1994 Kia Sephia torque specs

1.6L I4

These specs cover the Kia Sephia 1.6L I4 for model years 1994, 1995, 1996, 1997.

Change vehicle

Verified specs were transcribed from OEM workshop data or checked by hand.

Most looked up

Lug nuts65 lb-ft88 Nm
Oil drain plug30 lb-ft40 Nm
Spark plugs15 lb-ft20 Nm
Front caliper bracket bolts88 lb-ft120 Nm
Rear caliper bracket bolts74 lb-ft100 Nm
Front axle nut170 lb-ft230 Nm
Outer tie rod end nut32 lb-ft44 Nm

Maintenance

AC System Diagnosis5 specs
- AC Line FittingsNew O-rings14 lb-ft19 Nm
- Air Box Clips4 lb-ft5 Nm
- Connector Bolts5 lb-ft7 Nm
- Oil Drain PlugUse new crush washer26 lb-ft35 Nm
- Wheel Lug NutsTorque in star pattern65 lb-ft88 Nm
Air Filter4 specs
- Air Box Clips4 lb-ft5 Nm
- Intake Tube Clamp3 lb-ft4 Nm
- MAF Sensor Screws3 lb-ft4 Nm
- Mass Air Flow Sensor Screws2 lb-ft3 Nm
Battery Test7 specs
- Air Box Clips4 lb-ft5 Nm
- Battery Hold-Down BoltDo not overtighten8 lb-ft10 Nm
- Battery Terminal BoltsClean terminals5 lb-ft6 Nm
- Connector Bolts5 lb-ft7 Nm
- Ground Cable Bolt10 lb-ft13 Nm
- Oil Drain PlugUse new crush washer26 lb-ft35 Nm
- Wheel Lug NutsTorque in star pattern65 lb-ft88 Nm
Charging System Test4 specs
- Air Box Clips4 lb-ft5 Nm
- Connector Bolts5 lb-ft7 Nm
- Oil Drain PlugUse new crush washer26 lb-ft35 Nm
- Wheel Lug NutsTorque in star pattern65 lb-ft88 Nm
Check Engine Light Diagnosis4 specs
- Air Box Clips4 lb-ft5 Nm
- Connector Bolts5 lb-ft7 Nm
- Oil Drain PlugUse new crush washer26 lb-ft35 Nm
- Wheel Lug NutsTorque in star pattern65 lb-ft88 Nm
Compression Test4 specs
- Air Box Clips4 lb-ft5 Nm
- Connector Bolts5 lb-ft7 Nm
- Oil Drain PlugUse new crush washer26 lb-ft35 Nm
- Wheel Lug NutsTorque in star pattern65 lb-ft88 Nm
Cooling System Pressure Test4 specs
- Air Box Clips4 lb-ft5 Nm
- Connector Bolts5 lb-ft7 Nm
- Oil Drain PlugUse new crush washer26 lb-ft35 Nm
- Wheel Lug NutsTorque in star pattern65 lb-ft88 Nm
Diagnostic Scan4 specs
- Air Box Clips4 lb-ft5 Nm
- Connector Bolts5 lb-ft7 Nm
- Oil Drain PlugUse new crush washer26 lb-ft35 Nm
- Wheel Lug NutsTorque in star pattern65 lb-ft88 Nm
Differential Service3 specs
- Connector Bolts5 lb-ft7 Nm
- Drain PlugNew washer29 lb-ft39 Nm
- Fill Plug29 lb-ft39 Nm
Drivability Diagnosis4 specs
- Air Box Clips4 lb-ft5 Nm
- Connector Bolts5 lb-ft7 Nm
- Oil Drain PlugUse new crush washer26 lb-ft35 Nm
- Wheel Lug NutsTorque in star pattern65 lb-ft88 Nm
Electrical Diagnosis4 specs
- Air Box Clips4 lb-ft5 Nm
- Connector Bolts5 lb-ft7 Nm
- Oil Drain PlugUse new crush washer26 lb-ft35 Nm
- Wheel Lug NutsTorque in star pattern65 lb-ft88 Nm
Fluid Leak Diagnosis4 specs
- Air Box Clips4 lb-ft5 Nm
- Connector Bolts5 lb-ft7 Nm
- Oil Drain PlugUse new crush washer26 lb-ft35 Nm
- Wheel Lug NutsTorque in star pattern65 lb-ft88 Nm
Leak-Down Test4 specs
- Air Box Clips4 lb-ft5 Nm
- Connector Bolts5 lb-ft7 Nm
- Oil Drain PlugUse new crush washer26 lb-ft35 Nm
- Wheel Lug NutsTorque in star pattern65 lb-ft88 Nm
Noise Diagnosis4 specs
- Air Box Clips4 lb-ft5 Nm
- Connector Bolts5 lb-ft7 Nm
- Oil Drain PlugUse new crush washer26 lb-ft35 Nm
- Wheel Lug NutsTorque in star pattern65 lb-ft88 Nm
Power Steering Service6 specs
- Air Box ClipsVerify sequence with the service manual4 lb-ft5 Nm
- Connector Bolts5 lb-ft7 Nm
- Oil Drain PlugUse new crush washer. Verify sequence with the service manual26 lb-ft35 Nm
- Pressure Line FittingNew O-ring24 lb-ft32 Nm
- Pump Mounting Bolts19 lb-ft26 Nm
- Wheel Lug NutsTorque in star pattern. Verify sequence with the service manual65 lb-ft88 Nm
Tire Balance4 specs
- Air Box Clips4 lb-ft5 Nm
- Connector Bolts5 lb-ft7 Nm
- Oil Drain PlugUse new crush washer26 lb-ft35 Nm
- Wheel Lug NutsTorque in star pattern65 lb-ft88 Nm
Tire Mount and Balance4 specs
- Air Box Clips4 lb-ft5 Nm
- Connector Bolts5 lb-ft7 Nm
- Oil Drain PlugUse new crush washer26 lb-ft35 Nm
- Wheel Lug NutsTorque in star pattern65 lb-ft88 Nm
Tire Rotation2 specs
- Lug Nuts - Alloy WheelsTorque in star pattern, recheck after 50 miles65 lb-ft88 Nm
- Lug Nuts - Steel WheelsTorque in star pattern65 lb-ft88 Nm
Transmission Service4 specs
- Air Box Clips4 lb-ft5 Nm
- Connector Bolts5 lb-ft7 Nm
- Oil Drain PlugUse new crush washer26 lb-ft35 Nm
- Wheel Lug NutsTorque in star pattern65 lb-ft88 Nm
Tune-Up - Major4 specs
- Air Box Clips4 lb-ft5 Nm
- Connector Bolts5 lb-ft7 Nm
- Oil Drain PlugUse new crush washer26 lb-ft35 Nm
- Wheel Lug NutsTorque in star pattern65 lb-ft88 Nm
Tune-Up - Minor4 specs
- Air Box Clips4 lb-ft5 Nm
- Connector Bolts5 lb-ft7 Nm
- Oil Drain PlugUse new crush washer26 lb-ft35 Nm
- Wheel Lug NutsTorque in star pattern65 lb-ft88 Nm
Wheel Alignment9 specs
- Air Box Clips4 lb-ft5 Nm
- Cam BoltsAfter adjustment90 lb-ft122 Nm
- Camber BoltsIf adjustable55 lb-ft75 Nm
- Connector Bolts5 lb-ft7 Nm
- Oil Drain PlugUse new crush washer26 lb-ft35 Nm
- Subframe BoltsIf adjusted81 lb-ft110 Nm
- Tie Rod Jam Nuts41 lb-ft55 Nm
- Tie Rod Lock NutAfter adjustment48 lb-ft65 Nm
- Wheel Lug NutsTorque in star pattern65 lb-ft88 Nm

Brakes

ABS Module5 specs
- ABS Module Bolts7 lb-ft10 Nm
- Bleeder Screw10 lb-ft14 Nm
- Brake Line FittingsUse flare nut wrench11 lb-ft15 Nm
- Caliper Mounting BoltsUse thread locker62 lb-ft84 Nm
- Wheel Lug NutsTorque in star pattern65 lb-ft88 Nm
ABS Pump5 specs
- Bleeder ScrewDo not overtighten7 lb-ft10 Nm
- Caliper Bracket Bolts - FrontThreadlocker recommended88 lb-ft120 Nm
- Caliper Mounting BoltsUse thread locker62 lb-ft84 Nm
- Caliper Slide Pin BoltsApply silicone brake grease26 lb-ft35 Nm
- Wheel Lug NutsTorque in star pattern65 lb-ft88 Nm
ABS Tone Ring5 specs
- Bleeder ScrewDo not overtighten7 lb-ft10 Nm
- Caliper Bracket Bolts - FrontThreadlocker recommended88 lb-ft120 Nm
- Caliper Mounting BoltsUse thread locker62 lb-ft84 Nm
- Caliper Slide Pin BoltsApply silicone brake grease26 lb-ft35 Nm
- Wheel Lug NutsTorque in star pattern65 lb-ft88 Nm
ABS Wheel Speed Sensor - Front5 specs
- ABS Sensor BoltDo not overtighten7 lb-ft10 Nm
- Bleeder Screw10 lb-ft14 Nm
- Caliper Mounting BoltsUse thread locker62 lb-ft84 Nm
- Wheel Bearing Hub Bolts81 lb-ft110 Nm
- Wheel Lug NutsTorque in star pattern65 lb-ft88 Nm
ABS Wheel Speed Sensor - Rear4 specs
- ABS Sensor BoltDo not overtighten7 lb-ft10 Nm
- Bleeder Screw10 lb-ft14 Nm
- Caliper Mounting BoltsUse thread locker62 lb-ft84 Nm
- Wheel Lug NutsTorque in star pattern65 lb-ft88 Nm
Brake Bleed - All Four5 specs
- Bleeder ScrewDo not overtighten. Verify sequence with the service manual7 lb-ft10 Nm
- Caliper Bracket Bolts - FrontThreadlocker recommended. Verify sequence with the service manual88 lb-ft120 Nm
- Caliper Mounting BoltsUse thread locker62 lb-ft84 Nm
- Caliper Slide Pin BoltsApply silicone brake grease. Verify sequence with the service manual26 lb-ft35 Nm
- Wheel Lug NutsTorque in star pattern. Verify sequence with the service manual65 lb-ft88 Nm
Brake Booster6 specs
- Bleeder Screw10 lb-ft14 Nm
- Brake Booster NutsVerify sequence with the service manual18 lb-ft25 Nm
- Brake Pedal Pushrod LockVerify sequence with the service manual11 lb-ft15 Nm
- Caliper Mounting BoltsUse thread locker62 lb-ft84 Nm
- Master Cylinder NutsVerify sequence with the service manual18 lb-ft25 Nm
- Wheel Lug NutsTorque in star pattern65 lb-ft88 Nm
Brake Booster Check Valve5 specs
- Bleeder ScrewDo not overtighten. Verify sequence with the service manual7 lb-ft10 Nm
- Caliper Bracket Bolts - FrontThreadlocker recommended. Verify sequence with the service manual88 lb-ft120 Nm
- Caliper Mounting BoltsUse thread locker62 lb-ft84 Nm
- Caliper Slide Pin BoltsApply silicone brake grease. Verify sequence with the service manual26 lb-ft35 Nm
- Wheel Lug NutsTorque in star pattern. Verify sequence with the service manual65 lb-ft88 Nm
Brake Caliper - Front3 specs
- Bleeder ScrewDo not overtighten7 lb-ft10 Nm
- Brake Line Banjo BoltUse new copper washers18 lb-ft25 Nm
- Caliper Bracket BoltsThreadlocker recommended88 lb-ft120 Nm
Brake Caliper - Rear3 specs
- Bleeder ScrewDo not overtighten7 lb-ft10 Nm
- Brake Line Banjo BoltUse new copper washers18 lb-ft25 Nm
- Caliper Bracket BoltsThreadlocker recommended74 lb-ft100 Nm
Brake Caliper Bracket6 specs
- Bleeder ScrewDo not overtighten. Verify sequence with the service manual7 lb-ft10 Nm
- Brake Hose Banjo BoltNew copper washers29 lb-ft39 Nm
- Caliper Bracket Bolts - FrontThreadlocker recommended. Verify sequence with the service manual88 lb-ft120 Nm
- Caliper Mounting BoltsUse thread locker62 lb-ft84 Nm
- Caliper Slide Pin BoltsApply silicone brake grease. Verify sequence with the service manual26 lb-ft35 Nm
- Wheel Lug NutsTorque in star pattern. Verify sequence with the service manual65 lb-ft88 Nm
Brake Caliper Rebuild - Front5 specs
- Bleeder ScrewDo not overtighten7 lb-ft10 Nm
- Caliper Bracket Bolts - FrontThreadlocker recommended88 lb-ft120 Nm
- Caliper Mounting BoltsUse thread locker62 lb-ft84 Nm
- Caliper Slide Pin BoltsApply silicone brake grease26 lb-ft35 Nm
- Wheel Lug NutsTorque in star pattern65 lb-ft88 Nm
Brake Caliper Rebuild - Rear5 specs
- Bleeder ScrewDo not overtighten7 lb-ft10 Nm
- Caliper Bracket Bolts - FrontThreadlocker recommended88 lb-ft120 Nm
- Caliper Mounting BoltsUse thread locker62 lb-ft84 Nm
- Caliper Slide Pin BoltsApply silicone brake grease26 lb-ft35 Nm
- Wheel Lug NutsTorque in star pattern65 lb-ft88 Nm
Brake Caliper Slide Pins5 specs
- Bleeder ScrewDo not overtighten7 lb-ft10 Nm
- Caliper Bracket Bolts - FrontThreadlocker recommended88 lb-ft120 Nm
- Caliper Mounting BoltsUse thread locker62 lb-ft84 Nm
- Caliper Slide Pin BoltsApply silicone brake grease26 lb-ft35 Nm
- Wheel Lug NutsTorque in star pattern65 lb-ft88 Nm
Brake Drum - Rear5 specs
- Bleeder ScrewDo not overtighten. Verify sequence with the service manual7 lb-ft10 Nm
- Caliper Bracket Bolts - FrontThreadlocker recommended. Verify sequence with the service manual88 lb-ft120 Nm
- Caliper Mounting BoltsUse thread locker62 lb-ft84 Nm
- Caliper Slide Pin BoltsApply silicone brake grease. Verify sequence with the service manual26 lb-ft35 Nm
- Wheel Lug NutsTorque in star pattern. Verify sequence with the service manual65 lb-ft88 Nm
Brake Fluid Flush9 specs
- Air Box ClipsVerify sequence with the service manual4 lb-ft5 Nm
- Bleeder ScrewDo not overtighten. Verify sequence with the service manual7 lb-ft10 Nm
- Caliper Bracket Bolts - FrontThreadlocker recommended. Verify sequence with the service manual88 lb-ft120 Nm
- Caliper Mounting Bolts62 lb-ft84 Nm
- Caliper Slide Pin BoltsApply silicone brake grease. Verify sequence with the service manual26 lb-ft35 Nm
- Connector Bolts5 lb-ft7 Nm
- Master Cylinder CapHand tight3 lb-ft4 Nm
- Oil Drain PlugUse new crush washer. Verify sequence with the service manual26 lb-ft35 Nm
- Wheel Lug NutsTorque in star pattern. Verify sequence with the service manual65 lb-ft88 Nm
Brake Hose - Front5 specs
- Bleeder Screw10 lb-ft14 Nm
- Brake Hose Banjo BoltUse new copper washers. Verify sequence with the service manual18 lb-ft25 Nm
- Brake Hose BracketVerify sequence with the service manual7 lb-ft10 Nm
- Caliper Mounting BoltsUse thread locker62 lb-ft84 Nm
- Wheel Lug NutsTorque in star pattern65 lb-ft88 Nm
Brake Hose - Rear5 specs
- Bleeder Screw10 lb-ft14 Nm
- Brake Hose Banjo BoltUse new copper washers. Verify sequence with the service manual18 lb-ft25 Nm
- Brake Hose BracketVerify sequence with the service manual7 lb-ft10 Nm
- Caliper Mounting BoltsUse thread locker62 lb-ft84 Nm
- Wheel Lug NutsTorque in star pattern65 lb-ft88 Nm
Brake Light Switch5 specs
- Bleeder ScrewDo not overtighten. Verify sequence with the service manual7 lb-ft10 Nm
- Caliper Bracket Bolts - FrontThreadlocker recommended. Verify sequence with the service manual88 lb-ft120 Nm
- Caliper Mounting BoltsUse thread locker62 lb-ft84 Nm
- Caliper Slide Pin BoltsApply silicone brake grease. Verify sequence with the service manual26 lb-ft35 Nm
- Wheel Lug NutsTorque in star pattern. Verify sequence with the service manual65 lb-ft88 Nm
Brake Line - Single5 specs
- Bleeder ScrewDo not overtighten. Verify sequence with the service manual7 lb-ft10 Nm
- Caliper Bracket Bolts - FrontThreadlocker recommended. Verify sequence with the service manual88 lb-ft120 Nm
- Caliper Mounting BoltsUse thread locker62 lb-ft84 Nm
- Caliper Slide Pin BoltsApply silicone brake grease. Verify sequence with the service manual26 lb-ft35 Nm
- Wheel Lug NutsTorque in star pattern. Verify sequence with the service manual65 lb-ft88 Nm
Brake Lines - Complete Set5 specs
- Bleeder ScrewDo not overtighten. Verify sequence with the service manual7 lb-ft10 Nm
- Caliper Bracket Bolts - FrontThreadlocker recommended. Verify sequence with the service manual88 lb-ft120 Nm
- Caliper Mounting BoltsUse thread locker62 lb-ft84 Nm
- Caliper Slide Pin BoltsApply silicone brake grease. Verify sequence with the service manual26 lb-ft35 Nm
- Wheel Lug NutsTorque in star pattern. Verify sequence with the service manual65 lb-ft88 Nm
Brake Master Cylinder2 specs
- Brake Line FittingsUse flare nut wrench11 lb-ft15 Nm
- Master Cylinder Nuts18 lb-ft25 Nm
Brake Master Cylinder Rebuild3 specs
- Brake Line FittingsUse flare nut wrench11 lb-ft15 Nm
- Master Cylinder Mounting Nuts18 lb-ft25 Nm
- Reservoir Mounting Bolts6 lb-ft8 Nm
Brake Pads - Front3 specs
- Caliper Bracket BoltsThreadlocker recommended88 lb-ft120 Nm
- Caliper Slide Pin BoltsApply silicone brake grease26 lb-ft35 Nm
- Wheel Lug NutsTorque in star pattern65 lb-ft88 Nm
Brake Pads - Rear3 specs
- Caliper Bracket BoltsThreadlocker recommended74 lb-ft100 Nm
- Caliper Slide Pin BoltsApply silicone brake grease22 lb-ft30 Nm
- Wheel Lug NutsTorque in star pattern65 lb-ft88 Nm
Brake Pads and Rotors - Front7 specs
- Bleeder ScrewDo not overtighten. Verify sequence with the service manual7 lb-ft10 Nm
- Caliper Bracket BoltsUse thread locker71 lb-ft97 Nm
- Caliper Bracket Bolts - FrontThreadlocker recommended. Verify sequence with the service manual88 lb-ft120 Nm
- Caliper Mounting BoltsUse thread locker62 lb-ft84 Nm
- Caliper Slide BoltsLubricate pins29 lb-ft39 Nm
- Caliper Slide Pin BoltsApply silicone brake grease. Verify sequence with the service manual29 lb-ft39 Nm
- Wheel Lug NutsTorque in star pattern. Verify sequence with the service manual65 lb-ft88 Nm
Brake Pads and Rotors - Rear7 specs
- Bleeder ScrewDo not overtighten. Verify sequence with the service manual7 lb-ft10 Nm
- Caliper Bracket BoltsUse thread locker71 lb-ft97 Nm
- Caliper Bracket Bolts - FrontThreadlocker recommended. Verify sequence with the service manual88 lb-ft120 Nm
- Caliper Mounting BoltsUse thread locker62 lb-ft84 Nm
- Caliper Slide BoltsLubricate pins24 lb-ft32 Nm
- Caliper Slide Pin BoltsApply silicone brake grease. Verify sequence with the service manual26 lb-ft35 Nm
- Wheel Lug NutsTorque in star pattern. Verify sequence with the service manual65 lb-ft88 Nm
Brake Proportioning Valve5 specs
- Bleeder Screw10 lb-ft14 Nm
- Brake Line FittingsUse flare nut wrench. Verify sequence with the service manual11 lb-ft15 Nm
- Caliper Mounting BoltsUse thread locker62 lb-ft84 Nm
- Proportioning Valve BoltsVerify sequence with the service manual11 lb-ft15 Nm
- Wheel Lug NutsTorque in star pattern65 lb-ft88 Nm
Brake Rotor - Front Single8 specs
- Bleeder ScrewDo not overtighten. Verify sequence with the service manual7 lb-ft10 Nm
- Brake Rotor Set Screw5 lb-ft6 Nm
- Caliper Bracket Bolts71 lb-ft97 Nm
- Caliper Bracket Bolts - FrontThreadlocker recommended. Verify sequence with the service manual88 lb-ft120 Nm
- Caliper Mounting BoltsUse thread locker62 lb-ft84 Nm
- Caliper Slide Pin BoltsApply silicone brake grease. Verify sequence with the service manual29 lb-ft39 Nm
- Hub NutIf removed170 lb-ft230 Nm
- Wheel Lug NutsTorque in star pattern. Verify sequence with the service manual65 lb-ft88 Nm
Brake Rotor - Rear Single8 specs
- Bleeder ScrewDo not overtighten. Verify sequence with the service manual7 lb-ft10 Nm
- Brake Rotor Set Screw5 lb-ft6 Nm
- Caliper Bracket Bolts71 lb-ft97 Nm
- Caliper Bracket Bolts - FrontThreadlocker recommended. Verify sequence with the service manual88 lb-ft120 Nm
- Caliper Mounting BoltsUse thread locker62 lb-ft84 Nm
- Caliper Slide Pin BoltsApply silicone brake grease. Verify sequence with the service manual26 lb-ft35 Nm
- Hub NutIf removed171 lb-ft232 Nm
- Wheel Lug NutsTorque in star pattern. Verify sequence with the service manual65 lb-ft88 Nm
Brake Rotors - Front Pair8 specs
- Bleeder ScrewDo not overtighten. Verify sequence with the service manual7 lb-ft10 Nm
- Brake Rotor Set Screw5 lb-ft6 Nm
- Caliper Bracket Bolts71 lb-ft97 Nm
- Caliper Bracket Bolts - FrontThreadlocker recommended. Verify sequence with the service manual88 lb-ft120 Nm
- Caliper Mounting BoltsUse thread locker62 lb-ft84 Nm
- Caliper Slide Pin BoltsApply silicone brake grease. Verify sequence with the service manual29 lb-ft39 Nm
- Hub NutIf removed170 lb-ft230 Nm
- Wheel Lug NutsTorque in star pattern. Verify sequence with the service manual65 lb-ft88 Nm
Brake Rotors - Rear Pair8 specs
- Bleeder ScrewDo not overtighten. Verify sequence with the service manual7 lb-ft10 Nm
- Brake Rotor Set Screw5 lb-ft6 Nm
- Caliper Bracket Bolts71 lb-ft97 Nm
- Caliper Bracket Bolts - FrontThreadlocker recommended. Verify sequence with the service manual88 lb-ft120 Nm
- Caliper Mounting BoltsUse thread locker62 lb-ft84 Nm
- Caliper Slide Pin BoltsApply silicone brake grease. Verify sequence with the service manual26 lb-ft35 Nm
- Hub NutIf removed171 lb-ft232 Nm
- Wheel Lug NutsTorque in star pattern. Verify sequence with the service manual65 lb-ft88 Nm
Drum Brake Hardware Kit5 specs
- Bleeder ScrewDo not overtighten. Verify sequence with the service manual7 lb-ft10 Nm
- Caliper Bracket Bolts - FrontThreadlocker recommended. Verify sequence with the service manual88 lb-ft120 Nm
- Caliper Mounting BoltsUse thread locker62 lb-ft84 Nm
- Caliper Slide Pin BoltsApply silicone brake grease. Verify sequence with the service manual26 lb-ft35 Nm
- Wheel Lug NutsTorque in star pattern. Verify sequence with the service manual65 lb-ft88 Nm
Drum Brake Shoes - Rear5 specs
- Bleeder ScrewDo not overtighten. Verify sequence with the service manual7 lb-ft10 Nm
- Caliper Bracket Bolts - FrontThreadlocker recommended. Verify sequence with the service manual88 lb-ft120 Nm
- Caliper Mounting BoltsUse thread locker62 lb-ft84 Nm
- Caliper Slide Pin BoltsApply silicone brake grease. Verify sequence with the service manual26 lb-ft35 Nm
- Wheel Lug NutsTorque in star pattern. Verify sequence with the service manual65 lb-ft88 Nm
Electronic Parking Brake Motor5 specs
- Bleeder ScrewDo not overtighten. Verify sequence with the service manual7 lb-ft10 Nm
- Caliper Bracket Bolts - FrontThreadlocker recommended. Verify sequence with the service manual88 lb-ft120 Nm
- Caliper Mounting BoltsUse thread locker62 lb-ft84 Nm
- Caliper Slide Pin BoltsApply silicone brake grease. Verify sequence with the service manual26 lb-ft35 Nm
- Wheel Lug NutsTorque in star pattern. Verify sequence with the service manual65 lb-ft88 Nm
Front Brake Pad Replacement3 specs
- Caliper Bracket BoltsThreadlocker recommended88 lb-ft120 Nm
- Caliper Slide Pin BoltsApply silicone brake grease26 lb-ft35 Nm
- Wheel Lug NutsTorque in star pattern65 lb-ft88 Nm
Parking Brake Actuator5 specs
- Bleeder ScrewDo not overtighten. Verify sequence with the service manual7 lb-ft10 Nm
- Caliper Bracket Bolts - FrontThreadlocker recommended. Verify sequence with the service manual88 lb-ft120 Nm
- Caliper Mounting BoltsUse thread locker62 lb-ft84 Nm
- Caliper Slide Pin BoltsApply silicone brake grease. Verify sequence with the service manual26 lb-ft35 Nm
- Wheel Lug NutsTorque in star pattern. Verify sequence with the service manual65 lb-ft88 Nm
Parking Brake Cable5 specs
- Bleeder Screw10 lb-ft14 Nm
- Cable Bracket BoltsVerify sequence with the service manual9 lb-ft12 Nm
- Caliper Mounting BoltsUse thread locker62 lb-ft84 Nm
- Equalizer NutAdjust for proper tension. Verify sequence with the service manual11 lb-ft15 Nm
- Wheel Lug NutsTorque in star pattern65 lb-ft88 Nm
Parking Brake Shoes5 specs
- Adjuster LockVerify sequence with the service manual4 lb-ft5 Nm
- Bleeder Screw10 lb-ft14 Nm
- Caliper Mounting BoltsUse thread locker62 lb-ft84 Nm
- Hold-Down SpringsVerify sequence with the service manual6 lb-ft8 Nm
- Wheel Lug NutsTorque in star pattern. Verify sequence with the service manual65 lb-ft88 Nm
Rear Brake Shoe Replacement3 specs
- Backing Plate Bolts44 lb-ft60 Nm
- Wheel Cylinder Bolts9 lb-ft12 Nm
- Wheel Lug NutsTorque in star pattern65 lb-ft88 Nm
Wheel Cylinder5 specs
- Bleeder ScrewDo not overtighten7 lb-ft10 Nm
- Caliper Bracket Bolts - FrontThreadlocker recommended88 lb-ft120 Nm
- Caliper Mounting BoltsUse thread locker62 lb-ft84 Nm
- Caliper Slide Pin BoltsApply silicone brake grease26 lb-ft35 Nm
- Wheel Lug NutsTorque in star pattern65 lb-ft88 Nm

