Timing Chain Tensioner BoltInstall with pin/clip to compress7.4 lb-ft10 Nm
- Timing Cover Bolts - 10mmTighten in sequence33 lb-ft45 Nm
- Timing Cover Bolts - 8mmTighten in sequence18 lb-ft25 Nm
- Transmission-to-Engine Bolts41 lb-ft55 Nm
Cylinder Head R&R14 specs
- Camshaft Bearing Cap BoltsTighten in sequence, 3 passes10 lb-ft14 Nm
- Camshaft Cap BoltsTighten in sequence from center outward, multiple passes10 lb-ft14 Nm
- Camshaft Sprocket BoltsHold cam with wrench on hex36.9 lb-ft50 Nm
- Cylinder Head BoltsTTY - tighten in sequence plus angle48 lb-ft65 Nm
- Exhaust Manifold NutsApply anti-seize, work hot-to-cold25.8 lb-ft35 Nm
- Intake Manifold Bolt18 lb-ft25 Nm
- Oil Drain PlugUse new crush washer26 lb-ft35 Nm
- Rocker Arm BoltsTighten with cam lobe pointing away7.4 lb-ft10 Nm
- Rocker Arm Shaft BoltsTighten evenly in sequence18 lb-ft25 Nm
- Thermostat Housing Bolt7.4 lb-ft10 Nm
- Timing Chain Guide BoltsReplace if worn7.4 lb-ft10 Nm
- Timing Chain Tensioner BoltInstall with pin/clip to compress18 lb-ft25 Nm
- Timing Cover Bolts - 8mmTighten in sequence18 lb-ft25 Nm
- Valve Cover BoltsTighten in sequence7.4 lb-ft10 Nm
Cylinder Head Resurface4 specs
- Cylinder Head BoltsTTY - tighten in sequence plus angle48 lb-ft65 Nm
- Exhaust Manifold NutsApply anti-seize, work hot-to-cold25.8 lb-ft35 Nm
- Intake Manifold Bolt18 lb-ft25 Nm
- Valve Cover BoltsTighten in sequence7.4 lb-ft10 Nm
Engine Mount - Front3 specs
- Engine Mount Through-Bolt63 lb-ft85 Nm
- Engine Mount-to-Block Bolts73.8 lb-ft100 Nm
- Engine Mount-to-Frame Bolts55 lb-ft75 Nm
Engine Mount - Rear3 specs
- Engine Mount Through-Bolt75 lb-ft101 Nm
- Engine Mount-to-Block Bolts73.8 lb-ft100 Nm
- Engine Mount-to-Frame Bolts52 lb-ft70 Nm
Engine Mounts - All4 specs
- Engine Mount Through-Bolt75 lb-ft101 Nm
- Engine Mount-to-Block Bolts48 lb-ft65 Nm
- Engine Mount-to-Frame Bolts52 lb-ft70 Nm
- Transmission Mount Bolts48 lb-ft65 Nm
Engine R&R10 specs
- AC Compressor Bolts18 lb-ft25 Nm
- Alternator Mounting Bolts18 lb-ft25 Nm
- Engine Mount-to-Block Bolts48 lb-ft65 Nm
- Engine Mount-to-Frame Bolts55 lb-ft75 Nm
- Exhaust Manifold NutsApply anti-seize, work hot-to-cold25.8 lb-ft35 Nm
- Flywheel BoltsOften TTY, tighten in star pattern70 lb-ft95 Nm
- Oil Drain PlugUse new crush washer18 lb-ft25 Nm
- Power Steering Pump Bolts18 lb-ft25 Nm
- Starter Mounting Bolt22.1 lb-ft30 Nm
- Transmission-to-Engine Bolts41 lb-ft55 Nm
Engine Rebuild18 specs
- Balance Shaft Bolts18 lb-ft25 Nm
- Camshaft Bearing Cap BoltsTighten in sequence, 3 passes10 lb-ft14 Nm
- Camshaft Cap BoltsTighten in sequence from center outward, multiple passes10 lb-ft14 Nm
- Connecting Rod BoltsTTY - critical torque plus angle33 lb-ft45 Nm
- Crankshaft Pulley BoltOften TTY - check spec, may require impact133 lb-ft180 Nm
- Cylinder Head BoltsTTY - tighten in sequence plus angle33.2 lb-ft45 Nm
- Exhaust Manifold NutsApply anti-seize, work hot-to-cold25.8 lb-ft35 Nm
- Flywheel BoltsOften TTY, tighten in star pattern70 lb-ft95 Nm
- Intake Manifold Bolt18 lb-ft25 Nm
- Main Bearing Cap BoltsTTY - tighten in sequence plus angle40.6 lb-ft55 Nm
- Oil Drain PlugUse new crush washer26 lb-ft35 Nm
- Oil Pan BoltTighten in sequence9 lb-ft12 Nm
- Oil Pump Bolts9 lb-ft12 Nm
- Oil Pump Pickup Tube9 lb-ft12 Nm
- Timing Chain Guide BoltsReplace if worn19.9 lb-ft27 Nm
- Timing Chain Tensioner BoltInstall with pin/clip to compress7.4 lb-ft10 Nm
- Timing Cover Bolts - 8mmTighten in sequence18 lb-ft25 Nm
- Valve Cover BoltsTighten in sequence7.4 lb-ft10 Nm
Exhaust Manifold5 specs
- Exhaust Flange BoltApply anti-seize. Verify sequence with the service manual18 lb-ft25 Nm
- Exhaust Manifold NutsApply anti-seize, work hot-to-cold. Verify sequence with the service manual25.8 lb-ft35 Nm
- Hanger Bolts17 lb-ft23 Nm
- Heat Shield BoltsVerify sequence with the service manual7.4 lb-ft10 Nm
- O2 SensorAnti-seize threads40 lb-ft55 Nm
Exhaust Manifold Gasket3 specs
- Exhaust Manifold NutsApply anti-seize, work hot-to-cold25.8 lb-ft35 Nm
- Exhaust Manifold StudsIf replacing studs11 lb-ft15 Nm
- Heat Shield Bolts7.4 lb-ft10 Nm
Fan Belt Replacement3 specs
- Idler Pulley Bolt30 lb-ft40 Nm
- Tensioner Bolt18 lb-ft25 Nm
- Tensioner Pulley Bolt33 lb-ft45 Nm
Flexplate3 specs
- Flexplate BoltsAutomatic transmissions. Verify sequence with the service manual63 lb-ft85 Nm
- Torque Converter BoltsVerify sequence with the service manual37 lb-ft50 Nm
- Transmission-to-Engine BoltsVerify sequence with the service manual41 lb-ft55 Nm
Freeze Plug - Single1 spec
- Freeze PlugUse sealant on edges7 lb-ft10 Nm
Freeze Plugs - All1 spec
- Freeze PlugUse sealant on edges7 lb-ft10 Nm
Front Main Seal5 specs
- Crankshaft Pulley BoltOften TTY, may need impact18.4 lb-ft25 Nm
- Oil Drain PlugUse new crush washer26 lb-ft35 Nm
- Oil Pan BoltFront section only9 lb-ft12 Nm
- Timing Cover Bolts - 10mmTighten in sequence33 lb-ft45 Nm
- Timing Cover Bolts - 8mmTighten in sequence18 lb-ft25 Nm
Full Engine Tune-Up4 specs
- Ignition Coil Bolt4.4 lb-ft6 Nm
- Spark Plugs - Aluminum HeadApply anti-seize to threads13.3 lb-ft18 Nm
- Throttle Body Bolts7.4 lb-ft10 Nm
- Valve Cover BoltsTighten in sequence7.4 lb-ft10 Nm
Harmonic Balancer1 spec
- Crankshaft Pulley BoltOften TTY - check spec, may require impact. Verify sequence with the service manual18.4 lb-ft25 Nm
Head Gasket - Single6 specs
- Exhaust Manifold NutsApply anti-seize25.8 lb-ft35 Nm
- Intake Manifold BoltTighten in sequence7.4 lb-ft10 Nm
- Cylinder Head Bolts - Step 1Always use new TTY bolts30 lb-ft40 Nm
- Cylinder Head Bolts - Step 2Tighten in sequence59 lb-ft80 Nm
- Cylinder Head Bolts - Step 3Plus 90 degreesTurn 90°
- Cylinder Head Bolts - Step 4Plus 90 degrees63 lb-ft + 90°85 Nm
Head Gaskets - Both13 specs
- Camshaft Cap BoltsTighten in sequence from center outward, multiple passes10 lb-ft14 Nm
- Camshaft Sprocket BoltsHold cam with wrench on hex36.9 lb-ft50 Nm
- Crankshaft Pulley BoltOften TTY - check spec, may require impact18.4 lb-ft25 Nm
- Cylinder Head BoltsMulti-step + angle75 lb-ft101 Nm
- Exhaust Manifold Nuts25.8 lb-ft35 Nm
- Intake Manifold Bolt8 lb-ft11 Nm
- Oil Drain PlugUse new crush washer26 lb-ft35 Nm
- Rocker Arm BoltsTighten with cam lobe pointing away7.4 lb-ft10 Nm
- Sensor Mounting Bolts7 lb-ft10 Nm
- Timing Chain Tensioner BoltInstall with pin/clip to compress7.4 lb-ft10 Nm
- Timing Cover Bolts - 8mmTighten in sequence18 lb-ft25 Nm
- Valve Cover BoltsTighten in sequence7.4 lb-ft10 Nm
- VVT Solenoid Bolt4.4 lb-ft6 Nm
Idle Air Control Valve1 spec
- IAC Valve Screws2 lb-ft3 Nm
Idler Pulley1 spec
- Idler Pulley Bolt33 lb-ft45 Nm
Intake Manifold4 specs
- Fuel Rail BoltsVerify sequence with the service manual7.4 lb-ft10 Nm
- Intake Manifold BoltTighten in sequence from center out. Verify sequence with the service manual18 lb-ft25 Nm
- PCV ValveVerify sequence with the service manual6 lb-ft8 Nm
- Throttle Body BoltsVerify sequence with the service manual7.4 lb-ft10 Nm
Intake Manifold Gasket3 specs
- Fuel Rail Bolts7.4 lb-ft10 Nm
- Intake Manifold BoltTighten in sequence from center out18 lb-ft25 Nm
- Throttle Body Bolts7.4 lb-ft10 Nm
Intercooler2 specs
- Charge Pipe Clamps3 lb-ft4 Nm
- Intercooler Mounting Bolts11 lb-ft15 Nm
Knock Sensor1 spec
- Knock SensorTorque critical for function14.8 lb-ft20 Nm
Lifter - Single4 specs
- Intake Manifold Bolt7.4 lb-ft10 Nm
- Rocker Arm BoltsTighten with cam lobe pointing away22 lb-ft30 Nm
- Rocker Arm Shaft BoltsTighten evenly in sequence18 lb-ft25 Nm
- Valve Cover BoltsTighten in sequence7.4 lb-ft10 Nm
Lifters/Tappets - All7 specs
- Camshaft Bearing Cap BoltsTighten in sequence, 3 passes10 lb-ft14 Nm
- Camshaft Cap BoltsTighten in sequence from center outward, multiple passes10 lb-ft14 Nm
- Camshaft Position Sensor7.4 lb-ft10 Nm
- Intake Manifold Bolt7.4 lb-ft10 Nm
- Rocker Arm BoltsTighten with cam lobe pointing away22 lb-ft30 Nm
- Rocker Arm Shaft BoltsTighten evenly in sequence18 lb-ft25 Nm
- Valve Cover BoltsTighten in sequence7.4 lb-ft10 Nm
Long Block Replacement13 specs
- Camshaft Cap BoltsTighten in sequence from center outward, multiple passes10 lb-ft14 Nm
- Connecting Rod BoltsTTY - critical torque plus angle33 lb-ft45 Nm
- Cylinder Head BoltsTTY - tighten in sequence plus angle33.2 lb-ft45 Nm
- Exhaust Manifold NutsApply anti-seize, work hot-to-cold25.8 lb-ft35 Nm
- Flywheel BoltsOften TTY, tighten in star pattern70 lb-ft95 Nm
- Intake Manifold Bolt18 lb-ft25 Nm
- Main Bearing Cap BoltsTTY - tighten in sequence plus angle55 lb-ft75 Nm
- Oil Drain PlugUse new crush washer26 lb-ft35 Nm
- Oil Pan Bolt9 lb-ft12 Nm
- Timing Chain Tensioner BoltInstall with pin/clip to compress18 lb-ft25 Nm
- Timing Cover Bolts - 8mmTighten in sequence18 lb-ft25 Nm
