2020 McLaren 570S torque specs

3.8L V8 Twin Turbo

Change vehicle

Most looked up

Lug nuts112 lb-ft152 Nm
Oil drain plug18 lb-ft25 Nm
Spark plugs17 lb-ft23 Nm
Front caliper bracket bolts88 lb-ft120 Nm
Rear caliper bracket bolts74 lb-ft100 Nm
Front axle nut207 lb-ft281 Nm
Outer tie rod end nut46 lb-ft62 Nm

Maintenance

AC System Diagnosis3 specs
- AC Line FittingsNew O-rings17 lb-ft23 Nm
- Connector Bolts6 lb-ft8 Nm
- Oil Drain PlugUse new crush washer18 lb-ft25 Nm
Air Filter4 specs
- Air Box Clips4 lb-ft5 Nm
- Intake Tube Clamp3 lb-ft4 Nm
- MAF Sensor Screws3 lb-ft5 Nm
- Mass Air Flow Sensor Screws2 lb-ft3 Nm
Battery Test6 specs
- Battery Hold-Down BoltDo not overtighten9 lb-ft12 Nm
- Battery Terminal BoltsClean terminals6 lb-ft8 Nm
- Connector Bolts6 lb-ft8 Nm
- Ground Cable Bolt7 lb-ft9 Nm
- Oil Drain PlugUse new crush washer18 lb-ft25 Nm
- Wheel Lug NutsTorque in star pattern112 lb-ft152 Nm
Charging System Test2 specs
- Connector Bolts6 lb-ft8 Nm
- Oil Drain PlugUse new crush washer18 lb-ft25 Nm
Check Engine Light Diagnosis2 specs
- Connector Bolts6 lb-ft8 Nm
- Oil Drain PlugUse new crush washer18 lb-ft25 Nm
Compression Test3 specs
- Air Box Clips4 lb-ft5 Nm
- Connector Bolts6 lb-ft8 Nm
- Oil Drain PlugUse new crush washer18 lb-ft25 Nm
Cooling System Pressure Test2 specs
- Connector Bolts6 lb-ft8 Nm
- Wheel Lug NutsTorque in star pattern112 lb-ft152 Nm
Diagnostic Scan3 specs
- Connector Bolts6 lb-ft8 Nm
- Oil Drain PlugUse new crush washer18 lb-ft25 Nm
- Wheel Lug NutsTorque in star pattern112 lb-ft152 Nm
Differential Service5 specs
- Connector Bolts6 lb-ft8 Nm
- Drain PlugNew washer35 lb-ft47 Nm
- Fill Plug35 lb-ft47 Nm
- Oil Drain PlugUse new crush washer18 lb-ft25 Nm
- Wheel Lug NutsTorque in star pattern112 lb-ft152 Nm
Drivability Diagnosis3 specs
- Air Box Clips4 lb-ft5 Nm
- Connector Bolts6 lb-ft8 Nm
- Oil Drain PlugUse new crush washer18 lb-ft25 Nm
Electrical Diagnosis3 specs
- Connector Bolts6 lb-ft8 Nm
- Oil Drain PlugUse new crush washer18 lb-ft25 Nm
- Wheel Lug NutsTorque in star pattern112 lb-ft152 Nm
Fluid Leak Diagnosis2 specs
- Connector Bolts6 lb-ft8 Nm
- Wheel Lug NutsTorque in star pattern112 lb-ft152 Nm
Leak-Down Test4 specs
- Air Box Clips4 lb-ft5 Nm
- Connector Bolts6 lb-ft8 Nm
- Oil Drain PlugUse new crush washer18 lb-ft25 Nm
- Wheel Lug NutsTorque in star pattern112 lb-ft152 Nm
Noise Diagnosis3 specs
- Connector Bolts6 lb-ft8 Nm
- Oil Drain PlugUse new crush washer18 lb-ft25 Nm
- Wheel Lug NutsTorque in star pattern112 lb-ft152 Nm
Power Steering Service6 specs
- Air Box ClipsVerify sequence with the service manual4 lb-ft5 Nm
- Connector Bolts6 lb-ft8 Nm
- Oil Drain PlugUse new crush washer. Verify sequence with the service manual18 lb-ft25 Nm
- Pressure Line FittingNew O-ring29 lb-ft39 Nm
- Pump Mounting Bolts18 lb-ft25 Nm
- Wheel Lug NutsTorque in star pattern. Verify sequence with the service manual112 lb-ft152 Nm
Tire Balance3 specs
- Connector Bolts6 lb-ft8 Nm
- Oil Drain PlugUse new crush washer18 lb-ft25 Nm
- Wheel Lug NutsTorque in star pattern112 lb-ft152 Nm
Tire Mount and Balance3 specs
- Connector Bolts6 lb-ft8 Nm
- Oil Drain PlugUse new crush washer18 lb-ft25 Nm
- Wheel Lug NutsTorque in star pattern112 lb-ft152 Nm
Tire Rotation2 specs
- Lug Nuts - Alloy WheelsTorque in star pattern, recheck after 50 miles118 lb-ft160 Nm
- Lug Nuts - Steel WheelsTorque in star pattern112 lb-ft152 Nm
TPMS Relearn3 specs
- Connector Bolts6 lb-ft8 Nm
- Oil Drain PlugUse new crush washer18 lb-ft25 Nm
- Wheel Lug NutsTorque in star pattern112 lb-ft152 Nm
TPMS Sensor3 specs
- Connector Bolts6 lb-ft8 Nm
- Oil Drain PlugUse new crush washer18 lb-ft25 Nm
- Wheel Lug NutsTorque in star pattern112 lb-ft152 Nm
Transmission Service2 specs
- Connector Bolts6 lb-ft8 Nm
- Wheel Lug NutsTorque in star pattern112 lb-ft152 Nm
Tune-Up - Major4 specs
- Air Box Clips4 lb-ft5 Nm
- Connector Bolts6 lb-ft8 Nm
- Oil Drain PlugUse new crush washer18 lb-ft25 Nm
- Wheel Lug NutsTorque in star pattern112 lb-ft152 Nm
Tune-Up - Minor4 specs
- Air Box Clips4 lb-ft5 Nm
- Connector Bolts6 lb-ft8 Nm
- Oil Drain PlugUse new crush washer18 lb-ft25 Nm
- Wheel Lug NutsTorque in star pattern112 lb-ft152 Nm
Wheel Alignment9 specs
- Air Box Clips4 lb-ft5 Nm
- Cam BoltsAfter adjustment105 lb-ft142 Nm
- Camber BoltsIf adjustable55 lb-ft75 Nm
- Connector Bolts6 lb-ft8 Nm
- Oil Drain PlugUse new crush washer18 lb-ft25 Nm
- Subframe BoltsIf adjusted83 lb-ft113 Nm
- Tie Rod Jam Nuts33 lb-ft45 Nm
- Tie Rod Lock NutAfter adjustment33 lb-ft45 Nm
- Wheel Lug NutsTorque in star pattern112 lb-ft152 Nm

Brakes

ABS Module5 specs
- ABS Module Bolts7 lb-ft10 Nm
- Bleeder Screw12 lb-ft16 Nm
- Brake Line FittingsUse flare nut wrench11 lb-ft15 Nm
- Caliper Mounting BoltsUse thread locker75 lb-ft102 Nm
- Wheel Lug NutsTorque in star pattern105 lb-ft142.4 Nm
ABS Pump4 specs
- Bleeder ScrewDo not overtighten7 lb-ft10 Nm
- Caliper Bracket Bolts - FrontThreadlocker recommended88 lb-ft120 Nm
- Caliper Mounting BoltsUse thread locker75 lb-ft102 Nm
- Wheel Lug NutsTorque in star pattern112 lb-ft152 Nm
ABS Tone Ring4 specs
- Caliper Bracket Bolts - FrontThreadlocker recommended88 lb-ft120 Nm
- Caliper Mounting BoltsUse thread locker75 lb-ft102 Nm
- Caliper Slide Pin BoltsApply silicone brake grease26 lb-ft35 Nm
- Wheel Lug NutsTorque in star pattern112 lb-ft152 Nm
ABS Wheel Speed Sensor - Front5 specs
- ABS Sensor BoltDo not overtighten7 lb-ft10 Nm
- Bleeder Screw12 lb-ft16 Nm
- Caliper Mounting BoltsUse thread locker75 lb-ft102 Nm
- Wheel Bearing Hub Bolts81 lb-ft110 Nm
- Wheel Lug NutsTorque in star pattern105 lb-ft142.4 Nm
ABS Wheel Speed Sensor - Rear4 specs
- ABS Sensor BoltDo not overtighten7 lb-ft10 Nm
- Bleeder Screw12 lb-ft16 Nm
- Caliper Mounting BoltsUse thread locker75 lb-ft102 Nm
- Wheel Lug NutsTorque in star pattern105 lb-ft142.4 Nm
Brake Bleed - All Four4 specs
- Bleeder ScrewDo not overtighten. Verify sequence with the service manual7 lb-ft10 Nm
- Caliper Mounting BoltsUse thread locker75 lb-ft102 Nm
- Caliper Slide Pin BoltsApply silicone brake grease. Verify sequence with the service manual26 lb-ft35 Nm
- Wheel Lug NutsTorque in star pattern. Verify sequence with the service manual112 lb-ft152 Nm
Brake Booster6 specs
- Bleeder Screw12 lb-ft16 Nm
- Brake Booster NutsVerify sequence with the service manual18 lb-ft25 Nm
- Brake Pedal Pushrod LockVerify sequence with the service manual15 lb-ft20 Nm
- Caliper Mounting BoltsUse thread locker75 lb-ft102 Nm
- Master Cylinder NutsVerify sequence with the service manual18 lb-ft25 Nm
- Wheel Lug NutsTorque in star pattern115 lb-ft156 Nm
Brake Booster Check Valve4 specs
- Bleeder ScrewDo not overtighten. Verify sequence with the service manual7 lb-ft10 Nm
- Caliper Mounting BoltsUse thread locker75 lb-ft102 Nm
- Caliper Slide Pin BoltsApply silicone brake grease. Verify sequence with the service manual26 lb-ft35 Nm
- Wheel Lug NutsTorque in star pattern. Verify sequence with the service manual112 lb-ft152 Nm
Brake Caliper - Front3 specs
- Bleeder ScrewDo not overtighten7 lb-ft10 Nm
- Brake Line Banjo BoltUse new copper washers18 lb-ft25 Nm
- Caliper Bracket BoltsThreadlocker recommended88 lb-ft120 Nm
Brake Caliper - Rear3 specs
- Bleeder ScrewDo not overtighten7 lb-ft10 Nm
- Brake Line Banjo BoltUse new copper washers18 lb-ft25 Nm
- Caliper Bracket BoltsThreadlocker recommended74 lb-ft100 Nm
Brake Caliper Bracket6 specs
- Bleeder ScrewDo not overtighten. Verify sequence with the service manual7 lb-ft10 Nm
- Brake Hose Banjo BoltNew copper washers18 lb-ft25 Nm
- Caliper Bracket Bolts - FrontThreadlocker recommended. Verify sequence with the service manual88 lb-ft120 Nm
- Caliper Mounting BoltsUse thread locker75 lb-ft102 Nm
- Caliper Slide Pin BoltsApply silicone brake grease. Verify sequence with the service manual26 lb-ft35 Nm
- Wheel Lug NutsTorque in star pattern. Verify sequence with the service manual112 lb-ft152 Nm
Brake Caliper Rebuild - Front5 specs
- Bleeder ScrewDo not overtighten7 lb-ft10 Nm
- Caliper Bracket Bolts - FrontThreadlocker recommended88 lb-ft120 Nm
- Caliper Mounting BoltsUse thread locker75 lb-ft102 Nm
- Caliper Slide Pin BoltsApply silicone brake grease26 lb-ft35 Nm
- Wheel Lug NutsTorque in star pattern112 lb-ft152 Nm
Brake Caliper Rebuild - Rear5 specs
- Bleeder ScrewDo not overtighten7 lb-ft10 Nm
- Caliper Bracket Bolts - FrontThreadlocker recommended88 lb-ft120 Nm
- Caliper Mounting BoltsUse thread locker75 lb-ft102 Nm
- Caliper Slide Pin BoltsApply silicone brake grease26 lb-ft35 Nm
- Wheel Lug NutsTorque in star pattern112 lb-ft152 Nm
Brake Caliper Slide Pins4 specs
- Caliper Bracket Bolts - FrontThreadlocker recommended88 lb-ft120 Nm
- Caliper Mounting BoltsUse thread locker75 lb-ft102 Nm
- Caliper Slide Pin BoltsApply silicone brake grease26 lb-ft35 Nm
- Wheel Lug NutsTorque in star pattern112 lb-ft152 Nm
Brake Fluid Flush8 specs
- Air Box ClipsVerify sequence with the service manual4 lb-ft5 Nm
- Bleeder ScrewDo not overtighten. Verify sequence with the service manual7 lb-ft10 Nm
- Caliper Mounting Bolts75 lb-ft101 Nm
- Caliper Slide Pin BoltsApply silicone brake grease. Verify sequence with the service manual26 lb-ft35 Nm
- Connector Bolts6 lb-ft8 Nm
- Master Cylinder CapHand tight3 lb-ft4 Nm
- Oil Drain PlugUse new crush washer. Verify sequence with the service manual18 lb-ft25 Nm
- Wheel Lug NutsTorque in star pattern. Verify sequence with the service manual112 lb-ft152 Nm
Brake Hose - Front5 specs
- Bleeder Screw12 lb-ft16 Nm
- Brake Hose Banjo BoltUse new copper washers. Verify sequence with the service manual18 lb-ft25 Nm
- Brake Hose BracketVerify sequence with the service manual7 lb-ft10 Nm
- Caliper Mounting BoltsUse thread locker75 lb-ft102 Nm
- Wheel Lug NutsTorque in star pattern105 lb-ft142.4 Nm
Brake Hose - Rear5 specs
- Bleeder Screw12 lb-ft16 Nm
- Brake Hose Banjo BoltUse new copper washers. Verify sequence with the service manual18 lb-ft25 Nm
- Brake Hose BracketVerify sequence with the service manual7 lb-ft10 Nm
- Caliper Mounting BoltsUse thread locker75 lb-ft102 Nm
- Wheel Lug NutsTorque in star pattern105 lb-ft142.4 Nm
Brake Light Switch4 specs
- Bleeder ScrewDo not overtighten. Verify sequence with the service manual7 lb-ft10 Nm
- Caliper Bracket Bolts - FrontThreadlocker recommended. Verify sequence with the service manual88 lb-ft120 Nm
- Caliper Mounting BoltsUse thread locker75 lb-ft102 Nm
- Caliper Slide Pin BoltsApply silicone brake grease. Verify sequence with the service manual26 lb-ft35 Nm
Brake Line - Single5 specs
- Bleeder ScrewDo not overtighten. Verify sequence with the service manual7 lb-ft10 Nm
- Caliper Bracket Bolts - FrontThreadlocker recommended. Verify sequence with the service manual88 lb-ft120 Nm
- Caliper Mounting BoltsUse thread locker75 lb-ft102 Nm
- Caliper Slide Pin BoltsApply silicone brake grease. Verify sequence with the service manual26 lb-ft35 Nm
- Wheel Lug NutsTorque in star pattern. Verify sequence with the service manual112 lb-ft152 Nm
Brake Lines - Complete Set5 specs
- Bleeder ScrewDo not overtighten. Verify sequence with the service manual7 lb-ft10 Nm
- Caliper Bracket Bolts - FrontThreadlocker recommended. Verify sequence with the service manual88 lb-ft120 Nm
- Caliper Mounting BoltsUse thread locker75 lb-ft102 Nm
- Caliper Slide Pin BoltsApply silicone brake grease. Verify sequence with the service manual26 lb-ft35 Nm
- Wheel Lug NutsTorque in star pattern. Verify sequence with the service manual112 lb-ft152 Nm
Brake Master Cylinder2 specs
- Brake Line FittingsUse flare nut wrench11 lb-ft15 Nm
- Master Cylinder Nuts18 lb-ft25 Nm
Brake Master Cylinder Rebuild3 specs
- Brake Line FittingsUse flare nut wrench11 lb-ft15 Nm
- Master Cylinder Mounting Nuts18 lb-ft25 Nm
- Reservoir Mounting Bolts6 lb-ft8 Nm
Brake Pads - Front3 specs
- Caliper Bracket BoltsThreadlocker recommended88 lb-ft120 Nm
- Caliper Slide Pin BoltsApply silicone brake grease26 lb-ft35 Nm
- Wheel Lug NutsTorque in star pattern112 lb-ft152 Nm
Brake Pads - Rear3 specs
- Caliper Bracket BoltsThreadlocker recommended74 lb-ft100 Nm
- Caliper Slide Pin BoltsApply silicone brake grease22 lb-ft30 Nm
- Wheel Lug NutsTorque in star pattern112 lb-ft152 Nm
Brake Pads and Rotors - Front7 specs
- Bleeder ScrewDo not overtighten. Verify sequence with the service manual7 lb-ft10 Nm
- Caliper Bracket BoltsUse thread locker86 lb-ft117 Nm
- Caliper Bracket Bolts - FrontThreadlocker recommended. Verify sequence with the service manual88 lb-ft120 Nm
- Caliper Mounting BoltsUse thread locker75 lb-ft102 Nm
- Caliper Slide BoltsLubricate pins29 lb-ft39 Nm
- Caliper Slide Pin BoltsApply silicone brake grease. Verify sequence with the service manual26 lb-ft35 Nm
- Wheel Lug NutsTorque in star pattern. Verify sequence with the service manual112 lb-ft152 Nm
Brake Pads and Rotors - Rear7 specs
- Bleeder ScrewDo not overtighten. Verify sequence with the service manual7 lb-ft10 Nm
- Caliper Bracket BoltsUse thread locker86 lb-ft117 Nm
- Caliper Bracket Bolts - FrontThreadlocker recommended. Verify sequence with the service manual88 lb-ft120 Nm
- Caliper Mounting BoltsUse thread locker75 lb-ft102 Nm
- Caliper Slide BoltsLubricate pins29 lb-ft39 Nm
- Caliper Slide Pin BoltsApply silicone brake grease. Verify sequence with the service manual26 lb-ft35 Nm
- Wheel Lug NutsTorque in star pattern. Verify sequence with the service manual112 lb-ft152 Nm
Brake Proportioning Valve5 specs
- Bleeder Screw12 lb-ft16 Nm
- Brake Line FittingsUse flare nut wrench. Verify sequence with the service manual11 lb-ft15 Nm
- Caliper Mounting BoltsUse thread locker75 lb-ft102 Nm
- Proportioning Valve BoltsVerify sequence with the service manual11 lb-ft15 Nm
- Wheel Lug NutsTorque in star pattern105 lb-ft142.4 Nm
Brake Rotor - Front Single8 specs
- Bleeder ScrewDo not overtighten. Verify sequence with the service manual7 lb-ft10 Nm
- Brake Rotor Set Screw6 lb-ft8 Nm
- Caliper Bracket Bolts86 lb-ft117 Nm
- Caliper Bracket Bolts - FrontThreadlocker recommended. Verify sequence with the service manual88 lb-ft120 Nm
- Caliper Mounting BoltsUse thread locker75 lb-ft102 Nm
- Caliper Slide Pin BoltsApply silicone brake grease. Verify sequence with the service manual26 lb-ft35 Nm
- Hub NutIf removed207 lb-ft281 Nm
- Wheel Lug NutsTorque in star pattern. Verify sequence with the service manual112 lb-ft152 Nm
Brake Rotor - Rear Single8 specs
- Bleeder ScrewDo not overtighten. Verify sequence with the service manual7 lb-ft10 Nm
- Brake Rotor Set Screw6 lb-ft8 Nm
- Caliper Bracket Bolts86 lb-ft117 Nm
- Caliper Bracket Bolts - FrontThreadlocker recommended. Verify sequence with the service manual88 lb-ft120 Nm
- Caliper Mounting BoltsUse thread locker75 lb-ft102 Nm
- Caliper Slide Pin BoltsApply silicone brake grease. Verify sequence with the service manual26 lb-ft35 Nm
- Hub NutIf removed207 lb-ft281 Nm
- Wheel Lug NutsTorque in star pattern. Verify sequence with the service manual112 lb-ft152 Nm
Brake Rotors - Front Pair8 specs
- Bleeder ScrewDo not overtighten. Verify sequence with the service manual7 lb-ft10 Nm
- Brake Rotor Set Screw6 lb-ft8 Nm
- Caliper Bracket Bolts86 lb-ft117 Nm
- Caliper Bracket Bolts - FrontThreadlocker recommended. Verify sequence with the service manual88 lb-ft120 Nm
- Caliper Mounting BoltsUse thread locker75 lb-ft102 Nm
- Caliper Slide Pin BoltsApply silicone brake grease. Verify sequence with the service manual26 lb-ft35 Nm
- Hub NutIf removed207 lb-ft281 Nm
- Wheel Lug NutsTorque in star pattern. Verify sequence with the service manual112 lb-ft152 Nm
Brake Rotors - Rear Pair8 specs
- Bleeder ScrewDo not overtighten. Verify sequence with the service manual7 lb-ft10 Nm
- Brake Rotor Set Screw6 lb-ft8 Nm
- Caliper Bracket Bolts86 lb-ft117 Nm
- Caliper Bracket Bolts - FrontThreadlocker recommended. Verify sequence with the service manual88 lb-ft120 Nm
- Caliper Mounting BoltsUse thread locker75 lb-ft102 Nm
- Caliper Slide Pin BoltsApply silicone brake grease. Verify sequence with the service manual26 lb-ft35 Nm
- Hub NutIf removed207 lb-ft281 Nm
- Wheel Lug NutsTorque in star pattern. Verify sequence with the service manual112 lb-ft152 Nm
Electronic Parking Brake Motor5 specs
- Bleeder ScrewDo not overtighten. Verify sequence with the service manual7 lb-ft10 Nm
- Caliper Bracket Bolts - FrontThreadlocker recommended. Verify sequence with the service manual88 lb-ft120 Nm
- Caliper Mounting BoltsUse thread locker75 lb-ft102 Nm
- Caliper Slide Pin BoltsApply silicone brake grease. Verify sequence with the service manual26 lb-ft35 Nm
- Wheel Lug NutsTorque in star pattern. Verify sequence with the service manual112 lb-ft152 Nm
Front Brake Pad Replacement3 specs
- Caliper Bracket BoltsThreadlocker recommended88 lb-ft120 Nm
- Caliper Slide Pin BoltsApply silicone brake grease26 lb-ft35 Nm
- Wheel Lug NutsTorque in star pattern112 lb-ft152 Nm
Parking Brake Actuator3 specs
- Caliper Mounting BoltsUse thread locker75 lb-ft102 Nm
- Caliper Slide Pin BoltsApply silicone brake grease. Verify sequence with the service manual26 lb-ft35 Nm
- Wheel Lug NutsTorque in star pattern. Verify sequence with the service manual112 lb-ft152 Nm
Parking Brake Cable5 specs
- Bleeder Screw12 lb-ft16 Nm
- Cable Bracket BoltsVerify sequence with the service manual9 lb-ft12 Nm
- Caliper Mounting BoltsUse thread locker75 lb-ft102 Nm
- Equalizer NutAdjust for proper tension. Verify sequence with the service manual11 lb-ft15 Nm
- Wheel Lug NutsTorque in star pattern105 lb-ft142.4 Nm
Parking Brake Shoes5 specs
- Adjuster LockVerify sequence with the service manual4 lb-ft5 Nm
- Bleeder Screw12 lb-ft16 Nm
- Caliper Mounting BoltsUse thread locker75 lb-ft102 Nm
- Hold-Down SpringsVerify sequence with the service manual6 lb-ft8 Nm
- Wheel Lug NutsTorque in star pattern. Verify sequence with the service manual112 lb-ft152 Nm