Engine

Camshaft Position Sensor5 specs
- Camshaft Position Sensor7 lb-ft10 Nm
- Electrical Connector Bolts5 lb-ft7 Nm
- Gasket Surface BoltsClean mating surfaces14 lb-ft19 Nm
- Sensor Mounting Bolts8 lb-ft11 Nm
- Valve Cover BoltsTighten in sequence7 lb-ft10 Nm
Camshaft R&R20 specs
- Cam Phaser BoltApply threadlocker, hold cam stationary48 lb-ft65 Nm
- Camshaft Bearing Cap BoltsTighten in sequence, 3 passes10 lb-ft14 Nm
- Camshaft Cap BoltsTighten in sequence from center outward, multiple passes10 lb-ft14 Nm
- Camshaft Position Sensor7 lb-ft10 Nm
- Camshaft Sprocket BoltsHold cam with wrench on hex59 lb-ft80 Nm
- Crankshaft Position Sensor7 lb-ft10 Nm
- Crankshaft Pulley BoltOften TTY - check spec, may require impact133 lb-ft180 Nm
- Electrical Connector Bolts5 lb-ft7 Nm
- Gasket Surface BoltsClean mating surfaces14 lb-ft19 Nm
- Oil Drain PlugUse new crush washer26 lb-ft35 Nm
- Rocker Arm BoltsTighten with cam lobe pointing away22 lb-ft30 Nm
- Rocker Arm Shaft BoltsTighten evenly in sequence18 lb-ft25 Nm
- Sensor Mounting Bolts8 lb-ft11 Nm
- Timing Chain Guide BoltsReplace if worn9 lb-ft12 Nm
- Timing Chain Idler Sprocket18 lb-ft25 Nm
- Timing Chain Tensioner BoltInstall with pin/clip to compress18 lb-ft25 Nm
- Timing Cover Bolts - 10mmTighten in sequence33 lb-ft45 Nm
- Timing Cover Bolts - 8mmTighten in sequence18 lb-ft25 Nm
- Valve Cover BoltsTighten in sequence7 lb-ft10 Nm
- VVT Solenoid Bolt7 lb-ft10 Nm
Connecting Rod Bearings4 specs
- Connecting Rod BoltsStep 1: 14 lb-ft (19 Nm). Step 2: +90 degrees14 lb-ft + 90°19 Nm
- Electrical Connector Bolts5 lb-ft7 Nm
- Gasket Surface BoltsClean mating surfaces14 lb-ft19 Nm
- Sensor Mounting Bolts8 lb-ft11 Nm
Crankshaft Position Sensor4 specs
- Crankshaft Position Sensor7 lb-ft10 Nm
- Electrical Connector Bolts5 lb-ft7 Nm
- Gasket Surface BoltsClean mating surfaces14 lb-ft19 Nm
- Sensor Mounting Bolts8 lb-ft11 Nm
Crankshaft R&R20 specs
- Connecting Rod BoltsTTY - critical torque plus angle33 lb-ft45 Nm
- Crankshaft Pulley BoltOften TTY, may need impact133 lb-ft180 Nm
- Cylinder Head BoltsTTY - tighten in sequence plus angle48 lb-ft65 Nm
- Electrical Connector Bolts5 lb-ft7 Nm
- Flexplate BoltsAutomatic transmissions63 lb-ft85 Nm
- Flywheel BoltsOften TTY, tighten in star pattern70 lb-ft95 Nm
- Front Main Seal Housing9 lb-ft12 Nm
- Gasket Surface BoltsClean mating surfaces14 lb-ft19 Nm
- Main Bearing Cap BoltsTTY - tighten in sequence plus angle55 lb-ft75 Nm
- Oil Drain PlugUse new crush washer26 lb-ft35 Nm
- Oil Pan BoltTighten in sequence9 lb-ft12 Nm
- Oil Pump Bolts9 lb-ft12 Nm
- Oil Pump Pickup Tube9 lb-ft12 Nm
- Rear Main Seal Housing9 lb-ft12 Nm
- Sensor Mounting Bolts8 lb-ft11 Nm
- Timing Chain Guide BoltsReplace if worn9 lb-ft12 Nm
- Timing Chain Tensioner BoltInstall with pin/clip to compress18 lb-ft25 Nm
- Timing Cover Bolts - 10mmTighten in sequence33 lb-ft45 Nm
- Timing Cover Bolts - 8mmTighten in sequence18 lb-ft25 Nm
- Transmission-to-Engine Bolts41 lb-ft55 Nm
Cylinder Head R&R4 specs
- Cylinder Head BoltsStep 1: 22 lb-ft (30 Nm). Step 2: +90 degrees. Step 3: +90 degrees22 lb-ft + 180°30 Nm
- Electrical Connector Bolts5 lb-ft7 Nm
- Gasket Surface BoltsClean mating surfaces14 lb-ft19 Nm
- Sensor Mounting Bolts8 lb-ft11 Nm
Cylinder Head Resurface7 specs
- Cylinder Head BoltsTTY - tighten in sequence plus angle48 lb-ft65 Nm
- Electrical Connector Bolts5 lb-ft7 Nm
- Exhaust Manifold NutsApply anti-seize, work hot-to-cold22 lb-ft30 Nm
- Gasket Surface BoltsClean mating surfaces14 lb-ft19 Nm
- Intake Manifold Bolt18 lb-ft25 Nm
- Sensor Mounting Bolts8 lb-ft11 Nm
- Valve Cover BoltsTighten in sequence7 lb-ft10 Nm
Engine Mount - Front3 specs
- Engine Mount Through-Bolt63 lb-ft85 Nm
- Engine Mount-to-Block Bolts48 lb-ft65 Nm
- Engine Mount-to-Frame Bolts55 lb-ft75 Nm
Engine Mount - Rear6 specs
- Electrical Connector Bolts5 lb-ft7 Nm
- Engine Mount Through-Bolt62 lb-ft84 Nm
- Engine Mount-to-Block Bolts48 lb-ft65 Nm
- Engine Mount-to-Frame Bolts43 lb-ft58 Nm
- Gasket Surface BoltsClean mating surfaces14 lb-ft19 Nm
- Sensor Mounting Bolts8 lb-ft11 Nm
Engine Mounts - All7 specs
- Electrical Connector Bolts5 lb-ft7 Nm
- Engine Mount Through-Bolt62 lb-ft84 Nm
- Engine Mount-to-Block Bolts48 lb-ft65 Nm
- Engine Mount-to-Frame Bolts43 lb-ft58 Nm
- Gasket Surface BoltsClean mating surfaces14 lb-ft19 Nm
- Sensor Mounting Bolts8 lb-ft11 Nm
- Transmission Mount Bolts48 lb-ft65 Nm
Engine R&R13 specs
- AC Compressor Bolts18 lb-ft25 Nm
- Alternator Mounting Bolts37 lb-ft50 Nm
- Electrical Connector Bolts5 lb-ft7 Nm
- Engine Mount-to-Block Bolts48 lb-ft65 Nm
- Engine Mount-to-Frame Bolts55 lb-ft75 Nm
- Exhaust Manifold NutsApply anti-seize, work hot-to-cold22 lb-ft30 Nm
- Flywheel BoltsOften TTY, tighten in star pattern70 lb-ft95 Nm
- Gasket Surface BoltsClean mating surfaces14 lb-ft19 Nm
- Oil Drain PlugUse new crush washer26 lb-ft35 Nm
- Power Steering Pump Bolts18 lb-ft25 Nm
- Sensor Mounting Bolts8 lb-ft11 Nm
- Starter Mounting Bolt37 lb-ft50 Nm
- Transmission-to-Engine Bolts41 lb-ft55 Nm
Engine Rebuild21 specs
- Balance Shaft Bolts18 lb-ft25 Nm
- Camshaft Bearing Cap BoltsTighten in sequence, 3 passes10 lb-ft14 Nm
- Camshaft Cap BoltsTighten in sequence from center outward, multiple passes10 lb-ft14 Nm
- Connecting Rod BoltsTTY - critical torque plus angle33 lb-ft45 Nm
- Crankshaft Pulley BoltOften TTY - check spec, may require impact133 lb-ft180 Nm
- Cylinder Head BoltsTTY - tighten in sequence plus angle48 lb-ft65 Nm
- Electrical Connector Bolts5 lb-ft7 Nm
- Exhaust Manifold NutsApply anti-seize, work hot-to-cold22 lb-ft30 Nm
- Flywheel BoltsOften TTY, tighten in star pattern70 lb-ft95 Nm
- Gasket Surface BoltsClean mating surfaces14 lb-ft19 Nm
- Intake Manifold Bolt18 lb-ft25 Nm
- Main Bearing Cap BoltsTTY - tighten in sequence plus angle55 lb-ft75 Nm
- Oil Drain PlugUse new crush washer26 lb-ft35 Nm
- Oil Pan BoltTighten in sequence9 lb-ft12 Nm
- Oil Pump Bolts9 lb-ft12 Nm
- Oil Pump Pickup Tube9 lb-ft12 Nm
- Sensor Mounting Bolts8 lb-ft11 Nm
- Timing Chain Guide BoltsReplace if worn9 lb-ft12 Nm
- Timing Chain Tensioner BoltInstall with pin/clip to compress18 lb-ft25 Nm
- Timing Cover Bolts - 8mmTighten in sequence18 lb-ft25 Nm
- Valve Cover BoltsTighten in sequence7 lb-ft10 Nm
Exhaust Manifold8 specs
- Electrical Connector Bolts5 lb-ft7 Nm
- Exhaust Flange BoltApply anti-seize. Verify sequence with the service manual33 lb-ft45 Nm
- Exhaust Manifold NutsApply anti-seize, work hot-to-cold. Verify sequence with the service manual22 lb-ft30 Nm
- Gasket Surface BoltsClean mating surfaces14 lb-ft19 Nm
- Hanger Bolts14 lb-ft19 Nm
- Heat Shield BoltsVerify sequence with the service manual7 lb-ft10 Nm
- O2 SensorAnti-seize threads33 lb-ft45 Nm
- Sensor Mounting Bolts8 lb-ft11 Nm
Exhaust Manifold Gasket3 specs
- Exhaust Manifold NutsApply anti-seize, work hot-to-cold22 lb-ft30 Nm
- Exhaust Manifold StudsIf replacing studs11 lb-ft15 Nm
- Heat Shield Bolts7 lb-ft10 Nm
Fan Belt Replacement3 specs
- Idler Pulley Bolt30 lb-ft40 Nm
- Tensioner Bolt18 lb-ft25 Nm
- Tensioner Pulley Bolt33 lb-ft45 Nm
Flexplate6 specs
- Electrical Connector Bolts5 lb-ft7 Nm
- Flexplate BoltsAutomatic transmissions. Verify sequence with the service manual63 lb-ft85 Nm
- Gasket Surface BoltsClean mating surfaces14 lb-ft19 Nm
- Sensor Mounting Bolts8 lb-ft11 Nm
- Torque Converter BoltsVerify sequence with the service manual37 lb-ft50 Nm
- Transmission-to-Engine BoltsVerify sequence with the service manual41 lb-ft55 Nm
Flywheel6 specs
- Drain PlugUse new washer24 lb-ft33 Nm
- Fill Plug24 lb-ft33 Nm
- Flexplate BoltsAutomatic transmissions63 lb-ft85 Nm
- Flywheel BoltsOften TTY - check specs, tighten in star pattern70 lb-ft95 Nm
- Transmission Drain PlugUse new crush washer if equipped22 lb-ft30 Nm
- Transmission Pan BoltsTighten in criss-cross pattern9 lb-ft12 Nm
Freeze Plug - Single4 specs
- Electrical Connector Bolts5 lb-ft7 Nm
- Freeze PlugUse sealant on edges7 lb-ft10 Nm
- Gasket Surface BoltsClean mating surfaces14 lb-ft19 Nm
- Sensor Mounting Bolts8 lb-ft11 Nm
Freeze Plugs - All4 specs
- Electrical Connector Bolts5 lb-ft7 Nm
- Freeze PlugUse sealant on edges7 lb-ft10 Nm
- Gasket Surface BoltsClean mating surfaces14 lb-ft19 Nm
- Sensor Mounting Bolts8 lb-ft11 Nm
Front Main Seal8 specs
- Crankshaft Pulley BoltOften TTY, may need impact133 lb-ft180 Nm
- Electrical Connector Bolts5 lb-ft7 Nm
- Gasket Surface BoltsClean mating surfaces14 lb-ft19 Nm
- Oil Drain PlugUse new crush washer26 lb-ft35 Nm
- Oil Pan BoltFront section only9 lb-ft12 Nm
- Sensor Mounting Bolts8 lb-ft11 Nm
- Timing Cover Bolts - 10mmTighten in sequence33 lb-ft45 Nm
- Timing Cover Bolts - 8mmTighten in sequence18 lb-ft25 Nm
Full Engine Tune-Up4 specs
- Ignition Coil Bolt6 lb-ft8 Nm
- Spark Plugs - Aluminum HeadApply anti-seize to threads15 lb-ft20 Nm
- Throttle Body Bolts7 lb-ft10 Nm
- Valve Cover BoltsTighten in sequence7 lb-ft10 Nm
Harmonic Balancer4 specs
- Crankshaft Pulley BoltOften TTY - check spec, may require impact. Verify sequence with the service manual133 lb-ft180 Nm
- Electrical Connector Bolts5 lb-ft7 Nm
- Gasket Surface BoltsClean mating surfaces14 lb-ft19 Nm
- Sensor Mounting Bolts8 lb-ft11 Nm
Head Gasket - Single6 specs
- Exhaust Manifold NutsApply anti-seize18 lb-ft25 Nm
- Intake Manifold BoltTighten in sequence18 lb-ft25 Nm
- Cylinder Head Bolts - Step 1Always use new TTY bolts30 lb-ft40 Nm
- Cylinder Head Bolts - Step 2Tighten in sequence59 lb-ft80 Nm
- Cylinder Head Bolts - Step 3Plus 90 degreesTurn 90°
- Cylinder Head Bolts - Step 4Plus 90 degreesTurn 90°
Head Gaskets - Both8 specs
- Camshaft Cap BoltsTorque sequence11 lb-ft15 Nm
- Cylinder Head BoltsStep 1: 22 lb-ft (30 Nm). Step 2: +90 degrees. Step 3: +90 degrees22 lb-ft + 180°30 Nm
- Electrical Connector Bolts5 lb-ft7 Nm
- Exhaust Manifold Nuts24 lb-ft32 Nm
- Gasket Surface BoltsClean mating surfaces14 lb-ft19 Nm
- Intake Manifold Bolt17 lb-ft23 Nm
- Sensor Mounting Bolts8 lb-ft11 Nm
- Valve Cover Bolts10 lb-ft13 Nm
Idle Air Control Valve4 specs
- Electrical Connector Bolts5 lb-ft7 Nm
- Gasket Surface BoltsClean mating surfaces14 lb-ft19 Nm
- IAC Valve Screws2 lb-ft3 Nm
- Sensor Mounting Bolts8 lb-ft11 Nm
Idler Pulley4 specs
- Electrical Connector Bolts5 lb-ft7 Nm
- Gasket Surface BoltsClean mating surfaces14 lb-ft19 Nm
- Idler Pulley Bolt33 lb-ft45 Nm
- Sensor Mounting Bolts8 lb-ft11 Nm
Intake Manifold7 specs
- Electrical Connector Bolts5 lb-ft7 Nm
- Fuel Rail BoltsVerify sequence with the service manual9 lb-ft12 Nm
- Gasket Surface BoltsClean mating surfaces14 lb-ft19 Nm
- Intake Manifold BoltTighten in sequence from center out. Verify sequence with the service manual18 lb-ft25 Nm
- PCV ValveVerify sequence with the service manual6 lb-ft8 Nm
- Sensor Mounting Bolts8 lb-ft11 Nm
- Throttle Body BoltsVerify sequence with the service manual7 lb-ft10 Nm
Intake Manifold Gasket3 specs
- Fuel Rail Bolts9 lb-ft12 Nm
- Intake Manifold BoltTighten in sequence from center out18 lb-ft25 Nm
- Throttle Body Bolts7 lb-ft10 Nm
Knock Sensor4 specs
- Electrical Connector Bolts5 lb-ft7 Nm
- Gasket Surface BoltsClean mating surfaces14 lb-ft19 Nm
- Knock SensorTorque critical for function15 lb-ft20 Nm
- Sensor Mounting Bolts8 lb-ft11 Nm
Lifter - Single7 specs
- Electrical Connector Bolts5 lb-ft7 Nm
- Gasket Surface BoltsClean mating surfaces14 lb-ft19 Nm
- Intake Manifold Bolt18 lb-ft25 Nm
- Rocker Arm BoltsTighten with cam lobe pointing away22 lb-ft30 Nm
- Rocker Arm Shaft BoltsTighten evenly in sequence18 lb-ft25 Nm
- Sensor Mounting Bolts8 lb-ft11 Nm
- Valve Cover BoltsTighten in sequence7 lb-ft10 Nm
Lifters/Tappets - All10 specs
- Camshaft Bearing Cap BoltsTighten in sequence, 3 passes10 lb-ft14 Nm
- Camshaft Cap BoltsTighten in sequence from center outward, multiple passes10 lb-ft14 Nm
- Camshaft Position Sensor7 lb-ft10 Nm
- Electrical Connector Bolts5 lb-ft7 Nm
- Gasket Surface BoltsClean mating surfaces14 lb-ft19 Nm
- Intake Manifold Bolt18 lb-ft25 Nm
- Rocker Arm BoltsTighten with cam lobe pointing away22 lb-ft30 Nm
- Rocker Arm Shaft BoltsTighten evenly in sequence18 lb-ft25 Nm
- Sensor Mounting Bolts8 lb-ft11 Nm
- Valve Cover BoltsTighten in sequence7 lb-ft10 Nm
Long Block Replacement16 specs
- Camshaft Cap BoltsTighten in sequence from center outward, multiple passes10 lb-ft14 Nm
- Connecting Rod BoltsTTY - critical torque plus angle33 lb-ft45 Nm
- Cylinder Head BoltsTTY - tighten in sequence plus angle48 lb-ft65 Nm
- Electrical Connector Bolts5 lb-ft7 Nm
- Exhaust Manifold NutsApply anti-seize, work hot-to-cold22 lb-ft30 Nm
- Flywheel BoltsOften TTY, tighten in star pattern70 lb-ft95 Nm
- Gasket Surface BoltsClean mating surfaces14 lb-ft19 Nm
- Intake Manifold Bolt18 lb-ft25 Nm
- Main Bearing Cap BoltsTTY - tighten in sequence plus angle55 lb-ft75 Nm
- Oil Drain PlugUse new crush washer26 lb-ft35 Nm
- Oil Pan Bolt9 lb-ft12 Nm
- Sensor Mounting Bolts8 lb-ft11 Nm
- Timing Chain Tensioner BoltInstall with pin/clip to compress18 lb-ft25 Nm
- Timing Cover Bolts - 8mmTighten in sequence18 lb-ft25 Nm
- Transmission-to-Engine Bolts41 lb-ft55 Nm
- Valve Cover BoltsTighten in sequence7 lb-ft10 Nm
Main Bearings9 specs
- Electrical Connector Bolts5 lb-ft7 Nm
- Flywheel BoltsOften TTY, tighten in star pattern. Verify sequence with the service manual70 lb-ft95 Nm
- Gasket Surface BoltsClean mating surfaces14 lb-ft19 Nm
- Main Bearing Cap BoltsTTY - tighten in sequence plus angle. Verify sequence with the service manual55 lb-ft75 Nm
- Oil Drain PlugUse new crush washer. Verify sequence with the service manual26 lb-ft35 Nm
- Oil Pan BoltTighten in sequence. Verify sequence with the service manual9 lb-ft12 Nm
- Oil Pump Pickup TubeVerify sequence with the service manual9 lb-ft12 Nm
- Sensor Mounting Bolts8 lb-ft11 Nm
- Transmission-to-Engine BoltsVerify sequence with the service manual41 lb-ft55 Nm
Manifold Absolute Pressure Sensor4 specs
- Electrical Connector Bolts5 lb-ft7 Nm
- Gasket Surface BoltsClean mating surfaces14 lb-ft19 Nm
- MAP Sensor Screws2 lb-ft3 Nm
- Sensor Mounting Bolts8 lb-ft11 Nm
Mass Air Flow Sensor5 specs
- Air Intake Clamps2 lb-ft3 Nm
- Electrical Connector Bolts5 lb-ft7 Nm
- Gasket Surface BoltsClean mating surfaces14 lb-ft19 Nm
- MAF Sensor Screws2 lb-ft3 Nm
- Sensor Mounting Bolts8 lb-ft11 Nm
Oil Change2 specs
- Oil Drain PlugUse new crush washer30 lb-ft40 Nm
- Oil Filter (Spin-On)Hand tight plus 3/4 turn12 lb-ft16 Nm
Oil Level Sensor5 specs
- Electrical Connector Bolts5 lb-ft7 Nm
- Gasket Surface BoltsClean mating surfaces14 lb-ft19 Nm
- Oil Level Sensor11 lb-ft15 Nm
- Oil Pan BoltIf access needed9 lb-ft12 Nm
- Sensor Mounting Bolts8 lb-ft11 Nm
Oil Pan Gasket2 specs
- Oil Drain PlugUse new crush washer26 lb-ft35 Nm
- Oil Pan BoltTighten in sequence from center outward9 lb-ft12 Nm
Oil Pan Replacement6 specs
- Electrical Connector Bolts5 lb-ft7 Nm
- Gasket Surface BoltsClean mating surfaces14 lb-ft19 Nm
- Oil Drain PlugUse new crush washer26 lb-ft35 Nm
- Oil Pan BoltTighten in sequence9 lb-ft12 Nm
- Oil Pump Pickup Tube9 lb-ft12 Nm
- Sensor Mounting Bolts8 lb-ft11 Nm
Oil Pressure Sensor4 specs
- Electrical Connector Bolts5 lb-ft7 Nm
- Gasket Surface BoltsClean mating surfaces14 lb-ft19 Nm
- Oil Pressure SensorUse thread sealant15 lb-ft20 Nm
- Sensor Mounting Bolts8 lb-ft11 Nm
Oil Pump8 specs
- Electrical Connector Bolts5 lb-ft7 Nm
- Gasket Surface BoltsClean mating surfaces14 lb-ft19 Nm
- Oil Drain PlugUse new crush washer26 lb-ft35 Nm
- Oil Pan Bolt9 lb-ft12 Nm
- Oil Pump Bolts9 lb-ft12 Nm
- Oil Pump Pickup Tube9 lb-ft12 Nm
- Sensor Mounting Bolts8 lb-ft11 Nm
- Timing Cover Bolts - 8mmTighten in sequence18 lb-ft25 Nm
PCV Valve4 specs
- Electrical Connector Bolts5 lb-ft7 Nm
- Gasket Surface BoltsClean mating surfaces14 lb-ft19 Nm
- PCV ValveHand tight usually6 lb-ft8 Nm
- Sensor Mounting Bolts8 lb-ft11 Nm
Piston - Single7 specs
- Connecting Rod BoltsTTY - critical torque plus angle33 lb-ft45 Nm
- Cylinder Head BoltsTTY - tighten in sequence plus angle48 lb-ft65 Nm
- Electrical Connector Bolts5 lb-ft7 Nm
- Gasket Surface BoltsClean mating surfaces14 lb-ft19 Nm
- Oil Drain PlugUse new crush washer26 lb-ft35 Nm
- Oil Pan Bolt9 lb-ft12 Nm
- Sensor Mounting Bolts8 lb-ft11 Nm
Piston Rings - All9 specs
- Connecting Rod BoltsTTY - critical torque plus angle33 lb-ft45 Nm
- Cylinder Head BoltsTTY - tighten in sequence plus angle48 lb-ft65 Nm
- Electrical Connector Bolts5 lb-ft7 Nm
- Gasket Surface BoltsClean mating surfaces14 lb-ft19 Nm
- Main Bearing Cap BoltsTTY - tighten in sequence plus angle55 lb-ft75 Nm
- Oil Drain PlugUse new crush washer26 lb-ft35 Nm
- Oil Pan BoltTighten in sequence9 lb-ft12 Nm
- Oil Pump Pickup Tube9 lb-ft12 Nm
- Sensor Mounting Bolts8 lb-ft11 Nm
Pistons - All9 specs
- Connecting Rod BoltsTTY - critical torque plus angle33 lb-ft45 Nm
- Cylinder Head BoltsTTY - tighten in sequence plus angle48 lb-ft65 Nm
- Electrical Connector Bolts5 lb-ft7 Nm
- Gasket Surface BoltsClean mating surfaces14 lb-ft19 Nm
- Main Bearing Cap BoltsTTY - tighten in sequence plus angle55 lb-ft75 Nm
- Oil Drain PlugUse new crush washer26 lb-ft35 Nm
- Oil Pan Bolt9 lb-ft12 Nm
- Oil Pump Pickup Tube9 lb-ft12 Nm
- Sensor Mounting Bolts8 lb-ft11 Nm
Rear Main Seal9 specs
- Electrical Connector Bolts5 lb-ft7 Nm
- Flexplate BoltsAutomatic transmissions63 lb-ft85 Nm
- Flywheel BoltsOften TTY, tighten in star pattern70 lb-ft95 Nm
- Gasket Surface BoltsClean mating surfaces14 lb-ft19 Nm
- Oil Drain PlugUse new crush washer26 lb-ft35 Nm
- Oil Pan BoltRear section9 lb-ft12 Nm
- Rear Main Seal Housing9 lb-ft12 Nm
- Sensor Mounting Bolts8 lb-ft11 Nm
- Transmission-to-Engine Bolts41 lb-ft55 Nm
Rocker Arms - All7 specs
- Electrical Connector Bolts5 lb-ft7 Nm
- Gasket Surface BoltsClean mating surfaces14 lb-ft19 Nm
- Intake Manifold BoltIf pushrods18 lb-ft25 Nm
- Rocker Arm BoltsTighten with cam lobe pointing away22 lb-ft30 Nm
- Rocker Arm Shaft BoltsTighten evenly in sequence18 lb-ft25 Nm
- Sensor Mounting Bolts8 lb-ft11 Nm
- Valve Cover BoltsTighten in sequence7 lb-ft10 Nm
Serpentine Belt2 specs
- Belt Tensioner Bolt41 lb-ft55 Nm
- Idler Pulley Bolt33 lb-ft45 Nm
Serpentine Belt Tensioner4 specs
- Belt Tensioner Bolt41 lb-ft55 Nm
- Electrical Connector Bolts5 lb-ft7 Nm
- Gasket Surface BoltsClean mating surfaces14 lb-ft19 Nm
- Sensor Mounting Bolts8 lb-ft11 Nm
Short Block Replacement12 specs
- Connecting Rod BoltsTTY - critical torque plus angle33 lb-ft45 Nm
- Crankshaft Pulley BoltOften TTY - check spec, may require impact133 lb-ft180 Nm
- Electrical Connector Bolts5 lb-ft7 Nm
- Flywheel BoltsOften TTY, tighten in star pattern70 lb-ft95 Nm
- Gasket Surface BoltsClean mating surfaces14 lb-ft19 Nm
- Main Bearing Cap BoltsTTY - tighten in sequence plus angle55 lb-ft75 Nm
- Oil Drain PlugUse new crush washer26 lb-ft35 Nm
- Oil Pan Bolt9 lb-ft12 Nm
- Oil Pump Bolts9 lb-ft12 Nm
- Sensor Mounting Bolts8 lb-ft11 Nm
- Timing Cover Bolts - 8mmTighten in sequence18 lb-ft25 Nm
- Transmission-to-Engine Bolts41 lb-ft55 Nm
Throttle Body2 specs
- Air Intake Hose Clamps2 lb-ft3 Nm
- Throttle Body Bolts7 lb-ft10 Nm
Throttle Position Sensor4 specs
- Electrical Connector Bolts5 lb-ft7 Nm
- Gasket Surface BoltsClean mating surfaces14 lb-ft19 Nm
- Sensor Mounting Bolts8 lb-ft11 Nm
- TPS Screws2 lb-ft3 Nm
Timing Belt5 specs
- Camshaft Sprocket Bolts59 lb-ft80 Nm
- Crankshaft Pulley BoltOften TTY - check specs133 lb-ft + 60°180 Nm
- Timing Belt Idler30 lb-ft40 Nm
- Timing Belt Tensioner26 lb-ft35 Nm
- Water Pump BoltsReplace with timing belt18 lb-ft25 Nm
Timing Belt Kit14 specs
- Camshaft Sprocket BoltsHold cam with wrench on hex59 lb-ft80 Nm
- Crankshaft Pulley BoltOften TTY - check spec, may require impact124 lb-ft168 Nm
- Electrical Connector Bolts5 lb-ft7 Nm
- Gasket Surface BoltsClean mating surfaces14 lb-ft19 Nm
- Idler Bolt29 lb-ft39 Nm
- Oil Drain PlugUse new crush washer26 lb-ft35 Nm
- Sensor Mounting Bolts8 lb-ft11 Nm
- Tensioner Bolt33 lb-ft45 Nm
- Timing Belt Idler Pulley30 lb-ft40 Nm
- Timing Belt Tensioner26 lb-ft35 Nm
- Timing Cover Bolt10 lb-ft13 Nm
- Timing Cover Bolts - 8mmTighten in sequence18 lb-ft25 Nm
- Valve Cover BoltsTighten in sequence7 lb-ft10 Nm
- Water Pump BoltsTighten in criss-cross pattern18 lb-ft25 Nm
Timing Belt Tensioner10 specs
- Camshaft Sprocket Bolts52 lb-ft71 Nm
- Crankshaft Pulley BoltUse holder124 lb-ft167 Nm
- Electrical Connector Bolts5 lb-ft7 Nm
- Gasket Surface BoltsClean mating surfaces14 lb-ft19 Nm
- Idler Bolt29 lb-ft39 Nm
- Sensor Mounting Bolts8 lb-ft11 Nm
- Tensioner Bolt33 lb-ft45 Nm
- Timing Belt Tensioner26 lb-ft35 Nm
- Timing Cover Bolt10 lb-ft13 Nm
- Timing Cover Bolts - 8mmTighten in sequence18 lb-ft25 Nm
Transmission Mount7 specs
- Crossmember Bolt70 lb-ft95 Nm
- Drain PlugUse new washer24 lb-ft33 Nm
- Fill Plug24 lb-ft33 Nm
- Flywheel BoltsOften TTY, tighten in star pattern70 lb-ft95 Nm
- Transmission Drain PlugUse new crush washer if equipped22 lb-ft30 Nm
- Transmission Mount Bolts48 lb-ft65 Nm
- Transmission Pan BoltsTighten in criss-cross pattern9 lb-ft12 Nm
Valve Adjustment6 specs
- Electrical Connector Bolts5 lb-ft7 Nm
- Gasket Surface BoltsClean mating surfaces14 lb-ft19 Nm
- Rocker Arm BoltsTighten with cam lobe pointing away22 lb-ft30 Nm
- Sensor Mounting Bolts8 lb-ft11 Nm
- Valve Cover BoltsTighten in sequence7 lb-ft10 Nm
- Valve Lash Adjusting Screw Lock NutHold screw while tightening15 lb-ft20 Nm
Valve Cover Gasket - Single2 specs
- Spark Plug Tube SealsIf equipped with separate seals9 lb-ft12 Nm
- Valve Cover BoltsTighten in sequence7 lb-ft10 Nm
Valve Cover Gaskets - Both7 specs
- Electrical Connector Bolts5 lb-ft7 Nm
- Gasket Surface BoltsClean mating surfaces14 lb-ft19 Nm
- Ignition Coil Bolt6 lb-ft8 Nm
- Intake Manifold BoltIf required18 lb-ft25 Nm
- Sensor Mounting Bolts8 lb-ft11 Nm
- Spark Plugs - Aluminum HeadApply anti-seize to threads15 lb-ft20 Nm
- Valve Cover BoltsTighten in sequence7 lb-ft10 Nm
Valve Job - Complete12 specs
- Camshaft Cap BoltsTighten in sequence from center outward, multiple passes10 lb-ft14 Nm
- Camshaft Sprocket BoltsHold cam with wrench on hex59 lb-ft80 Nm
- Cylinder Head BoltsTTY - tighten in sequence plus angle48 lb-ft65 Nm
- Electrical Connector Bolts5 lb-ft7 Nm
- Exhaust Manifold NutsApply anti-seize, work hot-to-cold22 lb-ft30 Nm
- Gasket Surface BoltsClean mating surfaces14 lb-ft19 Nm
- Intake Manifold Bolt18 lb-ft25 Nm
- Rocker Arm BoltsTighten with cam lobe pointing away22 lb-ft30 Nm
- Sensor Mounting Bolts8 lb-ft11 Nm
- Timing Chain Tensioner BoltInstall with pin/clip to compress18 lb-ft25 Nm
- Timing Cover Bolts - 8mmTighten in sequence18 lb-ft25 Nm
- Valve Cover BoltsTighten in sequence7 lb-ft10 Nm
Valve Seals8 specs
- Camshaft Cap BoltsTighten in sequence from center outward, multiple passes10 lb-ft14 Nm
- Electrical Connector Bolts5 lb-ft7 Nm
- Gasket Surface BoltsClean mating surfaces14 lb-ft19 Nm
- Rocker Arm BoltsTighten with cam lobe pointing away22 lb-ft30 Nm
- Rocker Arm Shaft BoltsTighten evenly in sequence18 lb-ft25 Nm
- Sensor Mounting Bolts8 lb-ft11 Nm
- Spark Plugs - Aluminum HeadApply anti-seize to threads15 lb-ft20 Nm
- Valve Cover BoltsTighten in sequence7 lb-ft10 Nm
Valve Spring - Single6 specs
- Electrical Connector Bolts5 lb-ft7 Nm
- Gasket Surface BoltsClean mating surfaces14 lb-ft19 Nm
- Rocker Arm BoltsTighten with cam lobe pointing away22 lb-ft30 Nm
- Sensor Mounting Bolts8 lb-ft11 Nm
- Spark Plugs - Aluminum HeadApply anti-seize to threads15 lb-ft20 Nm
- Valve Cover BoltsTighten in sequence7 lb-ft10 Nm
Valve Springs - All8 specs
- Camshaft Cap BoltsTighten in sequence from center outward, multiple passes10 lb-ft14 Nm
- Electrical Connector Bolts5 lb-ft7 Nm
- Gasket Surface BoltsClean mating surfaces14 lb-ft19 Nm
- Rocker Arm BoltsTighten with cam lobe pointing away22 lb-ft30 Nm
- Rocker Arm Shaft BoltsTighten evenly in sequence18 lb-ft25 Nm
- Sensor Mounting Bolts8 lb-ft11 Nm
- Spark Plugs - Aluminum HeadApply anti-seize to threads15 lb-ft20 Nm
- Valve Cover BoltsTighten in sequence7 lb-ft10 Nm
Variable Valve Timing Actuator10 specs
- Cam Phaser BoltApply threadlocker, hold cam stationary48 lb-ft65 Nm
- Camshaft Sprocket BoltsHold cam with wrench on hex59 lb-ft80 Nm
- Crankshaft Pulley BoltOften TTY - check spec, may require impact133 lb-ft180 Nm
- Electrical Connector Bolts5 lb-ft7 Nm
- Gasket Surface BoltsClean mating surfaces14 lb-ft19 Nm
- Sensor Mounting Bolts8 lb-ft11 Nm
- Timing Chain Tensioner BoltInstall with pin/clip to compress18 lb-ft25 Nm
- Timing Cover Bolts - 8mmTighten in sequence18 lb-ft25 Nm
- Valve Cover BoltsTighten in sequence7 lb-ft10 Nm
- VVT Solenoid Bolt7 lb-ft10 Nm
VVT Solenoid - Single5 specs
- Electrical Connector Bolts5 lb-ft7 Nm
- Gasket Surface BoltsClean mating surfaces14 lb-ft19 Nm
- Sensor Mounting Bolts8 lb-ft11 Nm
- Valve Cover BoltsTighten in sequence7 lb-ft10 Nm
- VVT Solenoid Bolt7 lb-ft10 Nm
VVT Solenoids - All6 specs
- Camshaft Position Sensor7 lb-ft10 Nm
- Electrical Connector Bolts5 lb-ft7 Nm
- Gasket Surface BoltsClean mating surfaces14 lb-ft19 Nm
- Sensor Mounting Bolts8 lb-ft11 Nm
- Valve Cover BoltsTighten in sequence7 lb-ft10 Nm
- VVT Solenoid Bolt7 lb-ft10 Nm