- Transmission-to-Engine Bolts41 lb-ft55 Nm
- Valve Cover BoltsTighten in sequence7.4 lb-ft10 Nm
Main Bearings6 specs
- Flywheel BoltsOften TTY, tighten in star pattern. Verify sequence with the service manual70 lb-ft95 Nm
- Main Bearing Cap BoltsTTY - tighten in sequence plus angle. Verify sequence with the service manual55 lb-ft75 Nm
- Oil Drain PlugUse new crush washer. Verify sequence with the service manual26 lb-ft35 Nm
- Oil Pan BoltTighten in sequence. Verify sequence with the service manual9 lb-ft12 Nm
- Oil Pump Pickup TubeVerify sequence with the service manual9 lb-ft12 Nm
- Transmission-to-Engine BoltsVerify sequence with the service manual41 lb-ft55 Nm
Manifold Absolute Pressure Sensor1 spec
- MAP Sensor Screws7.4 lb-ft10 Nm
Mass Air Flow Sensor2 specs
- Air Intake Clamps2 lb-ft3 Nm
- MAF Sensor Screws2.2 lb-ft3 Nm
Oil Change2 specs
- Oil Drain PlugUse new crush washer26 lb-ft35 Nm
- Oil Filter Housing CapFor cartridge-type filters18.4 lb-ft25 Nm
Oil Level Sensor2 specs
- Oil Level Sensor28 lb-ft38 Nm
- Oil Pan BoltIf access needed9 lb-ft12 Nm
Oil Pan Gasket2 specs
- Oil Drain PlugUse new crush washer26 lb-ft35 Nm
- Oil Pan BoltTighten in sequence from center outward9 lb-ft12 Nm
Oil Pan Replacement3 specs
- Oil Drain PlugUse new crush washer26 lb-ft35 Nm
- Oil Pan BoltTighten in sequence9 lb-ft12 Nm
- Oil Pump Pickup Tube9 lb-ft12 Nm
Oil Pressure Sensor1 spec
- Oil Pressure SensorUse thread sealant14.8 lb-ft20 Nm
Oil Pump5 specs
- Oil Drain PlugUse new crush washer26 lb-ft35 Nm
- Oil Pan Bolt9 lb-ft12 Nm
- Oil Pump Bolts9 lb-ft12 Nm
- Oil Pump Pickup Tube9 lb-ft12 Nm
- Timing Cover Bolts - 8mmTighten in sequence18 lb-ft25 Nm
PCV Valve1 spec
- PCV ValveHand tight usually6 lb-ft8 Nm
Piston - Single4 specs
- Connecting Rod BoltsTTY - critical torque plus angle15 lb-ft20 Nm
- Cylinder Head BoltsTTY - tighten in sequence plus angle48 lb-ft65 Nm
- Oil Drain PlugUse new crush washer26 lb-ft35 Nm
- Oil Pan Bolt9 lb-ft12 Nm
Piston Rings - All6 specs
- Connecting Rod BoltsTTY - critical torque plus angle15 lb-ft20 Nm
- Cylinder Head BoltsTTY - tighten in sequence plus angle48 lb-ft65 Nm
- Main Bearing Cap BoltsTTY - tighten in sequence plus angle40.6 lb-ft55 Nm
- Oil Drain PlugUse new crush washer26 lb-ft35 Nm
- Oil Pan BoltTighten in sequence9 lb-ft12 Nm
- Oil Pump Pickup Tube9 lb-ft12 Nm
Pistons - All6 specs
- Connecting Rod BoltsTTY - critical torque plus angle15 lb-ft20 Nm
- Cylinder Head BoltsTTY - tighten in sequence plus angle48 lb-ft65 Nm
- Main Bearing Cap BoltsTTY - tighten in sequence plus angle40.6 lb-ft55 Nm
- Oil Drain PlugUse new crush washer26 lb-ft35 Nm
- Oil Pan Bolt9 lb-ft12 Nm
- Oil Pump Pickup Tube9 lb-ft12 Nm
Rear Main Seal6 specs
- Flexplate BoltsAutomatic transmissions63 lb-ft85 Nm
- Flywheel BoltsOften TTY, tighten in star pattern70 lb-ft95 Nm
- Oil Drain PlugUse new crush washer26 lb-ft35 Nm
- Oil Pan BoltRear section9 lb-ft12 Nm
- Rear Main Seal Housing9 lb-ft12 Nm
- Transmission-to-Engine Bolts41 lb-ft55 Nm
Rocker Arms - All4 specs
- Intake Manifold BoltIf pushrods7.4 lb-ft10 Nm
- Rocker Arm BoltsTighten with cam lobe pointing away7.4 lb-ft10 Nm
- Rocker Arm Shaft BoltsTighten evenly in sequence18 lb-ft25 Nm
- Valve Cover BoltsTighten in sequence7.4 lb-ft10 Nm
Serpentine Belt2 specs
- Belt Tensioner Bolt41 lb-ft55 Nm
- Idler Pulley Bolt33 lb-ft45 Nm
Serpentine Belt Tensioner1 spec
- Belt Tensioner Bolt33 lb-ft45 Nm
Short Block Replacement9 specs
- Connecting Rod BoltsTTY - critical torque plus angle15 lb-ft20 Nm
- Crankshaft Pulley BoltOften TTY - check spec, may require impact133 lb-ft180 Nm
- Flywheel BoltsOften TTY, tighten in star pattern66.4 lb-ft90 Nm
- Main Bearing Cap BoltsTTY - tighten in sequence plus angle55 lb-ft75 Nm
- Oil Drain PlugUse new crush washer17.7 lb-ft24 Nm
- Oil Pan Bolt9 lb-ft12 Nm
- Oil Pump Bolts9 lb-ft12 Nm
- Timing Cover Bolts - 8mmTighten in sequence18 lb-ft25 Nm
- Transmission-to-Engine Bolts36.9 lb-ft50 Nm
Throttle Body2 specs
- Air Intake Hose Clamps2 lb-ft3 Nm
- Throttle Body Bolts7.4 lb-ft10 Nm
Throttle Position Sensor1 spec
- TPS Screws2 lb-ft3 Nm
Timing Chain5 specs
- Camshaft Sprocket Bolts36.9 lb-ft50 Nm
- Crankshaft Pulley BoltOften TTY - check specs133 lb-ft + 90°180 Nm
- Timing Chain Guide Bolts7.4 lb-ft10 Nm
- Timing Chain Tensioner33 lb-ft45 Nm
- Timing Cover BoltTighten in sequence7.4 lb-ft10 Nm
Timing Chain Guide8 specs
- Camshaft Sprocket Bolts63 lb-ft86 Nm
- Crankshaft Pulley Bolt150 lb-ft203 Nm
- Guide Bolts21 lb-ft28 Nm
- Tensioner Bolt33 lb-ft45 Nm
- Timing Chain Guide BoltsReplace if worn7.4 lb-ft10 Nm
- Timing Cover Bolt12 lb-ft16 Nm
- Timing Cover Bolts - 8mmTighten in sequence18 lb-ft25 Nm
- Valve Cover BoltsTighten in sequence7.4 lb-ft10 Nm
Timing Chain Kit15 specs
- Cam Phaser BoltApply threadlocker, hold cam stationary36.9 lb-ft50 Nm
- Camshaft Sprocket BoltsHold cam with wrench on hex59 lb-ft80 Nm
- Crankshaft Pulley BoltOften TTY - check spec, may require impact133 lb-ft180 Nm
- Guide Bolts21 lb-ft28 Nm
- Oil Drain PlugUse new crush washer26 lb-ft35 Nm
- Oil Pump Bolts9 lb-ft12 Nm
- Tensioner Bolt33 lb-ft45 Nm
- Timing Chain Guide BoltsReplace if worn7.4 lb-ft10 Nm
- Timing Chain Idler Sprocket81.1 lb-ft110 Nm
- Timing Chain Tensioner BoltInstall with pin/clip to compress18 lb-ft25 Nm
- Timing Cover Bolt12 lb-ft16 Nm
- Timing Cover Bolts - 10mmTighten in sequence33 lb-ft45 Nm
- Timing Cover Bolts - 6mmTighten in sequence7.4 lb-ft10 Nm
- Timing Cover Bolts - 8mmTighten in sequence18 lb-ft25 Nm
- Valve Cover BoltsTighten in sequence7.4 lb-ft10 Nm
Timing Chain Tensioner8 specs
- Camshaft Sprocket Bolts36.9 lb-ft50 Nm
- Crankshaft Pulley Bolt150 lb-ft203 Nm
- Guide Bolts21 lb-ft28 Nm
- Tensioner Bolt17 lb-ft23 Nm
- Timing Chain Tensioner BoltInstall with pin/clip to compress18 lb-ft25 Nm
- Timing Cover Bolt7.4 lb-ft10 Nm
- Timing Cover Bolts - 8mmTighten in sequence18 lb-ft25 Nm
- Valve Cover BoltsTighten in sequence7.4 lb-ft10 Nm
Transmission Mount5 specs
- Crossmember Bolt70 lb-ft95 Nm
- Flywheel BoltsOften TTY, tighten in star pattern70 lb-ft95 Nm
- Transmission Drain PlugUse new crush washer if equipped36.9 lb-ft50 Nm
- Transmission Mount Bolts48 lb-ft65 Nm
- Transmission Pan BoltsTighten in criss-cross pattern9 lb-ft12 Nm
Turbo Wastegate Actuator1 spec
- Wastegate Actuator Bolts2.2 lb-ft3 Nm
Turbocharger7 specs
- Coolant Line Fittings11 lb-ft15 Nm
- Exhaust Manifold NutsApply anti-seize, work hot-to-cold25.8 lb-ft35 Nm
- Heat Shield Bolts7.4 lb-ft10 Nm
- Oil Feed LineUse new crush washers15 lb-ft20 Nm
- Oil Return Line7.4 lb-ft10 Nm
- Turbo-to-Downpipe Bolts33 lb-ft45 Nm
- Turbo-to-Manifold BoltsApply anti-seize26 lb-ft35 Nm
Valve Adjustment3 specs
- Rocker Arm BoltsTighten with cam lobe pointing away22 lb-ft30 Nm
- Valve Cover BoltsTighten in sequence7.4 lb-ft10 Nm
- Valve Lash Adjusting Screw Lock NutHold screw while tightening15 lb-ft20 Nm
Valve Cover Gasket - Single2 specs
- Spark Plug Tube SealsIf equipped with separate seals9 lb-ft12 Nm
- Valve Cover BoltsTighten in sequence7.4 lb-ft10 Nm
Valve Cover Gaskets - Both4 specs
- Ignition Coil Bolt4.4 lb-ft6 Nm
- Intake Manifold BoltIf required7.4 lb-ft10 Nm
- Spark Plugs - Aluminum HeadApply anti-seize to threads18 lb-ft25 Nm
- Valve Cover BoltsTighten in sequence7.4 lb-ft10 Nm
Valve Job - Complete9 specs
- Camshaft Cap BoltsTighten in sequence from center outward, multiple passes10 lb-ft14 Nm
- Camshaft Sprocket BoltsHold cam with wrench on hex36.9 lb-ft50 Nm
- Cylinder Head BoltsTTY - tighten in sequence plus angle48 lb-ft65 Nm
- Exhaust Manifold NutsApply anti-seize, work hot-to-cold25.8 lb-ft35 Nm
- Intake Manifold Bolt18 lb-ft25 Nm
- Rocker Arm BoltsTighten with cam lobe pointing away22 lb-ft30 Nm
- Timing Chain Tensioner BoltInstall with pin/clip to compress7.4 lb-ft10 Nm
- Timing Cover Bolts - 8mmTighten in sequence18 lb-ft25 Nm
- Valve Cover BoltsTighten in sequence7.4 lb-ft10 Nm
Valve Seals5 specs
- Camshaft Cap BoltsTighten in sequence from center outward, multiple passes10 lb-ft14 Nm
- Rocker Arm BoltsTighten with cam lobe pointing away22 lb-ft30 Nm
- Rocker Arm Shaft BoltsTighten evenly in sequence18 lb-ft25 Nm
- Spark Plugs - Aluminum HeadApply anti-seize to threads18 lb-ft25 Nm
- Valve Cover BoltsTighten in sequence7.4 lb-ft10 Nm
Valve Spring - Single3 specs
- Rocker Arm BoltsTighten with cam lobe pointing away22 lb-ft30 Nm
- Spark Plugs - Aluminum HeadApply anti-seize to threads13.3 lb-ft18 Nm
- Valve Cover BoltsTighten in sequence7.4 lb-ft10 Nm
Valve Springs - All5 specs
- Camshaft Cap BoltsTighten in sequence from center outward, multiple passes10 lb-ft14 Nm
- Rocker Arm BoltsTighten with cam lobe pointing away22 lb-ft30 Nm