Engine

Boost Pressure Sensor4 specs
- Boost Sensor11 lb-ft15 Nm
- Electrical Connector Bolts6 lb-ft8 Nm
- Gasket Surface BoltsClean mating surfaces17 lb-ft23 Nm
- Sensor Mounting Bolts9 lb-ft12 Nm
Camshaft Position Sensor5 specs
- Camshaft Position Sensor7 lb-ft10 Nm
- Electrical Connector Bolts6 lb-ft8 Nm
- Gasket Surface BoltsClean mating surfaces17 lb-ft23 Nm
- Sensor Mounting Bolts9 lb-ft12 Nm
- Valve Cover BoltsTighten in sequence7 lb-ft10 Nm
Camshaft R&R20 specs
- Cam Phaser BoltApply threadlocker, hold cam stationary61 lb-ft83 Nm
- Camshaft Bearing Cap BoltsTighten in sequence, 3 passes10 lb-ft14 Nm
- Camshaft Cap BoltsTighten in sequence from center outward, multiple passes10 lb-ft14 Nm
- Camshaft Position Sensor7 lb-ft10 Nm
- Camshaft Sprocket BoltsHold cam with wrench on hex59 lb-ft80 Nm
- Crankshaft Position Sensor7 lb-ft10 Nm
- Crankshaft Pulley BoltOften TTY - check spec, may require impact133 lb-ft180 Nm
- Electrical Connector Bolts6 lb-ft8 Nm
- Gasket Surface BoltsClean mating surfaces17 lb-ft23 Nm
- Oil Drain PlugUse new crush washer18 lb-ft25 Nm
- Rocker Arm BoltsTighten with cam lobe pointing away22 lb-ft30 Nm
- Rocker Arm Shaft BoltsTighten evenly in sequence18 lb-ft25 Nm
- Sensor Mounting Bolts9 lb-ft12 Nm
- Timing Chain Guide BoltsReplace if worn9 lb-ft12 Nm
- Timing Chain Idler Sprocket18 lb-ft25 Nm
- Timing Chain Tensioner BoltInstall with pin/clip to compress18 lb-ft25 Nm
- Timing Cover Bolts - 10mmTighten in sequence33 lb-ft45 Nm
- Timing Cover Bolts - 8mmTighten in sequence18 lb-ft25 Nm
- Valve Cover BoltsTighten in sequence7 lb-ft10 Nm
- VVT Solenoid Bolt7 lb-ft10 Nm
Connecting Rod Bearings6 specs
- Connecting Rod BoltsTTY - critical torque plus angle33 lb-ft45 Nm
- Electrical Connector Bolts6 lb-ft8 Nm
- Gasket Surface BoltsClean mating surfaces17 lb-ft23 Nm
- Oil Drain PlugUse new crush washer18 lb-ft25 Nm
- Oil Pan BoltTighten in sequence9 lb-ft12 Nm
- Sensor Mounting Bolts9 lb-ft12 Nm
Crankshaft Position Sensor4 specs
- Crankshaft Position Sensor7 lb-ft10 Nm
- Electrical Connector Bolts6 lb-ft8 Nm
- Gasket Surface BoltsClean mating surfaces17 lb-ft23 Nm
- Sensor Mounting Bolts9 lb-ft12 Nm
Crankshaft R&R20 specs
- Connecting Rod BoltsTTY - critical torque plus angle33 lb-ft45 Nm
- Crankshaft Pulley BoltOften TTY - check spec, may require impact133 lb-ft180 Nm
- Cylinder Head BoltsTTY - tighten in sequence plus angle30 lb-ft40 Nm
- Electrical Connector Bolts6 lb-ft8 Nm
- Flexplate BoltsAutomatic transmissions63 lb-ft85 Nm
- Flywheel BoltsOften TTY, tighten in star pattern37 lb-ft50 Nm
- Front Main Seal Housing9 lb-ft12 Nm
- Gasket Surface BoltsClean mating surfaces17 lb-ft23 Nm
- Main Bearing Cap BoltsTTY - tighten in sequence plus angle22 lb-ft30 Nm
- Oil Drain PlugUse new crush washer26 lb-ft35 Nm
- Oil Pan BoltTighten in sequence9 lb-ft12 Nm
- Oil Pump Bolts18 lb-ft25 Nm
- Oil Pump Pickup Tube9 lb-ft12 Nm
- Rear Main Seal Housing9 lb-ft12 Nm
- Sensor Mounting Bolts9 lb-ft12 Nm
- Timing Chain Guide BoltsReplace if worn9 lb-ft12 Nm
- Timing Chain Tensioner BoltInstall with pin/clip to compress18 lb-ft25 Nm
- Timing Cover Bolts - 10mmTighten in sequence18 lb-ft25 Nm
- Timing Cover Bolts - 8mmTighten in sequence8 lb-ft11 Nm
- Transmission-to-Engine Bolts33 lb-ft45 Nm
Cylinder Head R&R17 specs
- Camshaft Bearing Cap BoltsTighten in sequence, 3 passes10 lb-ft14 Nm
- Camshaft Cap BoltsTighten in sequence from center outward, multiple passes10 lb-ft14 Nm
- Camshaft Sprocket BoltsHold cam with wrench on hex59 lb-ft80 Nm
- Cylinder Head BoltsTTY - tighten in sequence plus angle48 lb-ft65 Nm
- Electrical Connector Bolts6 lb-ft8 Nm
- Exhaust Manifold NutsApply anti-seize, work hot-to-cold18 lb-ft25 Nm
- Gasket Surface BoltsClean mating surfaces17 lb-ft23 Nm
- Intake Manifold Bolt9 lb-ft12 Nm
- Oil Drain PlugUse new crush washer18 lb-ft25 Nm
- Rocker Arm BoltsTighten with cam lobe pointing away22 lb-ft30 Nm
- Rocker Arm Shaft BoltsTighten evenly in sequence18 lb-ft25 Nm
- Sensor Mounting Bolts9 lb-ft12 Nm
- Thermostat Housing Bolt11 lb-ft15 Nm
- Timing Chain Guide BoltsReplace if worn9 lb-ft12 Nm
- Timing Chain Tensioner BoltInstall with pin/clip to compress18 lb-ft25 Nm
- Timing Cover Bolts - 8mmTighten in sequence18 lb-ft25 Nm
- Valve Cover BoltsTighten in sequence7 lb-ft10 Nm
Cylinder Head Resurface7 specs
- Cylinder Head BoltsTTY - tighten in sequence plus angle48 lb-ft65 Nm
- Electrical Connector Bolts6 lb-ft8 Nm
- Exhaust Manifold NutsApply anti-seize, work hot-to-cold18 lb-ft25 Nm
- Gasket Surface BoltsClean mating surfaces17 lb-ft23 Nm
- Intake Manifold Bolt9 lb-ft12 Nm
- Sensor Mounting Bolts9 lb-ft12 Nm
- Valve Cover BoltsTighten in sequence7 lb-ft10 Nm
Engine Mount - Front3 specs
- Engine Mount Through-Bolt63 lb-ft85 Nm
- Engine Mount-to-Block Bolts48 lb-ft65 Nm
- Engine Mount-to-Frame Bolts44 lb-ft60 Nm
Engine Mount - Rear6 specs
- Electrical Connector Bolts6 lb-ft8 Nm
- Engine Mount Through-Bolt63 lb-ft85 Nm
- Engine Mount-to-Block Bolts48 lb-ft65 Nm
- Engine Mount-to-Frame Bolts44 lb-ft60 Nm
- Gasket Surface BoltsClean mating surfaces17 lb-ft23 Nm
- Sensor Mounting Bolts9 lb-ft12 Nm
Engine Mounts - All7 specs
- Electrical Connector Bolts6 lb-ft8 Nm
- Engine Mount Through-Bolt63 lb-ft85 Nm
- Engine Mount-to-Block Bolts48 lb-ft65 Nm
- Engine Mount-to-Frame Bolts44 lb-ft60 Nm
- Gasket Surface BoltsClean mating surfaces17 lb-ft23 Nm
- Sensor Mounting Bolts9 lb-ft12 Nm
- Transmission Mount Bolts48 lb-ft65 Nm
Engine R&R13 specs
- AC Compressor Bolts18 lb-ft25 Nm
- Alternator Mounting Bolts37 lb-ft50 Nm
- Electrical Connector Bolts6 lb-ft8 Nm
- Engine Mount-to-Block Bolts48 lb-ft65 Nm
- Engine Mount-to-Frame Bolts55 lb-ft75 Nm
- Exhaust Manifold NutsApply anti-seize, work hot-to-cold18 lb-ft25 Nm
- Flywheel BoltsOften TTY, tighten in star pattern33 lb-ft45 Nm
- Gasket Surface BoltsClean mating surfaces17 lb-ft23 Nm
- Oil Drain PlugUse new crush washer18 lb-ft25 Nm
- Power Steering Pump Bolts18 lb-ft25 Nm
- Sensor Mounting Bolts9 lb-ft12 Nm
- Starter Mounting Bolt37 lb-ft50 Nm
- Transmission-to-Engine Bolts41 lb-ft55 Nm
Engine Rebuild21 specs
- Balance Shaft Bolts18 lb-ft25 Nm
- Camshaft Bearing Cap BoltsTighten in sequence, 3 passes10 lb-ft14 Nm
- Camshaft Cap BoltsTighten in sequence from center outward, multiple passes10 lb-ft14 Nm
- Connecting Rod BoltsTTY - critical torque plus angle33 lb-ft45 Nm
- Crankshaft Pulley BoltOften TTY - check spec, may require impact133 lb-ft180 Nm
- Cylinder Head BoltsTTY - tighten in sequence plus angle48 lb-ft65 Nm
- Electrical Connector Bolts6 lb-ft8 Nm
- Exhaust Manifold NutsApply anti-seize, work hot-to-cold18 lb-ft25 Nm
- Flywheel BoltsOften TTY, tighten in star pattern70 lb-ft95 Nm
- Gasket Surface BoltsClean mating surfaces8 lb-ft11 Nm
- Intake Manifold Bolt9 lb-ft12 Nm
- Main Bearing Cap BoltsTTY - tighten in sequence plus angle55 lb-ft75 Nm
- Oil Drain PlugUse new crush washer18 lb-ft25 Nm
- Oil Pan BoltTighten in sequence9 lb-ft12 Nm
- Oil Pump Bolts18 lb-ft25 Nm
- Oil Pump Pickup Tube9 lb-ft12 Nm
- Sensor Mounting Bolts9 lb-ft12 Nm
- Timing Chain Guide BoltsReplace if worn9 lb-ft12 Nm
- Timing Chain Tensioner BoltInstall with pin/clip to compress18 lb-ft25 Nm
- Timing Cover Bolts - 8mmTighten in sequence18 lb-ft25 Nm
- Valve Cover BoltsTighten in sequence7 lb-ft10 Nm
Exhaust Manifold8 specs
- Electrical Connector Bolts6 lb-ft8 Nm
- Exhaust Flange BoltApply anti-seize. Verify sequence with the service manual18 lb-ft25 Nm
- Exhaust Manifold NutsApply anti-seize, work hot-to-cold. Verify sequence with the service manual18 lb-ft25 Nm
- Gasket Surface BoltsClean mating surfaces17 lb-ft23 Nm
- Hanger Bolts17 lb-ft23 Nm
- Heat Shield BoltsVerify sequence with the service manual7 lb-ft10 Nm
- O2 SensorAnti-seize threads33 lb-ft45 Nm
- Sensor Mounting Bolts9 lb-ft12 Nm
Exhaust Manifold Gasket3 specs
- Exhaust Manifold NutsApply anti-seize, work hot-to-cold18 lb-ft25 Nm
- Exhaust Manifold StudsIf replacing studs11 lb-ft15 Nm
- Heat Shield Bolts7 lb-ft10 Nm
Fan Belt Replacement3 specs
- Idler Pulley Bolt30 lb-ft40 Nm
- Tensioner Bolt18 lb-ft25 Nm
- Tensioner Pulley Bolt33 lb-ft45 Nm
Flexplate6 specs
- Electrical Connector Bolts6 lb-ft8 Nm
- Flexplate BoltsAutomatic transmissions. Verify sequence with the service manual63 lb-ft85 Nm
- Gasket Surface BoltsClean mating surfaces17 lb-ft23 Nm
- Sensor Mounting Bolts9 lb-ft12 Nm
- Torque Converter BoltsVerify sequence with the service manual37 lb-ft50 Nm
- Transmission-to-Engine BoltsVerify sequence with the service manual41 lb-ft55 Nm
Freeze Plug - Single4 specs
- Electrical Connector Bolts6 lb-ft8 Nm
- Freeze PlugUse sealant on edges7 lb-ft10 Nm
- Gasket Surface BoltsClean mating surfaces17 lb-ft23 Nm
- Sensor Mounting Bolts9 lb-ft12 Nm
Freeze Plugs - All4 specs
- Electrical Connector Bolts6 lb-ft8 Nm
- Freeze PlugUse sealant on edges7 lb-ft10 Nm
- Gasket Surface BoltsClean mating surfaces17 lb-ft23 Nm
- Sensor Mounting Bolts9 lb-ft12 Nm
Front Main Seal8 specs
- Crankshaft Pulley BoltOften TTY, may need impact133 lb-ft180 Nm
- Electrical Connector Bolts6 lb-ft8 Nm
- Gasket Surface BoltsClean mating surfaces17 lb-ft23 Nm
- Oil Drain PlugUse new crush washer26 lb-ft35 Nm
- Oil Pan BoltFront section only9 lb-ft12 Nm
- Sensor Mounting Bolts9 lb-ft12 Nm
- Timing Cover Bolts - 10mmTighten in sequence33 lb-ft45 Nm
- Timing Cover Bolts - 8mmTighten in sequence18 lb-ft25 Nm
Full Engine Tune-Up4 specs
- Ignition Coil Bolt6 lb-ft8 Nm
- Spark Plugs - Aluminum HeadApply anti-seize to threads18 lb-ft25 Nm
- Throttle Body Bolts7 lb-ft10 Nm
- Valve Cover BoltsTighten in sequence7 lb-ft10 Nm
Harmonic Balancer4 specs
- Crankshaft Pulley BoltOften TTY, may need impact. Verify sequence with the service manual133 lb-ft180 Nm
- Electrical Connector Bolts6 lb-ft8 Nm
- Gasket Surface BoltsClean mating surfaces17 lb-ft23 Nm
- Sensor Mounting Bolts9 lb-ft12 Nm
Head Gasket - Single6 specs
- Exhaust Manifold NutsApply anti-seize18 lb-ft25 Nm
- Intake Manifold BoltTighten in sequence18 lb-ft25 Nm
- Cylinder Head Bolts - Step 1Always use new TTY bolts30 lb-ft40 Nm
- Cylinder Head Bolts - Step 2Tighten in sequence59 lb-ft80 Nm
- Cylinder Head Bolts - Step 3Plus 90 degreesTurn 90°
- Cylinder Head Bolts - Step 4Plus 90 degrees66 lb-ft + 90°90 Nm
Head Gaskets - Both15 specs
- Camshaft Cap BoltsTighten in sequence from center outward, multiple passes10 lb-ft14 Nm
- Camshaft Sprocket BoltsHold cam with wrench on hex59 lb-ft80 Nm
- Crankshaft Pulley BoltOften TTY - check spec, may require impact133 lb-ft180 Nm
- Cylinder Head BoltsMulti-step + angle75 lb-ft101 Nm
- Electrical Connector Bolts6 lb-ft8 Nm
- Exhaust Manifold Nuts18 lb-ft25 Nm
- Gasket Surface BoltsClean mating surfaces7 lb-ft10 Nm
- Intake Manifold Bolt7 lb-ft10 Nm
- Oil Drain PlugUse new crush washer18 lb-ft25 Nm
- Rocker Arm BoltsTighten with cam lobe pointing away22 lb-ft30 Nm
- Sensor Mounting Bolts7 lb-ft10 Nm
- Timing Chain Tensioner BoltInstall with pin/clip to compress15 lb-ft20 Nm
- Timing Cover Bolts - 8mmTighten in sequence18 lb-ft25 Nm
- Valve Cover BoltsTighten in sequence7 lb-ft10 Nm
- VVT Solenoid Bolt7 lb-ft10 Nm
Idle Air Control Valve4 specs
- Electrical Connector Bolts6 lb-ft8 Nm
- Gasket Surface BoltsClean mating surfaces17 lb-ft23 Nm
- IAC Valve Screws2 lb-ft3 Nm
- Sensor Mounting Bolts9 lb-ft12 Nm
Idler Pulley4 specs
- Electrical Connector Bolts6 lb-ft8 Nm
- Gasket Surface BoltsClean mating surfaces17 lb-ft23 Nm
- Idler Pulley Bolt33 lb-ft45 Nm
- Sensor Mounting Bolts9 lb-ft12 Nm
Intake Manifold7 specs
- Electrical Connector Bolts6 lb-ft8 Nm
- Fuel Rail BoltsVerify sequence with the service manual9 lb-ft12 Nm
- Gasket Surface BoltsClean mating surfaces17 lb-ft23 Nm
- Intake Manifold BoltTighten in sequence from center out. Verify sequence with the service manual8 lb-ft11 Nm
- PCV ValveVerify sequence with the service manual6 lb-ft8 Nm
- Sensor Mounting Bolts9 lb-ft12 Nm
- Throttle Body BoltsVerify sequence with the service manual7 lb-ft10 Nm
Intake Manifold Gasket3 specs
- Fuel Rail Bolts9 lb-ft12 Nm
- Intake Manifold BoltTighten in sequence from center out8 lb-ft11 Nm
- Throttle Body Bolts7 lb-ft10 Nm
Intercooler5 specs
- Charge Pipe Clamps3 lb-ft4 Nm
- Electrical Connector Bolts6 lb-ft8 Nm
- Gasket Surface BoltsClean mating surfaces17 lb-ft23 Nm
- Intercooler Mounting Bolts11 lb-ft15 Nm
- Sensor Mounting Bolts9 lb-ft12 Nm
Knock Sensor4 specs
- Electrical Connector Bolts6 lb-ft8 Nm
- Gasket Surface BoltsClean mating surfaces17 lb-ft23 Nm
- Knock SensorTorque critical for function15 lb-ft20 Nm
- Sensor Mounting Bolts9 lb-ft12 Nm
Lifter - Single7 specs
- Electrical Connector Bolts6 lb-ft8 Nm
- Gasket Surface BoltsClean mating surfaces7 lb-ft10 Nm
- Intake Manifold Bolt18 lb-ft25 Nm
- Rocker Arm BoltsTighten with cam lobe pointing away22 lb-ft30 Nm
- Rocker Arm Shaft BoltsTighten evenly in sequence18 lb-ft25 Nm
- Sensor Mounting Bolts9 lb-ft12 Nm
- Valve Cover BoltsTighten in sequence7 lb-ft10 Nm
Lifters/Tappets - All10 specs
- Camshaft Bearing Cap BoltsTighten in sequence, 3 passes10 lb-ft14 Nm
- Camshaft Cap BoltsTighten in sequence from center outward, multiple passes10 lb-ft14 Nm
- Camshaft Position Sensor7 lb-ft10 Nm
- Electrical Connector Bolts6 lb-ft8 Nm
- Gasket Surface BoltsClean mating surfaces7 lb-ft10 Nm
- Intake Manifold Bolt18 lb-ft25 Nm
- Rocker Arm BoltsTighten with cam lobe pointing away22 lb-ft30 Nm
- Rocker Arm Shaft BoltsTighten evenly in sequence18 lb-ft25 Nm
- Sensor Mounting Bolts9 lb-ft12 Nm
- Valve Cover BoltsTighten in sequence7 lb-ft10 Nm
Long Block Replacement16 specs
- Camshaft Cap BoltsTighten in sequence from center outward, multiple passes10 lb-ft14 Nm
- Connecting Rod BoltsTTY - critical torque plus angle33 lb-ft45 Nm
- Cylinder Head BoltsTTY - tighten in sequence plus angle48 lb-ft65 Nm
- Electrical Connector Bolts6 lb-ft8 Nm
- Exhaust Manifold NutsApply anti-seize, work hot-to-cold18 lb-ft25 Nm
- Flywheel BoltsOften TTY, tighten in star pattern70 lb-ft95 Nm