Cooling

Coolant Bypass Pipe8 specs
- Bleed ScrewOpen during fill5 lb-ft6 Nm
- Coolant Drain Plug11 lb-ft15 Nm
- Drain PetcockHand tight5 lb-ft7 Nm
- Fan Bolts8 lb-ft11 Nm
- Hose Clamps2 lb-ft3 Nm
- Pump BoltsTorque in sequence17 lb-ft23 Nm
- Thermostat Housing Bolt11 lb-ft15 Nm
- Water Pump BoltsTighten in criss-cross pattern18 lb-ft25 Nm
Coolant Flush12 specs
- Air Box Clips4 lb-ft5 Nm
- Bleed ScrewOpen during fill5 lb-ft7 Nm
- Block Drain PlugIf equipped, use new washer18 lb-ft25 Nm
- Connector Bolts5 lb-ft7 Nm
- Coolant Hose Clamps3 lb-ft4 Nm
- Drain Petcock4 lb-ft5 Nm
- Drain Plug11 lb-ft15 Nm
- Hose Clamps3 lb-ft4 Nm
- Oil Drain PlugUse new crush washer26 lb-ft35 Nm
- Pump Bolts17 lb-ft23 Nm
- Radiator CapHand tight1 lb-ft1 Nm
- Wheel Lug NutsTorque in star pattern65 lb-ft88 Nm
Coolant Reservoir9 specs
- Bleed ScrewOpen during fill5 lb-ft6 Nm
- Coolant Drain Plug11 lb-ft15 Nm
- Drain PetcockHand tight5 lb-ft7 Nm
- Fan Bolts8 lb-ft11 Nm
- Hose ClampsDo not overtighten3 lb-ft4 Nm
- Pump BoltsTorque in sequence17 lb-ft23 Nm
- Reservoir Mounting Bolts6 lb-ft8 Nm
- Thermostat Housing Bolt10 lb-ft14 Nm
- Water Pump BoltsTighten in criss-cross pattern18 lb-ft25 Nm
Coolant Temperature Sensor8 specs
- Bleed ScrewOpen during fill5 lb-ft6 Nm
- Coolant Drain Plug11 lb-ft15 Nm
- Drain PetcockHand tight5 lb-ft7 Nm
- Fan Bolts8 lb-ft11 Nm
- Hose Clamps2 lb-ft3 Nm
- Pump BoltsTorque in sequence17 lb-ft23 Nm
- Thermostat Housing Bolt11 lb-ft15 Nm
- Water Pump BoltsTighten in criss-cross pattern18 lb-ft25 Nm
Cooling Fan Assembly7 specs
- Coolant Drain Plug11 lb-ft15 Nm
- Drain PetcockHand tight5 lb-ft7 Nm
- Fan Bolts8 lb-ft11 Nm
- Hose Clamps2 lb-ft3 Nm
- Pump BoltsTorque in sequence17 lb-ft23 Nm
- Thermostat Housing Bolt11 lb-ft15 Nm
- Water Pump BoltsTighten in criss-cross pattern18 lb-ft25 Nm
Cooling Fan Clutch7 specs
- Coolant Drain Plug11 lb-ft15 Nm
- Drain PetcockHand tight5 lb-ft7 Nm
- Fan Bolts8 lb-ft11 Nm
- Hose Clamps2 lb-ft3 Nm
- Pump BoltsTorque in sequence17 lb-ft23 Nm
- Thermostat Housing Bolt11 lb-ft15 Nm
- Water Pump BoltsTighten in criss-cross pattern18 lb-ft25 Nm
Cooling Fan Motor7 specs
- Drain PetcockHand tight5 lb-ft7 Nm
- Electrical Connector4 lb-ft5 Nm
- Fan Bolts8 lb-ft11 Nm
- Fan Motor Bolts6 lb-ft8 Nm
- Hose ClampsDo not overtighten3 lb-ft4 Nm
- Pump BoltsTorque in sequence17 lb-ft23 Nm
- Thermostat Housing Bolt10 lb-ft14 Nm
Cooling Fan Relay7 specs
- Coolant Drain Plug11 lb-ft15 Nm
- Drain PetcockHand tight5 lb-ft7 Nm
- Fan Bolts8 lb-ft11 Nm
- Hose Clamps2 lb-ft3 Nm
- Pump BoltsTorque in sequence17 lb-ft23 Nm
- Thermostat Housing Bolt11 lb-ft15 Nm
- Water Pump BoltsTighten in criss-cross pattern18 lb-ft25 Nm
Heater Control Valve6 specs
- Drain PetcockHand tight5 lb-ft7 Nm
- Fan Bolts8 lb-ft11 Nm
- Hose Clamps2 lb-ft3 Nm
- Pump BoltsTorque in sequence17 lb-ft23 Nm
- Thermostat Housing Bolt10 lb-ft14 Nm
- Valve Mounting6 lb-ft8 Nm
Heater Core8 specs
- Dashboard Screws2 lb-ft3 Nm
- Drain PetcockHand tight5 lb-ft7 Nm
- Fan Bolts8 lb-ft11 Nm
- Heater Core Mounting6 lb-ft8 Nm
- Heater Hose Clamps2 lb-ft3 Nm
- Hose ClampsDo not overtighten3 lb-ft4 Nm
- Pump BoltsTorque in sequence17 lb-ft23 Nm
- Thermostat Housing Bolt10 lb-ft14 Nm
Heater Hoses7 specs
- Coolant Drain Plug11 lb-ft15 Nm
- Drain PetcockHand tight5 lb-ft7 Nm
- Fan Bolts8 lb-ft11 Nm
- Hose Clamps2 lb-ft3 Nm
- Pump BoltsTorque in sequence17 lb-ft23 Nm
- Thermostat Housing Bolt11 lb-ft15 Nm
- Water Pump BoltsTighten in criss-cross pattern18 lb-ft25 Nm
Radiator4 specs
- Drain PetcockPlastic - hand tight4 lb-ft5 Nm
- Radiator Mounting BoltDo not overtighten plastic mounts9 lb-ft12 Nm
- Transmission Cooler LinesIf equipped18 lb-ft25 Nm
- Upper/Lower Hose Clamps2 lb-ft3 Nm
Radiator Cap7 specs
- Coolant Drain Plug11 lb-ft15 Nm
- Drain PetcockHand tight5 lb-ft7 Nm
- Fan Bolts8 lb-ft11 Nm
- Hose Clamps2 lb-ft3 Nm
- Pump BoltsTorque in sequence17 lb-ft23 Nm
- Thermostat Housing Bolt11 lb-ft15 Nm
- Water Pump BoltsTighten in criss-cross pattern18 lb-ft25 Nm
Radiator Hose - Lower5 specs
- Drain PetcockHand tight5 lb-ft7 Nm
- Fan Bolts8 lb-ft11 Nm
- Hose Clamps2 lb-ft3 Nm
- Pump BoltsTorque in sequence17 lb-ft23 Nm
- Thermostat Housing Bolt10 lb-ft14 Nm
Radiator Hose - Upper5 specs
- Drain PetcockHand tight5 lb-ft7 Nm
- Fan Bolts8 lb-ft11 Nm
- Hose Clamps2 lb-ft3 Nm
- Pump BoltsTorque in sequence17 lb-ft23 Nm
- Thermostat Housing Bolt10 lb-ft14 Nm
Radiator Hoses - Both7 specs
- Coolant Drain Plug11 lb-ft15 Nm
- Drain PetcockHand tight5 lb-ft7 Nm
- Fan Bolts8 lb-ft11 Nm
- Hose Clamps2 lb-ft3 Nm
- Pump BoltsTorque in sequence17 lb-ft23 Nm
- Thermostat Housing Bolt11 lb-ft15 Nm
- Water Pump BoltsTighten in criss-cross pattern18 lb-ft25 Nm
Radiator Removal and Service4 specs
- Drain PetcockPlastic - hand-tight only4 lb-ft5 Nm
- Fan Shroud Bolts7 lb-ft10 Nm
- Radiator Mounting BoltDo not overtighten plastic mounts9 lb-ft12 Nm
- Transmission Cooler LinesIf equipped, use new washers18 lb-ft25 Nm
Thermostat2 specs
- Coolant Temperature SensorUse thread sealant15 lb-ft20 Nm
- Thermostat Housing Bolt11 lb-ft15 Nm
Thermostat Housing8 specs
- Coolant Drain Plug11 lb-ft15 Nm
- Coolant Hose Clamps3 lb-ft4 Nm
- Drain PetcockHand tight5 lb-ft7 Nm
- Fan Bolts8 lb-ft11 Nm
- Hose Clamps2 lb-ft3 Nm
- Pump BoltsTorque in sequence17 lb-ft23 Nm
- Thermostat Housing Bolt11 lb-ft15 Nm
- Water Pump BoltsTighten in criss-cross pattern18 lb-ft25 Nm
Water Pump3 specs
- Hose ClampsSpring clamps preferred2 lb-ft3 Nm
- Thermostat Housing Bolt11 lb-ft15 Nm
- Water Pump BoltsTighten in criss-cross pattern18 lb-ft25 Nm