- Rocker Arm Shaft BoltsTighten evenly in sequence18 lb-ft25 Nm
- Spark Plugs - Aluminum HeadApply anti-seize to threads18 lb-ft25 Nm
- Valve Cover BoltsTighten in sequence7.4 lb-ft10 Nm
Variable Valve Timing Actuator7 specs
- Cam Phaser BoltApply threadlocker, hold cam stationary36.9 lb-ft50 Nm
- Camshaft Sprocket BoltsHold cam with wrench on hex48 lb-ft65 Nm
- Crankshaft Pulley BoltOften TTY - check spec, may require impact133 lb-ft180 Nm
- Timing Chain Tensioner BoltInstall with pin/clip to compress7.4 lb-ft10 Nm
- Timing Cover Bolts - 8mmTighten in sequence18 lb-ft25 Nm
- Valve Cover BoltsTighten in sequence7.4 lb-ft10 Nm
- VVT Solenoid Bolt4.4 lb-ft6 Nm
VVT Solenoid - Single2 specs
- Valve Cover BoltsTighten in sequence7.4 lb-ft10 Nm
- VVT Solenoid Bolt4.4 lb-ft6 Nm
VVT Solenoids - All3 specs
- Camshaft Position Sensor7.4 lb-ft10 Nm
- Valve Cover BoltsTighten in sequence7.4 lb-ft10 Nm
- VVT Solenoid Bolt4.4 lb-ft6 Nm
Cooling
Coolant Bypass Pipe7 specs
- Bleed ScrewOpen during fill6 lb-ft8 Nm
- Coolant Drain Plug11 lb-ft15 Nm
- Drain PetcockHand tight6 lb-ft8 Nm
- Hose Clamps2 lb-ft3 Nm
- Pump Bolts21 lb-ft28 Nm
- Thermostat Housing Bolt7.4 lb-ft10 Nm
- Water Pump BoltsTighten in criss-cross pattern7.4 lb-ft10 Nm
Coolant Flush10 specs
- Air Box Clips4 lb-ft5 Nm
- Bleed ScrewOpen during fill5 lb-ft7 Nm
- Block Drain PlugIf equipped, use new washer18 lb-ft25 Nm
- Coolant Hose Clamps3 lb-ft4 Nm
- Drain Petcock4 lb-ft5 Nm
- Drain Plug11 lb-ft15 Nm
- Hose Clamps3 lb-ft5 Nm
- Oil Drain PlugUse new crush washer26 lb-ft35 Nm
- Pump Bolts21 lb-ft28 Nm
- Wheel Lug NutsTorque in star pattern118 lb-ft160 Nm
Coolant Reservoir8 specs
- Bleed ScrewOpen during fill6 lb-ft8 Nm
- Coolant Drain Plug11 lb-ft15 Nm
- Drain PetcockHand tight6 lb-ft8 Nm
- Hose Clamps3 lb-ft5 Nm
- Pump Bolts21 lb-ft28 Nm
- Reservoir Mounting Bolts5.9 lb-ft8 Nm
- Thermostat Housing Bolt7.4 lb-ft10 Nm
- Water Pump BoltsTighten in criss-cross pattern7.4 lb-ft10 Nm
Coolant Temperature Sensor7 specs
- Bleed ScrewOpen during fill6 lb-ft8 Nm
- Coolant Drain Plug11 lb-ft15 Nm
- Drain PetcockHand tight6 lb-ft8 Nm
- Hose Clamps2 lb-ft3 Nm
- Pump Bolts21 lb-ft28 Nm
- Thermostat Housing Bolt7.4 lb-ft10 Nm
- Water Pump BoltsTighten in criss-cross pattern7.4 lb-ft10 Nm
Cooling Fan Assembly5 specs
- Coolant Drain Plug11 lb-ft15 Nm
- Hose Clamps2 lb-ft3 Nm
- Pump Bolts21 lb-ft28 Nm
- Thermostat Housing Bolt7.4 lb-ft10 Nm
- Water Pump BoltsTighten in criss-cross pattern7.4 lb-ft10 Nm
Cooling Fan Clutch4 specs
- Hose Clamps2 lb-ft3 Nm
- Pump Bolts21 lb-ft28 Nm
- Thermostat Housing Bolt7.4 lb-ft10 Nm
- Water Pump BoltsTighten in criss-cross pattern7.4 lb-ft10 Nm
Cooling Fan Motor4 specs
- Electrical Connector4 lb-ft5 Nm
- Fan Motor Bolts3 lb-ft4 Nm
- Hose Clamps3 lb-ft5 Nm
- Pump Bolts21 lb-ft28 Nm
Cooling Fan Relay2 specs
- Pump Bolts21 lb-ft28 Nm
- Thermostat Housing Bolt11 lb-ft15 Nm
Engine Oil Cooler5 specs
- Coolant Drain Plug11 lb-ft15 Nm
- Hose Clamps2 lb-ft3 Nm
- Pump Bolts21 lb-ft28 Nm
- Thermostat Housing Bolt7.4 lb-ft10 Nm
- Water Pump BoltsTighten in criss-cross pattern7.4 lb-ft10 Nm
Heater Control Valve3 specs
- Hose Clamps2 lb-ft3 Nm
- Pump Bolts21 lb-ft28 Nm
- Valve Mounting6 lb-ft8 Nm
Heater Core5 specs
- Dashboard Screws2 lb-ft3 Nm
- Heater Core Mounting6 lb-ft8 Nm
- Heater Hose Clamps2 lb-ft3 Nm
- Hose Clamps3 lb-ft5 Nm
- Pump Bolts21 lb-ft28 Nm
Heater Hoses5 specs
- Coolant Drain Plug11 lb-ft15 Nm
- Hose Clamps2 lb-ft3 Nm
- Pump Bolts21 lb-ft28 Nm
- Thermostat Housing Bolt7.4 lb-ft10 Nm
- Water Pump BoltsTighten in criss-cross pattern7.4 lb-ft10 Nm
Radiator4 specs
- Drain PetcockPlastic - hand tight4 lb-ft5 Nm
- Radiator Mounting BoltDo not overtighten plastic mounts3 lb-ft4 Nm
- Transmission Cooler LinesIf equipped18 lb-ft25 Nm
- Upper/Lower Hose Clamps2 lb-ft3 Nm
Radiator Cap3 specs
- Pump Bolts21 lb-ft28 Nm
- Thermostat Housing Bolt7.4 lb-ft10 Nm
- Water Pump BoltsTighten in criss-cross pattern7.4 lb-ft10 Nm
Radiator Hose - Lower2 specs
- Hose Clamps2 lb-ft3 Nm
- Pump Bolts21 lb-ft28 Nm
Radiator Hose - Upper2 specs
- Hose Clamps2 lb-ft3 Nm
- Pump Bolts21 lb-ft28 Nm
Radiator Hoses - Both5 specs
- Coolant Drain Plug11 lb-ft15 Nm
- Hose Clamps2 lb-ft3 Nm
- Pump Bolts21 lb-ft28 Nm
- Thermostat Housing Bolt7.4 lb-ft10 Nm
- Water Pump BoltsTighten in criss-cross pattern7.4 lb-ft10 Nm
Radiator Removal and Service4 specs
- Drain PetcockPlastic - hand-tight only4 lb-ft5 Nm
- Fan Shroud Bolts3 lb-ft4 Nm
- Radiator Mounting BoltDo not overtighten plastic mounts3 lb-ft4 Nm
- Transmission Cooler LinesIf equipped, use new washers5.9 lb-ft8 Nm
Thermostat2 specs
- Coolant Temperature SensorUse thread sealant14.8 lb-ft20 Nm
- Thermostat Housing Bolt7.4 lb-ft10 Nm
Thermostat Housing6 specs
- Coolant Drain Plug11 lb-ft15 Nm
- Coolant Hose Clamps3 lb-ft5 Nm
- Hose Clamps2 lb-ft3 Nm
- Pump Bolts21 lb-ft28 Nm
- Thermostat Housing Bolt7.4 lb-ft10 Nm
- Water Pump BoltsTighten in criss-cross pattern7.4 lb-ft10 Nm
Water Pump3 specs
- Hose ClampsSpring clamps preferred2 lb-ft3 Nm
- Thermostat Housing Bolt7.4 lb-ft10 Nm
- Water Pump BoltsTighten in criss-cross pattern7.4 lb-ft10 Nm
Ignition
Ignition Coil - Single2 specs
- Ignition Coil Bolt4.4 lb-ft6 Nm
- Spark Plugs - Aluminum HeadApply anti-seize to threads13.3 lb-ft18 Nm
Ignition Coils - All2 specs
- Ignition Coil Bolt4.4 lb-ft6 Nm
- Spark Plugs - Aluminum HeadApply anti-seize to threads13.3 lb-ft18 Nm
Ignition Control Module2 specs
- Ignition Coil Bolt6 lb-ft8 Nm
- Spark Plugs - Aluminum HeadApply anti-seize to threads18 lb-ft25 Nm
Ignition Lock Cylinder2 specs
- Ignition Coil Bolt6 lb-ft8 Nm
- Spark Plugs - Aluminum HeadApply anti-seize to threads18 lb-ft25 Nm
Ignition Switch2 specs
- Steering Column Bolts22 lb-ft30 Nm
- Switch Mounting Screws4 lb-ft5 Nm
Spark Plugs7 specs
- Air Box Clips4 lb-ft5 Nm
- Engine Cover Clips2 lb-ft3 Nm
- Ignition Coil Bolt4.4 lb-ft6 Nm
- Oil Drain PlugUse new crush washer17.7 lb-ft24 Nm
- Spark PlugGap before install18 lb-ft25 Nm
- Spark Plugs - Aluminum HeadApply anti-seize to threads18 lb-ft24 Nm
- Wheel Lug NutsTorque in star pattern118 lb-ft160 Nm
Fuel system
Charcoal Canister3 specs
- Fuel Line FittingsUse new O-rings18 lb-ft25 Nm
- Fuel Rail Bolts7.4 lb-ft10 Nm
- Hose Clamps2 lb-ft3 Nm
EVAP Purge Valve1 spec
- Hose Clamps2 lb-ft3 Nm
EVAP Vent Valve1 spec
- Hose Clamps2 lb-ft3 Nm
Fuel Filler Neck3 specs
- Filler Neck Bolts3.7 lb-ft5 Nm
- Fuel Rail Bolts7 lb-ft10 Nm
- Hose Clamps2 lb-ft3 Nm
Fuel Filter6 specs
- Air Box Clips4 lb-ft5 Nm
- Filter Bracket Bolt12 lb-ft16 Nm
- Fuel Filter Bracket Bolt7 lb-ft10 Nm
- Fuel Line FittingsIf threaded type18 lb-ft25 Nm
- Oil Drain PlugUse new crush washer18 lb-ft25 Nm
- Wheel Lug NutsTorque in star pattern118 lb-ft160 Nm
Fuel Filter - In-Tank3 specs
- Filter Bracket Bolt12 lb-ft16 Nm
- Fuel Line FittingsUse new O-rings18 lb-ft25 Nm
- Hose Clamps2 lb-ft3 Nm
Fuel Injector - Single3 specs
- Fuel Line FittingsUse new O-rings18 lb-ft25 Nm
- Fuel Rail Bolts9 lb-ft12 Nm
- Hose Clamps2 lb-ft3 Nm
Fuel Injector Cleaning3 specs
- Fuel Line FittingsUse new O-rings18 lb-ft25 Nm
- Fuel Rail Bolts9 lb-ft12 Nm
- Hose Clamps2 lb-ft3 Nm
Fuel Injectors - All3 specs
- Fuel Line FittingsUse new O-rings18 lb-ft25 Nm
- Fuel Rail Bolts7.4 lb-ft10 Nm
- Hose Clamps2 lb-ft3 Nm
Fuel Level Sensor2 specs
- Fuel Line FittingsUse new O-rings18 lb-ft25 Nm
- Hose Clamps2 lb-ft3 Nm
Fuel Line - High Pressure3 specs
- Fuel Line FittingsUse new O-rings18 lb-ft25 Nm
- Fuel Rail Bolts9 lb-ft12 Nm
- Hose Clamps2 lb-ft3 Nm
Fuel Line - Return3 specs
- Fuel Line FittingsUse new O-rings15 lb-ft21 Nm
- Fuel Rail Bolts9 lb-ft12 Nm
- Hose Clamps2 lb-ft3 Nm
Fuel Pressure Regulator3 specs
- Fuel Line18 lb-ft25 Nm
- Fuel Rail Bolts7 lb-ft10 Nm
- Regulator Mounting Screws4 lb-ft5 Nm
Fuel Pump2 specs
- Fuel Pump Module Lock RingUse special tool33 lb-ft45 Nm
- Tank Strap Bolts6.6 lb-ft9 Nm
Fuel Pump Module4 specs
- Access Cover Screws3 lb-ft5 Nm
- Fuel Line FittingsUse new O-rings18 lb-ft25 Nm
- Fuel Pump Lock RingLock ring tool33 lb-ft45 Nm
- Hose Clamps2 lb-ft3 Nm
Fuel Rail3 specs
- Fuel Line FittingsUse new O-rings18 lb-ft25 Nm
- Fuel Rail Bolts7.4 lb-ft10 Nm
- Hose Clamps2 lb-ft3 Nm
Fuel Tank4 specs
- Filler Neck Clamp5.9 lb-ft8 Nm
- Fuel Line FittingsUse new O-rings18 lb-ft25 Nm
- Fuel Rail Bolts7 lb-ft10 Nm
- Tank Strap Bolts6.6 lb-ft9 Nm
Fuel Tank Strap2 specs
- Fuel Line FittingsUse new O-rings18 lb-ft25 Nm
- Hose Clamps2 lb-ft3 Nm
High Pressure Fuel Pump3 specs
- Fuel Line FittingsUse new O-rings18 lb-ft25 Nm
- Fuel Rail Bolts7.4 lb-ft10 Nm
- Hose Clamps2 lb-ft3 Nm
Electrical
Airbag - Driver2 specs
- Airbag Module BoltsTorx - disconnect battery and wait 2 minutes5 lb-ft7 Nm