- Gasket Surface BoltsClean mating surfaces7 lb-ft10 Nm
- Intake Manifold Bolt9 lb-ft12 Nm
- Main Bearing Cap BoltsTTY - tighten in sequence plus angle55 lb-ft75 Nm
- Oil Drain PlugUse new crush washer18 lb-ft25 Nm
- Oil Pan Bolt9 lb-ft12 Nm
- Sensor Mounting Bolts9 lb-ft12 Nm
- Timing Chain Tensioner BoltInstall with pin/clip to compress18 lb-ft25 Nm
- Timing Cover Bolts - 8mmTighten in sequence18 lb-ft25 Nm
- Transmission-to-Engine Bolts33 lb-ft45 Nm
- Valve Cover BoltsTighten in sequence7 lb-ft10 Nm
Main Bearings9 specs
- Electrical Connector Bolts6 lb-ft8 Nm
- Flywheel BoltsOften TTY, tighten in star pattern. Verify sequence with the service manual70 lb-ft95 Nm
- Gasket Surface BoltsClean mating surfaces17 lb-ft23 Nm
- Main Bearing Cap BoltsTTY - tighten in sequence plus angle. Verify sequence with the service manual55 lb-ft75 Nm
- Oil Drain PlugUse new crush washer. Verify sequence with the service manual18 lb-ft25 Nm
- Oil Pan BoltTighten in sequence. Verify sequence with the service manual9 lb-ft12 Nm
- Oil Pump Pickup TubeVerify sequence with the service manual9 lb-ft12 Nm
- Sensor Mounting Bolts9 lb-ft12 Nm
- Transmission-to-Engine BoltsVerify sequence with the service manual33 lb-ft45 Nm
Manifold Absolute Pressure Sensor4 specs
- Electrical Connector Bolts6 lb-ft8 Nm
- Gasket Surface BoltsClean mating surfaces17 lb-ft23 Nm
- MAP Sensor Screws2 lb-ft3 Nm
- Sensor Mounting Bolts9 lb-ft12 Nm
Mass Air Flow Sensor5 specs
- Air Intake Clamps2 lb-ft3 Nm
- Electrical Connector Bolts6 lb-ft8 Nm
- Gasket Surface BoltsClean mating surfaces17 lb-ft23 Nm
- MAF Sensor Screws2 lb-ft3 Nm
- Sensor Mounting Bolts9 lb-ft12 Nm
Oil Change2 specs
- Oil Drain PlugUse new crush washer18 lb-ft25 Nm
- Oil Filter Housing CapFor cartridge-type filters18 lb-ft25 Nm
Oil Level Sensor5 specs
- Electrical Connector Bolts6 lb-ft8 Nm
- Gasket Surface BoltsClean mating surfaces17 lb-ft23 Nm
- Oil Level Sensor11 lb-ft15 Nm
- Oil Pan BoltIf access needed9 lb-ft12 Nm
- Sensor Mounting Bolts9 lb-ft12 Nm
Oil Pan Gasket2 specs
- Oil Drain PlugUse new crush washer18 lb-ft25 Nm
- Oil Pan BoltTighten in sequence from center outward9 lb-ft12 Nm
Oil Pan Replacement6 specs
- Electrical Connector Bolts6 lb-ft8 Nm
- Gasket Surface BoltsClean mating surfaces17 lb-ft23 Nm
- Oil Drain PlugUse new crush washer18 lb-ft25 Nm
- Oil Pan BoltTighten in sequence9 lb-ft12 Nm
- Oil Pump Pickup Tube9 lb-ft12 Nm
- Sensor Mounting Bolts9 lb-ft12 Nm
Oil Pressure Sensor4 specs
- Electrical Connector Bolts6 lb-ft8 Nm
- Gasket Surface BoltsClean mating surfaces17 lb-ft23 Nm
- Oil Pressure SensorUse thread sealant15 lb-ft20 Nm
- Sensor Mounting Bolts9 lb-ft12 Nm
Oil Pump8 specs
- Electrical Connector Bolts6 lb-ft8 Nm
- Gasket Surface BoltsClean mating surfaces17 lb-ft23 Nm
- Oil Drain PlugUse new crush washer18 lb-ft25 Nm
- Oil Pan Bolt9 lb-ft12 Nm
- Oil Pump Bolts18 lb-ft25 Nm
- Oil Pump Pickup Tube9 lb-ft12 Nm
- Sensor Mounting Bolts9 lb-ft12 Nm
- Timing Cover Bolts - 8mmTighten in sequence18 lb-ft25 Nm
PCV Valve4 specs
- Electrical Connector Bolts6 lb-ft8 Nm
- Gasket Surface BoltsClean mating surfaces17 lb-ft23 Nm
- PCV ValveHand tight usually6 lb-ft8 Nm
- Sensor Mounting Bolts9 lb-ft12 Nm
Piston - Single7 specs
- Connecting Rod BoltsTTY - critical torque plus angle15 lb-ft20 Nm
- Cylinder Head BoltsTTY - tighten in sequence plus angle48 lb-ft65 Nm
- Electrical Connector Bolts6 lb-ft8 Nm
- Gasket Surface BoltsClean mating surfaces17 lb-ft23 Nm
- Oil Drain PlugUse new crush washer18 lb-ft25 Nm
- Oil Pan Bolt9 lb-ft12 Nm
- Sensor Mounting Bolts9 lb-ft12 Nm
Piston Rings - All9 specs
- Connecting Rod BoltsTTY - critical torque plus angle33 lb-ft45 Nm
- Cylinder Head BoltsTTY - tighten in sequence plus angle22 lb-ft30 Nm
- Electrical Connector Bolts6 lb-ft8 Nm
- Gasket Surface BoltsClean mating surfaces17 lb-ft23 Nm
- Main Bearing Cap BoltsTTY - tighten in sequence plus angle22 lb-ft30 Nm
- Oil Drain PlugUse new crush washer18 lb-ft25 Nm
- Oil Pan BoltTighten in sequence9 lb-ft12 Nm
- Oil Pump Pickup Tube9 lb-ft12 Nm
- Sensor Mounting Bolts9 lb-ft12 Nm
Pistons - All9 specs
- Connecting Rod BoltsTTY - critical torque plus angle33 lb-ft45 Nm
- Cylinder Head BoltsTTY - tighten in sequence plus angle22 lb-ft30 Nm
- Electrical Connector Bolts6 lb-ft8 Nm
- Gasket Surface BoltsClean mating surfaces17 lb-ft23 Nm
- Main Bearing Cap BoltsTTY - tighten in sequence plus angle22 lb-ft30 Nm
- Oil Drain PlugUse new crush washer18 lb-ft25 Nm
- Oil Pan Bolt9 lb-ft12 Nm
- Oil Pump Pickup Tube9 lb-ft12 Nm
- Sensor Mounting Bolts9 lb-ft12 Nm
Rear Main Seal9 specs
- Electrical Connector Bolts6 lb-ft8 Nm
- Flexplate BoltsAutomatic transmissions63 lb-ft85 Nm
- Flywheel BoltsOften TTY, tighten in star pattern35 lb-ft48 Nm
- Gasket Surface BoltsClean mating surfaces7 lb-ft10 Nm
- Oil Drain PlugUse new crush washer18 lb-ft25 Nm
- Oil Pan BoltRear section9 lb-ft12 Nm
- Rear Main Seal Housing9 lb-ft12 Nm
- Sensor Mounting Bolts9 lb-ft12 Nm
- Transmission-to-Engine Bolts33 lb-ft45 Nm
Rocker Arms - All7 specs
- Electrical Connector Bolts6 lb-ft8 Nm
- Gasket Surface BoltsClean mating surfaces7 lb-ft10 Nm
- Intake Manifold BoltIf pushrods18 lb-ft25 Nm
- Rocker Arm BoltsTighten with cam lobe pointing away22 lb-ft30 Nm
- Rocker Arm Shaft BoltsTighten evenly in sequence18 lb-ft25 Nm
- Sensor Mounting Bolts9 lb-ft12 Nm
- Valve Cover BoltsTighten in sequence7 lb-ft10 Nm
Serpentine Belt2 specs
- Belt Tensioner Bolt41 lb-ft55 Nm
- Idler Pulley Bolt33 lb-ft45 Nm
Serpentine Belt Tensioner4 specs
- Belt Tensioner Bolt33 lb-ft45 Nm
- Electrical Connector Bolts6 lb-ft8 Nm
- Gasket Surface BoltsClean mating surfaces17 lb-ft23 Nm
- Sensor Mounting Bolts9 lb-ft12 Nm
Short Block Replacement12 specs
- Connecting Rod BoltsTTY - critical torque plus angle33 lb-ft45 Nm
- Crankshaft Pulley BoltOften TTY - check spec, may require impact133 lb-ft180 Nm
- Electrical Connector Bolts6 lb-ft8 Nm
- Flywheel BoltsOften TTY, tighten in star pattern70 lb-ft95 Nm
- Gasket Surface BoltsClean mating surfaces17 lb-ft23 Nm
- Main Bearing Cap BoltsTTY - tighten in sequence plus angle22 lb-ft30 Nm
- Oil Drain PlugUse new crush washer18 lb-ft25 Nm
- Oil Pan Bolt9 lb-ft12 Nm
- Oil Pump Bolts18 lb-ft25 Nm
- Sensor Mounting Bolts9 lb-ft12 Nm
- Timing Cover Bolts - 8mmTighten in sequence18 lb-ft25 Nm
- Transmission-to-Engine Bolts33 lb-ft45 Nm
Throttle Body2 specs
- Air Intake Hose Clamps2 lb-ft3 Nm
- Throttle Body Bolts7 lb-ft10 Nm
Throttle Position Sensor4 specs
- Electrical Connector Bolts6 lb-ft8 Nm
- Gasket Surface BoltsClean mating surfaces17 lb-ft23 Nm
- Sensor Mounting Bolts9 lb-ft12 Nm
- TPS Screws2 lb-ft3 Nm
Timing Chain5 specs
- Camshaft Sprocket Bolts59 lb-ft80 Nm
- Crankshaft Pulley BoltOften TTY - check specs133 lb-ft + 90°180 Nm
- Timing Chain Guide Bolts9 lb-ft12 Nm
- Timing Chain Tensioner32 lb-ft43 Nm
- Timing Cover BoltTighten in sequence9 lb-ft12 Nm
Timing Chain Guide11 specs
- Camshaft Sprocket Bolts63 lb-ft86 Nm
- Crankshaft Pulley Bolt150 lb-ft203 Nm
- Electrical Connector Bolts6 lb-ft8 Nm
- Gasket Surface BoltsClean mating surfaces8 lb-ft11 Nm
- Guide Bolts7 lb-ft10 Nm
- Sensor Mounting Bolts9 lb-ft12 Nm
- Tensioner Bolt32 lb-ft43 Nm
- Timing Chain Guide BoltsReplace if worn9 lb-ft12 Nm
- Timing Cover Bolt9 lb-ft12 Nm
- Timing Cover Bolts - 8mmTighten in sequence18 lb-ft25 Nm
- Valve Cover BoltsTighten in sequence7 lb-ft10 Nm
Timing Chain Kit18 specs
- Cam Phaser BoltApply threadlocker, hold cam stationary48 lb-ft65 Nm
- Camshaft Sprocket BoltsHold cam with wrench on hex59 lb-ft80 Nm
- Crankshaft Pulley BoltOften TTY - check spec, may require impact133 lb-ft180 Nm
- Electrical Connector Bolts6 lb-ft8 Nm
- Gasket Surface BoltsClean mating surfaces8 lb-ft11 Nm
- Guide Bolts7 lb-ft10 Nm
- Oil Drain PlugUse new crush washer18 lb-ft25 Nm
- Oil Pump Bolts18 lb-ft25 Nm
- Sensor Mounting Bolts9 lb-ft12 Nm
- Tensioner Bolt17 lb-ft23 Nm
- Timing Chain Guide BoltsReplace if worn9 lb-ft12 Nm
- Timing Chain Idler Sprocket33 lb-ft45 Nm
- Timing Chain Tensioner BoltInstall with pin/clip to compress18 lb-ft25 Nm
- Timing Cover Bolt8 lb-ft11 Nm
- Timing Cover Bolts - 10mmTighten in sequence18 lb-ft25 Nm
- Timing Cover Bolts - 6mmTighten in sequence7 lb-ft10 Nm
- Timing Cover Bolts - 8mmTighten in sequence8 lb-ft11 Nm
- Valve Cover BoltsTighten in sequence7 lb-ft10 Nm
Timing Chain Tensioner11 specs
- Camshaft Sprocket Bolts63 lb-ft86 Nm
- Crankshaft Pulley Bolt150 lb-ft203 Nm
- Electrical Connector Bolts6 lb-ft8 Nm
- Gasket Surface BoltsClean mating surfaces7 lb-ft10 Nm
- Guide Bolts7 lb-ft10 Nm
- Sensor Mounting Bolts9 lb-ft12 Nm
- Tensioner Bolt17 lb-ft23 Nm
- Timing Chain Tensioner BoltInstall with pin/clip to compress18 lb-ft25 Nm
- Timing Cover Bolt8 lb-ft11 Nm
- Timing Cover Bolts - 8mmTighten in sequence8 lb-ft11 Nm
- Valve Cover BoltsTighten in sequence7 lb-ft10 Nm
Transmission Mount7 specs
- Crossmember Bolt59 lb-ft80 Nm
- Drain PlugUse new washer29 lb-ft39 Nm
- Fill Plug29 lb-ft39 Nm
- Flywheel BoltsOften TTY, tighten in star pattern70 lb-ft95 Nm
- Transmission Drain PlugUse new crush washer if equipped22 lb-ft30 Nm
- Transmission Mount Bolts48 lb-ft65 Nm
- Transmission Pan BoltsTighten in criss-cross pattern9 lb-ft12 Nm
Turbo Wastegate Actuator4 specs
- Electrical Connector Bolts6 lb-ft8 Nm
- Gasket Surface BoltsClean mating surfaces17 lb-ft23 Nm
- Sensor Mounting Bolts9 lb-ft12 Nm
- Wastegate Actuator Bolts11 lb-ft15 Nm
Turbocharger10 specs
- Coolant Line Fittings11 lb-ft15 Nm
- Electrical Connector Bolts6 lb-ft8 Nm
- Exhaust Manifold NutsApply anti-seize, work hot-to-cold18 lb-ft25 Nm
- Gasket Surface BoltsClean mating surfaces17 lb-ft23 Nm
- Heat Shield Bolts7 lb-ft10 Nm
- Oil Feed LineUse new crush washers15 lb-ft20 Nm
- Oil Return Line7 lb-ft10 Nm
- Sensor Mounting Bolts9 lb-ft12 Nm
- Turbo-to-Downpipe Bolts18 lb-ft25 Nm
- Turbo-to-Manifold BoltsApply anti-seize18 lb-ft25 Nm
Valve Adjustment6 specs
- Electrical Connector Bolts6 lb-ft8 Nm
- Gasket Surface BoltsClean mating surfaces17 lb-ft23 Nm
- Rocker Arm BoltsTighten with cam lobe pointing away22 lb-ft30 Nm
- Sensor Mounting Bolts9 lb-ft12 Nm
- Valve Cover BoltsTighten in sequence7 lb-ft10 Nm
- Valve Lash Adjusting Screw Lock NutHold screw while tightening15 lb-ft20 Nm
Valve Cover Gasket - Single2 specs
- Spark Plug Tube SealsIf equipped with separate seals9 lb-ft12 Nm
- Valve Cover BoltsTighten in sequence7 lb-ft10 Nm
Valve Cover Gaskets - Both7 specs
- Electrical Connector Bolts6 lb-ft8 Nm
- Gasket Surface BoltsClean mating surfaces7 lb-ft10 Nm
- Ignition Coil Bolt6 lb-ft8 Nm
- Intake Manifold BoltIf required18 lb-ft25 Nm
- Sensor Mounting Bolts9 lb-ft12 Nm
- Spark Plugs - Aluminum HeadApply anti-seize to threads15 lb-ft20 Nm
- Valve Cover BoltsTighten in sequence7 lb-ft10 Nm
Valve Job - Complete12 specs
- Camshaft Cap BoltsTighten in sequence from center outward, multiple passes10 lb-ft14 Nm
- Camshaft Sprocket BoltsHold cam with wrench on hex44 lb-ft60 Nm
- Cylinder Head BoltsTTY - tighten in sequence plus angle30 lb-ft40 Nm
- Electrical Connector Bolts6 lb-ft8 Nm
- Exhaust Manifold NutsApply anti-seize, work hot-to-cold18 lb-ft25 Nm
- Gasket Surface BoltsClean mating surfaces8 lb-ft11 Nm
- Intake Manifold Bolt9 lb-ft12 Nm
- Rocker Arm BoltsTighten with cam lobe pointing away22 lb-ft30 Nm
- Sensor Mounting Bolts9 lb-ft12 Nm
- Timing Chain Tensioner BoltInstall with pin/clip to compress18 lb-ft25 Nm
- Timing Cover Bolts - 8mmTighten in sequence18 lb-ft25 Nm
- Valve Cover BoltsTighten in sequence7 lb-ft10 Nm
Valve Seals8 specs
- Camshaft Cap BoltsTighten in sequence from center outward, multiple passes10 lb-ft14 Nm
- Electrical Connector Bolts6 lb-ft8 Nm
- Gasket Surface BoltsClean mating surfaces7 lb-ft10 Nm
- Rocker Arm BoltsTighten with cam lobe pointing away22 lb-ft30 Nm
- Rocker Arm Shaft BoltsTighten evenly in sequence18 lb-ft25 Nm
- Sensor Mounting Bolts9 lb-ft12 Nm
- Spark Plugs - Aluminum HeadApply anti-seize to threads18 lb-ft25 Nm
- Valve Cover BoltsTighten in sequence7 lb-ft10 Nm
Valve Spring - Single6 specs
- Electrical Connector Bolts6 lb-ft8 Nm
- Gasket Surface BoltsClean mating surfaces7 lb-ft10 Nm
- Rocker Arm BoltsTighten with cam lobe pointing away22 lb-ft30 Nm
- Sensor Mounting Bolts9 lb-ft12 Nm
- Spark Plugs - Aluminum HeadApply anti-seize to threads18 lb-ft25 Nm
- Valve Cover BoltsTighten in sequence7 lb-ft10 Nm
Valve Springs - All8 specs
- Camshaft Cap BoltsTighten in sequence from center outward, multiple passes10 lb-ft14 Nm
- Electrical Connector Bolts6 lb-ft8 Nm
- Gasket Surface BoltsClean mating surfaces7 lb-ft10 Nm
- Rocker Arm BoltsTighten with cam lobe pointing away22 lb-ft30 Nm
- Rocker Arm Shaft BoltsTighten evenly in sequence18 lb-ft25 Nm
- Sensor Mounting Bolts9 lb-ft12 Nm
- Spark Plugs - Aluminum HeadApply anti-seize to threads18 lb-ft25 Nm
- Valve Cover BoltsTighten in sequence7 lb-ft10 Nm
Variable Valve Timing Actuator10 specs
- Cam Phaser BoltApply threadlocker, hold cam stationary48 lb-ft65 Nm
- Camshaft Sprocket BoltsHold cam with wrench on hex59 lb-ft80 Nm
- Crankshaft Pulley BoltOften TTY - check spec, may require impact133 lb-ft180 Nm
- Electrical Connector Bolts6 lb-ft8 Nm
- Gasket Surface BoltsClean mating surfaces7 lb-ft10 Nm
- Sensor Mounting Bolts9 lb-ft12 Nm
- Timing Chain Tensioner BoltInstall with pin/clip to compress18 lb-ft25 Nm
- Timing Cover Bolts - 8mmTighten in sequence18 lb-ft25 Nm
- Valve Cover BoltsTighten in sequence7 lb-ft10 Nm
- VVT Solenoid Bolt7 lb-ft10 Nm
VVT Solenoid - Single5 specs
- Electrical Connector Bolts6 lb-ft8 Nm
- Gasket Surface BoltsClean mating surfaces7 lb-ft10 Nm
- Sensor Mounting Bolts9 lb-ft12 Nm
- Valve Cover BoltsTighten in sequence7 lb-ft10 Nm
- VVT Solenoid Bolt7 lb-ft10 Nm
VVT Solenoids - All6 specs
- Camshaft Position Sensor7 lb-ft10 Nm
- Electrical Connector Bolts6 lb-ft8 Nm
- Gasket Surface BoltsClean mating surfaces7 lb-ft10 Nm
- Sensor Mounting Bolts9 lb-ft12 Nm
- Valve Cover BoltsTighten in sequence7 lb-ft10 Nm
- VVT Solenoid Bolt7 lb-ft10 Nm