Ignition

Coil Pack3 specs
- Connector Bolts5 lb-ft7 Nm
- Ignition Coil Bolt6 lb-ft8 Nm
- Spark Plugs - Aluminum HeadApply anti-seize to threads15 lb-ft20 Nm
Ignition Coil - Single3 specs
- Connector Bolts5 lb-ft7 Nm
- Ignition Coil Bolt6 lb-ft8 Nm
- Spark Plugs - Aluminum HeadApply anti-seize to threads15 lb-ft20 Nm
Ignition Coils - All3 specs
- Connector Bolts5 lb-ft7 Nm
- Ignition Coil Bolt6 lb-ft8 Nm
- Spark Plugs - Aluminum HeadApply anti-seize to threads15 lb-ft20 Nm
Ignition Control Module3 specs
- Connector Bolts5 lb-ft7 Nm
- Ignition Coil Bolt6 lb-ft8 Nm
- Spark Plugs - Aluminum HeadApply anti-seize to threads15 lb-ft20 Nm
Ignition Lock Cylinder3 specs
- Connector Bolts5 lb-ft7 Nm
- Ignition Coil Bolt6 lb-ft8 Nm
- Spark Plugs - Aluminum HeadApply anti-seize to threads15 lb-ft20 Nm
Ignition Switch3 specs
- Connector Bolts5 lb-ft7 Nm
- Steering Column Bolts22 lb-ft30 Nm
- Switch Mounting Screws4 lb-ft5 Nm
Spark Plug Wires5 specs
- Connector Bolts5 lb-ft7 Nm
- Engine Cover Clips2 lb-ft3 Nm
- Ignition Coil Bolt6 lb-ft8 Nm
- Spark PlugGap before install14 lb-ft19 Nm
- Spark Plugs - Aluminum HeadApply anti-seize to threads15 lb-ft20 Nm
Spark Plugs8 specs
- Air Box Clips4 lb-ft5 Nm
- Connector Bolts5 lb-ft7 Nm
- Engine Cover Clips2 lb-ft3 Nm
- Ignition Coil Bolt6 lb-ft8 Nm
- Oil Drain PlugUse new crush washer26 lb-ft35 Nm
- Spark PlugGap before install14 lb-ft19 Nm
- Spark Plugs - Aluminum HeadApply anti-seize to threads15 lb-ft20 Nm
- Wheel Lug NutsTorque in star pattern65 lb-ft88 Nm

Fuel system

Charcoal Canister6 specs
- Filter Bracket8 lb-ft11 Nm
- Fuel Line FittingsUse new O-rings18 lb-ft25 Nm
- Fuel Rail Bolts9 lb-ft12 Nm
- Hose Clamps2 lb-ft3 Nm
- Pressure Regulator Screws5 lb-ft7 Nm
- Pump Mounting10 lb-ft14 Nm
EVAP Purge Valve6 specs
- Filter Bracket8 lb-ft11 Nm
- Fuel Line FittingsUse new O-rings18 lb-ft25 Nm
- Fuel Rail Bolts9 lb-ft12 Nm
- Hose Clamps2 lb-ft3 Nm
- Pressure Regulator Screws5 lb-ft7 Nm
- Pump Mounting10 lb-ft14 Nm
EVAP Vent Valve6 specs
- Filter Bracket8 lb-ft11 Nm
- Fuel Line FittingsUse new O-rings18 lb-ft25 Nm
- Fuel Rail Bolts9 lb-ft12 Nm
- Hose Clamps2 lb-ft3 Nm
- Pressure Regulator Screws5 lb-ft7 Nm
- Pump Mounting10 lb-ft14 Nm
Fuel Cap6 specs
- Filter Bracket8 lb-ft11 Nm
- Fuel Line FittingsUse new O-rings18 lb-ft25 Nm
- Fuel Rail Bolts9 lb-ft12 Nm
- Hose Clamps2 lb-ft3 Nm
- Pressure Regulator Screws5 lb-ft7 Nm
- Pump Mounting10 lb-ft14 Nm
Fuel Filler Neck6 specs
- Filler Neck Bolts7 lb-ft10 Nm
- Filter Bracket8 lb-ft11 Nm
- Fuel Rail Bolts14 lb-ft19 Nm
- Hose Clamps2 lb-ft3 Nm
- Pressure Regulator Screws5 lb-ft7 Nm
- Pump Mounting10 lb-ft14 Nm
Fuel Filter7 specs
- Air Box Clips4 lb-ft5 Nm
- Connector Bolts5 lb-ft7 Nm
- Filter Bracket Bolt9.6 lb-ft13 Nm
- Fuel Filter Bracket Bolt7 lb-ft10 Nm
- Fuel Line FittingsIf threaded type18 lb-ft25 Nm
- Oil Drain PlugUse new crush washer26 lb-ft35 Nm
- Wheel Lug NutsTorque in star pattern65 lb-ft88 Nm
Fuel Filter - In-Tank7 specs
- Filter Bracket8 lb-ft11 Nm
- Filter Bracket Bolt10 lb-ft13 Nm
- Fuel Line FittingsUse new O-rings18 lb-ft25 Nm
- Fuel Rail Bolts9 lb-ft12 Nm
- Hose Clamps2 lb-ft3 Nm
- Pressure Regulator Screws5 lb-ft7 Nm
- Pump Mounting10 lb-ft14 Nm
Fuel Injector - Single6 specs
- Filter Bracket8 lb-ft11 Nm
- Fuel Line FittingsUse new O-rings18 lb-ft25 Nm
- Fuel Rail Bolts9 lb-ft12 Nm
- Hose Clamps2 lb-ft3 Nm
- Pressure Regulator Screws5 lb-ft7 Nm
- Pump Mounting10 lb-ft14 Nm
Fuel Injector Cleaning6 specs
- Filter Bracket8 lb-ft11 Nm
- Fuel Line FittingsUse new O-rings18 lb-ft25 Nm
- Fuel Rail Bolts9 lb-ft12 Nm
- Hose Clamps2 lb-ft3 Nm
- Pressure Regulator Screws5 lb-ft7 Nm
- Pump Mounting10 lb-ft14 Nm
Fuel Injectors - All6 specs
- Filter Bracket8 lb-ft11 Nm
- Fuel Line FittingsUse new O-rings18 lb-ft25 Nm
- Fuel Rail Bolts9 lb-ft12 Nm
- Hose Clamps2 lb-ft3 Nm
- Pressure Regulator Screws5 lb-ft7 Nm
- Pump Mounting10 lb-ft14 Nm
Fuel Level Sensor6 specs
- Filter Bracket8 lb-ft11 Nm
- Fuel Line FittingsUse new O-rings18 lb-ft25 Nm
- Fuel Rail Bolts9 lb-ft12 Nm
- Hose Clamps2 lb-ft3 Nm
- Pressure Regulator Screws5 lb-ft7 Nm
- Pump Mounting10 lb-ft14 Nm
Fuel Line - High Pressure6 specs
- Filter Bracket8 lb-ft11 Nm
- Fuel Line FittingsUse new O-rings18 lb-ft25 Nm
- Fuel Rail Bolts9 lb-ft12 Nm
- Hose Clamps2 lb-ft3 Nm
- Pressure Regulator Screws5 lb-ft7 Nm
- Pump Mounting10 lb-ft14 Nm
Fuel Line - Return6 specs
- Filter Bracket8 lb-ft11 Nm
- Fuel Line FittingsUse new O-rings18 lb-ft25 Nm
- Fuel Rail Bolts9 lb-ft12 Nm
- Hose Clamps2 lb-ft3 Nm
- Pressure Regulator Screws5 lb-ft7 Nm
- Pump Mounting10 lb-ft14 Nm
Fuel Pressure Regulator6 specs
- Filter Bracket8 lb-ft11 Nm
- Fuel Line18 lb-ft25 Nm
- Fuel Rail Bolts14 lb-ft19 Nm
- Pressure Regulator Screws5 lb-ft7 Nm
- Pump Mounting10 lb-ft14 Nm
- Regulator Mounting Screws4 lb-ft5 Nm
Fuel Pump2 specs
- Fuel Pump Module Lock RingUse special tool59 lb-ft80 Nm
- Tank Strap Bolts26 lb-ft35 Nm
Fuel Pump Module8 specs
- Access Cover Screws3 lb-ft4 Nm
- Filter Bracket8 lb-ft11 Nm
- Fuel Line FittingsUse new O-rings18 lb-ft25 Nm
- Fuel Pump Lock RingLock ring tool48 lb-ft64 Nm
- Fuel Rail Bolts9 lb-ft12 Nm
- Hose Clamps2 lb-ft3 Nm
- Pressure Regulator Screws5 lb-ft7 Nm
- Pump Mounting10 lb-ft14 Nm
Fuel Rail6 specs
- Filter Bracket8 lb-ft11 Nm
- Fuel Line FittingsUse new O-rings18 lb-ft25 Nm
- Fuel Rail Bolts9 lb-ft12 Nm
- Hose Clamps2 lb-ft3 Nm
- Pressure Regulator Screws5 lb-ft7 Nm
- Pump Mounting10 lb-ft14 Nm
Fuel Tank7 specs
- Filler Neck Clamp3 lb-ft4 Nm
- Filter Bracket8 lb-ft11 Nm
- Fuel Line FittingsUse new O-rings18 lb-ft25 Nm
- Fuel Rail Bolts14 lb-ft19 Nm
- Pressure Regulator Screws5 lb-ft7 Nm
- Pump Mounting10 lb-ft14 Nm
- Tank Strap Bolts26 lb-ft35 Nm
Fuel Tank Strap6 specs
- Filter Bracket8 lb-ft11 Nm
- Fuel Line FittingsUse new O-rings18 lb-ft25 Nm
- Fuel Rail Bolts9 lb-ft12 Nm
- Hose Clamps2 lb-ft3 Nm
- Pressure Regulator Screws5 lb-ft7 Nm
- Pump Mounting10 lb-ft14 Nm
High Pressure Fuel Pump6 specs
- Filter Bracket8 lb-ft11 Nm
- Fuel Line FittingsUse new O-rings18 lb-ft25 Nm
- Fuel Rail Bolts9 lb-ft12 Nm
- Hose Clamps2 lb-ft3 Nm
- Pressure Regulator Screws5 lb-ft7 Nm
- Pump Mounting10 lb-ft14 Nm

Electrical

Airbag - Driver5 specs
- Airbag Module BoltsTorx - disconnect battery and wait 2 minutes5 lb-ft7 Nm
- Battery Terminal Bolts5 lb-ft7 Nm
- Connector Screws3 lb-ft4 Nm
- Ground Strap BoltsClean contact surfaces10 lb-ft14 Nm
- Steering Wheel Nut40 lb-ft54 Nm
Airbag - Passenger5 specs
- Airbag Module BoltsTorx - disconnect battery and wait 2 minutes5 lb-ft7 Nm
- Battery Terminal Bolts5 lb-ft7 Nm
- Connector Screws3 lb-ft4 Nm
- Dashboard Fasteners3 lb-ft4 Nm
- Ground Strap BoltsClean contact surfaces10 lb-ft14 Nm
Airbag - Side5 specs
- Battery Terminal Bolts5 lb-ft7 Nm
- Connector Screws3 lb-ft4 Nm
- Ground Strap BoltsClean contact surfaces10 lb-ft14 Nm
- Seat Mounting BoltsSafety critical45 lb-ft61 Nm
- Side Airbag Module BoltsTorx5 lb-ft7 Nm
Airbag Module/Computer5 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
- Ground Strap BoltsEnsure clean contact9 lb-ft12 Nm
- Module Mounting Bolts6 lb-ft8 Nm
- Sensor Mounting Bolts7 lb-ft10 Nm
Alternator4 specs
- Alternator Mounting Bolts37 lb-ft50 Nm
- Alternator Pivot Bolt18 lb-ft25 Nm
- Battery Terminal BoltsDo not overtighten6 lb-ft8 Nm
- Serpentine Belt Tensioner41 lb-ft55 Nm
Alternator Belt8 specs
- Alternator Mounting Bolts33 lb-ft45 Nm
- Alternator Pivot Bolt33 lb-ft45 Nm
- Battery Cable Nut10 lb-ft13 Nm
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
- Ground Strap BoltsEnsure clean contact9 lb-ft12 Nm
- Module Mounting Bolts6 lb-ft8 Nm
- Sensor Mounting Bolts7 lb-ft10 Nm
Amplifier5 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
- Ground Strap BoltsEnsure clean contact9 lb-ft12 Nm
- Module Mounting Bolts6 lb-ft8 Nm
- Sensor Mounting Bolts7 lb-ft10 Nm
Antenna5 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
- Ground Strap BoltsEnsure clean contact9 lb-ft12 Nm
- Module Mounting Bolts6 lb-ft8 Nm
- Sensor Mounting Bolts7 lb-ft10 Nm
Backup Camera5 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
- Ground Strap BoltsEnsure clean contact9 lb-ft12 Nm
- Module Mounting Bolts6 lb-ft8 Nm
- Sensor Mounting Bolts7 lb-ft10 Nm
Battery3 specs
- Battery Hold-Down Bolt6 lb-ft8 Nm
- Battery Terminal BoltsDo not overtighten - can crack terminal4 lb-ft6 Nm
- Battery Tray Bolts9 lb-ft12 Nm
Battery Cable - Negative7 specs
- Battery Hold-Down BoltDo not overtighten8 lb-ft11 Nm
- Battery Terminal BoltsDo not overtighten5 lb-ft7 Nm
- Connector Screws3 lb-ft4 Nm
- Ground Cable Bolt10 lb-ft13 Nm
- Ground Strap BoltsEnsure clean contact9 lb-ft12 Nm
- Module Mounting Bolts6 lb-ft8 Nm
- Sensor Mounting Bolts7 lb-ft10 Nm
Battery Cable - Positive7 specs
- Battery Hold-Down BoltDo not overtighten8 lb-ft10 Nm
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
- Ground Cable Bolt10 lb-ft13 Nm
- Ground Strap BoltsEnsure clean contact9 lb-ft12 Nm
- Module Mounting Bolts6 lb-ft8 Nm
- Sensor Mounting Bolts7 lb-ft10 Nm
Battery Cables - Both7 specs
- Battery Hold-Down BoltDo not overtighten8 lb-ft10 Nm
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
- Ground Cable Bolt10 lb-ft13 Nm
- Ground Strap BoltsEnsure clean contact9 lb-ft12 Nm
- Module Mounting Bolts6 lb-ft8 Nm
- Sensor Mounting Bolts7 lb-ft10 Nm
Battery Terminal7 specs
- Battery Hold-Down BoltDo not overtighten8 lb-ft10 Nm
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
- Ground Cable Bolt10 lb-ft13 Nm
- Ground Strap BoltsEnsure clean contact9 lb-ft12 Nm
- Module Mounting Bolts6 lb-ft8 Nm
- Sensor Mounting Bolts7 lb-ft10 Nm
Blower Motor2 specs
- Blower Motor Mounting Screw3 lb-ft4 Nm
- Blower Motor Resistor Screws1.5 lb-ft2 Nm
Blower Motor Control Module5 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
- Ground Strap BoltsEnsure clean contact9 lb-ft12 Nm
- Module Mounting Bolts6 lb-ft8 Nm
- Sensor Mounting Bolts7 lb-ft10 Nm
Blower Motor Resistor4 specs
- Battery Terminal Bolts5 lb-ft7 Nm
- Connector Screws3 lb-ft4 Nm
- Ground Strap BoltsClean contact surfaces10 lb-ft14 Nm
- Resistor Screws1.5 lb-ft2 Nm
Clock Spring7 specs
- Airbag Module BoltsTorx - disconnect battery first5 lb-ft7 Nm
- Battery Terminal Bolts5 lb-ft7 Nm
- Clock Spring ScrewsAlign marks before removal3 lb-ft4 Nm
- Connector Screws3 lb-ft4 Nm
- Ground Strap BoltsClean contact surfaces10 lb-ft14 Nm
- Steering Column CoversPlastic clips2 lb-ft3 Nm
- Steering Wheel Nut40 lb-ft54 Nm
Combination Switch5 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
- Ground Strap BoltsEnsure clean contact9 lb-ft12 Nm
- Module Mounting Bolts6 lb-ft8 Nm
- Sensor Mounting Bolts7 lb-ft10 Nm
Dimmer Switch5 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
- Ground Strap BoltsEnsure clean contact9 lb-ft12 Nm
- Module Mounting Bolts6 lb-ft8 Nm
- Sensor Mounting Bolts7 lb-ft10 Nm
Door Lock Actuator - Front5 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
- Ground Strap BoltsEnsure clean contact9 lb-ft12 Nm
- Module Mounting Bolts6 lb-ft8 Nm
- Sensor Mounting Bolts7 lb-ft10 Nm
Door Lock Actuator - Rear5 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
- Ground Strap BoltsEnsure clean contact9 lb-ft12 Nm
- Module Mounting Bolts6 lb-ft8 Nm
- Sensor Mounting Bolts7 lb-ft10 Nm
Fog Light Assembly5 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
- Ground Strap BoltsEnsure clean contact9 lb-ft12 Nm
- Module Mounting Bolts6 lb-ft8 Nm
- Sensor Mounting Bolts7 lb-ft10 Nm
Fog Light Bulb5 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
- Ground Strap BoltsEnsure clean contact9 lb-ft12 Nm
- Module Mounting Bolts6 lb-ft8 Nm
- Sensor Mounting Bolts7 lb-ft10 Nm
Fuel Pump Relay6 specs
- Access Cover Screws3 lb-ft4 Nm
- Battery Terminal Bolts5 lb-ft7 Nm
- Connector Screws3 lb-ft4 Nm
- Fuel Pump Lock RingLock ring tool48 lb-ft64 Nm
- Ground Strap BoltsClean contact surfaces10 lb-ft14 Nm
- Relay Socket4 lb-ft5 Nm
Fuse Box - Engine Bay5 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
- Ground Strap BoltsEnsure clean contact9 lb-ft12 Nm
- Module Mounting Bolts6 lb-ft8 Nm
- Sensor Mounting Bolts7 lb-ft10 Nm
Fuse Box - Interior5 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
- Ground Strap BoltsEnsure clean contact9 lb-ft12 Nm
- Module Mounting Bolts6 lb-ft8 Nm
- Sensor Mounting Bolts7 lb-ft10 Nm
Headlight Assembly5 specs
- Adjuster Screws2 lb-ft3 Nm
- Battery Terminal Bolts5 lb-ft7 Nm
- Connector Screws3 lb-ft4 Nm
- Ground Strap BoltsClean contact surfaces10 lb-ft14 Nm
- Headlight Assembly Bolts7 lb-ft10 Nm
Headlight Bulb - Single4 specs
- Battery Terminal Bolts5 lb-ft7 Nm
- Bulb Retaining Ring4 lb-ft5 Nm
- Connector Screws3 lb-ft4 Nm
- Ground Strap BoltsClean contact surfaces10 lb-ft14 Nm
Headlight Bulbs - Pair5 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
- Ground Strap BoltsEnsure clean contact9 lb-ft12 Nm
- Module Mounting Bolts6 lb-ft8 Nm
- Sensor Mounting Bolts7 lb-ft10 Nm
Headlight Switch5 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
- Ground Strap BoltsEnsure clean contact9 lb-ft12 Nm
- Module Mounting Bolts6 lb-ft8 Nm
- Sensor Mounting Bolts7 lb-ft10 Nm
Heated Seat Module5 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
- Ground Strap BoltsEnsure clean contact9 lb-ft12 Nm
- Module Mounting Bolts6 lb-ft8 Nm
- Sensor Mounting Bolts7 lb-ft10 Nm
HID Ballast5 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
- Ground Strap BoltsEnsure clean contact9 lb-ft12 Nm
- Module Mounting Bolts6 lb-ft8 Nm
- Sensor Mounting Bolts7 lb-ft10 Nm
Horn4 specs
- Battery Terminal Bolts5 lb-ft7 Nm
- Connector Screws3 lb-ft4 Nm
- Ground Strap BoltsClean contact surfaces10 lb-ft14 Nm
- Horn Mounting Bolt11 lb-ft15 Nm
Horn Relay5 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
- Ground Strap BoltsEnsure clean contact9 lb-ft12 Nm
- Module Mounting Bolts6 lb-ft8 Nm
- Sensor Mounting Bolts7 lb-ft10 Nm
Instrument Cluster5 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
- Ground Strap BoltsEnsure clean contact9 lb-ft12 Nm
- Module Mounting Bolts6 lb-ft8 Nm
- Sensor Mounting Bolts7 lb-ft10 Nm
LED Headlight Module5 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
- Ground Strap BoltsEnsure clean contact9 lb-ft12 Nm
- Module Mounting Bolts6 lb-ft8 Nm
- Sensor Mounting Bolts7 lb-ft10 Nm
Main Relay5 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
- Ground Strap BoltsEnsure clean contact9 lb-ft12 Nm
- Module Mounting Bolts6 lb-ft8 Nm
- Sensor Mounting Bolts7 lb-ft10 Nm
Power Antenna Motor5 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
- Ground Strap BoltsEnsure clean contact9 lb-ft12 Nm
- Module Mounting Bolts6 lb-ft8 Nm
- Sensor Mounting Bolts7 lb-ft10 Nm
Power Mirror Motor5 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
- Ground Strap BoltsEnsure clean contact9 lb-ft12 Nm
- Module Mounting Bolts6 lb-ft8 Nm
- Sensor Mounting Bolts7 lb-ft10 Nm
Power Seat Motor5 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
- Ground Strap BoltsEnsure clean contact9 lb-ft12 Nm
- Module Mounting Bolts6 lb-ft8 Nm
- Sensor Mounting Bolts7 lb-ft10 Nm
Power Window Motor - Front5 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
- Ground Strap BoltsEnsure clean contact9 lb-ft12 Nm
- Module Mounting Bolts6 lb-ft8 Nm
- Sensor Mounting Bolts7 lb-ft10 Nm
Power Window Motor - Rear5 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
- Ground Strap BoltsEnsure clean contact9 lb-ft12 Nm
- Module Mounting Bolts6 lb-ft8 Nm
- Sensor Mounting Bolts7 lb-ft10 Nm
Power Window Regulator - Front5 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
- Ground Strap BoltsEnsure clean contact9 lb-ft12 Nm
- Module Mounting Bolts6 lb-ft8 Nm
- Sensor Mounting Bolts7 lb-ft10 Nm
Power Window Regulator - Rear5 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
- Ground Strap BoltsEnsure clean contact9 lb-ft12 Nm
- Module Mounting Bolts6 lb-ft8 Nm
- Sensor Mounting Bolts7 lb-ft10 Nm
Radio/Head Unit5 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
- Ground Strap BoltsEnsure clean contact9 lb-ft12 Nm
- Module Mounting Bolts6 lb-ft8 Nm
- Sensor Mounting Bolts7 lb-ft10 Nm
Relay - Generic5 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
- Ground Strap BoltsEnsure clean contact9 lb-ft12 Nm
- Module Mounting Bolts6 lb-ft8 Nm
- Sensor Mounting Bolts7 lb-ft10 Nm
Seat Heater Element5 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
- Ground Strap BoltsEnsure clean contact9 lb-ft12 Nm
- Module Mounting Bolts6 lb-ft8 Nm
- Sensor Mounting Bolts7 lb-ft10 Nm
Side Mirror Assembly5 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
- Ground Strap BoltsEnsure clean contact9 lb-ft12 Nm
- Module Mounting Bolts6 lb-ft8 Nm
- Sensor Mounting Bolts7 lb-ft10 Nm
Speaker - Dash5 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
- Ground Strap BoltsEnsure clean contact9 lb-ft12 Nm
- Module Mounting Bolts6 lb-ft8 Nm
- Sensor Mounting Bolts7 lb-ft10 Nm
Speaker - Door5 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
- Ground Strap BoltsEnsure clean contact9 lb-ft12 Nm
- Module Mounting Bolts6 lb-ft8 Nm
- Sensor Mounting Bolts7 lb-ft10 Nm
Speedometer5 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
- Ground Strap BoltsEnsure clean contact9 lb-ft12 Nm
- Module Mounting Bolts6 lb-ft8 Nm
- Sensor Mounting Bolts7 lb-ft10 Nm
Speedometer Cable4 specs
- Battery Terminal Bolts5 lb-ft7 Nm
- Cable FittingHand tight7 lb-ft10 Nm
- Connector Screws3 lb-ft4 Nm
- Ground Strap BoltsClean contact surfaces10 lb-ft14 Nm
Starter3 specs
- Heat Shield BoltsIf equipped7 lb-ft10 Nm
- Starter Mounting BoltLong bolt may need extension37 lb-ft50 Nm
- Starter Solenoid NutFor B+ cable9 lb-ft12 Nm
Starter Solenoid7 specs
- Battery Cable Nut10 lb-ft13 Nm
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
- Ground Strap BoltsEnsure clean contact9 lb-ft12 Nm
- Module Mounting Bolts6 lb-ft8 Nm
- Sensor Mounting Bolts7 lb-ft10 Nm
- Starter Mounting Bolt33 lb-ft45 Nm
Subwoofer5 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
- Ground Strap BoltsEnsure clean contact9 lb-ft12 Nm
- Module Mounting Bolts6 lb-ft8 Nm
- Sensor Mounting Bolts7 lb-ft10 Nm
Sunroof Motor5 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
- Ground Strap BoltsEnsure clean contact9 lb-ft12 Nm
- Module Mounting Bolts6 lb-ft8 Nm
- Sensor Mounting Bolts7 lb-ft10 Nm
Sunroof Switch5 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
- Ground Strap BoltsEnsure clean contact9 lb-ft12 Nm
- Module Mounting Bolts6 lb-ft8 Nm
- Sensor Mounting Bolts7 lb-ft10 Nm
Tail Light Assembly5 specs
- Battery Terminal Bolts5 lb-ft7 Nm
- Connector Screws3 lb-ft4 Nm
- Ground Strap BoltsClean contact surfaces10 lb-ft14 Nm
- Lens Screws1.5 lb-ft2 Nm
- Tail Light Bolts6 lb-ft8 Nm
Tail Light Bulb5 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
- Ground Strap BoltsEnsure clean contact9 lb-ft12 Nm
- Module Mounting Bolts6 lb-ft8 Nm
- Sensor Mounting Bolts7 lb-ft10 Nm
Third Brake Light5 specs
- Battery Terminal BoltsDo not overtighten. Verify sequence with the service manual4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
- Ground Strap BoltsEnsure clean contact. Verify sequence with the service manual9 lb-ft12 Nm
- Module Mounting BoltsVerify sequence with the service manual6 lb-ft8 Nm
- Sensor Mounting BoltsVerify sequence with the service manual7 lb-ft10 Nm
Trunk/Liftgate Actuator5 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
- Ground Strap BoltsEnsure clean contact9 lb-ft12 Nm
- Module Mounting Bolts6 lb-ft8 Nm
- Sensor Mounting Bolts7 lb-ft10 Nm
Turn Signal Bulb - Front5 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
- Ground Strap BoltsEnsure clean contact9 lb-ft12 Nm
- Module Mounting Bolts6 lb-ft8 Nm
- Sensor Mounting Bolts7 lb-ft10 Nm
Turn Signal Bulb - Rear5 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
- Ground Strap BoltsEnsure clean contact9 lb-ft12 Nm
- Module Mounting Bolts6 lb-ft8 Nm
- Sensor Mounting Bolts7 lb-ft10 Nm
Turn Signal Switch5 specs
- Battery Terminal Bolts5 lb-ft7 Nm
- Connector Screws3 lb-ft4 Nm
- Ground Strap BoltsClean contact surfaces10 lb-ft14 Nm
- Steering Column Covers1.5 lb-ft2 Nm
- Switch Mounting Screws2 lb-ft3 Nm
Voltage Regulator5 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
- Ground Strap BoltsEnsure clean contact9 lb-ft12 Nm
- Module Mounting Bolts6 lb-ft8 Nm
- Sensor Mounting Bolts7 lb-ft10 Nm
Washer Pump5 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
- Ground Strap BoltsEnsure clean contact9 lb-ft12 Nm
- Module Mounting Bolts6 lb-ft8 Nm
- Sensor Mounting Bolts7 lb-ft10 Nm
Washer Reservoir5 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
- Ground Strap BoltsEnsure clean contact9 lb-ft12 Nm
- Module Mounting Bolts6 lb-ft8 Nm
- Sensor Mounting Bolts7 lb-ft10 Nm
Window Motor and Regulator - Front5 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
- Ground Strap BoltsEnsure clean contact9 lb-ft12 Nm
- Module Mounting Bolts6 lb-ft8 Nm
- Sensor Mounting Bolts7 lb-ft10 Nm
Window Motor and Regulator - Rear5 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
- Ground Strap BoltsEnsure clean contact9 lb-ft12 Nm
- Module Mounting Bolts6 lb-ft8 Nm
- Sensor Mounting Bolts7 lb-ft10 Nm
Wiper Linkage7 specs
- Battery Terminal Bolts5 lb-ft7 Nm
- Connector Screws3 lb-ft4 Nm
- Ground Strap BoltsEnsure clean contact9 lb-ft12 Nm
- Linkage Pivot Nuts9 lb-ft12 Nm
- Module Mounting Bolts6 lb-ft8 Nm
- Motor Mounting Bolts7 lb-ft10 Nm
- Sensor Mounting Bolts7 lb-ft10 Nm
Wiper Motor - Front5 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
- Ground Strap BoltsEnsure clean contact9 lb-ft12 Nm
- Module Mounting Bolts6 lb-ft8 Nm
- Sensor Mounting Bolts7 lb-ft10 Nm
Wiper Motor - Rear5 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
- Ground Strap BoltsEnsure clean contact9 lb-ft12 Nm
- Module Mounting Bolts6 lb-ft8 Nm
- Sensor Mounting Bolts7 lb-ft10 Nm
Wiper Switch5 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
- Ground Strap BoltsEnsure clean contact9 lb-ft12 Nm
- Module Mounting Bolts6 lb-ft8 Nm
- Sensor Mounting Bolts7 lb-ft10 Nm