- Steering Wheel Nut40 lb-ft54 Nm
Airbag - Passenger2 specs
- Airbag Module BoltsTorx - disconnect battery and wait 2 minutes5 lb-ft7 Nm
- Dashboard Fasteners3 lb-ft4 Nm
Airbag - Side2 specs
- Seat Mounting BoltsSafety critical45 lb-ft61 Nm
- Side Airbag Module BoltsTorx5 lb-ft7 Nm
Airbag Module/Computer3 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Module Mounting Bolts4.4 lb-ft6 Nm
- Sensor Mounting Bolts7 lb-ft10 Nm
Alternator4 specs
- Alternator Mounting Bolts18 lb-ft25 Nm
- Alternator Pivot Bolt18 lb-ft25 Nm
- Battery Terminal BoltsDo not overtighten6 lb-ft8 Nm
- Serpentine Belt Tensioner41 lb-ft55 Nm
Alternator Belt3 specs
- Alternator Mounting Bolts18 lb-ft25 Nm
- Alternator Pivot Bolt40 lb-ft55 Nm
- Battery Cable Nut12 lb-ft16 Nm
Amplifier3 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Ground Strap BoltsEnsure clean contact9 lb-ft12 Nm
- Module Mounting Bolts5.9 lb-ft8 Nm
Antenna1 spec
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
Backup Camera3 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Module Mounting Bolts6 lb-ft8 Nm
- Sensor Mounting Bolts7 lb-ft10 Nm
Battery3 specs
- Battery Hold-Down Bolt4.4 lb-ft6 Nm
- Battery Terminal BoltsDo not overtighten - can crack terminal4.4 lb-ft6 Nm
- Battery Tray Bolts9 lb-ft12 Nm
Battery Cable - Negative5 specs
- Battery Hold-Down BoltDo not overtighten4.4 lb-ft6 Nm
- Battery Terminal BoltsDo not overtighten4.4 lb-ft6 Nm
- Ground Cable Bolt7 lb-ft9 Nm
- Ground Strap BoltsEnsure clean contact9 lb-ft12 Nm
- Sensor Mounting Bolts7 lb-ft10 Nm
Battery Cable - Positive4 specs
- Battery Hold-Down BoltDo not overtighten4.4 lb-ft6 Nm
- Battery Terminal BoltsDo not overtighten4.4 lb-ft6 Nm
- Ground Cable Bolt7 lb-ft9 Nm
- Module Mounting Bolts6 lb-ft8 Nm
Battery Cables - Both5 specs
- Battery Hold-Down BoltDo not overtighten4.4 lb-ft6 Nm
- Battery Terminal BoltsDo not overtighten4.4 lb-ft6 Nm
- Ground Cable Bolt7 lb-ft9 Nm
- Ground Strap BoltsEnsure clean contact9 lb-ft12 Nm
- Sensor Mounting Bolts7 lb-ft10 Nm
Battery Terminal5 specs
- Battery Hold-Down BoltDo not overtighten4.4 lb-ft6 Nm
- Battery Terminal BoltsDo not overtighten4.4 lb-ft6 Nm
- Ground Cable Bolt7 lb-ft9 Nm
- Ground Strap BoltsEnsure clean contact9 lb-ft12 Nm
- Sensor Mounting Bolts7 lb-ft10 Nm
Blower Motor2 specs
- Blower Motor Mounting Screw3 lb-ft4 Nm
- Blower Motor Resistor Screws1.5 lb-ft2 Nm
Blower Motor Control Module2 specs
- Battery Terminal BoltsDo not overtighten4.4 lb-ft6 Nm
- Module Mounting Bolts6 lb-ft8 Nm
Blower Motor Resistor1 spec
- Resistor Screws1.5 lb-ft2 Nm
Clock Spring4 specs
- Airbag Module BoltsTorx - disconnect battery first5 lb-ft7 Nm
- Clock Spring ScrewsAlign marks before removal3 lb-ft4 Nm
- Steering Column CoversPlastic clips2 lb-ft3 Nm
- Steering Wheel Nut40 lb-ft54 Nm
Combination Switch3 specs
- Battery Terminal BoltsDo not overtighten4.4 lb-ft6 Nm
- Module Mounting Bolts6 lb-ft8 Nm
- Sensor Mounting Bolts7 lb-ft10 Nm
Dimmer Switch2 specs
- Battery Terminal BoltsDo not overtighten4.4 lb-ft6 Nm
- Module Mounting Bolts6 lb-ft8 Nm
Door Lock Actuator - Front1 spec
- Battery Terminal BoltsDo not overtighten4.4 lb-ft6 Nm
Door Lock Actuator - Rear1 spec
- Battery Terminal BoltsDo not overtighten4.4 lb-ft6 Nm
Fog Light Assembly1 spec
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
Fuel Pump Relay3 specs
- Access Cover Screws3 lb-ft5 Nm
- Fuel Pump Lock RingLock ring tool33 lb-ft45 Nm
- Relay Socket4 lb-ft5 Nm
Fuse Box - Engine Bay3 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Ground Strap BoltsEnsure clean contact9 lb-ft12 Nm
- Module Mounting Bolts6 lb-ft8 Nm
Fuse Box - Interior3 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Ground Strap BoltsEnsure clean contact9 lb-ft12 Nm
- Module Mounting Bolts6 lb-ft8 Nm
Headlight Assembly2 specs
- Adjuster Screws2 lb-ft3 Nm
- Headlight Assembly Bolts7 lb-ft10 Nm
Headlight Bulb - Single1 spec
- Bulb Retaining Ring4 lb-ft5 Nm
Headlight Switch2 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Module Mounting Bolts6 lb-ft8 Nm
Heated Seat Module2 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Module Mounting Bolts6 lb-ft8 Nm
HID Ballast2 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Module Mounting Bolts6 lb-ft8 Nm
Horn1 spec
- Horn Mounting Bolt11 lb-ft15 Nm
Horn Relay1 spec
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
Instrument Cluster2 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Module Mounting Bolts6 lb-ft8 Nm
LED Headlight Module2 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Module Mounting Bolts3.7 lb-ft5 Nm
Main Relay2 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Module Mounting Bolts6 lb-ft8 Nm
Power Antenna Motor1 spec
- Battery Terminal BoltsDo not overtighten9.4 lb-ft12.8 Nm
Power Mirror Motor1 spec
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
Power Seat Motor2 specs
- Battery Terminal BoltsDo not overtighten9.4 lb-ft12.8 Nm
- Module Mounting Bolts6 lb-ft8 Nm
Power Window Motor - Front2 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Module Mounting Bolts6 lb-ft8 Nm
Power Window Motor - Rear2 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Module Mounting Bolts6 lb-ft8 Nm
Power Window Regulator - Front2 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Module Mounting Bolts6 lb-ft8 Nm
Power Window Regulator - Rear1 spec
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
Radio/Head Unit2 specs
- Battery Terminal BoltsDo not overtighten9.4 lb-ft12.8 Nm
- Module Mounting Bolts6 lb-ft8 Nm
Relay - Generic2 specs
- Battery Terminal BoltsDo not overtighten9.4 lb-ft12.8 Nm
- Module Mounting Bolts6 lb-ft8 Nm
Seat Heater Element3 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Module Mounting Bolts6 lb-ft8 Nm
- Sensor Mounting Bolts7 lb-ft10 Nm
Side Mirror Assembly1 spec
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
Speaker - Dash2 specs
- Battery Terminal BoltsDo not overtighten4.4 lb-ft6 Nm
- Sensor Mounting Bolts7 lb-ft10 Nm
Speaker - Door1 spec
- Battery Terminal BoltsDo not overtighten4.4 lb-ft6 Nm
Speedometer3 specs
- Battery Terminal BoltsDo not overtighten4.4 lb-ft6 Nm
- Module Mounting Bolts6 lb-ft8 Nm
- Sensor Mounting Bolts7 lb-ft10 Nm
Starter3 specs
- Heat Shield BoltsIf equipped7 lb-ft10 Nm
- Starter Mounting BoltLong bolt may need extension22.1 lb-ft30 Nm
- Starter Solenoid NutFor B+ cable5.2 lb-ft7 Nm
Starter Solenoid3 specs
- Battery Cable Nut12 lb-ft16 Nm
- Battery Terminal BoltsDo not overtighten4.4 lb-ft6 Nm
- Starter Mounting Bolt40 lb-ft55 Nm
Subwoofer2 specs
- Battery Terminal BoltsDo not overtighten4.4 lb-ft6 Nm
- Module Mounting Bolts6 lb-ft8 Nm
Tail Light Assembly2 specs
- Lens Screws1.5 lb-ft2 Nm
- Tail Light Bolts2.2 lb-ft3 Nm
Tail Light Bulb1 spec
- Battery Terminal BoltsDo not overtighten4.4 lb-ft6 Nm
Third Brake Light1 spec
- Battery Terminal BoltsDo not overtighten. Verify sequence with the service manual4.4 lb-ft6 Nm
Trunk/Liftgate Actuator1 spec
- Battery Terminal BoltsDo not overtighten4.4 lb-ft6 Nm
Turn Signal Bulb - Front1 spec
- Battery Terminal BoltsDo not overtighten4.4 lb-ft6 Nm
Turn Signal Bulb - Rear1 spec
- Battery Terminal BoltsDo not overtighten4.4 lb-ft6 Nm
Turn Signal Switch2 specs
- Steering Column Covers1.5 lb-ft2 Nm
- Switch Mounting Screws2 lb-ft3 Nm
Voltage Regulator2 specs
- Battery Terminal BoltsDo not overtighten4.4 lb-ft6 Nm
- Module Mounting Bolts6 lb-ft8 Nm
Washer Pump1 spec
- Battery Terminal BoltsDo not overtighten4.4 lb-ft6 Nm
Washer Reservoir2 specs
- Battery Terminal BoltsDo not overtighten4.4 lb-ft6 Nm
- Sensor Mounting Bolts7 lb-ft10 Nm
Window Motor and Regulator - Front2 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Module Mounting Bolts6 lb-ft8 Nm
Window Motor and Regulator - Rear2 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Module Mounting Bolts6 lb-ft8 Nm
Wiper Linkage6 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Ground Strap BoltsEnsure clean contact9 lb-ft12 Nm
- Linkage Pivot Nuts17.7 lb-ft24 Nm
- Module Mounting Bolts6 lb-ft8 Nm
- Motor Mounting Bolts7 lb-ft10 Nm
- Sensor Mounting Bolts7 lb-ft10 Nm
Wiper Motor - Front2 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Module Mounting Bolts6 lb-ft8 Nm
Wiper Motor - Rear1 spec
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
Wiper Switch1 spec
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
Suspension
Air Line2 specs
- Strut Bolts98 lb-ft133 Nm
- Wheel Lug Nuts105 lb-ft142.4 Nm
Air Spring/Air Bag5 specs
- Control Arm BoltsTorque with vehicle weight on wheels122 lb-ft165 Nm
- Strut Bolts98 lb-ft133 Nm
- Strut Tower Nuts37 lb-ft50 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug Nuts105 lb-ft142.4 Nm