Cooling

Coolant Bypass Pipe8 specs
- Bleed ScrewOpen during fill6 lb-ft8 Nm
- Coolant Drain Plug11 lb-ft15 Nm
- Drain PetcockHand tight6 lb-ft8 Nm
- Fan Bolts9 lb-ft12 Nm
- Hose Clamps2 lb-ft3 Nm
- Pump BoltsTorque in sequence21 lb-ft28 Nm
- Thermostat Housing Bolt11 lb-ft15 Nm
- Water Pump BoltsTighten in criss-cross pattern18 lb-ft25 Nm
Coolant Flush12 specs
- Air Box Clips4 lb-ft5 Nm
- Bleed ScrewOpen during fill6 lb-ft8 Nm
- Block Drain PlugIf equipped, use new washer18 lb-ft25 Nm
- Connector Bolts6 lb-ft8 Nm
- Coolant Hose Clamps3 lb-ft4 Nm
- Drain Petcock4 lb-ft5 Nm
- Drain Plug11 lb-ft15 Nm
- Hose Clamps3 lb-ft5 Nm
- Oil Drain PlugUse new crush washer18 lb-ft25 Nm
- Pump Bolts21 lb-ft28 Nm
- Radiator CapHand tight1 lb-ft1 Nm
- Wheel Lug NutsTorque in star pattern112 lb-ft152 Nm
Coolant Reservoir9 specs
- Bleed ScrewOpen during fill6 lb-ft8 Nm
- Coolant Drain Plug11 lb-ft15 Nm
- Drain PetcockHand tight6 lb-ft8 Nm
- Fan Bolts9 lb-ft12 Nm
- Hose ClampsDo not overtighten3 lb-ft4 Nm
- Pump BoltsTorque in sequence21 lb-ft28 Nm
- Reservoir Mounting Bolts6 lb-ft8 Nm
- Thermostat Housing Bolt7 lb-ft10 Nm
- Water Pump BoltsTighten in criss-cross pattern18 lb-ft25 Nm
Coolant Temperature Sensor7 specs
- Bleed ScrewOpen during fill6 lb-ft8 Nm
- Coolant Drain Plug11 lb-ft15 Nm
- Drain PetcockHand tight6 lb-ft8 Nm
- Fan Bolts9 lb-ft12 Nm
- Hose Clamps2 lb-ft3 Nm
- Pump BoltsTorque in sequence21 lb-ft28 Nm
- Thermostat Housing Bolt11 lb-ft15 Nm
Cooling Fan Assembly6 specs
- Coolant Drain Plug11 lb-ft15 Nm
- Drain PetcockHand tight6 lb-ft8 Nm
- Fan Bolts9 lb-ft12 Nm
- Hose Clamps2 lb-ft3 Nm
- Pump BoltsTorque in sequence21 lb-ft28 Nm
- Thermostat Housing Bolt11 lb-ft15 Nm
Cooling Fan Clutch6 specs
- Drain PetcockHand tight6 lb-ft8 Nm
- Fan Bolts9 lb-ft12 Nm
- Hose Clamps2 lb-ft3 Nm
- Pump BoltsTorque in sequence21 lb-ft28 Nm
- Thermostat Housing Bolt11 lb-ft15 Nm
- Water Pump BoltsTighten in criss-cross pattern18 lb-ft25 Nm
Cooling Fan Motor7 specs
- Drain PetcockHand tight6 lb-ft8 Nm
- Electrical Connector4 lb-ft5 Nm
- Fan Bolts9 lb-ft12 Nm
- Fan Motor Bolts6 lb-ft8 Nm
- Hose ClampsDo not overtighten3 lb-ft4 Nm
- Pump BoltsTorque in sequence21 lb-ft28 Nm
- Thermostat Housing Bolt7 lb-ft10 Nm
Cooling Fan Relay4 specs
- Drain PetcockHand tight6 lb-ft8 Nm
- Fan Bolts9 lb-ft12 Nm
- Pump BoltsTorque in sequence21 lb-ft28 Nm
- Thermostat Housing Bolt11 lb-ft15 Nm
Engine Oil Cooler7 specs
- Coolant Drain Plug11 lb-ft15 Nm
- Drain PetcockHand tight6 lb-ft8 Nm
- Fan Bolts9 lb-ft12 Nm
- Hose Clamps2 lb-ft3 Nm
- Pump BoltsTorque in sequence21 lb-ft28 Nm
- Thermostat Housing Bolt11 lb-ft15 Nm
- Water Pump BoltsTighten in criss-cross pattern18 lb-ft25 Nm
Heater Control Valve6 specs
- Drain PetcockHand tight6 lb-ft8 Nm
- Fan Bolts9 lb-ft12 Nm
- Hose Clamps2 lb-ft3 Nm
- Pump BoltsTorque in sequence7 lb-ft10 Nm
- Thermostat Housing Bolt7 lb-ft10 Nm
- Valve Mounting6 lb-ft8 Nm
Heater Core8 specs
- Dashboard Screws2 lb-ft3 Nm
- Drain PetcockHand tight6 lb-ft8 Nm
- Fan Bolts9 lb-ft12 Nm
- Heater Core Mounting6 lb-ft8 Nm
- Heater Hose Clamps2 lb-ft3 Nm
- Hose ClampsDo not overtighten3 lb-ft4 Nm
- Pump BoltsTorque in sequence7 lb-ft10 Nm
- Thermostat Housing Bolt7 lb-ft10 Nm
Heater Hoses6 specs
- Coolant Drain Plug11 lb-ft15 Nm
- Drain PetcockHand tight6 lb-ft8 Nm
- Fan Bolts9 lb-ft12 Nm
- Hose Clamps2 lb-ft3 Nm
- Pump BoltsTorque in sequence7 lb-ft10 Nm
- Thermostat Housing Bolt11 lb-ft15 Nm
Radiator4 specs
- Drain PetcockPlastic - hand tight4 lb-ft5 Nm
- Radiator Mounting BoltDo not overtighten plastic mounts9 lb-ft12 Nm
- Transmission Cooler LinesIf equipped18 lb-ft25 Nm
- Upper/Lower Hose Clamps2 lb-ft3 Nm
Radiator Cap5 specs
- Drain PetcockHand tight6 lb-ft8 Nm
- Fan Bolts9 lb-ft12 Nm
- Pump BoltsTorque in sequence21 lb-ft28 Nm
- Thermostat Housing Bolt11 lb-ft15 Nm
- Water Pump BoltsTighten in criss-cross pattern18 lb-ft25 Nm
Radiator Hose - Lower5 specs
- Drain PetcockHand tight6 lb-ft8 Nm
- Fan Bolts9 lb-ft12 Nm
- Hose Clamps2 lb-ft3 Nm
- Pump BoltsTorque in sequence21 lb-ft28 Nm
- Thermostat Housing Bolt7 lb-ft10 Nm
Radiator Hose - Upper5 specs
- Drain PetcockHand tight6 lb-ft8 Nm
- Fan Bolts9 lb-ft12 Nm
- Hose Clamps2 lb-ft3 Nm
- Pump BoltsTorque in sequence21 lb-ft28 Nm
- Thermostat Housing Bolt7 lb-ft10 Nm
Radiator Hoses - Both7 specs
- Coolant Drain Plug11 lb-ft15 Nm
- Drain PetcockHand tight6 lb-ft8 Nm
- Fan Bolts9 lb-ft12 Nm
- Hose Clamps2 lb-ft3 Nm
- Pump BoltsTorque in sequence21 lb-ft28 Nm
- Thermostat Housing Bolt11 lb-ft15 Nm
- Water Pump BoltsTighten in criss-cross pattern18 lb-ft25 Nm
Radiator Removal and Service4 specs
- Drain PetcockPlastic - hand-tight only4 lb-ft5 Nm
- Fan Shroud Bolts7 lb-ft10 Nm
- Radiator Mounting BoltDo not overtighten plastic mounts9 lb-ft12 Nm
- Transmission Cooler LinesIf equipped, use new washers18 lb-ft25 Nm
Thermostat2 specs
- Coolant Temperature SensorUse thread sealant15 lb-ft20 Nm
- Thermostat Housing Bolt11 lb-ft15 Nm
Thermostat Housing8 specs
- Coolant Drain Plug11 lb-ft15 Nm
- Coolant Hose Clamps3 lb-ft5 Nm
- Drain PetcockHand tight6 lb-ft8 Nm
- Fan Bolts9 lb-ft12 Nm
- Hose Clamps2 lb-ft3 Nm
- Pump BoltsTorque in sequence21 lb-ft28 Nm
- Thermostat Housing Bolt11 lb-ft15 Nm
- Water Pump BoltsTighten in criss-cross pattern18 lb-ft25 Nm
Water Pump3 specs
- Hose ClampsSpring clamps preferred2 lb-ft3 Nm
- Thermostat Housing Bolt11 lb-ft15 Nm
- Water Pump BoltsTighten in criss-cross pattern18 lb-ft25 Nm

Ignition

Ignition Coil - Single3 specs
- Connector Bolts6 lb-ft8 Nm
- Ignition Coil Bolt6 lb-ft8 Nm
- Spark Plugs - Aluminum HeadApply anti-seize to threads18 lb-ft25 Nm
Ignition Coils - All3 specs
- Connector Bolts6 lb-ft8 Nm
- Ignition Coil Bolt6 lb-ft8 Nm
- Spark Plugs - Aluminum HeadApply anti-seize to threads18 lb-ft25 Nm
Ignition Control Module3 specs
- Connector Bolts6 lb-ft8 Nm
- Ignition Coil Bolt6 lb-ft8 Nm
- Spark Plugs - Aluminum HeadApply anti-seize to threads18 lb-ft25 Nm
Ignition Lock Cylinder3 specs
- Connector Bolts6 lb-ft8 Nm
- Ignition Coil Bolt6 lb-ft8 Nm
- Spark Plugs - Aluminum HeadApply anti-seize to threads18 lb-ft25 Nm
Ignition Switch3 specs
- Connector Bolts6 lb-ft8 Nm
- Steering Column Bolts18 lb-ft25 Nm
- Switch Mounting Screws4 lb-ft5 Nm
Spark Plugs8 specs
- Air Box Clips4 lb-ft5 Nm
- Connector Bolts6 lb-ft8 Nm
- Engine Cover Clips2 lb-ft3 Nm
- Ignition Coil Bolt6 lb-ft8 Nm
- Oil Drain PlugUse new crush washer18 lb-ft25 Nm
- Spark PlugGap before install17 lb-ft23 Nm
- Spark Plugs - Aluminum HeadApply anti-seize to threads18 lb-ft24 Nm
- Wheel Lug NutsTorque in star pattern112 lb-ft152 Nm

Fuel system

Charcoal Canister5 specs
- Filter Bracket9 lb-ft12 Nm
- Fuel Line FittingsUse new O-rings18 lb-ft25 Nm
- Hose Clamps2 lb-ft3 Nm
- Pressure Regulator Screws6 lb-ft8 Nm
- Pump Mounting7 lb-ft10 Nm
EVAP Purge Valve5 specs
- Filter Bracket9 lb-ft12 Nm
- Fuel Line FittingsUse new O-rings18 lb-ft25 Nm
- Hose Clamps2 lb-ft3 Nm
- Pressure Regulator Screws6 lb-ft8 Nm
- Pump Mounting12 lb-ft16 Nm
EVAP Vent Valve5 specs
- Filter Bracket9 lb-ft12 Nm
- Fuel Line FittingsUse new O-rings18 lb-ft25 Nm
- Hose Clamps2 lb-ft3 Nm
- Pressure Regulator Screws6 lb-ft8 Nm
- Pump Mounting12 lb-ft16 Nm
Fuel Cap4 specs
- Filter Bracket9 lb-ft12 Nm
- Fuel Line FittingsUse new O-rings18 lb-ft25 Nm
- Pressure Regulator Screws6 lb-ft8 Nm
- Pump Mounting7 lb-ft10 Nm
Fuel Filler Neck6 specs
- Filler Neck Bolts7 lb-ft10 Nm
- Filter Bracket9 lb-ft12 Nm
- Fuel Rail Bolts7 lb-ft10 Nm
- Hose Clamps2 lb-ft3 Nm
- Pressure Regulator Screws6 lb-ft8 Nm
- Pump Mounting7 lb-ft10 Nm
Fuel Filter7 specs
- Air Box Clips4 lb-ft5 Nm
- Connector Bolts6 lb-ft8 Nm
- Filter Bracket Bolt12 lb-ft16 Nm
- Fuel Filter Bracket Bolt7 lb-ft10 Nm
- Fuel Line FittingsIf threaded type18 lb-ft25 Nm
- Oil Drain PlugUse new crush washer26 lb-ft35 Nm
- Wheel Lug NutsTorque in star pattern112 lb-ft152 Nm
Fuel Filter - In-Tank6 specs
- Filter Bracket9 lb-ft12 Nm
- Filter Bracket Bolt12 lb-ft16 Nm
- Fuel Line FittingsUse new O-rings18 lb-ft25 Nm
- Hose Clamps2 lb-ft3 Nm
- Pressure Regulator Screws6 lb-ft8 Nm
- Pump Mounting7 lb-ft10 Nm
Fuel Injector - Single6 specs
- Filter Bracket9 lb-ft12 Nm
- Fuel Line FittingsUse new O-rings18 lb-ft25 Nm
- Fuel Rail Bolts9 lb-ft12 Nm
- Hose Clamps2 lb-ft3 Nm
- Pressure Regulator Screws6 lb-ft8 Nm
- Pump Mounting7 lb-ft10 Nm
Fuel Injector Cleaning6 specs
- Filter Bracket9 lb-ft12 Nm
- Fuel Line FittingsUse new O-rings18 lb-ft25 Nm
- Fuel Rail Bolts9 lb-ft12 Nm
- Hose Clamps2 lb-ft3 Nm
- Pressure Regulator Screws6 lb-ft8 Nm
- Pump Mounting7 lb-ft10 Nm
Fuel Injectors - All6 specs
- Filter Bracket9 lb-ft12 Nm
- Fuel Line FittingsUse new O-rings18 lb-ft25 Nm
- Fuel Rail Bolts9 lb-ft12 Nm
- Hose Clamps2 lb-ft3 Nm
- Pressure Regulator Screws6 lb-ft8 Nm
- Pump Mounting7 lb-ft10 Nm
Fuel Level Sensor5 specs
- Filter Bracket9 lb-ft12 Nm
- Fuel Line FittingsUse new O-rings18 lb-ft25 Nm
- Hose Clamps2 lb-ft3 Nm
- Pressure Regulator Screws6 lb-ft8 Nm
- Pump Mounting7 lb-ft10 Nm
Fuel Line - High Pressure6 specs
- Filter Bracket9 lb-ft12 Nm
- Fuel Line FittingsUse new O-rings18 lb-ft25 Nm
- Fuel Rail Bolts9 lb-ft12 Nm
- Hose Clamps2 lb-ft3 Nm
- Pressure Regulator Screws6 lb-ft8 Nm
- Pump Mounting7 lb-ft10 Nm
Fuel Line - Return6 specs
- Filter Bracket9 lb-ft12 Nm
- Fuel Line FittingsUse new O-rings15 lb-ft20 Nm
- Fuel Rail Bolts9 lb-ft12 Nm
- Hose Clamps2 lb-ft3 Nm
- Pressure Regulator Screws6 lb-ft8 Nm
- Pump Mounting7 lb-ft10 Nm
Fuel Pressure Regulator6 specs
- Filter Bracket9 lb-ft12 Nm
- Fuel Line18 lb-ft25 Nm
- Fuel Rail Bolts7 lb-ft10 Nm
- Pressure Regulator Screws6 lb-ft8 Nm
- Pump Mounting7 lb-ft10 Nm
- Regulator Mounting Screws4 lb-ft5 Nm
Fuel Pump2 specs
- Fuel Pump Module Lock RingUse special tool32 lb-ft43 Nm
- Tank Strap Bolts26 lb-ft35 Nm
Fuel Pump Module7 specs
- Access Cover Screws3 lb-ft5 Nm
- Filter Bracket9 lb-ft12 Nm
- Fuel Line FittingsUse new O-rings18 lb-ft25 Nm
- Fuel Pump Lock RingLock ring tool32 lb-ft43 Nm
- Hose Clamps2 lb-ft3 Nm
- Pressure Regulator Screws6 lb-ft8 Nm
- Pump Mounting7 lb-ft10 Nm
Fuel Rail6 specs
- Filter Bracket9 lb-ft12 Nm
- Fuel Line FittingsUse new O-rings18 lb-ft25 Nm
- Fuel Rail Bolts9 lb-ft12 Nm
- Hose Clamps2 lb-ft3 Nm
- Pressure Regulator Screws6 lb-ft8 Nm
- Pump Mounting7 lb-ft10 Nm
Fuel Tank7 specs
- Filler Neck Clamp3 lb-ft4 Nm
- Filter Bracket9 lb-ft12 Nm
- Fuel Line FittingsUse new O-rings18 lb-ft25 Nm
- Fuel Rail Bolts7 lb-ft10 Nm
- Pressure Regulator Screws6 lb-ft8 Nm
- Pump Mounting7 lb-ft10 Nm
- Tank Strap Bolts26 lb-ft35 Nm
Fuel Tank Strap5 specs
- Filter Bracket9 lb-ft12 Nm
- Fuel Line FittingsUse new O-rings18 lb-ft25 Nm
- Hose Clamps2 lb-ft3 Nm
- Pressure Regulator Screws6 lb-ft8 Nm
- Pump Mounting7 lb-ft10 Nm
High Pressure Fuel Pump5 specs
- Filter Bracket9 lb-ft12 Nm
- Fuel Line FittingsUse new O-rings18 lb-ft25 Nm
- Hose Clamps2 lb-ft3 Nm
- Pressure Regulator Screws6 lb-ft8 Nm
- Pump Mounting16 lb-ft22 Nm