Suspension

Ball Joint - Lower8 specs
- Control Arm BoltsTorque with vehicle weight on wheels122 lb-ft165 Nm
- Lower Ball Joint NutUse new cotter pin62 lb-ft84 Nm
- Pinch BoltNew bolt43 lb-ft58 Nm
- Strut Bolts81 lb-ft110 Nm
- Strut Tower Nuts37 lb-ft50 Nm
- Sway Bar Link43 lb-ft58 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug NutsTorque in star pattern65 lb-ft88 Nm
Ball Joints - Upper and Lower8 specs
- Control Arm BoltsTorque with vehicle weight on wheels122 lb-ft165 Nm
- Lower Ball Joint NutUse new cotter pin62 lb-ft84 Nm
- Pinch BoltNew bolt43 lb-ft58 Nm
- Strut Bolts81 lb-ft110 Nm
- Strut Tower Nuts37 lb-ft50 Nm
- Sway Bar Link43 lb-ft58 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug NutsTorque in star pattern65 lb-ft88 Nm
Coil Spring - Front6 specs
- Control Arm BoltsTorque with vehicle weight on wheels122 lb-ft165 Nm
- Strut Bolts81 lb-ft110 Nm
- Strut Tower Nuts37 lb-ft50 Nm
- Sway Bar Link43 lb-ft58 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug NutsTorque in star pattern65 lb-ft88 Nm
Coil Spring - Rear6 specs
- Control Arm BoltsTorque with vehicle weight on wheels122 lb-ft165 Nm
- Strut Bolts81 lb-ft110 Nm
- Strut Tower Nuts37 lb-ft50 Nm
- Sway Bar Link43 lb-ft58 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug NutsTorque in star pattern65 lb-ft88 Nm
Coil Springs - Front Pair6 specs
- Control Arm BoltsTorque with vehicle weight on wheels122 lb-ft165 Nm
- Strut Bolts81 lb-ft110 Nm
- Strut Tower Nuts37 lb-ft50 Nm
- Sway Bar Link43 lb-ft58 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug NutsTorque in star pattern65 lb-ft88 Nm
Coil Springs - Rear Pair6 specs
- Control Arm BoltsTorque with vehicle weight on wheels122 lb-ft165 Nm
- Strut Bolts81 lb-ft110 Nm
- Strut Tower Nuts37 lb-ft50 Nm
- Sway Bar Link43 lb-ft58 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug NutsTorque in star pattern65 lb-ft88 Nm
Control Arm Bushing - Front Lower7 specs
- Control Arm BoltsTorque with vehicle weight on wheels122 lb-ft165 Nm
- Lower Ball Joint NutUse new cotter pin62 lb-ft84 Nm
- Strut Bolts81 lb-ft110 Nm
- Strut Tower Nuts37 lb-ft50 Nm
- Sway Bar Link43 lb-ft58 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug NutsTorque in star pattern65 lb-ft88 Nm
Control Arm Bushing - Rear7 specs
- Ball Joint NutUse new cotter pin62 lb-ft84 Nm
- Control Arm BoltsTorque with vehicle weight on wheels122 lb-ft165 Nm
- Strut Bolts81 lb-ft110 Nm
- Strut Tower Nuts37 lb-ft50 Nm
- Sway Bar Link43 lb-ft58 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug NutsTorque in star pattern65 lb-ft88 Nm
Front Struts - Pair8 specs
- Control Arm BoltsTorque with vehicle weight on wheels122 lb-ft165 Nm
- Strut Bolts81 lb-ft110 Nm
- Strut to Knuckle BoltsClean threads110 lb-ft150 Nm
- Strut Tower Nuts33.2 lb-ft45 Nm
- Sway Bar Link43 lb-ft58 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Upper Mount Nut25 lb-ft34 Nm
- Wheel Lug NutsTorque in star pattern65 lb-ft88 Nm
Front Suspension Rebuild4 specs
- Ball Joint Pinch BoltUse new bolt if locknut style37 lb-ft50 Nm
- Lower Control Arm BoltsTorque at ride height81 lb-ft110 Nm
- Strut Top Mount Nuts18 lb-ft25 Nm
- Sway Bar End Link Nuts44 lb-ft60 Nm
Knuckle/Spindle - Front7 specs
- Control Arm BoltsTorque with vehicle weight on wheels122 lb-ft165 Nm
- Lower Ball Joint NutUse new cotter pin62 lb-ft84 Nm
- Strut Bolts81 lb-ft110 Nm
- Strut Tower Nuts37 lb-ft50 Nm
- Sway Bar Link43 lb-ft58 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug NutsTorque in star pattern65 lb-ft88 Nm
Knuckle/Spindle - Rear7 specs
- Ball Joint NutUse new cotter pin62 lb-ft84 Nm
- Control Arm BoltsTorque with vehicle weight on wheels122 lb-ft165 Nm
- Strut Bolts81 lb-ft110 Nm
- Strut Tower Nuts37 lb-ft50 Nm
- Sway Bar Link43 lb-ft58 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug NutsTorque in star pattern65 lb-ft88 Nm
Lateral Arm6 specs
- Control Arm BoltsTorque with vehicle weight on wheels122 lb-ft165 Nm
- Strut Bolts81 lb-ft110 Nm
- Strut Tower Nuts37 lb-ft50 Nm
- Sway Bar Link43 lb-ft58 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug NutsTorque in star pattern65 lb-ft88 Nm
Lower Control Arm - Front5 specs
- Control Arm BoltsTorque at ride height100 lb-ft135 Nm
- Lower Ball Joint NutDo not loosen to align pin - tighten further50 lb-ft68 Nm
- Strut Bolts81 lb-ft110 Nm
- Sway Bar Link43 lb-ft58 Nm
- Wheel Lug NutsTorque in star pattern65 lb-ft88 Nm
Lower Control Arm - Rear7 specs
- Control Arm BoltsTorque with vehicle weight on wheels122 lb-ft165 Nm
- Lower Ball Joint NutUse new cotter pin62 lb-ft84 Nm
- Strut Bolts81 lb-ft110 Nm
- Strut Tower Nuts37 lb-ft50 Nm
- Sway Bar Link43 lb-ft58 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug NutsTorque in star pattern65 lb-ft88 Nm
Radius Arm6 specs
- Control Arm BoltsTorque with vehicle weight on wheels122 lb-ft165 Nm
- Strut Bolts81 lb-ft110 Nm
- Strut Tower Nuts37 lb-ft50 Nm
- Sway Bar Link43 lb-ft58 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug NutsTorque in star pattern65 lb-ft88 Nm
Radius Arm Bushing6 specs
- Control Arm BoltsTorque with vehicle weight on wheels122 lb-ft165 Nm
- Strut Bolts81 lb-ft110 Nm
- Strut Tower Nuts37 lb-ft50 Nm
- Sway Bar Link43 lb-ft58 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug NutsTorque in star pattern65 lb-ft88 Nm
Rear Shocks - Pair6 specs
- Control Arm BoltsTorque with vehicle weight on wheels122 lb-ft165 Nm
- Strut Bolts81 lb-ft110 Nm
- Strut Tower Nuts37 lb-ft50 Nm
- Sway Bar Link43 lb-ft58 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug NutsTorque in star pattern65 lb-ft88 Nm
Rear Suspension Service4 specs
- Lower Control Arm BoltsTorque at ride height66 lb-ft90 Nm
- Shock Lower Bolt52 lb-ft70 Nm
- Sway Bar End Link Nuts37 lb-ft50 Nm
- Trailing Arm BoltsTorque at ride height88 lb-ft120 Nm
Shock Absorber Replacement2 specs
- Lower Mount Bolt66 lb-ft90 Nm
- Upper Mount NutUse new self-locking nut41 lb-ft55 Nm
Strut Assembly - Rear7 specs
- Control Arm BoltsTorque with vehicle weight on wheels122 lb-ft165 Nm
- Strut Bolts81 lb-ft110 Nm
- Strut to Knuckle Bolts72 lb-ft98 Nm
- Strut Tower Nuts37 lb-ft50 Nm
- Sway Bar Link43 lb-ft58 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug NutsTorque in star pattern65 lb-ft88 Nm
Strut Bearing7 specs
- Control Arm BoltsTorque with vehicle weight on wheels122 lb-ft165 Nm
- Strut Bolts81 lb-ft110 Nm
- Strut to Knuckle Bolts86 lb-ft116 Nm
- Strut Tower Nuts37 lb-ft50 Nm
- Sway Bar Link43 lb-ft58 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug NutsTorque in star pattern65 lb-ft88 Nm
Strut Mount - Front7 specs
- Control Arm BoltsTorque with vehicle weight on wheels122 lb-ft165 Nm
- Strut Bolts81 lb-ft110 Nm
- Strut to Knuckle Bolts81 lb-ft110 Nm
- Strut Tower Nuts37 lb-ft50 Nm
- Sway Bar Link43 lb-ft58 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug NutsTorque in star pattern65 lb-ft88 Nm
Strut Mount - Rear7 specs
- Control Arm BoltsTorque with vehicle weight on wheels122 lb-ft165 Nm
- Strut Bolts81 lb-ft110 Nm
- Strut to Knuckle Bolts72 lb-ft98 Nm
- Strut Tower Nuts37 lb-ft50 Nm
- Sway Bar Link43 lb-ft58 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug NutsTorque in star pattern65 lb-ft88 Nm
Subframe6 specs
- Control Arm BoltsTorque with vehicle weight on wheels122 lb-ft165 Nm
- Strut Bolts81 lb-ft110 Nm
- Strut Tower Nuts37 lb-ft50 Nm
- Sway Bar Link43 lb-ft58 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug NutsTorque in star pattern65 lb-ft88 Nm
Subframe Bushing6 specs
- Control Arm BoltsTorque with vehicle weight on wheels122 lb-ft165 Nm
- Strut Bolts81 lb-ft110 Nm
- Strut Tower Nuts37 lb-ft50 Nm
- Sway Bar Link43 lb-ft58 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug NutsTorque in star pattern65 lb-ft88 Nm
Sway Bar - Front7 specs
- Control Arm BoltsTorque with vehicle weight on wheels122 lb-ft165 Nm
- Strut Bolts81 lb-ft110 Nm
- Strut Tower Nuts37 lb-ft50 Nm
- Sway Bar Bracket Bolts33 lb-ft45 Nm
- Sway Bar Link43 lb-ft58 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug NutsTorque in star pattern65 lb-ft88 Nm
Sway Bar - Rear7 specs
- Control Arm BoltsTorque with vehicle weight on wheels122 lb-ft165 Nm
- Strut Bolts81 lb-ft110 Nm
- Strut Tower Nuts37 lb-ft50 Nm
- Sway Bar Bracket Bolts33 lb-ft45 Nm
- Sway Bar Link43 lb-ft58 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug NutsTorque in star pattern65 lb-ft88 Nm
Sway Bar Bushing - Front7 specs
- Control Arm BoltsTorque with vehicle weight on wheels122 lb-ft165 Nm
- Strut Bolts81 lb-ft110 Nm
- Strut Tower Nuts37 lb-ft50 Nm
- Sway Bar Bracket Bolts33 lb-ft45 Nm
- Sway Bar Link43 lb-ft58 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug NutsTorque in star pattern65 lb-ft88 Nm
Sway Bar Bushing - Rear7 specs
- Control Arm BoltsTorque with vehicle weight on wheels122 lb-ft165 Nm
- Strut Bolts81 lb-ft110 Nm
- Strut Tower Nuts37 lb-ft50 Nm
- Sway Bar Bracket Bolts33 lb-ft45 Nm
- Sway Bar Link43 lb-ft58 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug NutsTorque in star pattern65 lb-ft88 Nm
Sway Bar Link - Front7 specs
- Control Arm BoltsTorque with vehicle weight on wheels122 lb-ft165 Nm
- Strut Bolts81 lb-ft110 Nm
- Strut Tower Nuts37 lb-ft50 Nm
- Sway Bar Bracket Bolts33 lb-ft45 Nm
- Sway Bar Link43 lb-ft58 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug NutsTorque in star pattern65 lb-ft88 Nm
Sway Bar Link - Rear7 specs
- Control Arm BoltsTorque with vehicle weight on wheels122 lb-ft165 Nm
- Strut Bolts81 lb-ft110 Nm
- Strut Tower Nuts37 lb-ft50 Nm
- Sway Bar Bracket Bolts33 lb-ft45 Nm
- Sway Bar Link43 lb-ft58 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug NutsTorque in star pattern65 lb-ft88 Nm
Sway Bar Links - Front Pair7 specs
- Control Arm BoltsTorque with vehicle weight on wheels122 lb-ft165 Nm
- Strut Bolts81 lb-ft110 Nm
- Strut Tower Nuts37 lb-ft50 Nm
- Sway Bar Bracket Bolts33 lb-ft45 Nm
- Sway Bar Link43 lb-ft58 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug NutsTorque in star pattern65 lb-ft88 Nm
Torsion Bar6 specs
- Control Arm BoltsTorque with vehicle weight on wheels122 lb-ft165 Nm
- Strut Bolts81 lb-ft110 Nm
- Strut Tower Nuts37 lb-ft50 Nm
- Sway Bar Link43 lb-ft58 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug NutsTorque in star pattern65 lb-ft88 Nm
Torsion Bar Adjustment6 specs
- Control Arm BoltsTorque with vehicle weight on wheels122 lb-ft165 Nm
- Strut Bolts81 lb-ft110 Nm
- Strut Tower Nuts37 lb-ft50 Nm
- Sway Bar Link43 lb-ft58 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug NutsTorque in star pattern65 lb-ft88 Nm
Trailing Arm6 specs
- Control Arm BoltsTorque with vehicle weight on wheels122 lb-ft165 Nm
- Strut Bolts81 lb-ft110 Nm
- Strut Tower Nuts37 lb-ft50 Nm
- Sway Bar Link43 lb-ft58 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug NutsTorque in star pattern65 lb-ft88 Nm
Trailing Arm Bushing6 specs
- Control Arm BoltsTorque with vehicle weight on wheels122 lb-ft165 Nm
- Strut Bolts81 lb-ft110 Nm
- Strut Tower Nuts37 lb-ft50 Nm
- Sway Bar Link43 lb-ft58 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug NutsTorque in star pattern65 lb-ft88 Nm
Upper Control Arm - Rear7 specs
- Control Arm BoltsTorque with vehicle weight on wheels122 lb-ft165 Nm
- Strut Bolts81 lb-ft110 Nm
- Strut Tower Nuts37 lb-ft50 Nm
- Sway Bar Link43 lb-ft58 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Upper Ball Joint NutUse new cotter pin62 lb-ft84 Nm
- Wheel Lug NutsTorque in star pattern65 lb-ft88 Nm