Air Suspension Compressor2 specs
- Strut Bolts98 lb-ft133 Nm
- Wheel Lug Nuts105 lb-ft142.4 Nm
Air Suspension Height Sensor2 specs
- Strut Bolts98 lb-ft133 Nm
- Wheel Lug Nuts105 lb-ft142.4 Nm
Air Suspension Valve Block2 specs
- Strut Bolts98 lb-ft133 Nm
- Wheel Lug Nuts105 lb-ft142.4 Nm
Ball Joint - Lower6 specs
- Control Arm BoltsTorque with vehicle weight on wheels122 lb-ft165 Nm
- Lower Ball Joint Nut75 lb-ft101 Nm
- Pinch BoltNew bolt52 lb-ft70 Nm
- Strut Tower Nuts37 lb-ft50 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug Nuts105 lb-ft142.4 Nm
Ball Joint - Upper6 specs
- Control Arm BoltsTorque with vehicle weight on wheels122 lb-ft165 Nm
- Pinch BoltNew bolt52 lb-ft70 Nm
- Strut Tower Nuts37 lb-ft50 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Upper Ball Joint Nut75 lb-ft101 Nm
- Wheel Lug Nuts105 lb-ft142.4 Nm
Ball Joints - Upper and Lower7 specs
- Control Arm BoltsTorque with vehicle weight on wheels122 lb-ft165 Nm
- Lower Ball Joint Nut75 lb-ft101 Nm
- Pinch BoltNew bolt52 lb-ft70 Nm
- Strut Tower Nuts37 lb-ft50 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Upper Ball Joint NutNew cotter pin74.5 lb-ft101 Nm
- Wheel Lug Nuts105 lb-ft142.4 Nm
Coil Spring - Front5 specs
- Control Arm BoltsTorque with vehicle weight on wheels122 lb-ft165 Nm
- Strut Bolts98 lb-ft133 Nm
- Strut Tower Nuts37 lb-ft50 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug Nuts105 lb-ft142.4 Nm
Coil Spring - Rear5 specs
- Control Arm BoltsTorque with vehicle weight on wheels122 lb-ft165 Nm
- Strut Bolts98 lb-ft133 Nm
- Strut Tower Nuts37 lb-ft50 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug Nuts105 lb-ft142.4 Nm
Coil Springs - Front Pair5 specs
- Control Arm BoltsTorque with vehicle weight on wheels122 lb-ft165 Nm
- Strut Bolts98 lb-ft133 Nm
- Strut Tower Nuts37 lb-ft50 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug Nuts105 lb-ft142.4 Nm
Coil Springs - Rear Pair5 specs
- Control Arm BoltsTorque with vehicle weight on wheels122 lb-ft165 Nm
- Strut Bolts98 lb-ft133 Nm
- Strut Tower Nuts37 lb-ft50 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug Nuts105 lb-ft142.4 Nm
Control Arm Bushing - Front Lower5 specs
- Control Arm BoltsTorque with vehicle weight on wheels122 lb-ft165 Nm
- Lower Ball Joint Nut75 lb-ft101 Nm
- Strut Tower Nuts37 lb-ft50 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug Nuts105 lb-ft142.4 Nm
Control Arm Bushing - Front Upper5 specs
- Control Arm BoltsTorque with vehicle weight on wheels122 lb-ft165 Nm
- Strut Tower Nuts37 lb-ft50 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Upper Ball Joint Nut75 lb-ft101 Nm
- Wheel Lug Nuts105 lb-ft142.4 Nm
Control Arm Bushing - Rear5 specs
- Ball Joint Nut75 lb-ft101 Nm
- Control Arm BoltsTorque with vehicle weight on wheels122 lb-ft165 Nm
- Strut Tower Nuts37 lb-ft50 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug Nuts105 lb-ft142.4 Nm
Front Struts - Pair7 specs
- Control Arm BoltsTorque with vehicle weight on wheels122 lb-ft165 Nm
- Strut Bolts98 lb-ft133 Nm
- Strut to Knuckle Bolts104 lb-ft140 Nm
- Strut Tower Nuts37 lb-ft50 Nm
- Sway Bar Link52 lb-ft70 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug Nuts105 lb-ft142.4 Nm
Front Suspension Rebuild5 specs
- Ball Joint Pinch BoltUse new bolt if locknut style37 lb-ft50 Nm
- Lower Control Arm BoltsTorque at ride height81 lb-ft110 Nm
- Strut Top Mount Nuts18 lb-ft25 Nm
- Sway Bar End Link Nuts44 lb-ft60 Nm
- Upper Control Arm BoltsTorque at ride height66 lb-ft90 Nm
Knuckle/Spindle - Front7 specs
- Control Arm BoltsTorque with vehicle weight on wheels122 lb-ft165 Nm
- Lower Ball Joint Nut75 lb-ft101 Nm
- Strut Bolts98 lb-ft133 Nm
- Strut Tower Nuts37 lb-ft50 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Upper Ball Joint Nut74.5 lb-ft101 Nm
- Wheel Lug Nuts105 lb-ft142.4 Nm
Knuckle/Spindle - Rear6 specs
- Ball Joint Nut75 lb-ft101 Nm
- Control Arm BoltsTorque with vehicle weight on wheels122 lb-ft165 Nm
- Strut Bolts98 lb-ft133 Nm
- Strut Tower Nuts37 lb-ft50 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug Nuts105 lb-ft142.4 Nm
Lateral Arm4 specs
- Control Arm BoltsTorque with vehicle weight on wheels122 lb-ft165 Nm
- Strut Bolts98 lb-ft133 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug Nuts105 lb-ft142.4 Nm
Lower Control Arm - Front6 specs
- Control Arm BoltsTorque with vehicle weight on wheels122 lb-ft165 Nm
- Lower Ball Joint Nut75 lb-ft101 Nm
- Strut Bolts98 lb-ft133 Nm
- Strut Tower Nuts37 lb-ft50 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug Nuts105 lb-ft142.4 Nm
Lower Control Arm - Rear6 specs
- Control Arm BoltsTorque with vehicle weight on wheels122 lb-ft165 Nm
- Lower Ball Joint Nut75 lb-ft101 Nm
- Strut Bolts98 lb-ft133 Nm
- Strut Tower Nuts37 lb-ft50 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug Nuts105 lb-ft142.4 Nm
Radius Arm5 specs
- Control Arm BoltsTorque with vehicle weight on wheels122 lb-ft165 Nm
- Strut Bolts98 lb-ft133 Nm
- Strut Tower Nuts37 lb-ft50 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug Nuts115 lb-ft156 Nm
Radius Arm Bushing5 specs
- Control Arm BoltsTorque with vehicle weight on wheels122 lb-ft165 Nm
- Strut Bolts98 lb-ft133 Nm
- Strut Tower Nuts37 lb-ft50 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug Nuts115 lb-ft156 Nm
Rear Shocks - Pair4 specs
- Strut Bolts98 lb-ft133 Nm
- Strut Tower Nuts37 lb-ft50 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug Nuts105 lb-ft142.4 Nm
Rear Suspension Service4 specs
- Lower Control Arm BoltsTorque at ride height66 lb-ft90 Nm
- Shock Lower Bolt52 lb-ft70 Nm
- Sway Bar End Link Nuts37 lb-ft50 Nm
- Trailing Arm BoltsTorque at ride height88 lb-ft120 Nm
Shock Absorber Replacement2 specs
- Lower Mount Bolt66 lb-ft90 Nm
- Upper Mount NutUse new self-locking nut41 lb-ft55 Nm
Strut Assembly - Rear6 specs
- Control Arm BoltsTorque with vehicle weight on wheels122 lb-ft165 Nm
- Strut to Knuckle Bolts104 lb-ft140 Nm
- Strut Tower Nuts37 lb-ft50 Nm
- Sway Bar Link52 lb-ft70 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug Nuts105 lb-ft142.4 Nm
Strut Bearing5 specs
- Strut to Knuckle Bolts104 lb-ft140 Nm
- Strut Tower Nuts37 lb-ft50 Nm
- Sway Bar Link52 lb-ft70 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug Nuts115 lb-ft156 Nm
Strut Mount - Front6 specs
- Control Arm BoltsTorque with vehicle weight on wheels122 lb-ft165 Nm
- Strut to Knuckle Bolts104 lb-ft140 Nm
- Strut Tower Nuts37 lb-ft50 Nm
- Sway Bar Link52 lb-ft70 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug Nuts105 lb-ft142.4 Nm
Strut Mount - Rear6 specs
- Control Arm BoltsTorque with vehicle weight on wheels122 lb-ft165 Nm
- Strut to Knuckle Bolts104 lb-ft140 Nm
- Strut Tower Nuts37 lb-ft50 Nm
- Sway Bar Link52 lb-ft70 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug Nuts105 lb-ft142.4 Nm
Subframe5 specs
- Control Arm BoltsTorque with vehicle weight on wheels122 lb-ft165 Nm
- Strut Bolts98 lb-ft133 Nm
- Strut Tower Nuts37 lb-ft50 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug Nuts105 lb-ft142.4 Nm
Subframe Bushing5 specs
- Control Arm BoltsTorque with vehicle weight on wheels122 lb-ft165 Nm
- Strut Bolts98 lb-ft133 Nm
- Strut Tower Nuts37 lb-ft50 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug Nuts115 lb-ft156 Nm
Sway Bar - Front3 specs
- Strut Bolts98 lb-ft133 Nm
- Sway Bar Bracket Bolts40 lb-ft55 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
Sway Bar - Rear3 specs
- Strut Bolts98 lb-ft133 Nm
- Sway Bar Bracket Bolts40 lb-ft55 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
Sway Bar Bushing - Front3 specs
- Strut Bolts98 lb-ft133 Nm
- Sway Bar Bracket Bolts40 lb-ft55 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
Sway Bar Bushing - Rear3 specs
- Strut Bolts98 lb-ft133 Nm
- Sway Bar Bracket Bolts40 lb-ft55 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
Sway Bar Link - Front3 specs
- Strut Bolts98 lb-ft133 Nm
- Sway Bar Bracket Bolts40 lb-ft55 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
Sway Bar Link - Rear3 specs
- Strut Bolts98 lb-ft133 Nm
- Sway Bar Bracket Bolts40 lb-ft55 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
Sway Bar Links - Front Pair3 specs
- Strut Bolts98 lb-ft133 Nm
- Sway Bar Bracket Bolts40 lb-ft55 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
Torsion Bar4 specs
- Control Arm BoltsTorque with vehicle weight on wheels122 lb-ft165 Nm
- Strut Bolts98 lb-ft133 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug Nuts115 lb-ft156 Nm
Torsion Bar Adjustment2 specs
- Strut Bolts98 lb-ft133 Nm
- Wheel Lug Nuts115 lb-ft156 Nm
Trailing Arm4 specs
- Control Arm BoltsTorque with vehicle weight on wheels122 lb-ft165 Nm