Electrical

Airbag - Driver5 specs
- Airbag Module BoltsTorx - disconnect battery and wait 2 minutes5 lb-ft7 Nm
- Battery Terminal Bolts6 lb-ft8 Nm
- Connector Screws3 lb-ft4 Nm
- Ground Strap BoltsClean contact surfaces7 lb-ft9 Nm
- Steering Wheel Nut40 lb-ft54 Nm
Airbag - Passenger5 specs
- Airbag Module BoltsTorx - disconnect battery and wait 2 minutes5 lb-ft7 Nm
- Battery Terminal Bolts6 lb-ft8 Nm
- Connector Screws3 lb-ft4 Nm
- Dashboard Fasteners3 lb-ft4 Nm
- Ground Strap BoltsClean contact surfaces7 lb-ft9 Nm
Airbag - Side5 specs
- Battery Terminal Bolts6 lb-ft8 Nm
- Connector Screws3 lb-ft4 Nm
- Ground Strap BoltsClean contact surfaces7 lb-ft9 Nm
- Seat Mounting BoltsSafety critical33 lb-ft45 Nm
- Side Airbag Module BoltsTorx5 lb-ft7 Nm
Airbag Module/Computer5 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
- Ground Strap BoltsClean contact surfaces7 lb-ft9 Nm
- Module Mounting Bolts6 lb-ft8 Nm
- Sensor Mounting Bolts7 lb-ft10 Nm
Alternator4 specs
- Alternator Mounting Bolts37 lb-ft50 Nm
- Alternator Pivot Bolt18 lb-ft25 Nm
- Battery Terminal BoltsDo not overtighten6 lb-ft8 Nm
- Serpentine Belt Tensioner41 lb-ft55 Nm
Alternator Belt5 specs
- Alternator Mounting Bolts40 lb-ft55 Nm
- Alternator Pivot Bolt40 lb-ft55 Nm
- Battery Cable Nut9 lb-ft12 Nm
- Connector Screws3 lb-ft4 Nm
- Ground Strap BoltsClean contact surfaces7 lb-ft9 Nm
Amplifier4 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
- Ground Strap BoltsClean contact surfaces7 lb-ft9 Nm
- Module Mounting Bolts6 lb-ft8 Nm
Antenna3 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
- Ground Strap BoltsClean contact surfaces7 lb-ft9 Nm
Backup Camera5 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
- Ground Strap BoltsClean contact surfaces7 lb-ft9 Nm
- Module Mounting Bolts6 lb-ft8 Nm
- Sensor Mounting Bolts7 lb-ft10 Nm
Battery3 specs
- Battery Hold-Down Bolt6 lb-ft8 Nm
- Battery Terminal BoltsDo not overtighten - can crack terminal4 lb-ft6 Nm
- Battery Tray Bolts9 lb-ft12 Nm
Battery Cable - Negative6 specs
- Battery Hold-Down BoltDo not overtighten9 lb-ft12 Nm
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
- Ground Cable Bolt7 lb-ft9 Nm
- Ground Strap BoltsClean contact surfaces7 lb-ft9 Nm
- Sensor Mounting Bolts7 lb-ft10 Nm
Battery Cable - Positive5 specs
- Battery Hold-Down BoltDo not overtighten9 lb-ft12 Nm
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
- Ground Cable Bolt12 lb-ft16 Nm
- Module Mounting Bolts6 lb-ft8 Nm
Battery Cables - Both6 specs
- Battery Hold-Down BoltDo not overtighten9 lb-ft12 Nm
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
- Ground Cable Bolt7 lb-ft9 Nm
- Ground Strap BoltsClean contact surfaces7 lb-ft9 Nm
- Sensor Mounting Bolts7 lb-ft10 Nm
Battery Terminal6 specs
- Battery Hold-Down BoltDo not overtighten9 lb-ft12 Nm
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
- Ground Cable Bolt7 lb-ft9 Nm
- Ground Strap BoltsClean contact surfaces7 lb-ft9 Nm
- Sensor Mounting Bolts7 lb-ft10 Nm
Blower Motor2 specs
- Blower Motor Mounting Screw3 lb-ft4 Nm
- Blower Motor Resistor Screws1.5 lb-ft2 Nm
Blower Motor Control Module4 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
- Ground Strap BoltsClean contact surfaces7 lb-ft9 Nm
- Module Mounting Bolts6 lb-ft8 Nm
Blower Motor Resistor4 specs
- Battery Terminal Bolts6 lb-ft8 Nm
- Connector Screws3 lb-ft4 Nm
- Ground Strap BoltsClean contact surfaces12 lb-ft16 Nm
- Resistor Screws1.5 lb-ft2 Nm
Clock Spring7 specs
- Airbag Module BoltsTorx - disconnect battery first5 lb-ft7 Nm
- Battery Terminal Bolts6 lb-ft8 Nm
- Clock Spring ScrewsAlign marks before removal3 lb-ft4 Nm
- Connector Screws3 lb-ft4 Nm
- Ground Strap BoltsClean contact surfaces7 lb-ft9 Nm
- Steering Column CoversPlastic clips2 lb-ft3 Nm
- Steering Wheel Nut40 lb-ft54 Nm
Combination Switch4 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
- Module Mounting Bolts6 lb-ft8 Nm
- Sensor Mounting Bolts7 lb-ft10 Nm
Dimmer Switch4 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
- Ground Strap BoltsClean contact surfaces12 lb-ft16 Nm
- Module Mounting Bolts6 lb-ft8 Nm
Door Lock Actuator - Front3 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
- Ground Strap BoltsClean contact surfaces12 lb-ft16 Nm
Door Lock Actuator - Rear3 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
- Ground Strap BoltsClean contact surfaces12 lb-ft16 Nm
Fog Light Assembly3 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
- Ground Strap BoltsClean contact surfaces7 lb-ft9 Nm
Fog Light Bulb2 specs
- Connector Screws3 lb-ft4 Nm
- Ground Strap BoltsClean contact surfaces7 lb-ft9 Nm
Fuel Pump Relay6 specs
- Access Cover Screws3 lb-ft5 Nm
- Battery Terminal Bolts6 lb-ft8 Nm
- Connector Screws3 lb-ft4 Nm
- Fuel Pump Lock RingLock ring tool58 lb-ft78 Nm
- Ground Strap BoltsClean contact surfaces7 lb-ft9 Nm
- Relay Socket4 lb-ft5 Nm
Fuse Box - Engine Bay4 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
- Ground Strap BoltsClean contact surfaces7 lb-ft9 Nm
- Module Mounting Bolts6 lb-ft8 Nm
Fuse Box - Interior4 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
- Ground Strap BoltsClean contact surfaces7 lb-ft9 Nm
- Module Mounting Bolts6 lb-ft8 Nm
Headlight Assembly5 specs
- Adjuster Screws2 lb-ft3 Nm
- Battery Terminal Bolts6 lb-ft8 Nm
- Connector Screws3 lb-ft4 Nm
- Ground Strap BoltsClean contact surfaces7 lb-ft9 Nm
- Headlight Assembly Bolts7 lb-ft10 Nm
Headlight Bulb - Single4 specs
- Battery Terminal Bolts6 lb-ft8 Nm
- Bulb Retaining Ring4 lb-ft5 Nm
- Connector Screws3 lb-ft4 Nm
- Ground Strap BoltsClean contact surfaces7 lb-ft9 Nm
Headlight Bulbs - Pair2 specs
- Connector Screws3 lb-ft4 Nm
- Ground Strap BoltsClean contact surfaces7 lb-ft9 Nm
Headlight Switch4 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
- Ground Strap BoltsClean contact surfaces7 lb-ft9 Nm
- Module Mounting Bolts6 lb-ft8 Nm
Heated Seat Module4 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
- Ground Strap BoltsClean contact surfaces7 lb-ft9 Nm
- Module Mounting Bolts6 lb-ft8 Nm
HID Ballast4 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
- Ground Strap BoltsClean contact surfaces7 lb-ft9 Nm
- Module Mounting Bolts6 lb-ft8 Nm
Horn4 specs
- Battery Terminal Bolts6 lb-ft8 Nm
- Connector Screws3 lb-ft4 Nm
- Ground Strap BoltsClean contact surfaces7 lb-ft9 Nm
- Horn Mounting Bolt11 lb-ft15 Nm
Horn Relay2 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
Instrument Cluster4 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
- Ground Strap BoltsClean contact surfaces7 lb-ft9 Nm
- Module Mounting Bolts6 lb-ft8 Nm
LED Headlight Module3 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
- Module Mounting Bolts6 lb-ft8 Nm
Main Relay3 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
- Module Mounting Bolts6 lb-ft8 Nm
Power Antenna Motor3 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
- Ground Strap BoltsClean contact surfaces12 lb-ft16 Nm
Power Mirror Motor3 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
- Ground Strap BoltsClean contact surfaces12 lb-ft16 Nm
Power Seat Motor3 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
- Module Mounting Bolts6 lb-ft8 Nm
Power Window Motor - Front4 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
- Ground Strap BoltsClean contact surfaces12 lb-ft16 Nm
- Module Mounting Bolts6 lb-ft8 Nm
Power Window Motor - Rear4 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
- Ground Strap BoltsClean contact surfaces12 lb-ft16 Nm
- Module Mounting Bolts6 lb-ft8 Nm
Power Window Regulator - Front4 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
- Ground Strap BoltsClean contact surfaces12 lb-ft16 Nm
- Module Mounting Bolts6 lb-ft8 Nm
Power Window Regulator - Rear3 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
- Ground Strap BoltsClean contact surfaces12 lb-ft16 Nm
Radio/Head Unit4 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
- Ground Strap BoltsClean contact surfaces7 lb-ft9 Nm
- Module Mounting Bolts6 lb-ft8 Nm
Relay - Generic4 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
- Ground Strap BoltsClean contact surfaces7 lb-ft9 Nm
- Module Mounting Bolts6 lb-ft8 Nm
Seat Heater Element4 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
- Module Mounting Bolts6 lb-ft8 Nm
- Sensor Mounting Bolts7 lb-ft10 Nm
Side Mirror Assembly3 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
- Ground Strap BoltsClean contact surfaces12 lb-ft16 Nm
Speaker - Dash4 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
- Ground Strap BoltsClean contact surfaces12 lb-ft16 Nm
- Sensor Mounting Bolts7 lb-ft10 Nm
Speaker - Door3 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
- Ground Strap BoltsClean contact surfaces12 lb-ft16 Nm
Speedometer5 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
- Ground Strap BoltsClean contact surfaces12 lb-ft16 Nm
- Module Mounting Bolts6 lb-ft8 Nm
- Sensor Mounting Bolts7 lb-ft10 Nm
Starter3 specs
- Heat Shield BoltsIf equipped7 lb-ft10 Nm
- Starter Mounting BoltLong bolt may need extension37 lb-ft50 Nm
- Starter Solenoid NutFor B+ cable9 lb-ft12 Nm
Starter Solenoid5 specs
- Battery Cable Nut12 lb-ft16 Nm
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
- Ground Strap BoltsClean contact surfaces12 lb-ft16 Nm
- Starter Mounting Bolt33 lb-ft45 Nm
Subwoofer3 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
- Module Mounting Bolts6 lb-ft8 Nm
Tail Light Assembly5 specs
- Battery Terminal Bolts6 lb-ft8 Nm
- Connector Screws3 lb-ft4 Nm
- Ground Strap BoltsClean contact surfaces7 lb-ft9 Nm
- Lens Screws1.5 lb-ft2 Nm
- Tail Light Bolts6 lb-ft8 Nm
Tail Light Bulb2 specs
- Connector Screws3 lb-ft4 Nm
- Ground Strap BoltsClean contact surfaces7 lb-ft9 Nm
Third Brake Light4 specs
- Battery Terminal BoltsDo not overtighten. Verify sequence with the service manual4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
- Ground Strap BoltsClean contact surfaces7 lb-ft9 Nm
- Sensor Mounting BoltsVerify sequence with the service manual7 lb-ft10 Nm
Trunk/Liftgate Actuator2 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
Turn Signal Bulb - Front1 spec
- Connector Screws3 lb-ft4 Nm
Turn Signal Bulb - Rear2 specs
- Connector Screws3 lb-ft4 Nm
- Ground Strap BoltsClean contact surfaces12 lb-ft16 Nm
Turn Signal Switch5 specs
- Battery Terminal Bolts6 lb-ft8 Nm
- Connector Screws3 lb-ft4 Nm
- Ground Strap BoltsClean contact surfaces12 lb-ft16 Nm
- Steering Column Covers1.5 lb-ft2 Nm
- Switch Mounting Screws2 lb-ft3 Nm
Voltage Regulator4 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
- Ground Strap BoltsClean contact surfaces7 lb-ft9 Nm
- Module Mounting Bolts6 lb-ft8 Nm
Washer Pump3 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
- Ground Strap BoltsClean contact surfaces7 lb-ft9 Nm
Washer Reservoir4 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
- Ground Strap BoltsClean contact surfaces7 lb-ft9 Nm
- Sensor Mounting Bolts7 lb-ft10 Nm
Window Motor and Regulator - Front4 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
- Ground Strap BoltsClean contact surfaces12 lb-ft16 Nm
- Module Mounting Bolts6 lb-ft8 Nm
Window Motor and Regulator - Rear4 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
- Ground Strap BoltsClean contact surfaces12 lb-ft16 Nm
- Module Mounting Bolts6 lb-ft8 Nm
Wiper Linkage7 specs
- Battery Terminal Bolts6 lb-ft8 Nm
- Connector Screws3 lb-ft4 Nm
- Ground Strap BoltsEnsure clean contact9 lb-ft12 Nm
- Linkage Pivot Nuts9 lb-ft12 Nm
- Module Mounting Bolts6 lb-ft8 Nm
- Motor Mounting Bolts7 lb-ft10 Nm
- Sensor Mounting Bolts7 lb-ft10 Nm
Wiper Motor - Front4 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
- Ground Strap BoltsClean contact surfaces12 lb-ft16 Nm
- Module Mounting Bolts6 lb-ft8 Nm
Wiper Motor - Rear3 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
- Ground Strap BoltsClean contact surfaces12 lb-ft16 Nm
Wiper Switch3 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
- Ground Strap BoltsClean contact surfaces12 lb-ft16 Nm

Suspension

Ball Joint - Lower7 specs
- Control Arm BoltsTorque with vehicle weight on wheels122 lb-ft165 Nm
- Lower Ball Joint NutUse new cotter pin75 lb-ft102 Nm
- Pinch BoltNew bolt52 lb-ft70 Nm
- Strut Bolts63 lb-ft85 Nm
- Sway Bar Link52 lb-ft71 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug NutsTorque in star pattern112 lb-ft152 Nm
Ball Joint - Upper7 specs
- Control Arm BoltsTorque with vehicle weight on wheels122 lb-ft165 Nm
- Pinch BoltNew bolt52 lb-ft70 Nm
- Strut Bolts63 lb-ft85 Nm
- Sway Bar Link52 lb-ft71 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Upper Ball Joint NutUse new cotter pin75 lb-ft102 Nm
- Wheel Lug NutsTorque in star pattern112 lb-ft152 Nm
Ball Joints - Upper and Lower9 specs
- Control Arm BoltsTorque with vehicle weight on wheels122 lb-ft165 Nm
- Lower Ball Joint NutUse new cotter pin75 lb-ft102 Nm
- Pinch BoltNew bolt52 lb-ft70 Nm
- Strut Bolts63 lb-ft85 Nm
- Strut Tower Nuts37 lb-ft50 Nm
- Sway Bar Link52 lb-ft71 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Upper Ball Joint NutUse new cotter pin75.2 lb-ft102 Nm
- Wheel Lug NutsTorque in star pattern112 lb-ft152 Nm
Coil Spring - Front6 specs
- Control Arm BoltsTorque with vehicle weight on wheels85 lb-ft115 Nm
- Strut Bolts98 lb-ft133 Nm
- Strut Tower Nuts37 lb-ft50 Nm
- Sway Bar Link33 lb-ft45 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug NutsTorque in star pattern105 lb-ft142.4 Nm
Coil Spring - Rear6 specs
- Control Arm BoltsTorque with vehicle weight on wheels85 lb-ft115 Nm
- Strut Bolts98 lb-ft133 Nm
- Strut Tower Nuts37 lb-ft50 Nm
- Sway Bar Link33 lb-ft45 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug NutsTorque in star pattern105 lb-ft142.4 Nm
Coil Springs - Front Pair6 specs
- Control Arm BoltsTorque with vehicle weight on wheels85 lb-ft115 Nm
- Strut Bolts98 lb-ft133 Nm
- Strut Tower Nuts37 lb-ft50 Nm
- Sway Bar Link33 lb-ft45 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug NutsTorque in star pattern105 lb-ft142.4 Nm
Coil Springs - Rear Pair6 specs
- Control Arm BoltsTorque with vehicle weight on wheels85 lb-ft115 Nm
- Strut Bolts98 lb-ft133 Nm
- Strut Tower Nuts37 lb-ft50 Nm
- Sway Bar Link33 lb-ft45 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug NutsTorque in star pattern105 lb-ft142.4 Nm
Control Arm Bushing - Front Lower6 specs
- Control Arm BoltsTorque with vehicle weight on wheels85 lb-ft115 Nm
- Lower Ball Joint NutUse new cotter pin48 lb-ft65 Nm
- Strut Bolts98 lb-ft133 Nm
- Sway Bar Link33 lb-ft45 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug NutsTorque in star pattern105 lb-ft142.4 Nm
Control Arm Bushing - Front Upper6 specs
- Control Arm BoltsTorque with vehicle weight on wheels85 lb-ft115 Nm
- Strut Bolts98 lb-ft133 Nm
- Sway Bar Link33 lb-ft45 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Upper Ball Joint NutUse new cotter pin48 lb-ft65 Nm
- Wheel Lug NutsTorque in star pattern105 lb-ft142.4 Nm
Control Arm Bushing - Rear6 specs
- Ball Joint NutUse new cotter pin48 lb-ft65 Nm
- Control Arm BoltsTorque with vehicle weight on wheels85 lb-ft115 Nm
- Strut Bolts98 lb-ft133 Nm
- Sway Bar Link33 lb-ft45 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug NutsTorque in star pattern105 lb-ft142.4 Nm
Front Struts - Pair7 specs
- Control Arm BoltsTorque with vehicle weight on wheels122 lb-ft165 Nm
- Strut Bolts63 lb-ft85 Nm
- Strut to Knuckle Bolts63 lb-ft85 Nm
- Strut Tower Nuts37 lb-ft50 Nm
- Sway Bar Link35 lb-ft48 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug NutsTorque in star pattern115 lb-ft156 Nm
Front Suspension Rebuild5 specs
- Ball Joint Pinch BoltUse new bolt if locknut style37 lb-ft50 Nm
- Lower Control Arm BoltsTorque at ride height81 lb-ft110 Nm
- Strut Top Mount Nuts18 lb-ft25 Nm
- Sway Bar End Link Nuts44 lb-ft60 Nm
- Upper Control Arm BoltsTorque at ride height66 lb-ft90 Nm
Knuckle/Spindle - Front8 specs
- Control Arm BoltsTorque with vehicle weight on wheels66 lb-ft90 Nm
- Lower Ball Joint NutUse new cotter pin44 lb-ft60 Nm
- Strut Bolts98 lb-ft133 Nm
- Strut Tower Nuts37 lb-ft50 Nm
- Sway Bar Link33 lb-ft45 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Upper Ball Joint NutUse new cotter pin75.2 lb-ft102 Nm
- Wheel Lug NutsTorque in star pattern105 lb-ft142.4 Nm
Knuckle/Spindle - Rear7 specs
- Ball Joint NutUse new cotter pin75 lb-ft102 Nm
- Control Arm BoltsTorque with vehicle weight on wheels87 lb-ft118 Nm
- Strut Bolts98 lb-ft133 Nm
- Strut Tower Nuts37 lb-ft50 Nm
- Sway Bar Link44 lb-ft60 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug NutsTorque in star pattern115 lb-ft156 Nm
Lateral Arm5 specs
- Control Arm BoltsTorque with vehicle weight on wheels87 lb-ft118 Nm
- Strut Bolts98 lb-ft133 Nm
- Sway Bar Link44 lb-ft60 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug NutsTorque in star pattern115 lb-ft156 Nm
Lower Control Arm - Front6 specs
- Control Arm BoltsTorque with vehicle weight on wheels85 lb-ft115 Nm
- Lower Ball Joint NutUse new cotter pin75 lb-ft102 Nm
- Strut Bolts98 lb-ft133 Nm
- Sway Bar Link44 lb-ft60 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug NutsTorque in star pattern115 lb-ft156 Nm
Lower Control Arm - Rear6 specs
- Control Arm BoltsTorque with vehicle weight on wheels87 lb-ft118 Nm
- Lower Ball Joint NutUse new cotter pin75 lb-ft102 Nm
- Strut Bolts98 lb-ft133 Nm
- Sway Bar Link44 lb-ft60 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug NutsTorque in star pattern115 lb-ft156 Nm
Radius Arm5 specs
- Control Arm BoltsTorque with vehicle weight on wheels122 lb-ft165 Nm
- Strut Bolts98 lb-ft133 Nm
- Sway Bar Link52 lb-ft71 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug NutsTorque in star pattern115 lb-ft156 Nm
Radius Arm Bushing5 specs
- Control Arm BoltsTorque with vehicle weight on wheels122 lb-ft165 Nm
- Strut Bolts98 lb-ft133 Nm
- Sway Bar Link52 lb-ft71 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug NutsTorque in star pattern115 lb-ft156 Nm
Rear Shocks - Pair5 specs
- Strut Bolts63 lb-ft85 Nm
- Strut Tower Nuts44 lb-ft60 Nm
- Sway Bar Link33 lb-ft45 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug NutsTorque in star pattern115 lb-ft156 Nm
Rear Suspension Service4 specs
- Lower Control Arm BoltsTorque at ride height66 lb-ft90 Nm
- Shock Lower Bolt63 lb-ft85 Nm
- Sway Bar End Link Nuts37 lb-ft50 Nm
- Trailing Arm BoltsTorque at ride height88 lb-ft120 Nm
Shock Absorber Replacement2 specs
- Lower Mount Bolt66 lb-ft90 Nm
- Upper Mount NutUse new self-locking nut41 lb-ft55 Nm
Strut Assembly - Rear7 specs
- Control Arm BoltsTorque with vehicle weight on wheels122 lb-ft165 Nm
- Strut Bolts98 lb-ft133 Nm
- Strut to Knuckle Bolts104 lb-ft140 Nm
- Strut Tower Nuts37 lb-ft50 Nm
- Sway Bar Link52 lb-ft71 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug NutsTorque in star pattern115 lb-ft156 Nm
Strut Bearing6 specs
- Strut Bolts98 lb-ft133 Nm
- Strut to Knuckle Bolts104 lb-ft140 Nm
- Strut Tower Nuts37 lb-ft50 Nm
- Sway Bar Link52 lb-ft71 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug NutsTorque in star pattern105 lb-ft142.4 Nm
Strut Mount - Front6 specs
- Strut Bolts98 lb-ft133 Nm
- Strut to Knuckle Bolts104 lb-ft140 Nm
- Strut Tower Nuts37 lb-ft50 Nm
- Sway Bar Link52 lb-ft71 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug NutsTorque in star pattern115 lb-ft156 Nm
Strut Mount - Rear7 specs
- Control Arm BoltsTorque with vehicle weight on wheels83 lb-ft113 Nm
- Strut Bolts66 lb-ft90 Nm
- Strut to Knuckle Bolts104 lb-ft140 Nm
- Strut Tower Nuts37 lb-ft50 Nm
- Sway Bar Link52 lb-ft71 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug NutsTorque in star pattern115 lb-ft156 Nm
Subframe6 specs
- Control Arm BoltsTorque with vehicle weight on wheels83 lb-ft113 Nm
- Strut Bolts66 lb-ft90 Nm
- Strut Tower Nuts37 lb-ft50 Nm
- Sway Bar Link52 lb-ft71 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug NutsTorque in star pattern115 lb-ft156 Nm
Subframe Bushing6 specs
- Control Arm BoltsTorque with vehicle weight on wheels83 lb-ft113 Nm
- Strut Bolts66 lb-ft90 Nm
- Strut Tower Nuts37 lb-ft50 Nm
- Sway Bar Link52 lb-ft71 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug NutsTorque in star pattern115 lb-ft156 Nm
Sway Bar - Front7 specs
- Control Arm BoltsTorque with vehicle weight on wheels83 lb-ft113 Nm
- Strut Bolts66 lb-ft90 Nm
- Strut Tower Nuts37 lb-ft50 Nm
- Sway Bar Bracket Bolts40 lb-ft55 Nm
- Sway Bar Link52 lb-ft71 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug NutsTorque in star pattern115 lb-ft156 Nm
Sway Bar - Rear5 specs
- Strut Bolts98 lb-ft133 Nm
- Sway Bar Bracket Bolts40 lb-ft55 Nm
- Sway Bar Link33 lb-ft45 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug NutsTorque in star pattern115 lb-ft156 Nm
Sway Bar Bushing - Front7 specs
- Control Arm BoltsTorque with vehicle weight on wheels83 lb-ft113 Nm
- Strut Bolts66 lb-ft90 Nm
- Strut Tower Nuts37 lb-ft50 Nm
- Sway Bar Bracket Bolts40 lb-ft55 Nm
- Sway Bar Link52 lb-ft71 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug NutsTorque in star pattern115 lb-ft156 Nm
Sway Bar Bushing - Rear7 specs
- Control Arm BoltsTorque with vehicle weight on wheels83 lb-ft113 Nm
- Strut Bolts66 lb-ft90 Nm
- Strut Tower Nuts37 lb-ft50 Nm
- Sway Bar Bracket Bolts40 lb-ft55 Nm
- Sway Bar Link52 lb-ft71 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug NutsTorque in star pattern115 lb-ft156 Nm
Sway Bar Link - Front7 specs
- Control Arm BoltsTorque with vehicle weight on wheels83 lb-ft113 Nm
- Strut Bolts66 lb-ft90 Nm
- Strut Tower Nuts37 lb-ft50 Nm
- Sway Bar Bracket Bolts40 lb-ft55 Nm
- Sway Bar Link52 lb-ft71 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug NutsTorque in star pattern115 lb-ft156 Nm
Sway Bar Link - Rear7 specs
- Control Arm BoltsTorque with vehicle weight on wheels83 lb-ft113 Nm
- Strut Bolts66 lb-ft90 Nm
- Strut Tower Nuts37 lb-ft50 Nm
- Sway Bar Bracket Bolts40 lb-ft55 Nm
- Sway Bar Link52 lb-ft71 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug NutsTorque in star pattern115 lb-ft156 Nm
Sway Bar Links - Front Pair5 specs
- Strut Bolts98 lb-ft133 Nm
- Sway Bar Bracket Bolts40 lb-ft55 Nm
- Sway Bar Link33 lb-ft45 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug NutsTorque in star pattern115 lb-ft156 Nm
Torsion Bar6 specs
- Control Arm BoltsTorque with vehicle weight on wheels122 lb-ft165 Nm
- Strut Bolts98 lb-ft133 Nm
- Strut Tower Nuts37 lb-ft50 Nm
- Sway Bar Link52 lb-ft71 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug NutsTorque in star pattern105 lb-ft142.4 Nm
Torsion Bar Adjustment5 specs
- Control Arm BoltsTorque with vehicle weight on wheels122 lb-ft165 Nm
- Strut Bolts98 lb-ft133 Nm
- Strut Tower Nuts37 lb-ft50 Nm
- Sway Bar Link52 lb-ft71 Nm
- Wheel Lug NutsTorque in star pattern105 lb-ft142.4 Nm
Trailing Arm5 specs
- Control Arm BoltsTorque with vehicle weight on wheels122 lb-ft165 Nm
- Strut Bolts98 lb-ft133 Nm
- Sway Bar Link52 lb-ft71 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug NutsTorque in star pattern105 lb-ft142.4 Nm
Trailing Arm Bushing6 specs
- Control Arm BoltsTorque with vehicle weight on wheels122 lb-ft165 Nm
- Strut Bolts98 lb-ft133 Nm
- Strut Tower Nuts37 lb-ft50 Nm
- Sway Bar Link33 lb-ft45 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug NutsTorque in star pattern115 lb-ft156 Nm
Upper Control Arm - Front7 specs
- Control Arm BoltsTorque with vehicle weight on wheels63 lb-ft85 Nm
- Strut Bolts98 lb-ft133 Nm
- Strut Tower Nuts37 lb-ft50 Nm
- Sway Bar Link33 lb-ft45 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Upper Ball Joint NutUse new cotter pin75 lb-ft102 Nm
- Wheel Lug NutsTorque in star pattern115 lb-ft156 Nm
Upper Control Arm - Rear6 specs
- Control Arm BoltsTorque with vehicle weight on wheels63 lb-ft85 Nm
- Strut Bolts98 lb-ft133 Nm
- Strut Tower Nuts37 lb-ft50 Nm
- Sway Bar Link33 lb-ft45 Nm
- Upper Ball Joint NutUse new cotter pin75 lb-ft102 Nm
- Wheel Lug NutsTorque in star pattern115 lb-ft156 Nm