Steering

Power Steering Fluid Flush7 specs
- Coupling Bolt24 lb-ft33 Nm
- Power Steering Line FittingsUse new O-rings22 lb-ft30 Nm
- Steering Rack Bolts71 lb-ft96 Nm
- Tie Rod End Castle NutUse new cotter pin32 lb-ft44 Nm
- Tie Rod End NutUse new cotter pin32 lb-ft44 Nm
- Tie Rod Nut38 lb-ft52 Nm
- Wheel Lug Nuts65 lb-ft88 Nm
Power Steering Hose - High Pressure7 specs
- Coupling Bolt24 lb-ft33 Nm
- Power Steering Line FittingsUse new O-rings22 lb-ft30 Nm
- Steering Rack Bolts71 lb-ft96 Nm
- Tie Rod End Castle NutUse new cotter pin32 lb-ft44 Nm
- Tie Rod End NutUse new cotter pin32 lb-ft44 Nm
- Tie Rod Nut38 lb-ft52 Nm
- Wheel Lug Nuts65 lb-ft88 Nm
Power Steering Hose - Return7 specs
- Coupling Bolt24 lb-ft33 Nm
- Power Steering Line FittingsUse new O-rings22 lb-ft30 Nm
- Steering Rack Bolts71 lb-ft96 Nm
- Tie Rod End Castle NutUse new cotter pin32 lb-ft44 Nm
- Tie Rod End NutUse new cotter pin32 lb-ft44 Nm
- Tie Rod Nut38 lb-ft52 Nm
- Wheel Lug Nuts65 lb-ft88 Nm
Power Steering Pump8 specs
- High Pressure Hose FittingUse new O-rings18 lb-ft25 Nm
- Power Steering Pump Bolts18 lb-ft25 Nm
- Pressure Line FittingUse new O-rings22 lb-ft30 Nm
- Pulley NutHold pulley with pin spanner52 lb-ft70 Nm
- Pump Mounting Bolts18 lb-ft25 Nm
- Return Hose Clamp2 lb-ft3 Nm
- Return Line Clamp3 lb-ft4 Nm
- Serpentine Belt Tensioner41 lb-ft55 Nm
Power Steering Pump Pulley9 specs
- Coupling Bolt24 lb-ft33 Nm
- Power Steering Line FittingsUse new O-rings. Verify sequence with the service manual22 lb-ft30 Nm
- Pressure Line FittingNew O-ring24 lb-ft32 Nm
- Pump Mounting Bolts19 lb-ft26 Nm
- Steering Rack Bolts71 lb-ft96 Nm
- Tie Rod End Castle NutUse new cotter pin. Verify sequence with the service manual32 lb-ft44 Nm
- Tie Rod End NutUse new cotter pin32 lb-ft44 Nm
- Tie Rod Nut38 lb-ft52 Nm
- Wheel Lug Nuts65 lb-ft88 Nm
Power Steering Rack9 specs
- Coupling Bolt24 lb-ft33 Nm
- Power Steering Line FittingsUse new O-rings. Verify sequence with the service manual22 lb-ft30 Nm
- Pressure Line FittingNew O-ring24 lb-ft32 Nm
- Pump Mounting Bolts19 lb-ft26 Nm
- Steering Rack Bolts71 lb-ft96 Nm
- Tie Rod End Castle NutUse new cotter pin. Verify sequence with the service manual32 lb-ft44 Nm
- Tie Rod End NutUse new cotter pin32 lb-ft44 Nm
- Tie Rod Nut38 lb-ft52 Nm
- Wheel Lug Nuts65 lb-ft88 Nm
Power Steering Reservoir7 specs
- Coupling Bolt24 lb-ft33 Nm
- Power Steering Line FittingsUse new O-rings22 lb-ft30 Nm
- Steering Rack Bolts71 lb-ft96 Nm
- Tie Rod End Castle NutUse new cotter pin32 lb-ft44 Nm
- Tie Rod End NutUse new cotter pin32 lb-ft44 Nm
- Tie Rod Nut38 lb-ft52 Nm
- Wheel Lug Nuts65 lb-ft88 Nm
Rack and Pinion Boots7 specs
- Coupling Bolt24 lb-ft33 Nm
- Power Steering Line FittingsUse new O-rings22 lb-ft30 Nm
- Steering Rack Bolts71 lb-ft96 Nm
- Tie Rod End Castle NutUse new cotter pin32 lb-ft44 Nm
- Tie Rod End NutUse new cotter pin32 lb-ft44 Nm
- Tie Rod Nut38 lb-ft52 Nm
- Wheel Lug Nuts65 lb-ft88 Nm
Steering Angle Sensor7 specs
- Coupling Bolt24 lb-ft33 Nm
- Power Steering Line FittingsUse new O-rings. Verify sequence with the service manual22 lb-ft30 Nm
- Steering Rack Bolts71 lb-ft96 Nm
- Tie Rod End Castle NutUse new cotter pin. Verify sequence with the service manual32 lb-ft44 Nm
- Tie Rod End NutUse new cotter pin32 lb-ft44 Nm
- Tie Rod Nut38 lb-ft52 Nm
- Wheel Lug Nuts65 lb-ft88 Nm
Steering Column9 specs
- Coupling Bolt24 lb-ft33 Nm
- Ignition Switch BoltsVerify sequence with the service manual4 lb-ft5 Nm
- Pinch BoltVerify sequence with the service manual22 lb-ft30 Nm
- Power Steering Line FittingsUse new O-rings24 lb-ft33 Nm
- Steering Column BoltsVerify sequence with the service manual22 lb-ft30 Nm
- Steering Rack Bolts71 lb-ft96 Nm
- Tie Rod End NutUse new cotter pin32 lb-ft44 Nm
- Tie Rod Nut38 lb-ft52 Nm
- Wheel Lug Nuts65 lb-ft88 Nm
Steering Coupler7 specs
- Coupling Bolt24 lb-ft33 Nm
- Power Steering Line FittingsUse new O-rings. Verify sequence with the service manual22 lb-ft30 Nm
- Steering Rack Bolts71 lb-ft96 Nm
- Tie Rod End Castle NutUse new cotter pin. Verify sequence with the service manual32 lb-ft44 Nm
- Tie Rod End NutUse new cotter pin32 lb-ft44 Nm
- Tie Rod Nut38 lb-ft52 Nm
- Wheel Lug Nuts65 lb-ft88 Nm
Steering Damper7 specs
- Coupling Bolt24 lb-ft33 Nm
- Power Steering Line FittingsUse new O-rings. Verify sequence with the service manual22 lb-ft30 Nm
- Steering Rack Bolts71 lb-ft96 Nm
- Tie Rod End Castle NutUse new cotter pin. Verify sequence with the service manual32 lb-ft44 Nm
- Tie Rod End NutUse new cotter pin32 lb-ft44 Nm
- Tie Rod Nut38 lb-ft52 Nm
- Wheel Lug Nuts65 lb-ft88 Nm
Steering Shaft - Intermediate7 specs
- Coupling Bolt24 lb-ft33 Nm
- Power Steering Line FittingsUse new O-rings. Verify sequence with the service manual22 lb-ft30 Nm
- Steering Rack Bolts71 lb-ft96 Nm
- Tie Rod End Castle NutUse new cotter pin. Verify sequence with the service manual32 lb-ft44 Nm
- Tie Rod End NutUse new cotter pin32 lb-ft44 Nm
- Tie Rod Nut38 lb-ft52 Nm
- Wheel Lug Nuts65 lb-ft88 Nm
Steering Shaft - Upper7 specs
- Coupling Bolt24 lb-ft33 Nm
- Power Steering Line FittingsUse new O-rings. Verify sequence with the service manual22 lb-ft30 Nm
- Steering Rack Bolts71 lb-ft96 Nm
- Tie Rod End Castle NutUse new cotter pin. Verify sequence with the service manual32 lb-ft44 Nm
- Tie Rod End NutUse new cotter pin32 lb-ft44 Nm
- Tie Rod Nut38 lb-ft52 Nm
- Wheel Lug Nuts65 lb-ft88 Nm
Steering Wheel8 specs
- Airbag Module BoltsTorx - usually T30. Verify sequence with the service manual5 lb-ft7 Nm
- Coupling Bolt24 lb-ft33 Nm
- Power Steering Line FittingsUse new O-rings24 lb-ft33 Nm
- Steering Rack Bolts71 lb-ft96 Nm
- Steering Wheel NutVerify sequence with the service manual40 lb-ft54 Nm
- Tie Rod End NutUse new cotter pin32 lb-ft44 Nm
- Tie Rod Nut38 lb-ft52 Nm
- Wheel Lug Nuts65 lb-ft88 Nm
Tie Rod Assembly8 specs
- Coupling Bolt24 lb-ft33 Nm
- Power Steering Line FittingsUse new O-rings22 lb-ft30 Nm
- Steering Rack Bolts71 lb-ft96 Nm
- Tie Rod End Castle NutUse new cotter pin32 lb-ft44 Nm
- Tie Rod End NutUse new cotter pin32 lb-ft44 Nm
- Tie Rod Lock NutAfter alignment48 lb-ft65 Nm
- Tie Rod Nut38 lb-ft52 Nm
- Wheel Lug Nuts65 lb-ft88 Nm
Tie Rod End - Inner8 specs
- Coupling Bolt24 lb-ft33 Nm
- Power Steering Line FittingsUse new O-rings22 lb-ft30 Nm
- Steering Rack Bolts71 lb-ft96 Nm
- Tie Rod End Castle NutUse new cotter pin32 lb-ft44 Nm
- Tie Rod End NutUse new cotter pin32 lb-ft44 Nm
- Tie Rod Lock NutAfter alignment48 lb-ft64 Nm
- Tie Rod Nut38 lb-ft52 Nm
- Wheel Lug Nuts65 lb-ft88 Nm
Tie Rod End - Outer8 specs
- Coupling Bolt24 lb-ft33 Nm
- Power Steering Line FittingsUse new O-rings22 lb-ft30 Nm
- Steering Rack Bolts71 lb-ft96 Nm
- Tie Rod End Castle NutUse new cotter pin32 lb-ft44 Nm
- Tie Rod End NutUse new cotter pin32 lb-ft44 Nm
- Tie Rod Lock NutAfter alignment48 lb-ft64 Nm
- Tie Rod Nut38 lb-ft52 Nm
- Wheel Lug Nuts65 lb-ft88 Nm
Tie Rods - Both Sides8 specs
- Coupling Bolt24 lb-ft33 Nm
- Power Steering Line FittingsUse new O-rings22 lb-ft30 Nm
- Steering Rack Bolts71 lb-ft96 Nm
- Tie Rod End Castle NutUse new cotter pin32 lb-ft44 Nm
- Tie Rod End NutUse new cotter pin32 lb-ft44 Nm
- Tie Rod Lock NutAfter alignment48 lb-ft64 Nm
- Tie Rod Nut38 lb-ft52 Nm
- Wheel Lug Nuts65 lb-ft88 Nm

Drivetrain

Axle Seal - Front7 specs
- Axle NutUse new cotter pin or stake nut170 lb-ft230 Nm
- CV Bolts43 lb-ft58 Nm
- CV Joint Bolts43 lb-ft58 Nm
- Differential Cover Bolts26 lb-ft35 Nm
- Driveshaft Bolts52 lb-ft71 Nm
- Driveshaft U-Joint StrapsTighten evenly15 lb-ft20 Nm
- Wheel Lug NutsTorque in star pattern65 lb-ft88 Nm
CV Axle - Front9 specs
- Axle NutUse new nut, stake after170 lb-ft230 Nm
- Ball Joint Pinch Bolt41 lb-ft55 Nm
- CV Axle NutUse new cotter pin or stake nut170 lb-ft230 Nm
- CV Bolts43 lb-ft58 Nm
- CV Joint Bolts43 lb-ft58 Nm
- Differential Cover BoltsApply RTV sealant24 lb-ft33 Nm
- Driveshaft Bolts52 lb-ft71 Nm
- Lower Ball Joint Nut71 lb-ft97 Nm
- Wheel Lug Nuts65 lb-ft88 Nm
CV Axles - Front Pair8 specs
- Axle NutUse new cotter pin or stake nut170 lb-ft230 Nm
- CV Bolts43 lb-ft58 Nm
- CV Joint Bolts43 lb-ft58 Nm
- Differential Cover Bolts26 lb-ft35 Nm
- Driveshaft Bolts52 lb-ft71 Nm
- Driveshaft U-Joint StrapsTighten evenly15 lb-ft20 Nm
- Lower Ball Joint Nut71 lb-ft97 Nm
- Wheel Lug NutsTorque in star pattern65 lb-ft88 Nm
CV Boot - Inner7 specs
- Axle NutUse new cotter pin or stake nut184 lb-ft250 Nm
- CV Bolts43 lb-ft58 Nm
- CV Joint Bolts43 lb-ft58 Nm
- Differential Cover Bolts26 lb-ft35 Nm
- Driveshaft Bolts52 lb-ft71 Nm
- Driveshaft U-Joint StrapsTighten evenly15 lb-ft20 Nm
- Wheel Lug NutsTorque in star pattern65 lb-ft88 Nm
CV Boot - Outer7 specs
- Axle NutUse new cotter pin or stake nut184 lb-ft250 Nm
- CV Bolts43 lb-ft58 Nm
- CV Joint Bolts43 lb-ft58 Nm
- Differential Cover Bolts26 lb-ft35 Nm
- Driveshaft Bolts52 lb-ft71 Nm
- Driveshaft U-Joint StrapsTighten evenly15 lb-ft20 Nm
- Wheel Lug NutsTorque in star pattern65 lb-ft88 Nm
Differential Cover Gasket6 specs
- Axle NutUse new nut, stake after171 lb-ft232 Nm
- CV Bolts43 lb-ft58 Nm
- CV Joint Bolts43 lb-ft58 Nm
- Differential Cover BoltsApply RTV sealant24 lb-ft33 Nm
- Driveshaft Bolts52 lb-ft71 Nm
- Wheel Lug Nuts65 lb-ft88 Nm
Differential Pinion Seal6 specs
- Axle NutUse new nut, stake after171 lb-ft232 Nm
- CV Bolts43 lb-ft58 Nm
- CV Joint Bolts43 lb-ft58 Nm
- Differential Cover BoltsApply RTV sealant24 lb-ft33 Nm
- Driveshaft Bolts52 lb-ft71 Nm
- Wheel Lug Nuts65 lb-ft88 Nm
Differential Rebuild - Rear8 specs
- Axle NutUse new nut, stake after171 lb-ft232 Nm
- CV Bolts43 lb-ft58 Nm
- CV Joint Bolts43 lb-ft58 Nm
- Differential Cover BoltsApply RTV sealant24 lb-ft33 Nm
- Drain PlugNew washer29 lb-ft39 Nm
- Driveshaft Bolts52 lb-ft71 Nm
- Fill Plug29 lb-ft39 Nm
- Wheel Lug Nuts65 lb-ft88 Nm
Limited Slip Clutch Pack7 specs
- Axle NutUse new cotter pin or stake nut184 lb-ft250 Nm
- CV Bolts43 lb-ft58 Nm
- CV Joint Bolts43 lb-ft58 Nm
- Differential Cover Bolts26 lb-ft35 Nm
- Driveshaft Bolts52 lb-ft71 Nm
- Driveshaft U-Joint StrapsTighten evenly15 lb-ft20 Nm
- Wheel Lug NutsTorque in star pattern65 lb-ft88 Nm
Ring and Pinion7 specs
- Axle NutUse new cotter pin or stake nut184 lb-ft250 Nm
- CV Bolts43 lb-ft58 Nm
- CV Joint Bolts43 lb-ft58 Nm
- Differential Cover Bolts26 lb-ft35 Nm
- Driveshaft Bolts52 lb-ft71 Nm
- Driveshaft U-Joint StrapsTighten evenly15 lb-ft20 Nm
- Wheel Lug NutsTorque in star pattern65 lb-ft88 Nm
U-Joint6 specs
- Axle NutUse new nut, stake after171 lb-ft232 Nm
- CV Bolts43 lb-ft58 Nm
- CV Joint Bolts43 lb-ft58 Nm
- Differential Cover BoltsApply RTV sealant24 lb-ft33 Nm
- Driveshaft Bolts52 lb-ft71 Nm
- Wheel Lug Nuts65 lb-ft88 Nm
Wheel Bearing - Press-In Front8 specs
- ABS Sensor Bolt8 lb-ft10 Nm
- Axle NutUse new cotter pin or stake nut170 lb-ft230 Nm
- CV Joint Bolts43 lb-ft58 Nm
- Differential Cover Bolts26 lb-ft35 Nm
- Driveshaft Bolts52 lb-ft71 Nm
- Driveshaft U-Joint StrapsTighten evenly15 lb-ft20 Nm
- Hub Bolts71 lb-ft97 Nm
- Wheel Lug NutsTorque in star pattern65 lb-ft88 Nm
Wheel Bearing - Press-In Rear8 specs
- ABS Sensor Bolt8 lb-ft10 Nm
- Axle NutUse new cotter pin or stake nut184 lb-ft250 Nm
- CV Joint Bolts43 lb-ft58 Nm
- Differential Cover Bolts26 lb-ft35 Nm
- Driveshaft Bolts52 lb-ft71 Nm
- Driveshaft U-Joint StrapsTighten evenly15 lb-ft20 Nm
- Hub Bolts71 lb-ft97 Nm
- Wheel Lug NutsTorque in star pattern65 lb-ft88 Nm
Wheel Bearing Hub - Front4 specs
- ABS Sensor BoltDo not overtighten7 lb-ft10 Nm
- Axle NutUse new cotter pin after torque170 lb-ft230 Nm
- Caliper Bracket Bolts88 lb-ft120 Nm
- Wheel Bearing Hub BoltsApply threadlocker if specified81 lb-ft110 Nm
Wheel Bearing Hub - Rear3 specs
- Axle NutUse new cotter pin after torque148 lb-ft200 Nm
- Caliper Bracket Bolts81 lb-ft110 Nm
- Wheel Bearing Hub BoltsApply threadlocker if specified74 lb-ft100 Nm
Wheel Studs7 specs
- Axle NutUse new cotter pin or stake nut184 lb-ft250 Nm
- CV Bolts43 lb-ft58 Nm
- CV Joint Bolts43 lb-ft58 Nm
- Differential Cover Bolts26 lb-ft35 Nm
- Driveshaft Bolts52 lb-ft71 Nm
- Driveshaft U-Joint StrapsTighten evenly15 lb-ft20 Nm
- Wheel Lug NutsTorque in star pattern65 lb-ft88 Nm