- Strut Bolts98 lb-ft133 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug Nuts115 lb-ft156 Nm
Trailing Arm Bushing4 specs
- Control Arm BoltsTorque with vehicle weight on wheels122 lb-ft165 Nm
- Strut Bolts98 lb-ft133 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug Nuts115 lb-ft156 Nm
Upper Control Arm - Front6 specs
- Control Arm BoltsTorque with vehicle weight on wheels122 lb-ft165 Nm
- Strut Bolts98 lb-ft133 Nm
- Strut Tower Nuts37 lb-ft50 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Upper Ball Joint Nut75 lb-ft101 Nm
- Wheel Lug Nuts105 lb-ft142.4 Nm
Upper Control Arm - Rear6 specs
- Control Arm BoltsTorque with vehicle weight on wheels122 lb-ft165 Nm
- Strut Bolts98 lb-ft133 Nm
- Strut Tower Nuts37 lb-ft50 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Upper Ball Joint Nut75 lb-ft101 Nm
- Wheel Lug Nuts105 lb-ft142.4 Nm
Steering
Electric Power Steering Module4 specs
- Power Steering Line FittingsUse new O-rings22 lb-ft30 Nm
- Steering Rack Bolts74 lb-ft100 Nm
- Tie Rod Nut46 lb-ft62 Nm
- Wheel Lug Nuts105 lb-ft142.4 Nm
Electric Power Steering Motor5 specs
- Power Steering Line FittingsUse new O-rings22 lb-ft30 Nm
- Steering Rack Bolts74 lb-ft100 Nm
- Tie Rod End Castle NutUse new cotter pin41 lb-ft55 Nm
- Tie Rod Nut46 lb-ft62 Nm
- Wheel Lug Nuts105 lb-ft142.4 Nm
Power Steering Hose - High Pressure5 specs
- Power Steering Line FittingsUse new O-rings22 lb-ft30 Nm
- Steering Rack Bolts74 lb-ft100 Nm
- Tie Rod End Castle NutUse new cotter pin41 lb-ft55 Nm
- Tie Rod Nut46 lb-ft62 Nm
- Wheel Lug Nuts105 lb-ft142.4 Nm
Power Steering Hose - Return5 specs
- Power Steering Line FittingsUse new O-rings22 lb-ft30 Nm
- Steering Rack Bolts74 lb-ft100 Nm
- Tie Rod End Castle NutUse new cotter pin41 lb-ft55 Nm
- Tie Rod Nut46 lb-ft62 Nm
- Wheel Lug Nuts105 lb-ft142.4 Nm
Power Steering Rack7 specs
- Power Steering Line FittingsUse new O-rings. Verify sequence with the service manual22 lb-ft30 Nm
- Pressure Line FittingNew O-ring29 lb-ft39 Nm
- Pump Mounting Bolts6.6 lb-ft9 Nm
- Steering Rack BoltsVerify sequence with the service manual74 lb-ft100 Nm
- Tie Rod End Castle NutUse new cotter pin. Verify sequence with the service manual41 lb-ft55 Nm
- Tie Rod Nut46 lb-ft62 Nm
- Wheel Lug Nuts105 lb-ft142.4 Nm
Power Steering Reservoir5 specs
- Power Steering Line FittingsUse new O-rings22 lb-ft30 Nm
- Steering Rack Bolts86 lb-ft117 Nm
- Tie Rod End Castle NutUse new cotter pin41 lb-ft55 Nm
- Tie Rod Nut46 lb-ft62 Nm
- Wheel Lug Nuts105 lb-ft142.4 Nm
Rack and Pinion Boots5 specs
- Power Steering Line FittingsUse new O-rings22 lb-ft30 Nm
- Steering Rack Bolts86 lb-ft117 Nm
- Tie Rod End Castle NutUse new cotter pin41 lb-ft55 Nm
- Tie Rod Nut46 lb-ft62 Nm
- Wheel Lug Nuts105 lb-ft142.4 Nm
Steering Angle Sensor3 specs
- Steering Rack BoltsVerify sequence with the service manual74 lb-ft100 Nm
- Tie Rod Nut46 lb-ft62 Nm
- Wheel Lug Nuts105 lb-ft142.4 Nm
Steering Column6 specs
- Ignition Switch BoltsVerify sequence with the service manual4 lb-ft5 Nm
- Pinch BoltVerify sequence with the service manual22 lb-ft30 Nm
- Steering Column BoltsVerify sequence with the service manual22 lb-ft30 Nm
- Steering Rack Bolts86 lb-ft117 Nm
- Tie Rod Nut46 lb-ft62 Nm
- Wheel Lug Nuts105 lb-ft142.4 Nm
Steering Coupler3 specs
- Steering Rack BoltsVerify sequence with the service manual74 lb-ft100 Nm
- Tie Rod Nut46 lb-ft62 Nm
- Wheel Lug Nuts105 lb-ft142.4 Nm
Steering Damper3 specs
- Steering Rack BoltsVerify sequence with the service manual74 lb-ft100 Nm
- Tie Rod Nut46 lb-ft62 Nm
- Wheel Lug Nuts115 lb-ft156 Nm
Steering Shaft - Intermediate4 specs
- Power Steering Line FittingsUse new O-rings. Verify sequence with the service manual22 lb-ft30 Nm
- Steering Rack BoltsVerify sequence with the service manual74 lb-ft100 Nm
- Tie Rod Nut46 lb-ft62 Nm
- Wheel Lug Nuts105 lb-ft142.4 Nm
Steering Shaft - Upper4 specs
- Power Steering Line FittingsUse new O-rings. Verify sequence with the service manual22 lb-ft30 Nm
- Steering Rack BoltsVerify sequence with the service manual74 lb-ft100 Nm
- Tie Rod Nut46 lb-ft62 Nm
- Wheel Lug Nuts105 lb-ft142.4 Nm
Steering Wheel5 specs
- Airbag Module BoltsTorx - usually T30. Verify sequence with the service manual5 lb-ft7 Nm
- Steering Rack Bolts86 lb-ft117 Nm
- Steering Wheel NutVerify sequence with the service manual40 lb-ft54 Nm
- Tie Rod Nut46 lb-ft62 Nm
- Wheel Lug Nuts105 lb-ft142.4 Nm
Tie Rod Assembly7 specs
- Power Steering Line FittingsUse new O-rings22 lb-ft30 Nm
- Steering Rack Bolts86 lb-ft117 Nm
- Tie Rod End Castle NutUse new cotter pin41 lb-ft55 Nm
- Tie Rod End NutNew cotter pin46 lb-ft62 Nm
- Tie Rod Lock NutAfter alignment58 lb-ft78 Nm
- Tie Rod Nut46 lb-ft62 Nm
- Wheel Lug Nuts105 lb-ft142.4 Nm
Tie Rod End - Inner7 specs
- Power Steering Line FittingsUse new O-rings22 lb-ft30 Nm
- Steering Rack Bolts74 lb-ft100 Nm
- Tie Rod End Castle NutUse new cotter pin41 lb-ft55 Nm
- Tie Rod End NutNew cotter pin46 lb-ft62 Nm
- Tie Rod Lock NutAfter alignment58 lb-ft78 Nm
- Tie Rod Nut46 lb-ft62 Nm
- Wheel Lug Nuts105 lb-ft142.4 Nm
Tie Rod End - Outer7 specs
- Power Steering Line FittingsUse new O-rings22 lb-ft30 Nm
- Steering Rack Bolts86 lb-ft117 Nm
- Tie Rod End Castle NutUse new cotter pin41 lb-ft55 Nm
- Tie Rod End NutNew cotter pin46 lb-ft62 Nm
- Tie Rod Lock NutAfter alignment58 lb-ft78 Nm
- Tie Rod Nut46 lb-ft62 Nm
- Wheel Lug Nuts105 lb-ft142.4 Nm
Tie Rods - Both Sides7 specs
- Power Steering Line FittingsUse new O-rings22 lb-ft30 Nm
- Steering Rack Bolts86 lb-ft117 Nm
- Tie Rod End Castle NutUse new cotter pin41 lb-ft55 Nm
- Tie Rod End NutNew cotter pin46 lb-ft62 Nm
- Tie Rod Lock NutAfter alignment58 lb-ft78 Nm
- Tie Rod Nut46 lb-ft62 Nm
- Wheel Lug Nuts105 lb-ft142.4 Nm
Drivetrain
Axle Seal - Rear4 specs
- Axle NutUse new cotter pin or stake nut184 lb-ft250 Nm
- CV Bolts52 lb-ft70 Nm
- Differential Cover Bolts26 lb-ft35 Nm
- Wheel Lug NutsTorque in star pattern118 lb-ft160 Nm
CV Axle - Rear5 specs
- Axle Nut207 lb-ft281 Nm
- Ball Joint Nut86 lb-ft117 Nm
- CV Axle Nut148 lb-ft200 Nm
- CV Bolts52 lb-ft70 Nm
- Wheel Lug Nuts105 lb-ft142.4 Nm
CV Boot - Inner4 specs
- Axle NutUse new cotter pin or stake nut184 lb-ft250 Nm
- CV Bolts52 lb-ft70 Nm
- Differential Cover Bolts26 lb-ft35 Nm
- Wheel Lug NutsTorque in star pattern118 lb-ft160 Nm
CV Boot - Outer4 specs
- Axle NutUse new cotter pin or stake nut184 lb-ft250 Nm
- CV Bolts52 lb-ft70 Nm
- Differential Cover Bolts26 lb-ft35 Nm
- Wheel Lug NutsTorque in star pattern118 lb-ft160 Nm
Differential Cover Gasket2 specs
- CV Bolts52 lb-ft70 Nm
- Differential Cover Bolts26 lb-ft35 Nm
Differential Fluid Change - Rear2 specs
- CV Bolts52 lb-ft70 Nm
- Differential Cover Bolts26 lb-ft35 Nm
Differential Pinion Seal3 specs
- CV Bolts52 lb-ft70 Nm
- Differential Cover Bolts26 lb-ft35 Nm
- Driveshaft U-Joint StrapsTighten evenly15 lb-ft20 Nm
Differential Rebuild - Rear7 specs
- Axle NutUse new cotter pin or stake nut184 lb-ft250 Nm
- CV Bolts52 lb-ft70 Nm
- Differential Cover Bolts26 lb-ft35 Nm
- Drain PlugNew washer35 lb-ft47 Nm
- Driveshaft U-Joint StrapsTighten evenly15 lb-ft20 Nm
- Fill Plug35 lb-ft47 Nm
- Wheel Lug NutsTorque in star pattern118 lb-ft160 Nm
Driveshaft - Rear3 specs
- Differential Pinion Yoke NutUse new nut, set pinion preload184 lb-ft250 Nm
- Driveshaft Flange Bolts55 lb-ft75 Nm
- U-Joint Strap BoltsApply threadlocker26 lb-ft35 Nm
Driveshaft Center Support Bearing2 specs
- Center Support Bearing Bracket Bolts37 lb-ft50 Nm
- Driveshaft Flange Bolts55 lb-ft75 Nm
Limited Slip Clutch Pack5 specs
- Axle NutUse new cotter pin or stake nut184 lb-ft250 Nm
- CV Bolts52 lb-ft70 Nm
- Differential Cover Bolts26 lb-ft35 Nm
- Driveshaft U-Joint StrapsTighten evenly15 lb-ft20 Nm
- Wheel Lug NutsTorque in star pattern118 lb-ft160 Nm
Ring and Pinion5 specs
- Axle NutUse new cotter pin or stake nut184 lb-ft250 Nm
- CV Bolts52 lb-ft70 Nm
- Differential Cover Bolts26 lb-ft35 Nm
- Driveshaft U-Joint StrapsTighten evenly15 lb-ft20 Nm
- Wheel Lug NutsTorque in star pattern118 lb-ft160 Nm
U-Joint5 specs
- Axle Nut207 lb-ft281 Nm
- CV Bolts52 lb-ft70 Nm
- Driveshaft U-Joint StrapsTighten evenly15 lb-ft20 Nm
- Wheel Lug Nuts115 lb-ft156 Nm
- Yoke NutIf equipped111 lb-ft150 Nm
Wheel Bearing - Press-In Front4 specs
- ABS Sensor Bolt5.9 lb-ft8 Nm
- Axle NutUse new cotter pin or stake nut184 lb-ft250 Nm
- Hub Bolts86 lb-ft117 Nm
- Wheel Lug NutsTorque in star pattern118 lb-ft160 Nm
Wheel Bearing - Press-In Rear5 specs
- ABS Sensor Bolt5.9 lb-ft8 Nm
- Axle NutUse new cotter pin or stake nut184 lb-ft250 Nm
- Differential Cover Bolts26 lb-ft35 Nm
- Hub Bolts86 lb-ft117 Nm
- Wheel Lug NutsTorque in star pattern118 lb-ft160 Nm
Wheel Bearing Hub - Front4 specs