Steering

Power Steering Fluid Flush7 specs
- Coupling Bolt18 lb-ft25 Nm
- Power Steering Line FittingsUse new O-rings22 lb-ft30 Nm
- Steering Rack Bolts59 lb-ft80 Nm
- Tie Rod End Castle NutUse new cotter pin41 lb-ft55 Nm
- Tie Rod End NutUse new cotter pin35 lb-ft48 Nm
- Tie Rod Nut35 lb-ft48 Nm
- Wheel Lug Nuts115 lb-ft156 Nm
Power Steering Hose - High Pressure7 specs
- Coupling Bolt18 lb-ft25 Nm
- Power Steering Line FittingsUse new O-rings22 lb-ft30 Nm
- Steering Rack Bolts59 lb-ft80 Nm
- Tie Rod End Castle NutUse new cotter pin41 lb-ft55 Nm
- Tie Rod End NutUse new cotter pin46 lb-ft62 Nm
- Tie Rod Nut46 lb-ft62 Nm
- Wheel Lug Nuts112 lb-ft152 Nm
Power Steering Hose - Return7 specs
- Coupling Bolt18 lb-ft25 Nm
- Power Steering Line FittingsUse new O-rings18 lb-ft25 Nm
- Steering Rack Bolts59 lb-ft80 Nm
- Tie Rod End Castle NutUse new cotter pin41 lb-ft55 Nm
- Tie Rod End NutUse new cotter pin46 lb-ft62 Nm
- Tie Rod Nut46 lb-ft62 Nm
- Wheel Lug Nuts112 lb-ft152 Nm
Power Steering Pump8 specs
- High Pressure Hose FittingUse new O-rings18 lb-ft25 Nm
- Power Steering Pump Bolts18 lb-ft25 Nm
- Pressure Line FittingUse new O-rings22 lb-ft30 Nm
- Pulley NutHold pulley with pin spanner52 lb-ft70 Nm
- Pump Mounting Bolts18 lb-ft25 Nm
- Return Hose Clamp2 lb-ft3 Nm
- Return Line Clamp3 lb-ft4 Nm
- Serpentine Belt Tensioner41 lb-ft55 Nm
Power Steering Pump Pulley8 specs
- Coupling Bolt18 lb-ft25 Nm
- Pressure Line FittingNew O-ring29 lb-ft39 Nm
- Pump Mounting Bolts18 lb-ft25 Nm
- Steering Rack Bolts59 lb-ft80 Nm
- Tie Rod End Castle NutUse new cotter pin. Verify sequence with the service manual41 lb-ft55 Nm
- Tie Rod End NutUse new cotter pin35 lb-ft48 Nm
- Tie Rod Nut35 lb-ft48 Nm
- Wheel Lug Nuts115 lb-ft156 Nm
Power Steering Rack9 specs
- Coupling Bolt18 lb-ft25 Nm
- Power Steering Line FittingsUse new O-rings. Verify sequence with the service manual22 lb-ft30 Nm
- Pressure Line FittingNew O-ring29 lb-ft39 Nm
- Pump Mounting Bolts18 lb-ft25 Nm
- Steering Rack Bolts59 lb-ft80 Nm
- Tie Rod End Castle NutUse new cotter pin. Verify sequence with the service manual41 lb-ft55 Nm
- Tie Rod End NutUse new cotter pin35 lb-ft48 Nm
- Tie Rod Nut35 lb-ft48 Nm
- Wheel Lug Nuts115 lb-ft156 Nm
Power Steering Reservoir7 specs
- Coupling Bolt18 lb-ft25 Nm
- Power Steering Line FittingsUse new O-rings18 lb-ft25 Nm
- Steering Rack Bolts59 lb-ft80 Nm
- Tie Rod End Castle NutUse new cotter pin41 lb-ft55 Nm
- Tie Rod End NutUse new cotter pin46 lb-ft62 Nm
- Tie Rod Nut46 lb-ft62 Nm
- Wheel Lug Nuts112 lb-ft152 Nm
Rack and Pinion Boots7 specs
- Coupling Bolt18 lb-ft25 Nm
- Power Steering Line FittingsUse new O-rings22 lb-ft30 Nm
- Steering Rack Bolts59 lb-ft80 Nm
- Tie Rod End Castle NutUse new cotter pin41 lb-ft55 Nm
- Tie Rod End NutUse new cotter pin46 lb-ft62 Nm
- Tie Rod Nut46 lb-ft62 Nm
- Wheel Lug Nuts112 lb-ft152 Nm
Steering Angle Sensor5 specs
- Coupling Bolt18 lb-ft25 Nm
- Tie Rod End Castle NutUse new cotter pin. Verify sequence with the service manual41 lb-ft55 Nm
- Tie Rod End NutUse new cotter pin35 lb-ft48 Nm
- Tie Rod Nut35 lb-ft48 Nm
- Wheel Lug Nuts105 lb-ft142.4 Nm
Steering Column9 specs
- Coupling Bolt18 lb-ft25 Nm
- Ignition Switch BoltsVerify sequence with the service manual4 lb-ft5 Nm
- Pinch BoltVerify sequence with the service manual18 lb-ft25 Nm
- Power Steering Line FittingsUse new O-rings29 lb-ft39 Nm
- Steering Column BoltsVerify sequence with the service manual18 lb-ft25 Nm
- Steering Rack Bolts86 lb-ft117 Nm
- Tie Rod End NutUse new cotter pin35 lb-ft48 Nm
- Tie Rod Nut35 lb-ft48 Nm
- Wheel Lug Nuts105 lb-ft142.4 Nm
Steering Coupler6 specs
- Coupling Bolt18 lb-ft25 Nm
- Steering Rack BoltsVerify sequence with the service manual74 lb-ft100 Nm
- Tie Rod End Castle NutUse new cotter pin. Verify sequence with the service manual41 lb-ft55 Nm
- Tie Rod End NutUse new cotter pin46 lb-ft62 Nm
- Tie Rod Nut46 lb-ft62 Nm
- Wheel Lug Nuts115 lb-ft156 Nm
Steering Damper5 specs
- Coupling Bolt29 lb-ft39 Nm
- Tie Rod End Castle NutUse new cotter pin. Verify sequence with the service manual41 lb-ft55 Nm
- Tie Rod End NutUse new cotter pin46 lb-ft62 Nm
- Tie Rod Nut46 lb-ft62 Nm
- Wheel Lug Nuts105 lb-ft142.4 Nm
Steering Shaft - Intermediate7 specs
- Coupling Bolt18 lb-ft25 Nm
- Power Steering Line FittingsUse new O-rings. Verify sequence with the service manual22 lb-ft30 Nm
- Steering Rack BoltsVerify sequence with the service manual59 lb-ft80 Nm
- Tie Rod End Castle NutUse new cotter pin. Verify sequence with the service manual41 lb-ft55 Nm
- Tie Rod End NutUse new cotter pin46 lb-ft62 Nm
- Tie Rod Nut46 lb-ft62 Nm
- Wheel Lug Nuts115 lb-ft156 Nm
Steering Shaft - Upper7 specs
- Coupling Bolt18 lb-ft25 Nm
- Power Steering Line FittingsUse new O-rings. Verify sequence with the service manual22 lb-ft30 Nm
- Steering Rack Bolts59 lb-ft80 Nm
- Tie Rod End Castle NutUse new cotter pin. Verify sequence with the service manual41 lb-ft55 Nm
- Tie Rod End NutUse new cotter pin46 lb-ft62 Nm
- Tie Rod Nut46 lb-ft62 Nm
- Wheel Lug Nuts115 lb-ft156 Nm
Steering Wheel8 specs
- Airbag Module BoltsTorx - usually T30. Verify sequence with the service manual5 lb-ft7 Nm
- Coupling Bolt18 lb-ft25 Nm
- Power Steering Line FittingsUse new O-rings22 lb-ft30 Nm
- Steering Rack Bolts59 lb-ft80 Nm
- Steering Wheel NutVerify sequence with the service manual40 lb-ft54 Nm
- Tie Rod End NutUse new cotter pin46 lb-ft62 Nm
- Tie Rod Nut46 lb-ft62 Nm
- Wheel Lug Nuts115 lb-ft156 Nm
Tie Rod Assembly7 specs
- Coupling Bolt18 lb-ft25 Nm
- Steering Rack Bolts59 lb-ft80 Nm
- Tie Rod End Castle NutUse new cotter pin41 lb-ft55 Nm
- Tie Rod End NutUse new cotter pin46 lb-ft62 Nm
- Tie Rod Lock NutAfter alignment35 lb-ft48 Nm
- Tie Rod Nut46 lb-ft62 Nm
- Wheel Lug Nuts115 lb-ft156 Nm
Tie Rod End - Inner7 specs
- Coupling Bolt18 lb-ft25 Nm
- Steering Rack Bolts59 lb-ft80 Nm
- Tie Rod End Castle NutUse new cotter pin41 lb-ft55 Nm
- Tie Rod End NutUse new cotter pin46 lb-ft62 Nm
- Tie Rod Lock NutAfter alignment35 lb-ft48 Nm
- Tie Rod Nut55 lb-ft75 Nm
- Wheel Lug Nuts115 lb-ft156 Nm
Tie Rod End - Outer7 specs
- Coupling Bolt18 lb-ft25 Nm
- Steering Rack Bolts59 lb-ft80 Nm
- Tie Rod End Castle NutUse new cotter pin41 lb-ft55 Nm
- Tie Rod End NutUse new cotter pin46 lb-ft62 Nm
- Tie Rod Lock NutAfter alignment35 lb-ft48 Nm
- Tie Rod Nut46 lb-ft62 Nm
- Wheel Lug Nuts115 lb-ft156 Nm
Tie Rods - Both Sides7 specs
- Coupling Bolt18 lb-ft25 Nm
- Steering Rack Bolts59 lb-ft80 Nm
- Tie Rod End Castle NutUse new cotter pin41 lb-ft55 Nm
- Tie Rod End NutUse new cotter pin46 lb-ft62 Nm
- Tie Rod Lock NutAfter alignment35 lb-ft48 Nm
- Tie Rod Nut46 lb-ft62 Nm
- Wheel Lug Nuts115 lb-ft156 Nm

Drivetrain

Axle Seal - Rear7 specs
- Axle NutUse new cotter pin or stake nut277 lb-ft375 Nm
- CV Bolts52 lb-ft70 Nm
- CV Joint Bolts52 lb-ft71 Nm
- Differential Cover Bolts26 lb-ft35 Nm
- Driveshaft Bolts46 lb-ft63 Nm
- Driveshaft U-Joint StrapsTighten evenly15 lb-ft20 Nm
- Wheel Lug NutsTorque in star pattern112 lb-ft152 Nm
CV Axle - Rear8 specs
- Axle NutUse new nut, stake after207 lb-ft281 Nm
- Ball Joint Nut86 lb-ft117 Nm
- CV Axle Nut240 lb-ft325 Nm
- CV Bolts52 lb-ft70 Nm
- CV Joint Bolts52 lb-ft71 Nm
- Differential Cover BoltsApply RTV sealant29 lb-ft39 Nm
- Driveshaft Bolts63 lb-ft85 Nm
- Wheel Lug Nuts115 lb-ft156 Nm
CV Axles - Front Pair1 spec
- Wheel Lug Nuts105 lb-ft142.4 Nm
CV Boot - Inner6 specs
- Axle NutUse new cotter pin or stake nut240 lb-ft325 Nm
- CV Bolts52 lb-ft70 Nm
- CV Joint Bolts52 lb-ft71 Nm
- Driveshaft Bolts48 lb-ft65 Nm
- Driveshaft U-Joint StrapsTighten evenly15 lb-ft20 Nm
- Wheel Lug NutsTorque in star pattern112 lb-ft152 Nm
CV Boot - Outer6 specs
- Axle NutUse new cotter pin or stake nut240 lb-ft325 Nm
- CV Bolts52 lb-ft70 Nm
- CV Joint Bolts52 lb-ft71 Nm
- Driveshaft Bolts48 lb-ft65 Nm
- Driveshaft U-Joint StrapsTighten evenly15 lb-ft20 Nm
- Wheel Lug NutsTorque in star pattern112 lb-ft152 Nm
Differential Cover Gasket7 specs
- Axle NutUse new cotter pin or stake nut240 lb-ft325 Nm
- CV Bolts52 lb-ft70 Nm
- CV Joint Bolts52 lb-ft71 Nm
- Differential Cover Bolts26 lb-ft35 Nm
- Driveshaft Bolts48 lb-ft65 Nm
- Driveshaft U-Joint StrapsTighten evenly15 lb-ft20 Nm
- Wheel Lug NutsTorque in star pattern112 lb-ft152 Nm
Differential Fluid Change - Rear6 specs
- Axle NutUse new cotter pin or stake nut240 lb-ft325 Nm
- CV Bolts52 lb-ft70 Nm
- CV Joint Bolts52 lb-ft71 Nm
- Differential Cover Bolts26 lb-ft35 Nm
- Driveshaft Bolts63 lb-ft85 Nm
- Driveshaft U-Joint StrapsTighten evenly15 lb-ft20 Nm
Differential Pinion Seal5 specs
- CV Bolts52 lb-ft70 Nm
- CV Joint Bolts52 lb-ft71 Nm
- Differential Cover Bolts26 lb-ft35 Nm
- Driveshaft Bolts63 lb-ft85 Nm
- Driveshaft U-Joint StrapsTighten evenly15 lb-ft20 Nm
Differential Rebuild - Rear9 specs
- Axle NutUse new cotter pin or stake nut240 lb-ft325 Nm
- CV Bolts52 lb-ft70 Nm
- CV Joint Bolts52 lb-ft71 Nm
- Differential Cover Bolts26 lb-ft35 Nm
- Drain PlugNew washer35 lb-ft47 Nm
- Driveshaft Bolts48 lb-ft65 Nm
- Driveshaft U-Joint StrapsTighten evenly15 lb-ft20 Nm
- Fill Plug35 lb-ft47 Nm
- Wheel Lug NutsTorque in star pattern112 lb-ft152 Nm
Driveshaft - Rear3 specs
- Differential Pinion Yoke NutUse new nut, set pinion preload184 lb-ft250 Nm
- Driveshaft Flange Bolts55 lb-ft75 Nm
- U-Joint Strap BoltsApply threadlocker26 lb-ft35 Nm
Driveshaft Center Support Bearing2 specs
- Center Support Bearing Bracket Bolts37 lb-ft50 Nm
- Driveshaft Flange Bolts55 lb-ft75 Nm
Limited Slip Clutch Pack7 specs
- Axle NutUse new cotter pin or stake nut221 lb-ft300 Nm
- CV Bolts52 lb-ft70 Nm
- CV Joint Bolts44 lb-ft60 Nm
- Differential Cover Bolts26 lb-ft35 Nm
- Driveshaft Bolts63 lb-ft85 Nm
- Driveshaft U-Joint StrapsTighten evenly15 lb-ft20 Nm
- Wheel Lug NutsTorque in star pattern112 lb-ft152 Nm
Ring and Pinion7 specs
- Axle NutUse new cotter pin or stake nut221 lb-ft300 Nm
- CV Bolts52 lb-ft70 Nm
- CV Joint Bolts52 lb-ft71 Nm
- Differential Cover Bolts26 lb-ft35 Nm
- Driveshaft Bolts63 lb-ft85 Nm
- Driveshaft U-Joint StrapsTighten evenly15 lb-ft20 Nm
- Wheel Lug NutsTorque in star pattern112 lb-ft152 Nm
U-Joint8 specs
- Axle NutUse new nut, stake after207 lb-ft281 Nm
- CV Bolts52 lb-ft70 Nm
- CV Joint Bolts52 lb-ft71 Nm
- Differential Cover BoltsApply RTV sealant29 lb-ft39 Nm
- Driveshaft Bolts44 lb-ft60 Nm
- Driveshaft U-Joint StrapsTighten evenly15 lb-ft20 Nm
- Wheel Lug Nuts115 lb-ft156 Nm
- Yoke NutIf equipped111 lb-ft150 Nm
Wheel Bearing - Press-In Front7 specs
- ABS Sensor Bolt9 lb-ft12 Nm
- Axle NutUse new cotter pin or stake nut184 lb-ft250 Nm
- CV Joint Bolts52 lb-ft71 Nm
- Driveshaft Bolts63 lb-ft85 Nm
- Driveshaft U-Joint StrapsTighten evenly15 lb-ft20 Nm
- Hub Bolts86 lb-ft117 Nm
- Wheel Lug NutsTorque in star pattern112 lb-ft152 Nm
Wheel Bearing - Press-In Rear8 specs
- ABS Sensor Bolt9 lb-ft12 Nm
- Axle NutUse new cotter pin or stake nut184 lb-ft250 Nm
- CV Joint Bolts44 lb-ft60 Nm
- Differential Cover Bolts26 lb-ft35 Nm
- Driveshaft Bolts44 lb-ft60 Nm
- Driveshaft U-Joint StrapsTighten evenly15 lb-ft20 Nm
- Hub Bolts86 lb-ft117 Nm
- Wheel Lug NutsTorque in star pattern112 lb-ft152 Nm
Wheel Bearing Hub - Front4 specs
- ABS Sensor BoltDo not overtighten7 lb-ft10 Nm
- Axle NutUse new cotter pin after torque184 lb-ft250 Nm
- Caliper Bracket Bolts88 lb-ft120 Nm
- Wheel Bearing Hub BoltsApply threadlocker if specified81 lb-ft110 Nm
Wheel Bearing Hub - Rear3 specs
- Axle NutUse new cotter pin after torque258 lb-ft350 Nm
- Caliper Bracket Bolts81 lb-ft110 Nm
- Wheel Bearing Hub BoltsApply threadlocker if specified74 lb-ft100 Nm
Wheel Studs6 specs
- Axle NutUse new cotter pin or stake nut258 lb-ft350 Nm
- CV Bolts52 lb-ft70 Nm
- CV Joint Bolts52 lb-ft71 Nm
- Driveshaft Bolts52 lb-ft70 Nm
- Driveshaft U-Joint StrapsTighten evenly15 lb-ft20 Nm
- Wheel Lug NutsTorque in star pattern112 lb-ft152 Nm