Transmission

Clutch Hydraulic Line7 specs
- Bell Housing Bolts33 lb-ft45 Nm
- Drain PlugUse new washer24 lb-ft33 Nm
- Fill Plug24 lb-ft33 Nm
- Flywheel BoltsOften TTY, tighten in star pattern70 lb-ft95 Nm
- Pressure Plate BoltStar pattern19 lb-ft26 Nm
- Transmission Drain PlugUse new crush washer if equipped22 lb-ft30 Nm
- Transmission Pan BoltsTighten in criss-cross pattern9 lb-ft12 Nm
Dual Mass Flywheel5 specs
- Drain PlugUse new washer24 lb-ft33 Nm
- Fill Plug24 lb-ft33 Nm
- Flywheel BoltsOften TTY, tighten in star pattern70 lb-ft95 Nm
- Transmission Drain PlugUse new crush washer if equipped22 lb-ft30 Nm
- Transmission Pan BoltsTighten in criss-cross pattern9 lb-ft12 Nm
Kickdown Cable5 specs
- Drain PlugUse new washer24 lb-ft33 Nm
- Fill Plug24 lb-ft33 Nm
- Flywheel BoltsOften TTY, tighten in star pattern70 lb-ft95 Nm
- Transmission Drain PlugUse new crush washer if equipped22 lb-ft30 Nm
- Transmission Pan BoltsTighten in criss-cross pattern9 lb-ft12 Nm
Manual Trans Fluid Change5 specs
- Drain PlugUse new washer24 lb-ft33 Nm
- Fill Plug24 lb-ft33 Nm
- Flywheel BoltsOften TTY, tighten in star pattern70 lb-ft95 Nm
- Transmission Drain PlugUse new crush washer if equipped22 lb-ft30 Nm
- Transmission Pan BoltsTighten in criss-cross pattern9 lb-ft12 Nm
Neutral Safety Switch3 specs
- Drain PlugUse new washer24 lb-ft33 Nm
- Fill Plug24 lb-ft33 Nm
- Switch Mounting Bolts11 lb-ft15 Nm
Overdrive Solenoid5 specs
- Drain PlugUse new washer24 lb-ft33 Nm
- Fill Plug24 lb-ft33 Nm
- Flywheel BoltsOften TTY, tighten in star pattern70 lb-ft95 Nm
- Transmission Drain PlugUse new crush washer if equipped22 lb-ft30 Nm
- Transmission Pan BoltsTighten in criss-cross pattern9 lb-ft12 Nm
Pressure Plate5 specs
- Drain PlugUse new washer24 lb-ft33 Nm
- Fill Plug24 lb-ft33 Nm
- Flywheel BoltsOften TTY, tighten in star pattern70 lb-ft95 Nm
- Transmission Drain PlugUse new crush washer if equipped22 lb-ft30 Nm
- Transmission Pan BoltsTighten in criss-cross pattern9 lb-ft12 Nm
Shift Cable4 specs
- Adjustment Nut7 lb-ft10 Nm
- Cable Bracket Bolts11 lb-ft15 Nm
- Drain PlugUse new washer24 lb-ft33 Nm
- Fill Plug24 lb-ft33 Nm
Shift Fork5 specs
- Drain PlugUse new washer24 lb-ft33 Nm
- Fill Plug24 lb-ft33 Nm
- Flywheel BoltsOften TTY, tighten in star pattern70 lb-ft95 Nm
- Transmission Drain PlugUse new crush washer if equipped22 lb-ft30 Nm
- Transmission Pan BoltsTighten in criss-cross pattern9 lb-ft12 Nm
Shift Linkage4 specs
- Drain PlugUse new washer24 lb-ft33 Nm
- Fill Plug24 lb-ft33 Nm
- Linkage Bolts11 lb-ft15 Nm
- Pivot Bolts9 lb-ft12 Nm
Shift Solenoid - Single5 specs
- Drain PlugUse new washer24 lb-ft33 Nm
- Fill Plug24 lb-ft33 Nm
- Flywheel BoltsOften TTY, tighten in star pattern70 lb-ft95 Nm
- Transmission Drain PlugUse new crush washer if equipped22 lb-ft30 Nm
- Transmission Pan BoltsTighten in criss-cross pattern9 lb-ft12 Nm
Shift Solenoids - All5 specs
- Drain PlugUse new washer24 lb-ft33 Nm
- Fill Plug24 lb-ft33 Nm
- Flywheel BoltsOften TTY, tighten in star pattern70 lb-ft95 Nm
- Transmission Drain PlugUse new crush washer if equipped22 lb-ft30 Nm
- Transmission Pan BoltsTighten in criss-cross pattern9 lb-ft12 Nm
Synchros - All5 specs
- Drain PlugUse new washer24 lb-ft33 Nm
- Fill Plug24 lb-ft33 Nm
- Flywheel BoltsOften TTY, tighten in star pattern70 lb-ft95 Nm
- Transmission Drain PlugUse new crush washer if equipped22 lb-ft30 Nm
- Transmission Pan BoltsTighten in criss-cross pattern9 lb-ft12 Nm
Synchros - Single Gear5 specs
- Drain PlugUse new washer24 lb-ft33 Nm
- Fill Plug24 lb-ft33 Nm
- Flywheel BoltsOften TTY, tighten in star pattern70 lb-ft95 Nm
- Transmission Drain PlugUse new crush washer if equipped22 lb-ft30 Nm
- Transmission Pan BoltsTighten in criss-cross pattern9 lb-ft12 Nm
Torque Converter4 specs
- Drain PlugUse new washer24 lb-ft33 Nm
- Fill Plug24 lb-ft33 Nm
- Flexplate BoltsAutomatic transmissions63 lb-ft85 Nm
- Torque Converter BoltsTighten evenly37 lb-ft50 Nm
Torque Converter Clutch Solenoid5 specs
- Drain PlugUse new washer24 lb-ft33 Nm
- Fill Plug24 lb-ft33 Nm
- Flywheel BoltsOften TTY, tighten in star pattern70 lb-ft95 Nm
- Transmission Drain PlugUse new crush washer if equipped22 lb-ft30 Nm
- Transmission Pan BoltsTighten in criss-cross pattern9 lb-ft12 Nm
Transmission Control Module5 specs
- Drain PlugUse new washer24 lb-ft33 Nm
- Fill Plug24 lb-ft33 Nm
- Flywheel BoltsOften TTY, tighten in star pattern70 lb-ft95 Nm
- Transmission Drain PlugUse new crush washer if equipped22 lb-ft30 Nm
- Transmission Pan BoltsTighten in criss-cross pattern9 lb-ft12 Nm
Transmission Cooler Lines5 specs
- Drain PlugUse new washer24 lb-ft33 Nm
- Fill Plug24 lb-ft33 Nm
- Flywheel BoltsOften TTY, tighten in star pattern70 lb-ft95 Nm
- Transmission Drain PlugUse new crush washer if equipped22 lb-ft30 Nm
- Transmission Pan BoltsTighten in criss-cross pattern9 lb-ft12 Nm
Transmission Filter5 specs
- Drain PlugUse new washer24 lb-ft33 Nm
- Fill Plug24 lb-ft33 Nm
- Flywheel BoltsOften TTY, tighten in star pattern70 lb-ft95 Nm
- Transmission Drain PlugUse new crush washer if equipped22 lb-ft30 Nm
- Transmission Pan BoltsTighten in criss-cross pattern9 lb-ft12 Nm
Transmission Filter and Fluid5 specs
- Drain PlugUse new washer24 lb-ft33 Nm
- Fill Plug24 lb-ft33 Nm
- Flywheel BoltsOften TTY, tighten in star pattern70 lb-ft95 Nm
- Transmission Drain PlugUse new crush washer if equipped22 lb-ft30 Nm
- Transmission Pan BoltsTighten in criss-cross pattern9 lb-ft12 Nm
Transmission Fluid Change6 specs
- Drain PlugUse new washer24 lb-ft33 Nm
- Fill Plug24 lb-ft33 Nm
- Flywheel BoltsOften TTY, tighten in star pattern70 lb-ft95 Nm
- Transmission Drain PlugUse new crush washer if equipped22 lb-ft30 Nm
- Transmission Filter BoltsIf equipped with bolted filter6 lb-ft8 Nm
- Transmission Pan BoltsTighten in criss-cross pattern9 lb-ft12 Nm
Transmission Flush5 specs
- Drain PlugUse new washer24 lb-ft33 Nm
- Fill Plug24 lb-ft33 Nm
- Flywheel BoltsOften TTY, tighten in star pattern70 lb-ft95 Nm
- Transmission Drain PlugUse new crush washer if equipped22 lb-ft30 Nm
- Transmission Pan BoltsTighten in criss-cross pattern9 lb-ft12 Nm
Transmission Input Shaft Bearing5 specs
- Drain PlugUse new washer24 lb-ft33 Nm
- Fill Plug24 lb-ft33 Nm
- Flywheel BoltsOften TTY, tighten in star pattern70 lb-ft95 Nm
- Transmission Drain PlugUse new crush washer if equipped22 lb-ft30 Nm
- Transmission Pan BoltsTighten in criss-cross pattern9 lb-ft12 Nm
Transmission Oil Cooler12 specs
- Coolant Drain Plug11 lb-ft15 Nm
- Drain PetcockHand tight5 lb-ft7 Nm
- Drain PlugUse new washer24 lb-ft33 Nm
- Fan Bolts8 lb-ft11 Nm
- Fill Plug24 lb-ft33 Nm
- Flywheel BoltsOften TTY, tighten in star pattern70 lb-ft95 Nm
- Hose Clamps2 lb-ft3 Nm
- Pump BoltsTorque in sequence17 lb-ft23 Nm
- Thermostat Housing Bolt11 lb-ft15 Nm
- Transmission Drain PlugUse new crush washer if equipped22 lb-ft30 Nm
- Transmission Pan BoltsTighten in criss-cross pattern9 lb-ft12 Nm
- Water Pump BoltsTighten in criss-cross pattern18 lb-ft25 Nm
Transmission Output Shaft Bearing5 specs
- Drain PlugUse new washer24 lb-ft33 Nm
- Fill Plug24 lb-ft33 Nm
- Flywheel BoltsOften TTY, tighten in star pattern70 lb-ft95 Nm
- Transmission Drain PlugUse new crush washer if equipped22 lb-ft30 Nm
- Transmission Pan BoltsTighten in criss-cross pattern9 lb-ft12 Nm
Transmission Pan Gasket5 specs
- Drain PlugUse new washer24 lb-ft33 Nm
- Fill Plug24 lb-ft33 Nm
- Flywheel BoltsOften TTY, tighten in star pattern70 lb-ft95 Nm
- Transmission Drain PlugUse new crush washer if equipped22 lb-ft30 Nm
- Transmission Pan BoltsTighten in criss-cross pattern9 lb-ft12 Nm
Transmission R&R - Automatic5 specs
- Drain PlugUse new washer24 lb-ft33 Nm
- Fill Plug24 lb-ft33 Nm
- Flywheel BoltsOften TTY, tighten in star pattern70 lb-ft95 Nm
- Transmission Drain PlugUse new crush washer if equipped22 lb-ft30 Nm
- Transmission Pan BoltsTighten in criss-cross pattern9 lb-ft12 Nm
Transmission R&R - Manual5 specs
- Drain PlugUse new washer24 lb-ft33 Nm
- Fill Plug24 lb-ft33 Nm
- Flywheel BoltsOften TTY, tighten in star pattern70 lb-ft95 Nm
- Transmission Drain PlugUse new crush washer if equipped22 lb-ft30 Nm
- Transmission Pan BoltsTighten in criss-cross pattern9 lb-ft12 Nm
Transmission Range Sensor5 specs
- Drain PlugUse new washer24 lb-ft33 Nm
- Fill Plug24 lb-ft33 Nm
- Flywheel BoltsOften TTY, tighten in star pattern70 lb-ft95 Nm
- Transmission Drain PlugUse new crush washer if equipped22 lb-ft30 Nm
- Transmission Pan BoltsTighten in criss-cross pattern9 lb-ft12 Nm
Transmission Rebuild - Automatic5 specs
- Drain PlugUse new washer24 lb-ft33 Nm
- Fill Plug24 lb-ft33 Nm
- Flywheel BoltsOften TTY, tighten in star pattern70 lb-ft95 Nm
- Transmission Drain PlugUse new crush washer if equipped22 lb-ft30 Nm
- Transmission Pan BoltsTighten in criss-cross pattern9 lb-ft12 Nm
Transmission Rebuild - Manual5 specs
- Drain PlugUse new washer24 lb-ft33 Nm
- Fill Plug24 lb-ft33 Nm
- Flywheel BoltsOften TTY, tighten in star pattern70 lb-ft95 Nm
- Transmission Drain PlugUse new crush washer if equipped22 lb-ft30 Nm
- Transmission Pan BoltsTighten in criss-cross pattern9 lb-ft12 Nm
Transmission Speed Sensor - Input5 specs
- Drain PlugUse new washer24 lb-ft33 Nm
- Fill Plug24 lb-ft33 Nm
- Flywheel BoltsOften TTY, tighten in star pattern70 lb-ft95 Nm
- Transmission Drain PlugUse new crush washer if equipped22 lb-ft30 Nm
- Transmission Pan BoltsTighten in criss-cross pattern9 lb-ft12 Nm
Transmission Speed Sensor - Output5 specs
- Drain PlugUse new washer24 lb-ft33 Nm
- Fill Plug24 lb-ft33 Nm
- Flywheel BoltsOften TTY, tighten in star pattern70 lb-ft95 Nm
- Transmission Drain PlugUse new crush washer if equipped22 lb-ft30 Nm
- Transmission Pan BoltsTighten in criss-cross pattern9 lb-ft12 Nm
Valve Body5 specs
- Drain PlugUse new washer24 lb-ft33 Nm
- Fill Plug24 lb-ft33 Nm
- Flywheel BoltsOften TTY, tighten in star pattern70 lb-ft95 Nm
- Transmission Drain PlugUse new crush washer if equipped22 lb-ft30 Nm
- Transmission Pan BoltsTighten in criss-cross pattern9 lb-ft12 Nm

Exhaust

Catalytic Converter - California5 specs
- Exhaust Flange BoltApply anti-seize33 lb-ft45 Nm
- Hanger Bolts14 lb-ft19 Nm
- Heat Shield Bolts7 lb-ft10 Nm
- Manifold NutsApply anti-seize24 lb-ft33 Nm
- O2 SensorApply anti-seize to threads only33 lb-ft45 Nm
Catalytic Converter - Direct Fit5 specs
- Exhaust Flange BoltApply anti-seize33 lb-ft45 Nm
- Hanger Bolts14 lb-ft19 Nm
- Heat Shield Bolts7 lb-ft10 Nm
- Manifold NutsApply anti-seize24 lb-ft33 Nm
- O2 SensorApply anti-seize to threads only33 lb-ft45 Nm
Catalytic Converter - Universal5 specs
- Exhaust Flange BoltApply anti-seize33 lb-ft45 Nm
- Hanger Bolts14 lb-ft19 Nm
- Heat Shield Bolts7 lb-ft10 Nm
- Manifold NutsApply anti-seize24 lb-ft33 Nm
- O2 SensorApply anti-seize to threads only33 lb-ft45 Nm
Downpipe5 specs
- Exhaust Flange BoltApply anti-seize33 lb-ft45 Nm
- Hanger Bolts14 lb-ft19 Nm
- Heat Shield Bolts7 lb-ft10 Nm
- Manifold NutsApply anti-seize24 lb-ft33 Nm
- O2 SensorApply anti-seize to threads only33 lb-ft45 Nm
EGR Tube5 specs
- Exhaust Flange BoltApply anti-seize33 lb-ft45 Nm
- Hanger Bolts14 lb-ft19 Nm
- Heat Shield Bolts7 lb-ft10 Nm
- Manifold NutsApply anti-seize24 lb-ft33 Nm
- O2 SensorApply anti-seize to threads only33 lb-ft45 Nm
EGR Valve6 specs
- EGR Tube Fitting26 lb-ft35 Nm
- EGR Valve Bolts18 lb-ft25 Nm
- Hanger Bolts14 lb-ft19 Nm
- Heat Shield Bolts10 lb-ft14 Nm
- Manifold NutsApply anti-seize24 lb-ft33 Nm
- O2 SensorApply anti-seize to threads33 lb-ft45 Nm
Exhaust Clamp5 specs
- Exhaust Flange BoltApply anti-seize33 lb-ft45 Nm
- Hanger Bolts14 lb-ft19 Nm
- Heat Shield Bolts7 lb-ft10 Nm
- Manifold NutsApply anti-seize24 lb-ft33 Nm
- O2 SensorApply anti-seize to threads only33 lb-ft45 Nm
Exhaust Gasket - Front5 specs
- Exhaust Flange BoltApply anti-seize33 lb-ft45 Nm
- Hanger Bolts14 lb-ft19 Nm
- Heat Shield Bolts7 lb-ft10 Nm
- Manifold NutsApply anti-seize24 lb-ft33 Nm
- O2 SensorApply anti-seize to threads only33 lb-ft45 Nm
Exhaust Gasket - Rear5 specs
- Exhaust Flange BoltApply anti-seize33 lb-ft45 Nm
- Hanger Bolts14 lb-ft19 Nm
- Heat Shield Bolts7 lb-ft10 Nm
- Manifold NutsApply anti-seize24 lb-ft33 Nm
- O2 SensorApply anti-seize to threads only33 lb-ft45 Nm
Exhaust Hangers5 specs
- Exhaust Flange BoltApply anti-seize33 lb-ft45 Nm
- Hanger Bolts14 lb-ft19 Nm
- Heat Shield Bolts7 lb-ft10 Nm
- Manifold NutsApply anti-seize24 lb-ft33 Nm
- O2 SensorApply anti-seize to threads only33 lb-ft45 Nm
Exhaust Manifold Studs5 specs
- Exhaust Flange BoltApply anti-seize33 lb-ft45 Nm
- Hanger Bolts14 lb-ft19 Nm
- Heat Shield Bolts7 lb-ft10 Nm
- Manifold NutsApply anti-seize24 lb-ft33 Nm
- O2 SensorApply anti-seize to threads only33 lb-ft45 Nm
Exhaust Pipe - Rear Section5 specs
- Exhaust Flange BoltApply anti-seize33 lb-ft45 Nm
- Hanger Bolts14 lb-ft19 Nm
- Heat Shield Bolts7 lb-ft10 Nm
- Manifold NutsApply anti-seize24 lb-ft33 Nm
- O2 SensorApply anti-seize to threads only33 lb-ft45 Nm
Exhaust Tip5 specs
- Exhaust Flange BoltApply anti-seize33 lb-ft45 Nm
- Hanger Bolts14 lb-ft19 Nm
- Heat Shield Bolts7 lb-ft10 Nm
- Manifold NutsApply anti-seize24 lb-ft33 Nm
- O2 SensorApply anti-seize to threads only33 lb-ft45 Nm
Flex Pipe5 specs
- Exhaust Clamps41 lb-ft55 Nm
- Hanger Bolts14 lb-ft19 Nm
- Heat Shield Bolts10 lb-ft14 Nm
- Manifold NutsApply anti-seize24 lb-ft33 Nm
- O2 SensorApply anti-seize to threads33 lb-ft45 Nm
Front Pipe5 specs
- Exhaust Flange BoltApply anti-seize33 lb-ft45 Nm
- Hanger Bolts14 lb-ft19 Nm
- Heat Shield Bolts7 lb-ft10 Nm
- Manifold NutsApply anti-seize24 lb-ft33 Nm
- O2 SensorApply anti-seize to threads only33 lb-ft45 Nm
Intermediate Pipe5 specs
- Exhaust Flange BoltApply anti-seize33 lb-ft45 Nm
- Hanger Bolts14 lb-ft19 Nm
- Heat Shield Bolts7 lb-ft10 Nm
- Manifold NutsApply anti-seize24 lb-ft33 Nm
- O2 SensorApply anti-seize to threads only33 lb-ft45 Nm
Muffler2 specs
- Hanger Bracket Bolts18 lb-ft25 Nm
- Muffler Clamps41 lb-ft55 Nm
O2 Sensor - Downstream5 specs
- Exhaust Flange BoltApply anti-seize33 lb-ft45 Nm
- Hanger Bolts14 lb-ft19 Nm
- Heat Shield Bolts7 lb-ft10 Nm
- Manifold NutsApply anti-seize24 lb-ft33 Nm
- O2 SensorApply anti-seize to threads only33 lb-ft45 Nm
O2 Sensor - Upstream5 specs
- Exhaust Flange BoltApply anti-seize33 lb-ft45 Nm
- Hanger Bolts14 lb-ft19 Nm
- Heat Shield Bolts7 lb-ft10 Nm
- Manifold NutsApply anti-seize24 lb-ft33 Nm
- O2 SensorApply anti-seize to threads only33 lb-ft45 Nm
O2 Sensors - All5 specs
- Exhaust Flange BoltApply anti-seize33 lb-ft45 Nm
- Hanger Bolts14 lb-ft19 Nm
- Heat Shield Bolts7 lb-ft10 Nm
- Manifold NutsApply anti-seize24 lb-ft33 Nm
- O2 SensorApply anti-seize to threads only33 lb-ft45 Nm
Resonator5 specs
- Exhaust Clamps41 lb-ft55 Nm
- Hanger Bolts14 lb-ft19 Nm
- Heat Shield Bolts10 lb-ft14 Nm
- Manifold NutsApply anti-seize24 lb-ft33 Nm
- O2 SensorApply anti-seize to threads33 lb-ft45 Nm
Tail Pipe5 specs
- Exhaust Flange BoltApply anti-seize33 lb-ft45 Nm
- Hanger Bolts14 lb-ft19 Nm
- Heat Shield Bolts7 lb-ft10 Nm
- Manifold NutsApply anti-seize24 lb-ft33 Nm
- O2 SensorApply anti-seize to threads only33 lb-ft45 Nm

Heating and A/C

AC Accumulator6 specs
- AC Line FittingsUse new O-rings, add PAG oil15 lb-ft20 Nm
- Blower Motor Mounting Screw3 lb-ft4 Nm
- Compressor Bolts24 lb-ft33 Nm
- Duct Clips2 lb-ft3 Nm
- Hose Clamps2 lb-ft3 Nm
- Mounting Bracket Bolts17 lb-ft23 Nm
AC Clutch Coil6 specs
- AC Line FittingsUse new O-rings, add PAG oil15 lb-ft20 Nm
- Blower Motor Mounting Screw3 lb-ft4 Nm
- Compressor Bolts24 lb-ft33 Nm
- Duct Clips2 lb-ft3 Nm
- Hose Clamps2 lb-ft3 Nm
- Mounting Bracket Bolts17 lb-ft23 Nm
AC Compressor3 specs
- AC Compressor Bolts18 lb-ft25 Nm
- AC Line FittingsUse new O-rings, add PAG oil15 lb-ft20 Nm
- Clutch Connector Bolt6 lb-ft8 Nm
AC Compressor Clutch6 specs
- AC Line FittingsUse new O-rings, add PAG oil15 lb-ft20 Nm
- Blower Motor Mounting Screw3 lb-ft4 Nm
- Compressor Bolts24 lb-ft33 Nm
- Duct Clips2 lb-ft3 Nm
- Hose Clamps2 lb-ft3 Nm
- Mounting Bracket Bolts17 lb-ft23 Nm
AC Compressor Oil Add6 specs
- AC Line FittingsUse new O-rings, add PAG oil15 lb-ft20 Nm
- Blower Motor Mounting Screw3 lb-ft4 Nm
- Compressor Bolts24 lb-ft33 Nm
- Duct Clips2 lb-ft3 Nm
- Hose Clamps2 lb-ft3 Nm
- Mounting Bracket Bolts17 lb-ft23 Nm
AC Condenser2 specs
- AC Line FittingsUse new O-rings15 lb-ft20 Nm
- Condenser Mounting Bolts9 lb-ft12 Nm
AC Evaporator7 specs
- AC Line FittingsUse new O-rings, add PAG oil15 lb-ft20 Nm
- Blower Motor Mounting Screw5 lb-ft7 Nm
- Compressor Bolts24 lb-ft33 Nm
- Duct Clips2 lb-ft3 Nm
- Evaporator Case Screws4 lb-ft5 Nm
- Expansion Valve7 lb-ft10 Nm
- Mounting Bracket Bolts17 lb-ft23 Nm
AC Expansion Valve (TXV)6 specs
- AC Line FittingsUse new O-rings, add PAG oil15 lb-ft20 Nm
- Blower Motor Mounting Screw5 lb-ft7 Nm
- Compressor Bolts24 lb-ft33 Nm
- Duct Clips2 lb-ft3 Nm
- Expansion Valve7 lb-ft10 Nm
- Mounting Bracket Bolts17 lb-ft23 Nm
AC High Pressure Switch6 specs
- AC Line FittingsUse new O-rings, add PAG oil15 lb-ft20 Nm
- Blower Motor Mounting Screw3 lb-ft4 Nm
- Compressor Bolts24 lb-ft33 Nm
- Duct Clips2 lb-ft3 Nm
- Hose Clamps2 lb-ft3 Nm
- Mounting Bracket Bolts17 lb-ft23 Nm
AC Hose - High Side6 specs
- AC Line FittingsUse new O-rings, add PAG oil15 lb-ft20 Nm
- Blower Motor Mounting Screw3 lb-ft4 Nm
- Compressor Bolts24 lb-ft33 Nm
- Duct Clips2 lb-ft3 Nm
- Hose Clamps2 lb-ft3 Nm
- Mounting Bracket Bolts17 lb-ft23 Nm
AC Hose - Low Side6 specs
- AC Line FittingsUse new O-rings, add PAG oil15 lb-ft20 Nm
- Blower Motor Mounting Screw3 lb-ft4 Nm
- Compressor Bolts24 lb-ft33 Nm
- Duct Clips2 lb-ft3 Nm
- Hose Clamps2 lb-ft3 Nm
- Mounting Bracket Bolts17 lb-ft23 Nm
AC Hose Assembly6 specs
- AC Line FittingsUse new O-rings, add PAG oil15 lb-ft20 Nm
- Blower Motor Mounting Screw3 lb-ft4 Nm
- Compressor Bolts24 lb-ft33 Nm
- Duct Clips2 lb-ft3 Nm
- Hose Clamps2 lb-ft3 Nm
- Mounting Bracket Bolts17 lb-ft23 Nm
AC Low Pressure Switch6 specs
- AC Line FittingsUse new O-rings, add PAG oil15 lb-ft20 Nm
- Blower Motor Mounting Screw3 lb-ft4 Nm
- Compressor Bolts24 lb-ft33 Nm
- Duct Clips2 lb-ft3 Nm
- Hose Clamps2 lb-ft3 Nm
- Mounting Bracket Bolts17 lb-ft23 Nm
AC Orifice Tube6 specs
- AC Line FittingsUse new O-rings, add PAG oil15 lb-ft20 Nm
- Blower Motor Mounting Screw3 lb-ft4 Nm
- Compressor Bolts24 lb-ft33 Nm
- Duct Clips2 lb-ft3 Nm
- Hose Clamps2 lb-ft3 Nm
- Mounting Bracket Bolts17 lb-ft23 Nm
AC Pressure Sensor6 specs
- AC Line FittingsUse new O-rings, add PAG oil15 lb-ft20 Nm
- Blower Motor Mounting Screw3 lb-ft4 Nm
- Compressor Bolts24 lb-ft33 Nm
- Duct Clips2 lb-ft3 Nm
- Hose Clamps2 lb-ft3 Nm
- Mounting Bracket Bolts17 lb-ft23 Nm
AC Receiver/Drier6 specs
- AC Line FittingsUse new O-rings, add PAG oil15 lb-ft20 Nm
- Blower Motor Mounting Screw5 lb-ft7 Nm
- Compressor Bolts24 lb-ft33 Nm
- Duct Clips2 lb-ft3 Nm
- Mounting Bracket Bolts17 lb-ft23 Nm
- Receiver Drier Bolts7 lb-ft10 Nm
AC Recharge6 specs
- AC Line FittingsUse new O-rings, add PAG oil15 lb-ft20 Nm
- Blower Motor Mounting Screw3 lb-ft4 Nm
- Compressor Bolts24 lb-ft33 Nm
- Duct Clips2 lb-ft3 Nm
- Hose Clamps2 lb-ft3 Nm
- Mounting Bracket Bolts17 lb-ft23 Nm
Blend Door Actuator5 specs
- Actuator Screws2 lb-ft3 Nm
- Blower Motor Mounting Screw5 lb-ft7 Nm
- Compressor Bolts24 lb-ft33 Nm
- Duct Clips2 lb-ft3 Nm
- Mounting Bracket Bolts17 lb-ft23 Nm
Cabin Air Filter4 specs
- Compressor Bolts24 lb-ft32 Nm
- Connector Bolts5 lb-ft7 Nm
- Filter Cover ClipsTool-free on most2 lb-ft3 Nm
- Glove Box Screws3 lb-ft4 Nm
Climate Control Module6 specs
- AC Line FittingsUse new O-rings, add PAG oil15 lb-ft20 Nm
- Blower Motor Mounting Screw3 lb-ft4 Nm
- Compressor Bolts24 lb-ft33 Nm
- Duct Clips2 lb-ft3 Nm
- Hose Clamps2 lb-ft3 Nm
- Mounting Bracket Bolts17 lb-ft23 Nm
HVAC Control Panel6 specs
- AC Line FittingsUse new O-rings, add PAG oil15 lb-ft20 Nm
- Blower Motor Mounting Screw3 lb-ft4 Nm
- Compressor Bolts24 lb-ft33 Nm
- Duct Clips2 lb-ft3 Nm
- Hose Clamps2 lb-ft3 Nm
- Mounting Bracket Bolts17 lb-ft23 Nm
Mode Door Actuator6 specs
- AC Line FittingsUse new O-rings, add PAG oil15 lb-ft20 Nm
- Blower Motor Mounting Screw3 lb-ft4 Nm
- Compressor Bolts24 lb-ft33 Nm
- Duct Clips2 lb-ft3 Nm
- Hose Clamps2 lb-ft3 Nm
- Mounting Bracket Bolts17 lb-ft23 Nm
Recirculation Door Actuator6 specs
- AC Line FittingsUse new O-rings, add PAG oil15 lb-ft20 Nm
- Blower Motor Mounting Screw3 lb-ft4 Nm
- Compressor Bolts24 lb-ft33 Nm
- Duct Clips2 lb-ft3 Nm
- Hose Clamps2 lb-ft3 Nm
- Mounting Bracket Bolts17 lb-ft23 Nm