- ABS Sensor BoltDo not overtighten5.9 lb-ft8 Nm
- Axle NutUse new cotter pin after torque184 lb-ft250 Nm
- Caliper Bracket Bolts88 lb-ft120 Nm
- Wheel Bearing Hub BoltsApply threadlocker if specified81 lb-ft110 Nm
Wheel Bearing Hub - Rear3 specs
- Axle NutUse new cotter pin after torque148 lb-ft200 Nm
- Caliper Bracket Bolts81 lb-ft110 Nm
- Wheel Bearing Hub BoltsApply threadlocker if specified74 lb-ft100 Nm
Wheel Studs3 specs
- Axle NutUse new cotter pin or stake nut184 lb-ft250 Nm
- CV Bolts52 lb-ft70 Nm
- Wheel Lug NutsTorque in star pattern118 lb-ft160 Nm
Transmission
Neutral Safety Switch1 spec
- Switch Mounting Bolts11 lb-ft15 Nm
Overdrive Solenoid2 specs
- Transmission Drain PlugUse new crush washer if equipped36.9 lb-ft50 Nm
- Transmission Pan BoltsTighten in criss-cross pattern9 lb-ft12 Nm
Pressure Plate2 specs
- Flywheel BoltsOften TTY, tighten in star pattern70 lb-ft95 Nm
- Transmission Drain PlugUse new crush washer if equipped36.9 lb-ft50 Nm
Shift Cable2 specs
- Adjustment Nut7 lb-ft10 Nm
- Cable Bracket Bolts11 lb-ft15 Nm
Shift Fork1 spec
- Transmission Drain PlugUse new crush washer if equipped36.9 lb-ft50 Nm
Shift Linkage2 specs
- Linkage Bolts11 lb-ft15 Nm
- Pivot Bolts9 lb-ft12 Nm
Shift Solenoid - Single3 specs
- Flywheel BoltsOften TTY, tighten in star pattern66.4 lb-ft90 Nm
- Transmission Drain PlugUse new crush washer if equipped36.9 lb-ft50 Nm
- Transmission Pan BoltsTighten in criss-cross pattern9 lb-ft12 Nm
Shift Solenoids - All2 specs
- Transmission Drain PlugUse new crush washer if equipped36.9 lb-ft50 Nm
- Transmission Pan BoltsTighten in criss-cross pattern9 lb-ft12 Nm
Synchros - All2 specs
- Transmission Drain PlugUse new crush washer if equipped36.9 lb-ft50 Nm
- Transmission Pan BoltsTighten in criss-cross pattern9 lb-ft12 Nm
Synchros - Single Gear1 spec
- Transmission Drain PlugUse new crush washer if equipped36.9 lb-ft50 Nm
Torque Converter2 specs
- Flexplate BoltsAutomatic transmissions63 lb-ft85 Nm
- Torque Converter BoltsTighten evenly37 lb-ft50 Nm
Torque Converter Clutch Solenoid2 specs
- Transmission Drain PlugUse new crush washer if equipped36.9 lb-ft50 Nm
- Transmission Pan BoltsTighten in criss-cross pattern9 lb-ft12 Nm
Transmission Control Module2 specs
- Transmission Drain PlugUse new crush washer if equipped22 lb-ft30 Nm
- Transmission Pan BoltsTighten in criss-cross pattern9 lb-ft12 Nm
Transmission Cooler Lines1 spec
- Transmission Drain PlugUse new crush washer if equipped36.9 lb-ft50 Nm
Transmission Filter2 specs
- Transmission Drain PlugUse new crush washer if equipped36.9 lb-ft50 Nm
- Transmission Pan BoltsTighten in criss-cross pattern9 lb-ft12 Nm
Transmission Filter and Fluid2 specs
- Transmission Drain PlugUse new crush washer if equipped36.9 lb-ft50 Nm
- Transmission Pan BoltsTighten in criss-cross pattern9 lb-ft12 Nm
Transmission Fluid Change3 specs
- Transmission Drain PlugUse new crush washer if equipped36.9 lb-ft50 Nm
- Transmission Filter BoltsIf equipped with bolted filter7.4 lb-ft10 Nm
- Transmission Pan BoltsTighten in criss-cross pattern9 lb-ft12 Nm
Transmission Flush2 specs
- Transmission Drain PlugUse new crush washer if equipped36.9 lb-ft50 Nm
- Transmission Pan BoltsTighten in criss-cross pattern9 lb-ft12 Nm
Transmission Input Shaft Bearing3 specs
- Flywheel BoltsOften TTY, tighten in star pattern70 lb-ft95 Nm
- Transmission Drain PlugUse new crush washer if equipped36.9 lb-ft50 Nm
- Transmission Pan BoltsTighten in criss-cross pattern9 lb-ft12 Nm
Transmission Oil Cooler6 specs
- Coolant Drain Plug11 lb-ft15 Nm
- Hose Clamps2 lb-ft3 Nm
- Pump Bolts21 lb-ft28 Nm
- Thermostat Housing Bolt7.4 lb-ft10 Nm
- Transmission Drain PlugUse new crush washer if equipped36.9 lb-ft50 Nm
- Water Pump BoltsTighten in criss-cross pattern7.4 lb-ft10 Nm
Transmission Output Shaft Bearing3 specs
- Flywheel BoltsOften TTY, tighten in star pattern70 lb-ft95 Nm
- Transmission Drain PlugUse new crush washer if equipped36.9 lb-ft50 Nm
- Transmission Pan BoltsTighten in criss-cross pattern9 lb-ft12 Nm
Transmission Pan Gasket2 specs
- Transmission Drain PlugUse new crush washer if equipped36.9 lb-ft50 Nm
- Transmission Pan BoltsTighten in criss-cross pattern9 lb-ft12 Nm
Transmission R&R - Automatic3 specs
- Flywheel BoltsOften TTY, tighten in star pattern70 lb-ft95 Nm
- Transmission Drain PlugUse new crush washer if equipped36.9 lb-ft50 Nm
- Transmission Pan BoltsTighten in criss-cross pattern9 lb-ft12 Nm
Transmission Range Sensor2 specs
- Transmission Drain PlugUse new crush washer if equipped36.9 lb-ft50 Nm
- Transmission Pan BoltsTighten in criss-cross pattern9 lb-ft12 Nm
Transmission Rebuild - Automatic3 specs
- Flywheel BoltsOften TTY, tighten in star pattern70 lb-ft95 Nm
- Transmission Drain PlugUse new crush washer if equipped36.9 lb-ft50 Nm
- Transmission Pan BoltsTighten in criss-cross pattern9 lb-ft12 Nm
Transmission Speed Sensor - Input2 specs
- Transmission Drain PlugUse new crush washer if equipped36.9 lb-ft50 Nm
- Transmission Pan BoltsTighten in criss-cross pattern9 lb-ft12 Nm
Transmission Speed Sensor - Output1 spec
- Transmission Drain PlugUse new crush washer if equipped36.9 lb-ft50 Nm
Valve Body2 specs
- Transmission Drain PlugUse new crush washer if equipped36.9 lb-ft50 Nm
- Transmission Pan BoltsTighten in criss-cross pattern9 lb-ft12 Nm
Exhaust
Catalytic Converter - Direct Fit4 specs
- Exhaust Flange BoltApply anti-seize33 lb-ft45 Nm
- Hanger Bolts5.9 lb-ft8 Nm
- Heat Shield Bolts7 lb-ft10 Nm
- O2 SensorApply anti-seize to threads only33 lb-ft45 Nm
Catalytic Converter - Universal4 specs
- Exhaust Flange BoltApply anti-seize33 lb-ft45 Nm
- Hanger Bolts5.9 lb-ft8 Nm
- Heat Shield Bolts7 lb-ft10 Nm
- O2 SensorApply anti-seize to threads only33 lb-ft45 Nm
Downpipe4 specs
- Exhaust Flange BoltApply anti-seize33 lb-ft45 Nm
- Hanger Bolts17 lb-ft23 Nm
- Heat Shield Bolts7.4 lb-ft10 Nm
- O2 SensorApply anti-seize to threads only33 lb-ft45 Nm
EGR Tube3 specs
- Exhaust Flange BoltApply anti-seize33 lb-ft45 Nm
- Hanger Bolts17 lb-ft23 Nm
- Heat Shield Bolts7 lb-ft10 Nm
EGR Valve4 specs
- EGR Tube Fitting26 lb-ft35 Nm
- EGR Valve Bolts18 lb-ft25 Nm
- Hanger Bolts17 lb-ft23 Nm
- O2 Sensor40 lb-ft55 Nm
Exhaust Clamp4 specs
- Exhaust Flange BoltApply anti-seize18 lb-ft25 Nm
- Hanger Bolts17 lb-ft23 Nm
- Heat Shield Bolts7 lb-ft10 Nm
- O2 SensorApply anti-seize to threads only33 lb-ft45 Nm
Exhaust Gasket - Front4 specs
- Exhaust Flange BoltApply anti-seize18 lb-ft25 Nm
- Hanger Bolts17 lb-ft23 Nm
- Heat Shield Bolts7 lb-ft10 Nm
- O2 SensorApply anti-seize to threads only33 lb-ft45 Nm
Exhaust Gasket - Rear4 specs
- Exhaust Flange BoltApply anti-seize18 lb-ft25 Nm
- Hanger Bolts17 lb-ft23 Nm
- Heat Shield Bolts7 lb-ft10 Nm
- O2 SensorApply anti-seize to threads only33 lb-ft45 Nm
Exhaust Hangers4 specs
- Exhaust Flange BoltApply anti-seize18 lb-ft25 Nm
- Hanger Bolts17 lb-ft23 Nm
- Heat Shield Bolts7 lb-ft10 Nm
- O2 SensorApply anti-seize to threads only33 lb-ft45 Nm
Exhaust Manifold Studs4 specs
- Exhaust Flange BoltApply anti-seize18 lb-ft25 Nm
- Hanger Bolts17 lb-ft23 Nm
- Heat Shield Bolts7.4 lb-ft10 Nm
- O2 SensorApply anti-seize to threads only33 lb-ft45 Nm
Exhaust Pipe - Rear Section4 specs
- Exhaust Flange BoltApply anti-seize18 lb-ft25 Nm
- Hanger Bolts17 lb-ft23 Nm
- Heat Shield Bolts7 lb-ft10 Nm
- O2 SensorApply anti-seize to threads only33 lb-ft45 Nm
Exhaust Tip2 specs
- Exhaust Flange BoltApply anti-seize33 lb-ft45 Nm
- Hanger Bolts17 lb-ft23 Nm
Flex Pipe3 specs
- Exhaust Clamps41 lb-ft55 Nm
- Hanger Bolts17 lb-ft23 Nm
- O2 Sensor33 lb-ft45 Nm
Front Pipe4 specs
- Exhaust Flange BoltApply anti-seize33 lb-ft45 Nm
- Hanger Bolts17 lb-ft23 Nm
- Heat Shield Bolts7 lb-ft10 Nm
- O2 SensorApply anti-seize to threads only33 lb-ft45 Nm
Intermediate Pipe4 specs
- Exhaust Flange BoltApply anti-seize33 lb-ft45 Nm
- Hanger Bolts17 lb-ft23 Nm
- Heat Shield Bolts7 lb-ft10 Nm
- O2 SensorApply anti-seize to threads only33 lb-ft45 Nm
Muffler2 specs
- Hanger Bracket Bolts5.9 lb-ft8 Nm
- Muffler Clamps10.3 lb-ft14 Nm
O2 Sensor - Downstream4 specs
- Exhaust Flange BoltApply anti-seize18 lb-ft25 Nm
- Hanger Bolts17 lb-ft23 Nm
- Heat Shield Bolts7.4 lb-ft10 Nm
- O2 SensorApply anti-seize to threads only33 lb-ft45 Nm
O2 Sensor - Upstream4 specs
- Exhaust Flange BoltApply anti-seize18 lb-ft25 Nm
- Hanger Bolts17 lb-ft23 Nm
- Heat Shield Bolts7.4 lb-ft10 Nm
- O2 SensorApply anti-seize to threads only33 lb-ft45 Nm
O2 Sensors - All4 specs
- Exhaust Flange BoltApply anti-seize18 lb-ft25 Nm
- Hanger Bolts17 lb-ft23 Nm
- Heat Shield Bolts7.4 lb-ft10 Nm
- O2 SensorApply anti-seize to threads only33 lb-ft45 Nm
Resonator3 specs
- Exhaust Clamps10.3 lb-ft14 Nm