Transmission

Neutral Safety Switch3 specs
- Drain PlugUse new washer29 lb-ft39 Nm
- Fill Plug29 lb-ft39 Nm
- Switch Mounting Bolts11 lb-ft15 Nm
Overdrive Solenoid5 specs
- Drain PlugUse new washer29 lb-ft39 Nm
- Fill Plug29 lb-ft39 Nm
- Flywheel BoltsOften TTY, tighten in star pattern70 lb-ft95 Nm
- Transmission Drain PlugUse new crush washer if equipped22 lb-ft30 Nm
- Transmission Pan BoltsTighten in criss-cross pattern9 lb-ft12 Nm
Pressure Plate4 specs
- Drain PlugUse new washer29 lb-ft39 Nm
- Fill Plug24 lb-ft33 Nm
- Flywheel BoltsOften TTY, tighten in star pattern35 lb-ft48 Nm
- Transmission Drain PlugUse new crush washer if equipped22 lb-ft30 Nm
Shift Cable4 specs
- Adjustment Nut7 lb-ft10 Nm
- Cable Bracket Bolts11 lb-ft15 Nm
- Drain PlugUse new washer29 lb-ft39 Nm
- Fill Plug29 lb-ft39 Nm
Shift Fork3 specs
- Drain PlugUse new washer24 lb-ft33 Nm
- Fill Plug24 lb-ft33 Nm
- Transmission Drain PlugUse new crush washer if equipped22 lb-ft30 Nm
Shift Linkage4 specs
- Drain PlugUse new washer29 lb-ft39 Nm
- Fill Plug29 lb-ft39 Nm
- Linkage Bolts11 lb-ft15 Nm
- Pivot Bolts9 lb-ft12 Nm
Shift Solenoid - Single4 specs
- Drain PlugUse new washer24 lb-ft33 Nm
- Fill Plug24 lb-ft33 Nm
- Transmission Drain PlugUse new crush washer if equipped22 lb-ft30 Nm
- Transmission Pan BoltsTighten in criss-cross pattern9 lb-ft12 Nm
Shift Solenoids - All4 specs
- Drain PlugUse new washer24 lb-ft33 Nm
- Fill Plug24 lb-ft33 Nm
- Transmission Drain PlugUse new crush washer if equipped22 lb-ft30 Nm
- Transmission Pan BoltsTighten in criss-cross pattern9 lb-ft12 Nm
Synchros - All4 specs
- Drain PlugUse new washer29 lb-ft39 Nm
- Fill Plug29 lb-ft39 Nm
- Transmission Drain PlugUse new crush washer if equipped22 lb-ft30 Nm
- Transmission Pan BoltsTighten in criss-cross pattern9 lb-ft12 Nm
Synchros - Single Gear3 specs
- Drain PlugUse new washer29 lb-ft39 Nm
- Fill Plug29 lb-ft39 Nm
- Transmission Drain PlugUse new crush washer if equipped22 lb-ft30 Nm
Torque Converter4 specs
- Drain PlugUse new washer29 lb-ft39 Nm
- Fill Plug29 lb-ft39 Nm
- Flexplate BoltsAutomatic transmissions63 lb-ft85 Nm
- Torque Converter BoltsTighten evenly37 lb-ft50 Nm
Torque Converter Clutch Solenoid5 specs
- Drain PlugUse new washer29 lb-ft39 Nm
- Fill Plug29 lb-ft39 Nm
- Flywheel BoltsOften TTY, tighten in star pattern70 lb-ft95 Nm
- Transmission Drain PlugUse new crush washer if equipped22 lb-ft30 Nm
- Transmission Pan BoltsTighten in criss-cross pattern9 lb-ft12 Nm
Transmission Control Module4 specs
- Drain PlugUse new washer29 lb-ft39 Nm
- Fill Plug29 lb-ft39 Nm
- Transmission Drain PlugUse new crush washer if equipped22 lb-ft30 Nm
- Transmission Pan BoltsTighten in criss-cross pattern9 lb-ft12 Nm
Transmission Cooler Lines2 specs
- Drain PlugUse new washer29 lb-ft39 Nm
- Fill Plug29 lb-ft39 Nm
Transmission Filter4 specs
- Drain PlugUse new washer29 lb-ft39 Nm
- Fill Plug29 lb-ft39 Nm
- Transmission Drain PlugUse new crush washer if equipped22 lb-ft30 Nm
- Transmission Pan BoltsTighten in criss-cross pattern9 lb-ft12 Nm
Transmission Filter and Fluid4 specs
- Drain PlugUse new washer29 lb-ft39 Nm
- Fill Plug29 lb-ft39 Nm
- Transmission Drain PlugUse new crush washer if equipped22 lb-ft30 Nm
- Transmission Pan BoltsTighten in criss-cross pattern9 lb-ft12 Nm
Transmission Fluid Change5 specs
- Drain PlugUse new washer29 lb-ft39 Nm
- Fill Plug29 lb-ft39 Nm
- Transmission Drain PlugUse new crush washer if equipped22 lb-ft30 Nm
- Transmission Filter BoltsIf equipped with bolted filter6 lb-ft8 Nm
- Transmission Pan BoltsTighten in criss-cross pattern9 lb-ft12 Nm
Transmission Flush4 specs
- Drain PlugUse new washer29 lb-ft39 Nm
- Fill Plug29 lb-ft39 Nm
- Transmission Drain PlugUse new crush washer if equipped22 lb-ft30 Nm
- Transmission Pan BoltsTighten in criss-cross pattern9 lb-ft12 Nm
Transmission Input Shaft Bearing5 specs
- Drain PlugUse new washer29 lb-ft39 Nm
- Fill Plug29 lb-ft39 Nm
- Flywheel BoltsOften TTY, tighten in star pattern70 lb-ft95 Nm
- Transmission Drain PlugUse new crush washer if equipped22 lb-ft30 Nm
- Transmission Pan BoltsTighten in criss-cross pattern9 lb-ft12 Nm
Transmission Oil Cooler9 specs
- Coolant Drain Plug11 lb-ft15 Nm
- Drain PetcockHand tight6 lb-ft8 Nm
- Drain PlugUse new washer29 lb-ft39 Nm
- Fan Bolts9 lb-ft12 Nm
- Fill Plug29 lb-ft39 Nm
- Hose Clamps2 lb-ft3 Nm
- Pump BoltsTorque in sequence21 lb-ft28 Nm
- Thermostat Housing Bolt11 lb-ft15 Nm
- Water Pump BoltsTighten in criss-cross pattern18 lb-ft25 Nm
Transmission Output Shaft Bearing5 specs
- Drain PlugUse new washer29 lb-ft39 Nm
- Fill Plug29 lb-ft39 Nm
- Flywheel BoltsOften TTY, tighten in star pattern70 lb-ft95 Nm
- Transmission Drain PlugUse new crush washer if equipped22 lb-ft30 Nm
- Transmission Pan BoltsTighten in criss-cross pattern9 lb-ft12 Nm
Transmission Pan Gasket4 specs
- Drain PlugUse new washer24 lb-ft33 Nm
- Fill Plug24 lb-ft33 Nm
- Transmission Drain PlugUse new crush washer if equipped22 lb-ft30 Nm
- Transmission Pan BoltsTighten in criss-cross pattern9 lb-ft12 Nm
Transmission R&R - Automatic5 specs
- Drain PlugUse new washer24 lb-ft33 Nm
- Fill Plug24 lb-ft33 Nm
- Flywheel BoltsOften TTY, tighten in star pattern70 lb-ft95 Nm
- Transmission Drain PlugUse new crush washer if equipped22 lb-ft30 Nm
- Transmission Pan BoltsTighten in criss-cross pattern9 lb-ft12 Nm
Transmission Range Sensor4 specs
- Drain PlugUse new washer24 lb-ft33 Nm
- Fill Plug24 lb-ft33 Nm
- Transmission Drain PlugUse new crush washer if equipped22 lb-ft30 Nm
- Transmission Pan BoltsTighten in criss-cross pattern9 lb-ft12 Nm
Transmission Rebuild - Automatic5 specs
- Drain PlugUse new washer24 lb-ft33 Nm
- Fill Plug24 lb-ft33 Nm
- Flywheel BoltsOften TTY, tighten in star pattern70 lb-ft95 Nm
- Transmission Drain PlugUse new crush washer if equipped22 lb-ft30 Nm
- Transmission Pan BoltsTighten in criss-cross pattern9 lb-ft12 Nm
Transmission Speed Sensor - Input4 specs
- Drain PlugUse new washer24 lb-ft33 Nm
- Fill Plug24 lb-ft33 Nm
- Transmission Drain PlugUse new crush washer if equipped22 lb-ft30 Nm
- Transmission Pan BoltsTighten in criss-cross pattern9 lb-ft12 Nm
Transmission Speed Sensor - Output3 specs
- Drain PlugUse new washer24 lb-ft33 Nm
- Fill Plug24 lb-ft33 Nm
- Transmission Drain PlugUse new crush washer if equipped22 lb-ft30 Nm
Valve Body5 specs
- Drain PlugUse new washer29 lb-ft39 Nm
- Fill Plug29 lb-ft39 Nm
- Flywheel BoltsOften TTY, tighten in star pattern35 lb-ft48 Nm
- Transmission Drain PlugUse new crush washer if equipped22 lb-ft30 Nm
- Transmission Pan BoltsTighten in criss-cross pattern9 lb-ft12 Nm

Exhaust

Catalytic Converter - Direct Fit5 specs
- Exhaust Flange BoltApply anti-seize18 lb-ft25 Nm
- Hanger Bolts17 lb-ft23 Nm
- Heat Shield Bolts7 lb-ft10 Nm
- Manifold NutsApply anti-seize29 lb-ft39 Nm
- O2 SensorApply anti-seize to threads only33 lb-ft45 Nm
Catalytic Converter - Universal5 specs
- Exhaust Flange BoltApply anti-seize18 lb-ft25 Nm
- Hanger Bolts17 lb-ft23 Nm
- Heat Shield Bolts7 lb-ft10 Nm
- Manifold NutsApply anti-seize29 lb-ft39 Nm
- O2 SensorApply anti-seize to threads only33 lb-ft45 Nm
Downpipe5 specs
- Exhaust Flange BoltApply anti-seize18 lb-ft25 Nm
- Hanger Bolts17 lb-ft23 Nm
- Heat Shield Bolts7 lb-ft10 Nm
- Manifold NutsApply anti-seize18 lb-ft25 Nm
- O2 SensorApply anti-seize to threads only33 lb-ft45 Nm
EGR Tube4 specs
- Exhaust Flange BoltApply anti-seize33 lb-ft45 Nm
- Hanger Bolts17 lb-ft23 Nm
- Heat Shield Bolts7 lb-ft10 Nm
- Manifold NutsApply anti-seize29 lb-ft39 Nm
EGR Valve6 specs
- EGR Tube Fitting26 lb-ft35 Nm
- EGR Valve Bolts18 lb-ft25 Nm
- Hanger Bolts17 lb-ft23 Nm
- Heat Shield Bolts12 lb-ft16 Nm
- Manifold NutsApply anti-seize29 lb-ft39 Nm
- O2 SensorApply anti-seize to threads40 lb-ft54 Nm
Exhaust Clamp5 specs
- Exhaust Flange BoltApply anti-seize18 lb-ft25 Nm
- Hanger Bolts17 lb-ft23 Nm
- Heat Shield Bolts7 lb-ft10 Nm
- Manifold NutsApply anti-seize18 lb-ft25 Nm
- O2 SensorApply anti-seize to threads only33 lb-ft45 Nm
Exhaust Gasket - Front5 specs
- Exhaust Flange BoltApply anti-seize18 lb-ft25 Nm
- Hanger Bolts17 lb-ft23 Nm
- Heat Shield Bolts7 lb-ft10 Nm
- Manifold NutsApply anti-seize18 lb-ft25 Nm
- O2 SensorApply anti-seize to threads only33 lb-ft45 Nm
Exhaust Gasket - Rear5 specs
- Exhaust Flange BoltApply anti-seize18 lb-ft25 Nm
- Hanger Bolts17 lb-ft23 Nm
- Heat Shield Bolts7 lb-ft10 Nm
- Manifold NutsApply anti-seize18 lb-ft25 Nm
- O2 SensorApply anti-seize to threads only33 lb-ft45 Nm
Exhaust Hangers5 specs
- Exhaust Flange BoltApply anti-seize18 lb-ft25 Nm
- Hanger Bolts17 lb-ft23 Nm
- Heat Shield Bolts7 lb-ft10 Nm
- Manifold NutsApply anti-seize18 lb-ft25 Nm
- O2 SensorApply anti-seize to threads only33 lb-ft45 Nm
Exhaust Manifold Studs5 specs
- Exhaust Flange BoltApply anti-seize18 lb-ft25 Nm
- Hanger Bolts17 lb-ft23 Nm
- Heat Shield Bolts7 lb-ft10 Nm
- Manifold NutsApply anti-seize18 lb-ft25 Nm
- O2 SensorApply anti-seize to threads only33 lb-ft45 Nm
Exhaust Pipe - Rear Section5 specs
- Exhaust Flange BoltApply anti-seize18 lb-ft25 Nm
- Hanger Bolts17 lb-ft23 Nm
- Heat Shield Bolts7 lb-ft10 Nm
- Manifold NutsApply anti-seize18 lb-ft25 Nm
- O2 SensorApply anti-seize to threads only33 lb-ft45 Nm
Exhaust Tip4 specs
- Exhaust Flange BoltApply anti-seize33 lb-ft45 Nm
- Hanger Bolts17 lb-ft23 Nm
- Manifold NutsApply anti-seize18 lb-ft25 Nm
- O2 SensorApply anti-seize to threads only33 lb-ft45 Nm
Flex Pipe5 specs
- Exhaust Clamps41 lb-ft55 Nm
- Hanger Bolts17 lb-ft23 Nm
- Heat Shield Bolts12 lb-ft16 Nm
- Manifold NutsApply anti-seize18 lb-ft25 Nm
- O2 SensorApply anti-seize to threads33 lb-ft45 Nm
Front Pipe5 specs
- Exhaust Flange BoltApply anti-seize18 lb-ft25 Nm
- Hanger Bolts17 lb-ft23 Nm
- Heat Shield Bolts7 lb-ft10 Nm
- Manifold NutsApply anti-seize18 lb-ft25 Nm
- O2 SensorApply anti-seize to threads only33 lb-ft45 Nm
Intermediate Pipe5 specs
- Exhaust Flange BoltApply anti-seize18 lb-ft25 Nm
- Hanger Bolts17 lb-ft23 Nm
- Heat Shield Bolts7 lb-ft10 Nm
- Manifold NutsApply anti-seize18 lb-ft25 Nm
- O2 SensorApply anti-seize to threads only33 lb-ft45 Nm
Muffler2 specs
- Hanger Bracket Bolts18 lb-ft25 Nm
- Muffler Clamps41 lb-ft55 Nm
O2 Sensor - Downstream5 specs
- Exhaust Flange BoltApply anti-seize18 lb-ft25 Nm
- Hanger Bolts17 lb-ft23 Nm
- Heat Shield Bolts7 lb-ft10 Nm
- Manifold NutsApply anti-seize29 lb-ft39 Nm
- O2 SensorApply anti-seize to threads only33 lb-ft45 Nm
O2 Sensor - Upstream5 specs
- Exhaust Flange BoltApply anti-seize18 lb-ft25 Nm
- Hanger Bolts17 lb-ft23 Nm
- Heat Shield Bolts7 lb-ft10 Nm
- Manifold NutsApply anti-seize29 lb-ft39 Nm
- O2 SensorApply anti-seize to threads only33 lb-ft45 Nm
O2 Sensors - All5 specs
- Exhaust Flange BoltApply anti-seize18 lb-ft25 Nm
- Hanger Bolts17 lb-ft23 Nm
- Heat Shield Bolts7 lb-ft10 Nm
- Manifold NutsApply anti-seize29 lb-ft39 Nm
- O2 SensorApply anti-seize to threads only33 lb-ft45 Nm
Resonator5 specs
- Exhaust Clamps41 lb-ft55 Nm
- Hanger Bolts17 lb-ft23 Nm
- Heat Shield Bolts12 lb-ft16 Nm
- Manifold NutsApply anti-seize18 lb-ft25 Nm
- O2 SensorApply anti-seize to threads33 lb-ft45 Nm
Tail Pipe5 specs
- Exhaust Flange BoltApply anti-seize18 lb-ft25 Nm
- Hanger Bolts17 lb-ft23 Nm
- Heat Shield Bolts7 lb-ft10 Nm
- Manifold NutsApply anti-seize22 lb-ft30 Nm
- O2 SensorApply anti-seize to threads only33 lb-ft45 Nm

Heating and A/C

AC Accumulator5 specs
- AC Line FittingsUse new O-rings, add PAG oil15 lb-ft20 Nm
- Blower Motor Mounting Screw3 lb-ft4 Nm
- Compressor Bolts29 lb-ft39 Nm
- Duct Clips2 lb-ft3 Nm
- Mounting Bracket Bolts21 lb-ft28 Nm
AC Clutch Coil4 specs
- Blower Motor Mounting Screw3 lb-ft4 Nm
- Compressor Bolts29 lb-ft39 Nm
- Duct Clips2 lb-ft3 Nm
- Mounting Bracket Bolts21 lb-ft28 Nm
AC Compressor3 specs
- AC Compressor Bolts18 lb-ft25 Nm
- AC Line FittingsUse new O-rings, add PAG oil15 lb-ft20 Nm
- Clutch Connector Bolt6 lb-ft8 Nm
AC Compressor Clutch4 specs
- Blower Motor Mounting Screw3 lb-ft4 Nm
- Compressor Bolts29 lb-ft39 Nm
- Duct Clips2 lb-ft3 Nm
- Mounting Bracket Bolts21 lb-ft28 Nm
AC Compressor Oil Add5 specs
- AC Line FittingsUse new O-rings, add PAG oil15 lb-ft20 Nm
- Blower Motor Mounting Screw3 lb-ft4 Nm
- Compressor Bolts18 lb-ft25 Nm
- Duct Clips2 lb-ft3 Nm
- Mounting Bracket Bolts21 lb-ft28 Nm
AC Condenser2 specs
- AC Line FittingsUse new O-rings15 lb-ft20 Nm
- Condenser Mounting Bolts9 lb-ft12 Nm
AC Evaporator7 specs
- AC Line FittingsUse new O-rings, add PAG oil15 lb-ft20 Nm
- Blower Motor Mounting Screw6 lb-ft8 Nm
- Compressor Bolts18 lb-ft25 Nm
- Duct Clips2 lb-ft3 Nm
- Evaporator Case Screws4 lb-ft5 Nm
- Expansion Valve7 lb-ft10 Nm
- Mounting Bracket Bolts21 lb-ft28 Nm
AC Expansion Valve (TXV)6 specs
- AC Line FittingsUse new O-rings, add PAG oil15 lb-ft20 Nm
- Blower Motor Mounting Screw6 lb-ft8 Nm
- Compressor Bolts18 lb-ft25 Nm
- Duct Clips2 lb-ft3 Nm
- Expansion Valve7 lb-ft10 Nm
- Mounting Bracket Bolts21 lb-ft28 Nm
AC High Pressure Switch5 specs
- AC Line FittingsUse new O-rings, add PAG oil15 lb-ft20 Nm
- Blower Motor Mounting Screw3 lb-ft4 Nm
- Compressor Bolts18 lb-ft25 Nm
- Duct Clips2 lb-ft3 Nm
- Mounting Bracket Bolts21 lb-ft28 Nm
AC Hose - High Side5 specs
- AC Line FittingsUse new O-rings, add PAG oil15 lb-ft20 Nm
- Blower Motor Mounting Screw3 lb-ft4 Nm
- Compressor Bolts18 lb-ft25 Nm
- Duct Clips2 lb-ft3 Nm
- Mounting Bracket Bolts21 lb-ft28 Nm
AC Hose - Low Side6 specs
- AC Line FittingsUse new O-rings, add PAG oil15 lb-ft20 Nm
- Blower Motor Mounting Screw3 lb-ft4 Nm
- Compressor Bolts18 lb-ft25 Nm
- Duct Clips2 lb-ft3 Nm
- Hose Clamps2 lb-ft3 Nm
- Mounting Bracket Bolts21 lb-ft28 Nm
AC Hose Assembly6 specs
- AC Line FittingsUse new O-rings, add PAG oil15 lb-ft20 Nm
- Blower Motor Mounting Screw3 lb-ft4 Nm
- Compressor Bolts18 lb-ft25 Nm
- Duct Clips2 lb-ft3 Nm
- Hose Clamps2 lb-ft3 Nm
- Mounting Bracket Bolts21 lb-ft28 Nm
AC Low Pressure Switch5 specs
- AC Line FittingsUse new O-rings, add PAG oil15 lb-ft20 Nm
- Blower Motor Mounting Screw3 lb-ft4 Nm
- Compressor Bolts29 lb-ft39 Nm
- Duct Clips2 lb-ft3 Nm
- Mounting Bracket Bolts21 lb-ft28 Nm
AC Orifice Tube5 specs
- AC Line FittingsUse new O-rings, add PAG oil15 lb-ft20 Nm
- Blower Motor Mounting Screw3 lb-ft4 Nm
- Compressor Bolts29 lb-ft39 Nm
- Duct Clips2 lb-ft3 Nm
- Mounting Bracket Bolts21 lb-ft28 Nm
AC Pressure Sensor5 specs
- AC Line FittingsUse new O-rings, add PAG oil15 lb-ft20 Nm
- Blower Motor Mounting Screw3 lb-ft4 Nm
- Compressor Bolts18 lb-ft25 Nm
- Duct Clips2 lb-ft3 Nm
- Mounting Bracket Bolts21 lb-ft28 Nm
AC Receiver/Drier6 specs
- AC Line FittingsUse new O-rings, add PAG oil15 lb-ft20 Nm
- Blower Motor Mounting Screw6 lb-ft8 Nm
- Compressor Bolts18 lb-ft25 Nm
- Duct Clips2 lb-ft3 Nm
- Mounting Bracket Bolts21 lb-ft28 Nm
- Receiver Drier Bolts7 lb-ft10 Nm
AC Recharge4 specs
- Blower Motor Mounting Screw3 lb-ft4 Nm
- Compressor Bolts18 lb-ft25 Nm
- Duct Clips2 lb-ft3 Nm
- Mounting Bracket Bolts21 lb-ft28 Nm
Blend Door Actuator5 specs
- Actuator Screws2 lb-ft3 Nm
- Blower Motor Mounting Screw6 lb-ft8 Nm
- Compressor Bolts18 lb-ft25 Nm
- Duct Clips2 lb-ft3 Nm
- Mounting Bracket Bolts21 lb-ft28 Nm
Cabin Air Filter4 specs
- Compressor Bolts29 lb-ft39 Nm
- Connector Bolts6 lb-ft8 Nm
- Filter Cover ClipsTool-free on most2 lb-ft3 Nm
- Glove Box Screws3 lb-ft4 Nm
Climate Control Module5 specs
- AC Line FittingsUse new O-rings, add PAG oil15 lb-ft20 Nm
- Blower Motor Mounting Screw3 lb-ft4 Nm
- Compressor Bolts18 lb-ft25 Nm
- Duct Clips2 lb-ft3 Nm
- Mounting Bracket Bolts21 lb-ft28 Nm
HVAC Control Panel5 specs
- AC Line FittingsUse new O-rings, add PAG oil15 lb-ft20 Nm
- Blower Motor Mounting Screw3 lb-ft4 Nm
- Compressor Bolts18 lb-ft25 Nm
- Duct Clips2 lb-ft3 Nm
- Mounting Bracket Bolts21 lb-ft28 Nm
Mode Door Actuator4 specs
- Blower Motor Mounting Screw3 lb-ft4 Nm
- Compressor Bolts29 lb-ft39 Nm
- Duct Clips2 lb-ft3 Nm
- Mounting Bracket Bolts21 lb-ft28 Nm
Recirculation Door Actuator5 specs
- AC Line FittingsUse new O-rings, add PAG oil15 lb-ft20 Nm
- Blower Motor Mounting Screw3 lb-ft4 Nm
- Compressor Bolts18 lb-ft25 Nm
- Duct Clips2 lb-ft3 Nm
- Mounting Bracket Bolts21 lb-ft28 Nm