Body

Bumper Cover - Front8 specs
- Bumper Cover Bolts7 lb-ft10 Nm
- Fender Liner Screws2 lb-ft3 Nm
- Grille Clips4 lb-ft5 Nm
- Hinge Bolts19 lb-ft26 Nm
- Latch Bolts10 lb-ft14 Nm
- Panel Bolts10 lb-ft14 Nm
- Striker Bolts24 lb-ft33 Nm
- Trim ClipsReplace if broken2 lb-ft3 Nm
Bumper Cover - Rear7 specs
- Bumper Cover Bolts7 lb-ft10 Nm
- Hinge Bolts19 lb-ft26 Nm
- Latch Bolts10 lb-ft14 Nm
- Panel Bolts10 lb-ft14 Nm
- Striker Bolts24 lb-ft33 Nm
- Trim ClipsReplace if broken2 lb-ft3 Nm
- Trunk Liner Screws2 lb-ft3 Nm
Bumper Reinforcement - Front8 specs
- Body Panel Bolts18 lb-ft25 Nm
- Bumper Cover Bolts7 lb-ft10 Nm
- Door Hinge Bolts22 lb-ft30 Nm
- Hinge Bolts19 lb-ft26 Nm
- Latch Bolts10 lb-ft14 Nm
- Panel Bolts10 lb-ft14 Nm
- Striker Bolts24 lb-ft33 Nm
- Trim ClipsReplace if broken2 lb-ft3 Nm
Bumper Reinforcement - Rear8 specs
- Body Panel Bolts18 lb-ft25 Nm
- Bumper Cover Bolts7 lb-ft10 Nm
- Door Hinge Bolts22 lb-ft30 Nm
- Hinge Bolts19 lb-ft26 Nm
- Latch Bolts10 lb-ft14 Nm
- Panel Bolts10 lb-ft14 Nm
- Striker Bolts24 lb-ft33 Nm
- Trim ClipsReplace if broken2 lb-ft3 Nm
Door Check/Stop8 specs
- Body Panel Bolts18 lb-ft25 Nm
- Bumper Cover Bolts7 lb-ft10 Nm
- Door Hinge Bolts22 lb-ft30 Nm
- Hinge Bolts19 lb-ft26 Nm
- Latch Bolts10 lb-ft14 Nm
- Panel Bolts10 lb-ft14 Nm
- Striker Bolts24 lb-ft33 Nm
- Trim ClipsReplace if broken2 lb-ft3 Nm
Door Glass8 specs
- Body Panel Bolts18 lb-ft25 Nm
- Bumper Cover Bolts7 lb-ft10 Nm
- Door Hinge Bolts22 lb-ft30 Nm
- Hinge Bolts19 lb-ft26 Nm
- Latch Bolts10 lb-ft14 Nm
- Panel Bolts10 lb-ft14 Nm
- Striker Bolts24 lb-ft33 Nm
- Trim ClipsReplace if broken2 lb-ft3 Nm
Door Handle - Exterior7 specs
- Handle Mounting Bolts6 lb-ft8 Nm
- Hinge Bolts19 lb-ft26 Nm
- Latch Bolts10 lb-ft14 Nm
- Lock Rod Clips4 lb-ft5 Nm
- Panel Bolts10 lb-ft14 Nm
- Striker Bolts24 lb-ft33 Nm
- Trim ClipsReplace if broken2 lb-ft3 Nm
Door Handle - Interior7 specs
- Cable Clips4 lb-ft5 Nm
- Handle Screws2 lb-ft3 Nm
- Hinge Bolts19 lb-ft26 Nm
- Latch Bolts10 lb-ft14 Nm
- Panel Bolts10 lb-ft14 Nm
- Striker Bolts24 lb-ft33 Nm
- Trim ClipsReplace if broken2 lb-ft3 Nm
Door Hinge6 specs
- Door Hinge Bolts22 lb-ft30 Nm
- Hinge Bolts19 lb-ft26 Nm
- Latch Bolts10 lb-ft14 Nm
- Panel Bolts10 lb-ft14 Nm
- Striker Bolts24 lb-ft33 Nm
- Trim ClipsReplace if broken2 lb-ft3 Nm
Door Shell8 specs
- Body Panel Bolts18 lb-ft25 Nm
- Bumper Cover Bolts7 lb-ft10 Nm
- Door Hinge Bolts22 lb-ft30 Nm
- Hinge Bolts19 lb-ft26 Nm
- Latch Bolts10 lb-ft14 Nm
- Panel Bolts10 lb-ft14 Nm
- Striker Bolts24 lb-ft33 Nm
- Trim ClipsReplace if broken2 lb-ft3 Nm
Door Skin8 specs
- Body Panel Bolts18 lb-ft25 Nm
- Bumper Cover Bolts7 lb-ft10 Nm
- Door Hinge Bolts22 lb-ft30 Nm
- Hinge Bolts19 lb-ft26 Nm
- Latch Bolts10 lb-ft14 Nm
- Panel Bolts10 lb-ft14 Nm
- Striker Bolts24 lb-ft33 Nm
- Trim ClipsReplace if broken2 lb-ft3 Nm
Door Weatherstrip8 specs
- Body Panel Bolts18 lb-ft25 Nm
- Bumper Cover Bolts7 lb-ft10 Nm
- Door Hinge Bolts22 lb-ft30 Nm
- Hinge Bolts19 lb-ft26 Nm
- Latch Bolts10 lb-ft14 Nm
- Panel Bolts10 lb-ft14 Nm
- Striker Bolts24 lb-ft33 Nm
- Trim ClipsReplace if broken2 lb-ft3 Nm
Fender8 specs
- Fender Bolts9 lb-ft12 Nm
- Fender Liner Screws2 lb-ft3 Nm
- Hinge Bolts19 lb-ft26 Nm
- Hood Hinge Bolts18 lb-ft25 Nm
- Latch Bolts10 lb-ft14 Nm
- Panel Bolts10 lb-ft14 Nm
- Striker Bolts24 lb-ft33 Nm
- Trim ClipsReplace if broken2 lb-ft3 Nm
Fender Liner8 specs
- Body Panel Bolts18 lb-ft25 Nm
- Bumper Cover Bolts7 lb-ft10 Nm
- Door Hinge Bolts22 lb-ft30 Nm
- Hinge Bolts19 lb-ft26 Nm
- Latch Bolts10 lb-ft14 Nm
- Panel Bolts10 lb-ft14 Nm
- Striker Bolts24 lb-ft33 Nm
- Trim ClipsReplace if broken2 lb-ft3 Nm
Grille7 specs
- Clips4 lb-ft5 Nm
- Grille Mounting Screws2 lb-ft3 Nm
- Hinge Bolts19 lb-ft26 Nm
- Latch Bolts10 lb-ft14 Nm
- Panel Bolts10 lb-ft14 Nm
- Striker Bolts24 lb-ft33 Nm
- Trim ClipsReplace if broken2 lb-ft3 Nm
Hood8 specs
- Hinge Bolts19 lb-ft26 Nm
- Hood Hinge Bolts18 lb-ft25 Nm
- Hood Latch Bolts9 lb-ft12 Nm
- Hood Strut Bolts7 lb-ft10 Nm
- Latch Bolts10 lb-ft14 Nm
- Panel Bolts10 lb-ft14 Nm
- Striker Bolts24 lb-ft33 Nm
- Trim ClipsReplace if broken2 lb-ft3 Nm
Hood Hinge8 specs
- Body Panel Bolts18 lb-ft25 Nm
- Bumper Cover Bolts7 lb-ft10 Nm
- Door Hinge Bolts22 lb-ft30 Nm
- Hinge Bolts19 lb-ft26 Nm
- Latch Bolts10 lb-ft14 Nm
- Panel Bolts10 lb-ft14 Nm
- Striker Bolts24 lb-ft33 Nm
- Trim ClipsReplace if broken2 lb-ft3 Nm
Hood Latch7 specs
- Cable Clips4 lb-ft5 Nm
- Hinge Bolts19 lb-ft26 Nm
- Hood Latch Bolts9 lb-ft12 Nm
- Latch Bolts10 lb-ft14 Nm
- Panel Bolts10 lb-ft14 Nm
- Striker Bolts24 lb-ft33 Nm
- Trim ClipsReplace if broken2 lb-ft3 Nm
Hood Release Cable8 specs
- Body Panel Bolts18 lb-ft25 Nm
- Bumper Cover Bolts7 lb-ft10 Nm
- Door Hinge Bolts22 lb-ft30 Nm
- Hinge Bolts19 lb-ft26 Nm
- Latch Bolts10 lb-ft14 Nm
- Panel Bolts10 lb-ft14 Nm
- Striker Bolts24 lb-ft33 Nm
- Trim ClipsReplace if broken2 lb-ft3 Nm
Hood Strut8 specs
- Body Panel Bolts18 lb-ft25 Nm
- Bumper Cover Bolts7 lb-ft10 Nm
- Door Hinge Bolts22 lb-ft30 Nm
- Hinge Bolts19 lb-ft26 Nm
- Latch Bolts10 lb-ft14 Nm
- Panel Bolts10 lb-ft14 Nm
- Striker Bolts24 lb-ft33 Nm
- Trim ClipsReplace if broken2 lb-ft3 Nm
Quarter Glass8 specs
- Body Panel Bolts18 lb-ft25 Nm
- Bumper Cover Bolts7 lb-ft10 Nm
- Door Hinge Bolts22 lb-ft30 Nm
- Hinge Bolts19 lb-ft26 Nm
- Latch Bolts10 lb-ft14 Nm
- Panel Bolts10 lb-ft14 Nm
- Striker Bolts24 lb-ft33 Nm
- Trim ClipsReplace if broken2 lb-ft3 Nm
Quarter Panel8 specs
- Body Panel Bolts18 lb-ft25 Nm
- Bumper Cover Bolts7 lb-ft10 Nm
- Door Hinge Bolts22 lb-ft30 Nm
- Hinge Bolts19 lb-ft26 Nm
- Latch Bolts10 lb-ft14 Nm
- Panel Bolts10 lb-ft14 Nm
- Striker Bolts24 lb-ft33 Nm
- Trim ClipsReplace if broken2 lb-ft3 Nm
Rear Window8 specs
- Body Panel Bolts18 lb-ft25 Nm
- Bumper Cover Bolts7 lb-ft10 Nm
- Door Hinge Bolts22 lb-ft30 Nm
- Hinge Bolts19 lb-ft26 Nm
- Latch Bolts10 lb-ft14 Nm
- Panel Bolts10 lb-ft14 Nm
- Striker Bolts24 lb-ft33 Nm
- Trim ClipsReplace if broken2 lb-ft3 Nm
Rocker Panel8 specs
- Body Panel Bolts18 lb-ft25 Nm
- Bumper Cover Bolts7 lb-ft10 Nm
- Door Hinge Bolts22 lb-ft30 Nm
- Hinge Bolts19 lb-ft26 Nm
- Latch Bolts10 lb-ft14 Nm
- Panel Bolts10 lb-ft14 Nm
- Striker Bolts24 lb-ft33 Nm
- Trim ClipsReplace if broken2 lb-ft3 Nm
Side Mirror Glass8 specs
- Body Panel Bolts18 lb-ft25 Nm
- Bumper Cover Bolts7 lb-ft10 Nm
- Door Hinge Bolts22 lb-ft30 Nm
- Hinge Bolts19 lb-ft26 Nm
- Latch Bolts10 lb-ft14 Nm
- Panel Bolts10 lb-ft14 Nm
- Striker Bolts24 lb-ft33 Nm
- Trim ClipsReplace if broken2 lb-ft3 Nm
Trunk Hinge8 specs
- Body Panel Bolts18 lb-ft25 Nm
- Bumper Cover Bolts7 lb-ft10 Nm
- Door Hinge Bolts22 lb-ft30 Nm
- Hinge Bolts19 lb-ft26 Nm
- Latch Bolts10 lb-ft14 Nm
- Panel Bolts10 lb-ft14 Nm
- Striker Bolts24 lb-ft33 Nm
- Trim ClipsReplace if broken2 lb-ft3 Nm
Trunk Latch8 specs
- Body Panel Bolts18 lb-ft25 Nm
- Bumper Cover Bolts7 lb-ft10 Nm
- Door Hinge Bolts22 lb-ft30 Nm
- Hinge Bolts19 lb-ft26 Nm
- Latch Bolts10 lb-ft14 Nm
- Panel Bolts10 lb-ft14 Nm
- Striker Bolts24 lb-ft33 Nm
- Trim ClipsReplace if broken2 lb-ft3 Nm
Trunk Lid7 specs
- Hinge Bolts19 lb-ft26 Nm
- Latch Bolts10 lb-ft14 Nm
- Panel Bolts10 lb-ft14 Nm
- Striker Bolts24 lb-ft33 Nm
- Trim ClipsReplace if broken2 lb-ft3 Nm
- Trunk Hinge Bolts18 lb-ft25 Nm
- Trunk Latch Bolts9 lb-ft12 Nm
Trunk Strut8 specs
- Body Panel Bolts18 lb-ft25 Nm
- Bumper Cover Bolts7 lb-ft10 Nm
- Door Hinge Bolts22 lb-ft30 Nm
- Hinge Bolts19 lb-ft26 Nm
- Latch Bolts10 lb-ft14 Nm
- Panel Bolts10 lb-ft14 Nm
- Striker Bolts24 lb-ft33 Nm
- Trim ClipsReplace if broken2 lb-ft3 Nm
Windshield8 specs
- Body Panel Bolts18 lb-ft25 Nm
- Bumper Cover Bolts7 lb-ft10 Nm
- Door Hinge Bolts22 lb-ft30 Nm
- Hinge Bolts19 lb-ft26 Nm
- Latch Bolts10 lb-ft14 Nm
- Panel Bolts10 lb-ft14 Nm
- Striker Bolts24 lb-ft33 Nm
- Trim ClipsReplace if broken2 lb-ft3 Nm
Windshield Molding8 specs
- Body Panel Bolts18 lb-ft25 Nm
- Bumper Cover Bolts7 lb-ft10 Nm
- Door Hinge Bolts22 lb-ft30 Nm
- Hinge Bolts19 lb-ft26 Nm
- Latch Bolts10 lb-ft14 Nm
- Panel Bolts10 lb-ft14 Nm
- Striker Bolts24 lb-ft33 Nm
- Trim ClipsReplace if broken2 lb-ft3 Nm

Interior

Armrest4 specs
- Connector Bolts5 lb-ft7 Nm
- Dashboard Screws2 lb-ft3 Nm
- Seat Mounting BoltsSafety critical33 lb-ft45 Nm
- Trim Panel ClipsReplace if damaged1.5 lb-ft2 Nm
Carpet4 specs
- Connector Bolts5 lb-ft7 Nm
- Dashboard Screws2 lb-ft3 Nm
- Seat Mounting BoltsSafety critical33 lb-ft45 Nm
- Trim Panel ClipsReplace if damaged1.5 lb-ft2 Nm
Center Console3 specs
- Connector Bolts5 lb-ft7 Nm
- Console Screws2 lb-ft3 Nm
- Shifter Trim4 lb-ft5 Nm
Dash Pad4 specs
- Connector Bolts5 lb-ft7 Nm
- Dashboard Screws2 lb-ft3 Nm
- Seat Mounting BoltsSafety critical33 lb-ft45 Nm
- Trim Panel ClipsReplace if damaged1.5 lb-ft2 Nm
Dashboard4 specs
- Connector Bolts5 lb-ft7 Nm
- Dashboard Bolt9 lb-ft12 Nm
- Dashboard Screws2 lb-ft3 Nm
- Trim Panel ClipsReplace if damaged1.5 lb-ft2 Nm
Door Panel3 specs
- Connector Bolts5 lb-ft7 Nm
- Door Panel Screws1.5 lb-ft2 Nm
- Trim Panel ClipsReplace if damaged1.5 lb-ft2 Nm
Floor Mat Hooks4 specs
- Connector Bolts5 lb-ft7 Nm
- Dashboard Screws2 lb-ft3 Nm
- Seat Mounting BoltsSafety critical33 lb-ft45 Nm
- Trim Panel ClipsReplace if damaged1.5 lb-ft2 Nm
Glove Box3 specs
- Connector Bolts5 lb-ft7 Nm
- Glove Box Screws2 lb-ft3 Nm
- Hinge Screws1.5 lb-ft2 Nm
Glove Box Latch4 specs
- Connector Bolts5 lb-ft7 Nm
- Dashboard Screws2 lb-ft3 Nm
- Seat Mounting BoltsSafety critical33 lb-ft45 Nm
- Trim Panel ClipsReplace if damaged1.5 lb-ft2 Nm
Headliner4 specs
- Connector Bolts5 lb-ft7 Nm
- Dashboard Screws2 lb-ft3 Nm
- Seat Mounting BoltsSafety critical33 lb-ft45 Nm
- Trim Panel ClipsReplace if damaged1.5 lb-ft2 Nm
Pedal Pads4 specs
- Connector Bolts5 lb-ft7 Nm
- Dashboard Screws2 lb-ft3 Nm
- Seat Mounting BoltsSafety critical33 lb-ft45 Nm
- Trim Panel ClipsReplace if damaged1.5 lb-ft2 Nm
Rearview Mirror4 specs
- Connector Bolts5 lb-ft7 Nm
- Dashboard Screws2 lb-ft3 Nm
- Seat Mounting BoltsSafety critical33 lb-ft45 Nm
- Trim Panel ClipsReplace if damaged1.5 lb-ft2 Nm
Seat - Front4 specs
- Connector Bolts5 lb-ft7 Nm
- Electrical Connectors4 lb-ft5 Nm
- Seat Mounting BoltsSafety critical33 lb-ft45 Nm
- Seat Track Bolts33 lb-ft45 Nm
Seat - Rear3 specs
- Connector Bolts5 lb-ft7 Nm
- Seat Back Release11 lb-ft15 Nm
- Seat Mounting Bolts26 lb-ft35 Nm
Seat Belt4 specs
- Connector Bolts5 lb-ft7 Nm
- Dashboard Screws2 lb-ft3 Nm
- Seat Mounting BoltsSafety critical33 lb-ft45 Nm
- Trim Panel ClipsReplace if damaged1.5 lb-ft2 Nm
Seat Belt Buckle4 specs
- Connector Bolts5 lb-ft7 Nm
- Dashboard Screws2 lb-ft3 Nm
- Seat Mounting BoltsSafety critical33 lb-ft45 Nm
- Trim Panel ClipsReplace if damaged1.5 lb-ft2 Nm
Seat Belt Pretensioner4 specs
- Connector Bolts5 lb-ft7 Nm
- Dashboard Screws2 lb-ft3 Nm
- Seat Mounting BoltsSafety critical33 lb-ft45 Nm
- Trim Panel ClipsReplace if damaged1.5 lb-ft2 Nm
Seat Cover4 specs
- Connector Bolts5 lb-ft7 Nm
- Dashboard Screws2 lb-ft3 Nm
- Seat Mounting BoltsSafety critical33 lb-ft45 Nm
- Trim Panel ClipsReplace if damaged1.5 lb-ft2 Nm
Seat Foam4 specs
- Connector Bolts5 lb-ft7 Nm
- Dashboard Screws2 lb-ft3 Nm
- Seat Mounting BoltsSafety critical33 lb-ft45 Nm
- Trim Panel ClipsReplace if damaged1.5 lb-ft2 Nm
Seat Track4 specs
- Connector Bolts5 lb-ft7 Nm
- Dashboard Screws2 lb-ft3 Nm
- Seat Mounting BoltsSafety critical33 lb-ft45 Nm
- Trim Panel ClipsReplace if damaged1.5 lb-ft2 Nm
Shifter Boot4 specs
- Connector Bolts5 lb-ft7 Nm
- Dashboard Screws2 lb-ft3 Nm
- Seat Mounting BoltsSafety critical33 lb-ft45 Nm
- Trim Panel ClipsReplace if damaged1.5 lb-ft2 Nm
Shifter Knob4 specs
- Connector Bolts5 lb-ft7 Nm
- Dashboard Screws2 lb-ft3 Nm
- Seat Mounting BoltsSafety critical33 lb-ft45 Nm
- Trim Panel ClipsReplace if damaged1.5 lb-ft2 Nm
Steering Wheel Cover4 specs
- Connector Bolts5 lb-ft7 Nm
- Dashboard ScrewsVerify sequence with the service manual2 lb-ft3 Nm
- Seat Mounting BoltsSafety critical. Verify sequence with the service manual33 lb-ft45 Nm
- Trim Panel ClipsReplace if damaged. Verify sequence with the service manual1.5 lb-ft2 Nm
Sun Visor2 specs
- Connector Bolts5 lb-ft7 Nm
- Visor Mounting Screws2 lb-ft3 Nm

Torque is shown in lb-ft with Nm below it. Where a step says to turn, tighten the listed angle after the torque step before it. Use new bolts where the note says so.

Need labor times, fluids or repair steps for this car? See it on the Open Labor Project