- Hanger Bolts17 lb-ft23 Nm
- O2 Sensor40 lb-ft55 Nm
Tail Pipe3 specs
- Exhaust Flange BoltApply anti-seize33 lb-ft45 Nm
- Hanger Bolts17 lb-ft23 Nm
- Heat Shield Bolts7 lb-ft10 Nm
Heating and A/C
AC Accumulator3 specs
- AC Line FittingsUse new O-rings, add PAG oil15 lb-ft20 Nm
- Blower Motor Mounting Screw3 lb-ft4 Nm
- Compressor Bolts29 lb-ft39 Nm
AC Clutch Coil2 specs
- Blower Motor Mounting Screw3 lb-ft4 Nm
- Compressor Bolts29 lb-ft39 Nm
AC Compressor3 specs
- AC Compressor Bolts18.4 lb-ft25 Nm
- AC Line FittingsUse new O-rings, add PAG oil7.4 lb-ft10 Nm
- Clutch Connector Bolt6 lb-ft8 Nm
AC Compressor Clutch2 specs
- Blower Motor Mounting Screw3 lb-ft4 Nm
- Compressor Bolts29 lb-ft39 Nm
AC Compressor Oil Add3 specs
- AC Line FittingsUse new O-rings, add PAG oil15 lb-ft20 Nm
- Blower Motor Mounting Screw3 lb-ft4 Nm
- Compressor Bolts18 lb-ft25 Nm
AC Condenser2 specs
- AC Line FittingsUse new O-rings5.9 lb-ft8 Nm
- Condenser Mounting Bolts3 lb-ft4 Nm
AC Evaporator4 specs
- AC Line FittingsUse new O-rings, add PAG oil15 lb-ft20 Nm
- Compressor Bolts18 lb-ft25 Nm
- Evaporator Case Screws4 lb-ft5 Nm
- Expansion Valve7 lb-ft10 Nm
AC Expansion Valve (TXV)3 specs
- AC Line FittingsUse new O-rings, add PAG oil15 lb-ft20 Nm
- Compressor Bolts18 lb-ft25 Nm
- Expansion Valve7 lb-ft10 Nm
AC High Pressure Switch3 specs
- AC Line FittingsUse new O-rings, add PAG oil15 lb-ft20 Nm
- Blower Motor Mounting Screw3 lb-ft4 Nm
- Compressor Bolts18 lb-ft25 Nm
AC Hose - High Side3 specs
- AC Line FittingsUse new O-rings, add PAG oil15 lb-ft20 Nm
- Blower Motor Mounting Screw3 lb-ft4 Nm
- Compressor Bolts18 lb-ft25 Nm
AC Hose - Low Side4 specs
- AC Line FittingsUse new O-rings, add PAG oil15 lb-ft20 Nm
- Blower Motor Mounting Screw3 lb-ft4 Nm
- Compressor Bolts18 lb-ft25 Nm
- Hose Clamps2 lb-ft3 Nm
AC Hose Assembly4 specs
- AC Line FittingsUse new O-rings, add PAG oil15 lb-ft20 Nm
- Blower Motor Mounting Screw3 lb-ft4 Nm
- Compressor Bolts18 lb-ft25 Nm
- Hose Clamps2 lb-ft3 Nm
AC Low Pressure Switch3 specs
- AC Line FittingsUse new O-rings, add PAG oil15 lb-ft20 Nm
- Blower Motor Mounting Screw3 lb-ft4 Nm
- Compressor Bolts18 lb-ft25 Nm
AC Orifice Tube3 specs
- AC Line FittingsUse new O-rings, add PAG oil15 lb-ft20 Nm
- Blower Motor Mounting Screw3 lb-ft4 Nm
- Compressor Bolts29 lb-ft39 Nm
AC Pressure Sensor3 specs
- AC Line FittingsUse new O-rings, add PAG oil15 lb-ft20 Nm
- Blower Motor Mounting Screw3 lb-ft4 Nm
- Compressor Bolts18 lb-ft25 Nm
AC Receiver/Drier3 specs
- AC Line FittingsUse new O-rings, add PAG oil15 lb-ft20 Nm
- Compressor Bolts18 lb-ft25 Nm
- Receiver Drier Bolts5.9 lb-ft8 Nm
AC Recharge2 specs
- Blower Motor Mounting Screw3 lb-ft4 Nm
- Compressor Bolts18 lb-ft25 Nm
Blend Door Actuator2 specs
- Actuator Screws2 lb-ft3 Nm
- Compressor Bolts18 lb-ft25 Nm
Cabin Air Filter2 specs
- Compressor Bolts29 lb-ft39 Nm
- Filter Cover Clips4 lb-ft5 Nm
Climate Control Module2 specs
- Blower Motor Mounting Screw3 lb-ft4 Nm
- Compressor Bolts18 lb-ft25 Nm
HVAC Control Panel2 specs
- Blower Motor Mounting Screw3 lb-ft4 Nm
- Compressor Bolts18 lb-ft25 Nm
Mode Door Actuator2 specs
- Blower Motor Mounting Screw3 lb-ft4 Nm
- Compressor Bolts18 lb-ft25 Nm
Recirculation Door Actuator2 specs
- Blower Motor Mounting Screw3 lb-ft4 Nm
- Compressor Bolts18 lb-ft25 Nm
Body
Bumper Cover - Front3 specs
- Bumper Cover Bolts3.3 lb-ft4.5 Nm
- Fender Liner Screws2.2 lb-ft3 Nm
- Grille Clips4 lb-ft5 Nm
Bumper Cover - Rear2 specs
- Bumper Cover Bolts4.4 lb-ft6 Nm
- Trunk Liner Screws2 lb-ft3 Nm
Bumper Reinforcement - Front3 specs
- Body Panel Bolts18 lb-ft25 Nm
- Bumper Cover Bolts7 lb-ft10 Nm
- Door Hinge Bolts32 lb-ft43 Nm
Bumper Reinforcement - Rear3 specs
- Body Panel Bolts18 lb-ft25 Nm
- Bumper Cover Bolts7 lb-ft10 Nm
- Door Hinge Bolts32 lb-ft43 Nm
Door Check/Stop2 specs
- Body Panel Bolts18 lb-ft25 Nm
- Door Hinge Bolts51.6 lb-ft70 Nm
Door Glass1 spec
- Door Hinge Bolts51.6 lb-ft70 Nm
Door Handle - Exterior2 specs
- Handle Mounting Bolts6 lb-ft8 Nm
- Lock Rod Clips4 lb-ft5 Nm
Door Handle - Interior2 specs
- Cable Clips4 lb-ft5 Nm
- Handle Screws2 lb-ft3 Nm
Door Hinge1 spec
- Door Hinge Bolts51.6 lb-ft70 Nm
Door Shell2 specs
- Body Panel Bolts18 lb-ft25 Nm
- Door Hinge Bolts51.6 lb-ft70 Nm
Door Skin2 specs
- Body Panel Bolts18 lb-ft25 Nm
- Door Hinge Bolts51.6 lb-ft70 Nm
Door Weatherstrip1 spec
- Door Hinge Bolts51.6 lb-ft70 Nm
Fender3 specs
- Fender Bolts3.7 lb-ft5 Nm
- Fender Liner Screws2.2 lb-ft3 Nm
- Hood Hinge Bolts18 lb-ft25 Nm
Fender Liner3 specs
- Body Panel Bolts18 lb-ft25 Nm
- Bumper Cover Bolts7 lb-ft10 Nm
- Door Hinge Bolts32 lb-ft43 Nm
Grille2 specs
- Clips4 lb-ft5 Nm
- Grille Mounting Screws2.2 lb-ft3 Nm
Hood3 specs
- Hood Hinge Bolts5.9 lb-ft8 Nm
- Hood Latch Bolts3.7 lb-ft5 Nm
- Hood Strut Bolts7 lb-ft10 Nm
Hood Hinge2 specs
- Body Panel Bolts18 lb-ft25 Nm
- Door Hinge Bolts18 lb-ft25 Nm
Hood Latch2 specs
- Cable Clips4 lb-ft5 Nm
- Hood Latch Bolts3.7 lb-ft5 Nm
Hood Release Cable2 specs
- Body Panel Bolts18 lb-ft25 Nm
- Bumper Cover Bolts7 lb-ft10 Nm
Hood Strut2 specs
- Body Panel Bolts18 lb-ft25 Nm
- Door Hinge Bolts18 lb-ft25 Nm
Quarter Glass1 spec
- Body Panel Bolts18 lb-ft25 Nm
Quarter Panel3 specs
- Body Panel Bolts18 lb-ft25 Nm
- Bumper Cover Bolts7 lb-ft10 Nm
- Door Hinge Bolts22 lb-ft30 Nm
Rear Window2 specs
- Body Panel Bolts18 lb-ft25 Nm
- Door Hinge Bolts32 lb-ft43 Nm
Rocker Panel3 specs
- Body Panel Bolts18 lb-ft25 Nm
- Bumper Cover Bolts7 lb-ft10 Nm
- Door Hinge Bolts32 lb-ft43 Nm
Trunk Hinge2 specs
- Body Panel Bolts18 lb-ft25 Nm
- Door Hinge Bolts18 lb-ft24 Nm
Trunk Latch1 spec
- Body Panel Bolts18 lb-ft25 Nm
Trunk Lid2 specs
- Trunk Hinge Bolts18 lb-ft25 Nm
- Trunk Latch Bolts9 lb-ft12 Nm
Trunk Strut1 spec
- Body Panel Bolts18 lb-ft25 Nm
Windshield1 spec
- Body Panel Bolts18 lb-ft25 Nm
Interior
Armrest1 spec
- Trim Panel ClipsReplace if damaged1.5 lb-ft2 Nm
Carpet3 specs
- Dashboard Screws2 lb-ft3 Nm
- Seat Mounting BoltsSafety critical33 lb-ft45 Nm
- Trim Panel ClipsReplace if damaged1.5 lb-ft2 Nm
Center Console2 specs
- Console Screws2.2 lb-ft3 Nm
- Shifter Trim4 lb-ft5 Nm
Dash Pad3 specs
- Dashboard Screws2 lb-ft3 Nm
- Seat Mounting BoltsSafety critical33 lb-ft45 Nm
- Trim Panel ClipsReplace if damaged1.5 lb-ft2 Nm
Dashboard3 specs
- Dashboard Bolt9 lb-ft12 Nm
- Dashboard Screws2 lb-ft3 Nm
- Trim Panel ClipsReplace if damaged1.5 lb-ft2 Nm
Door Panel2 specs
- Door Panel Screws4.4 lb-ft6 Nm
- Trim Panel ClipsReplace if damaged1.5 lb-ft2 Nm
Floor Mat Hooks2 specs
- Seat Mounting BoltsSafety critical33 lb-ft45 Nm
- Trim Panel ClipsReplace if damaged1.5 lb-ft2 Nm
Glove Box2 specs
- Glove Box Screws2 lb-ft3 Nm
- Hinge Screws1.5 lb-ft2 Nm
Glove Box Latch3 specs
- Dashboard Screws2 lb-ft3 Nm
- Seat Mounting BoltsSafety critical33 lb-ft45 Nm
- Trim Panel ClipsReplace if damaged1.5 lb-ft2 Nm
Headliner2 specs
- Seat Mounting BoltsSafety critical33 lb-ft45 Nm
- Trim Panel ClipsReplace if damaged1.5 lb-ft2 Nm
Pedal Pads1 spec
- Trim Panel ClipsReplace if damaged1.5 lb-ft2 Nm
Rearview Mirror1 spec
- Trim Panel ClipsReplace if damaged1.5 lb-ft2 Nm
Seat - Front3 specs
- Electrical Connectors4 lb-ft5 Nm
- Seat Mounting BoltsSafety critical33 lb-ft45 Nm
- Seat Track Bolts14.8 lb-ft20 Nm
Seat - Rear2 specs
- Seat Back Release11 lb-ft15 Nm
- Seat Mounting Bolts26 lb-ft35 Nm
Seat Belt2 specs
- Seat Mounting BoltsSafety critical33 lb-ft45 Nm
- Trim Panel ClipsReplace if damaged1.5 lb-ft2 Nm
Seat Belt Buckle2 specs
- Seat Mounting BoltsSafety critical33 lb-ft45 Nm
- Trim Panel ClipsReplace if damaged1.5 lb-ft2 Nm
Seat Belt Pretensioner2 specs
- Seat Mounting BoltsSafety critical33 lb-ft45 Nm
- Trim Panel ClipsReplace if damaged1.5 lb-ft2 Nm
Seat Cover2 specs
- Seat Mounting BoltsSafety critical33 lb-ft45 Nm
- Trim Panel ClipsReplace if damaged1.5 lb-ft2 Nm
Seat Foam2 specs
- Seat Mounting BoltsSafety critical33 lb-ft45 Nm
- Trim Panel ClipsReplace if damaged1.5 lb-ft2 Nm
Seat Track2 specs
- Seat Mounting BoltsSafety critical33 lb-ft45 Nm
- Trim Panel ClipsReplace if damaged1.5 lb-ft2 Nm
Shifter Boot1 spec
- Trim Panel ClipsReplace if damaged1.5 lb-ft2 Nm
Shifter Knob1 spec
- Trim Panel ClipsReplace if damaged1.5 lb-ft2 Nm
Steering Wheel Cover2 specs
- Dashboard ScrewsVerify sequence with the service manual2 lb-ft3 Nm
- Trim Panel ClipsReplace if damaged. Verify sequence with the service manual1.5 lb-ft2 Nm
Sun Visor1 spec
- Visor Mounting Screws4.4 lb-ft6 Nm
Torque is shown in lb-ft with Nm below it. Where a step says to turn, tighten the listed angle after the torque step before it. Use new bolts where the note says so.
Need labor times, fluids or repair steps for this car? See it on the Open Labor Project