Body

Bumper Cover - Front8 specs
- Bumper Cover Bolts7 lb-ft10 Nm
- Fender Liner Screws2 lb-ft3 Nm
- Grille Clips4 lb-ft5 Nm
- Hinge Bolts23 lb-ft31 Nm
- Latch Bolts12 lb-ft16 Nm
- Panel Bolts12 lb-ft16 Nm
- Striker Bolts29 lb-ft39 Nm
- Trim ClipsReplace if broken2 lb-ft3 Nm
Bumper Cover - Rear7 specs
- Bumper Cover Bolts7 lb-ft10 Nm
- Hinge Bolts23 lb-ft31 Nm
- Latch Bolts12 lb-ft16 Nm
- Panel Bolts12 lb-ft16 Nm
- Striker Bolts29 lb-ft39 Nm
- Trim ClipsReplace if broken2 lb-ft3 Nm
- Trunk Liner Screws2 lb-ft3 Nm
Bumper Reinforcement - Front8 specs
- Body Panel Bolts18 lb-ft25 Nm
- Bumper Cover Bolts7 lb-ft10 Nm
- Door Hinge Bolts22 lb-ft30 Nm
- Hinge Bolts23 lb-ft31 Nm
- Latch Bolts12 lb-ft16 Nm
- Panel Bolts12 lb-ft16 Nm
- Striker Bolts29 lb-ft39 Nm
- Trim ClipsReplace if broken2 lb-ft3 Nm
Bumper Reinforcement - Rear8 specs
- Body Panel Bolts18 lb-ft25 Nm
- Bumper Cover Bolts7 lb-ft10 Nm
- Door Hinge Bolts22 lb-ft30 Nm
- Hinge Bolts23 lb-ft31 Nm
- Latch Bolts12 lb-ft16 Nm
- Panel Bolts12 lb-ft16 Nm
- Striker Bolts29 lb-ft39 Nm
- Trim ClipsReplace if broken2 lb-ft3 Nm
Door Check/Stop6 specs
- Body Panel Bolts18 lb-ft25 Nm
- Hinge Bolts23 lb-ft31 Nm
- Latch Bolts12 lb-ft16 Nm
- Panel Bolts12 lb-ft16 Nm
- Striker Bolts18 lb-ft24 Nm
- Trim ClipsReplace if broken2 lb-ft3 Nm
Door Glass5 specs
- Hinge Bolts23 lb-ft31 Nm
- Latch Bolts12 lb-ft16 Nm
- Panel Bolts12 lb-ft16 Nm
- Striker Bolts18 lb-ft24 Nm
- Trim ClipsReplace if broken2 lb-ft3 Nm
Door Handle - Exterior7 specs
- Handle Mounting Bolts6 lb-ft8 Nm
- Hinge Bolts23 lb-ft31 Nm
- Latch Bolts12 lb-ft16 Nm
- Lock Rod Clips4 lb-ft5 Nm
- Panel Bolts12 lb-ft16 Nm
- Striker Bolts29 lb-ft39 Nm
- Trim ClipsReplace if broken2 lb-ft3 Nm
Door Handle - Interior7 specs
- Cable Clips4 lb-ft5 Nm
- Handle Screws2 lb-ft3 Nm
- Hinge Bolts23 lb-ft31 Nm
- Latch Bolts12 lb-ft16 Nm
- Panel Bolts12 lb-ft16 Nm
- Striker Bolts29 lb-ft39 Nm
- Trim ClipsReplace if broken2 lb-ft3 Nm
Door Hinge6 specs
- Door Hinge Bolts22 lb-ft30 Nm
- Hinge Bolts23 lb-ft31 Nm
- Latch Bolts12 lb-ft16 Nm
- Panel Bolts12 lb-ft16 Nm
- Striker Bolts18 lb-ft24 Nm
- Trim ClipsReplace if broken2 lb-ft3 Nm
Door Shell7 specs
- Body Panel Bolts18 lb-ft25 Nm
- Door Hinge Bolts22 lb-ft30 Nm
- Hinge Bolts23 lb-ft31 Nm
- Latch Bolts12 lb-ft16 Nm
- Panel Bolts12 lb-ft16 Nm
- Striker Bolts18 lb-ft24 Nm
- Trim ClipsReplace if broken2 lb-ft3 Nm
Door Skin7 specs
- Body Panel Bolts18 lb-ft25 Nm
- Door Hinge Bolts22 lb-ft30 Nm
- Hinge Bolts23 lb-ft31 Nm
- Latch Bolts12 lb-ft16 Nm
- Panel Bolts12 lb-ft16 Nm
- Striker Bolts18 lb-ft24 Nm
- Trim ClipsReplace if broken2 lb-ft3 Nm
Door Weatherstrip5 specs
- Hinge Bolts23 lb-ft31 Nm
- Latch Bolts12 lb-ft16 Nm
- Panel Bolts12 lb-ft16 Nm
- Striker Bolts18 lb-ft24 Nm
- Trim ClipsReplace if broken2 lb-ft3 Nm
Fender8 specs
- Fender Bolts9 lb-ft12 Nm
- Fender Liner Screws2 lb-ft3 Nm
- Hinge Bolts23 lb-ft31 Nm
- Hood Hinge Bolts18 lb-ft25 Nm
- Latch Bolts12 lb-ft16 Nm
- Panel Bolts12 lb-ft16 Nm
- Striker Bolts29 lb-ft39 Nm
- Trim ClipsReplace if broken2 lb-ft3 Nm
Fender Liner8 specs
- Body Panel Bolts18 lb-ft25 Nm
- Bumper Cover Bolts7 lb-ft10 Nm
- Door Hinge Bolts22 lb-ft30 Nm
- Hinge Bolts23 lb-ft31 Nm
- Latch Bolts12 lb-ft16 Nm
- Panel Bolts12 lb-ft16 Nm
- Striker Bolts29 lb-ft39 Nm
- Trim ClipsReplace if broken2 lb-ft3 Nm
Grille7 specs
- Clips4 lb-ft5 Nm
- Grille Mounting Screws2 lb-ft3 Nm
- Hinge Bolts23 lb-ft31 Nm
- Latch Bolts12 lb-ft16 Nm
- Panel Bolts12 lb-ft16 Nm
- Striker Bolts29 lb-ft39 Nm
- Trim ClipsReplace if broken2 lb-ft3 Nm
Hood8 specs
- Hinge Bolts16 lb-ft22 Nm
- Hood Hinge Bolts18 lb-ft25 Nm
- Hood Latch Bolts9 lb-ft12 Nm
- Hood Strut Bolts7 lb-ft10 Nm
- Latch Bolts12 lb-ft16 Nm
- Panel Bolts12 lb-ft16 Nm
- Striker Bolts29 lb-ft39 Nm
- Trim ClipsReplace if broken2 lb-ft3 Nm
Hood Hinge7 specs
- Body Panel Bolts18 lb-ft25 Nm
- Door Hinge Bolts18 lb-ft25 Nm
- Hinge Bolts16 lb-ft22 Nm
- Latch Bolts12 lb-ft16 Nm
- Panel Bolts12 lb-ft16 Nm
- Striker Bolts7 lb-ft9 Nm
- Trim ClipsReplace if broken2 lb-ft3 Nm
Hood Latch7 specs
- Cable Clips4 lb-ft5 Nm
- Hinge Bolts23 lb-ft31 Nm
- Hood Latch Bolts9 lb-ft12 Nm
- Latch Bolts12 lb-ft16 Nm
- Panel Bolts12 lb-ft16 Nm
- Striker Bolts7 lb-ft9 Nm
- Trim ClipsReplace if broken2 lb-ft3 Nm
Hood Release Cable7 specs
- Body Panel Bolts18 lb-ft25 Nm
- Bumper Cover Bolts7 lb-ft10 Nm
- Hinge Bolts23 lb-ft31 Nm
- Latch Bolts12 lb-ft16 Nm
- Panel Bolts12 lb-ft16 Nm
- Striker Bolts7 lb-ft9 Nm
- Trim ClipsReplace if broken2 lb-ft3 Nm
Hood Strut6 specs
- Body Panel Bolts18 lb-ft25 Nm
- Hinge Bolts23 lb-ft31 Nm
- Latch Bolts12 lb-ft16 Nm
- Panel Bolts12 lb-ft16 Nm
- Striker Bolts7 lb-ft9 Nm
- Trim ClipsReplace if broken2 lb-ft3 Nm
Quarter Glass6 specs
- Body Panel Bolts18 lb-ft25 Nm
- Hinge Bolts23 lb-ft31 Nm
- Latch Bolts12 lb-ft16 Nm
- Panel Bolts12 lb-ft16 Nm
- Striker Bolts29 lb-ft39 Nm
- Trim ClipsReplace if broken2 lb-ft3 Nm
Quarter Panel8 specs
- Body Panel Bolts18 lb-ft25 Nm
- Bumper Cover Bolts7 lb-ft10 Nm
- Door Hinge Bolts33 lb-ft45 Nm
- Hinge Bolts23 lb-ft31 Nm
- Latch Bolts12 lb-ft16 Nm
- Panel Bolts12 lb-ft16 Nm
- Striker Bolts29 lb-ft39 Nm
- Trim ClipsReplace if broken2 lb-ft3 Nm
Rear Window6 specs
- Body Panel Bolts18 lb-ft25 Nm
- Hinge Bolts23 lb-ft31 Nm
- Latch Bolts12 lb-ft16 Nm
- Panel Bolts12 lb-ft16 Nm
- Striker Bolts29 lb-ft39 Nm
- Trim ClipsReplace if broken2 lb-ft3 Nm
Rocker Panel8 specs
- Body Panel Bolts18 lb-ft25 Nm
- Bumper Cover Bolts7 lb-ft10 Nm
- Door Hinge Bolts33 lb-ft45 Nm
- Hinge Bolts33 lb-ft45 Nm
- Latch Bolts12 lb-ft16 Nm
- Panel Bolts12 lb-ft16 Nm
- Striker Bolts18 lb-ft24 Nm
- Trim ClipsReplace if broken2 lb-ft3 Nm
Side Mirror Glass6 specs
- Door Hinge Bolts22 lb-ft30 Nm
- Hinge Bolts23 lb-ft31 Nm
- Latch Bolts12 lb-ft16 Nm
- Panel Bolts12 lb-ft16 Nm
- Striker Bolts29 lb-ft39 Nm
- Trim ClipsReplace if broken2 lb-ft3 Nm
Trunk Hinge7 specs
- Body Panel Bolts18 lb-ft25 Nm
- Door Hinge Bolts22 lb-ft30 Nm
- Hinge Bolts16 lb-ft22 Nm
- Latch Bolts12 lb-ft16 Nm
- Panel Bolts12 lb-ft16 Nm
- Striker Bolts15 lb-ft20 Nm
- Trim ClipsReplace if broken2 lb-ft3 Nm
Trunk Latch6 specs
- Body Panel Bolts18 lb-ft25 Nm
- Hinge Bolts16 lb-ft22 Nm
- Latch Bolts12 lb-ft16 Nm
- Panel Bolts12 lb-ft16 Nm
- Striker Bolts15 lb-ft20 Nm
- Trim ClipsReplace if broken2 lb-ft3 Nm
Trunk Lid7 specs
- Hinge Bolts16 lb-ft22 Nm
- Latch Bolts12 lb-ft16 Nm
- Panel Bolts12 lb-ft16 Nm
- Striker Bolts15 lb-ft20 Nm
- Trim ClipsReplace if broken2 lb-ft3 Nm
- Trunk Hinge Bolts18 lb-ft25 Nm
- Trunk Latch Bolts9 lb-ft12 Nm
Trunk Strut6 specs
- Body Panel Bolts18 lb-ft25 Nm
- Hinge Bolts23 lb-ft31 Nm
- Latch Bolts12 lb-ft16 Nm
- Panel Bolts12 lb-ft16 Nm
- Striker Bolts29 lb-ft39 Nm
- Trim ClipsReplace if broken2 lb-ft3 Nm
Windshield7 specs
- Body Panel Bolts18 lb-ft25 Nm
- Door Hinge Bolts33 lb-ft45 Nm
- Hinge Bolts33 lb-ft45 Nm
- Latch Bolts12 lb-ft16 Nm
- Panel Bolts12 lb-ft16 Nm
- Striker Bolts18 lb-ft24 Nm
- Trim ClipsReplace if broken2 lb-ft3 Nm
Windshield Molding6 specs
- Door Hinge Bolts33 lb-ft45 Nm
- Hinge Bolts33 lb-ft45 Nm
- Latch Bolts12 lb-ft16 Nm
- Panel Bolts12 lb-ft16 Nm
- Striker Bolts18 lb-ft24 Nm
- Trim ClipsReplace if broken2 lb-ft3 Nm

Interior

Armrest3 specs
- Connector Bolts6 lb-ft8 Nm
- Seat Mounting BoltsSafety critical7 lb-ft9 Nm
- Trim Panel ClipsReplace if damaged1.5 lb-ft2 Nm
Carpet4 specs
- Connector Bolts6 lb-ft8 Nm
- Dashboard Screws2 lb-ft3 Nm
- Seat Mounting BoltsSafety critical33 lb-ft45 Nm
- Trim Panel ClipsReplace if damaged1.5 lb-ft2 Nm
Center Console3 specs
- Connector Bolts6 lb-ft8 Nm
- Console Screws2 lb-ft3 Nm
- Shifter Trim4 lb-ft5 Nm
Dash Pad4 specs
- Connector Bolts6 lb-ft8 Nm
- Dashboard Screws2 lb-ft3 Nm
- Seat Mounting BoltsSafety critical33 lb-ft45 Nm
- Trim Panel ClipsReplace if damaged1.5 lb-ft2 Nm
Dashboard4 specs
- Connector Bolts6 lb-ft8 Nm
- Dashboard Bolt9 lb-ft12 Nm
- Dashboard Screws2 lb-ft3 Nm
- Trim Panel ClipsReplace if damaged1.5 lb-ft2 Nm
Door Panel3 specs
- Connector Bolts6 lb-ft8 Nm
- Door Panel Screws1.5 lb-ft2 Nm
- Trim Panel ClipsReplace if damaged1.5 lb-ft2 Nm
Floor Mat Hooks3 specs
- Connector Bolts6 lb-ft8 Nm
- Seat Mounting BoltsSafety critical33 lb-ft45 Nm
- Trim Panel ClipsReplace if damaged1.5 lb-ft2 Nm
Glove Box3 specs
- Connector Bolts6 lb-ft8 Nm
- Glove Box Screws2 lb-ft3 Nm
- Hinge Screws1.5 lb-ft2 Nm
Glove Box Latch3 specs
- Connector Bolts6 lb-ft8 Nm
- Dashboard Screws2 lb-ft3 Nm
- Trim Panel ClipsReplace if damaged1.5 lb-ft2 Nm
Headliner3 specs
- Connector Bolts6 lb-ft8 Nm
- Seat Mounting BoltsSafety critical33 lb-ft45 Nm
- Trim Panel ClipsReplace if damaged1.5 lb-ft2 Nm
Pedal Pads2 specs
- Connector Bolts6 lb-ft8 Nm
- Trim Panel ClipsReplace if damaged1.5 lb-ft2 Nm
Rearview Mirror2 specs
- Connector Bolts6 lb-ft8 Nm
- Trim Panel ClipsReplace if damaged1.5 lb-ft2 Nm
Seat - Front4 specs
- Connector Bolts6 lb-ft8 Nm
- Electrical Connectors4 lb-ft5 Nm
- Seat Mounting BoltsSafety critical33 lb-ft45 Nm
- Seat Track Bolts33 lb-ft45 Nm
Seat - Rear3 specs
- Connector Bolts6 lb-ft8 Nm
- Seat Back Release11 lb-ft15 Nm
- Seat Mounting Bolts26 lb-ft35 Nm
Seat Belt3 specs
- Connector Bolts6 lb-ft8 Nm
- Seat Mounting BoltsSafety critical33 lb-ft45 Nm
- Trim Panel ClipsReplace if damaged1.5 lb-ft2 Nm
Seat Belt Buckle3 specs
- Connector Bolts6 lb-ft8 Nm
- Seat Mounting BoltsSafety critical33 lb-ft45 Nm
- Trim Panel ClipsReplace if damaged1.5 lb-ft2 Nm
Seat Belt Pretensioner3 specs
- Connector Bolts6 lb-ft8 Nm
- Seat Mounting BoltsSafety critical33 lb-ft45 Nm
- Trim Panel ClipsReplace if damaged1.5 lb-ft2 Nm
Seat Cover3 specs
- Connector Bolts6 lb-ft8 Nm
- Seat Mounting BoltsSafety critical33 lb-ft45 Nm
- Trim Panel ClipsReplace if damaged1.5 lb-ft2 Nm
Seat Foam3 specs
- Connector Bolts6 lb-ft8 Nm
- Seat Mounting BoltsSafety critical33 lb-ft45 Nm
- Trim Panel ClipsReplace if damaged1.5 lb-ft2 Nm
Seat Track3 specs
- Connector Bolts6 lb-ft8 Nm
- Seat Mounting BoltsSafety critical33 lb-ft45 Nm
- Trim Panel ClipsReplace if damaged1.5 lb-ft2 Nm
Shifter Boot2 specs
- Connector Bolts6 lb-ft8 Nm
- Trim Panel ClipsReplace if damaged1.5 lb-ft2 Nm
Shifter Knob2 specs
- Connector Bolts6 lb-ft8 Nm
- Trim Panel ClipsReplace if damaged1.5 lb-ft2 Nm
Steering Wheel Cover4 specs
- Connector Bolts6 lb-ft8 Nm
- Dashboard ScrewsVerify sequence with the service manual2 lb-ft3 Nm
- Seat Mounting BoltsSafety critical. Verify sequence with the service manual33 lb-ft45 Nm
- Trim Panel ClipsReplace if damaged. Verify sequence with the service manual1.5 lb-ft2 Nm
Sun Visor2 specs
- Connector Bolts6 lb-ft8 Nm
- Visor Mounting Screws2 lb-ft3 Nm

Torque is shown in lb-ft with Nm below it. Where a step says to turn, tighten the listed angle after the torque step before it. Use new bolts where the note says so.

Need labor times, fluids or repair steps for this car? See it on the Open Labor Project