2022 Hyundai Elantra torque specs

2.0L I4

Change vehicle

Most looked up

Lug nuts80 lb-ft108 Nm
Oil drain plug27 lb-ft37 Nm
Spark plugs15 lb-ft20 Nm
Front caliper bracket bolts88 lb-ft120 Nm
Rear caliper bracket bolts74 lb-ft100 Nm
Front axle nut184 lb-ft250 Nm
Outer tie rod end nut40 lb-ft54 Nm

Maintenance

AC System Diagnosis2 specs
- AC Line FittingsNew O-rings15 lb-ft20 Nm
- Connector Bolts5 lb-ft7 Nm
Air Filter4 specs
- Air Box Clips4 lb-ft5 Nm
- Intake Tube Clamp3 lb-ft4 Nm
- MAF Sensor Screws3 lb-ft4 Nm
- Mass Air Flow Sensor Screws2 lb-ft3 Nm
Battery Test4 specs
- Battery Hold-Down BoltDo not overtighten8 lb-ft11 Nm
- Battery Terminal BoltsClean terminals5 lb-ft7 Nm
- Connector Bolts5 lb-ft7 Nm
- Ground Cable Bolt10 lb-ft14 Nm
Charging System Test1 spec
- Connector Bolts5 lb-ft7 Nm
Check Engine Light Diagnosis1 spec
- Connector Bolts5 lb-ft7 Nm
Compression Test2 specs
- Air Box Clips4 lb-ft5 Nm
- Connector Bolts5 lb-ft7 Nm
Cooling System Pressure Test1 spec
- Connector Bolts5 lb-ft7 Nm
Diagnostic Scan1 spec
- Connector Bolts5 lb-ft7 Nm
Differential Service3 specs
- Connector Bolts5 lb-ft7 Nm
- Drain PlugNew washer30 lb-ft41 Nm
- Fill Plug30 lb-ft41 Nm
Drivability Diagnosis2 specs
- Air Box Clips4 lb-ft5 Nm
- Connector Bolts5 lb-ft7 Nm
Electrical Diagnosis1 spec
- Connector Bolts5 lb-ft7 Nm
Fluid Leak Diagnosis1 spec
- Connector Bolts5 lb-ft7 Nm
Leak-Down Test2 specs
- Air Box Clips4 lb-ft5 Nm
- Connector Bolts5 lb-ft7 Nm
Noise Diagnosis2 specs
- Connector Bolts5 lb-ft7 Nm
- Wheel Lug NutsTorque in star pattern80 lb-ft108 Nm
Tire Balance2 specs
- Connector Bolts5 lb-ft7 Nm
- Wheel Lug NutsTorque in star pattern80 lb-ft108 Nm
Tire Mount and Balance2 specs
- Connector Bolts5 lb-ft7 Nm
- Wheel Lug NutsTorque in star pattern80 lb-ft108 Nm
Tire Rotation2 specs
- Lug Nuts - Alloy WheelsTorque in star pattern, recheck after 50 miles80 lb-ft108 Nm
- Lug Nuts - Steel WheelsTorque in star pattern80 lb-ft108 Nm
TPMS Relearn1 spec
- Connector Bolts5 lb-ft7 Nm
TPMS Sensor2 specs
- Connector Bolts5 lb-ft7 Nm
- Wheel Lug NutsTorque in star pattern80 lb-ft108 Nm
Transmission Service1 spec
- Connector Bolts5 lb-ft7 Nm
Tune-Up - Major3 specs
- Air Box Clips4 lb-ft5 Nm
- Connector Bolts5 lb-ft7 Nm
- Oil Drain PlugUse new crush washer26 lb-ft35 Nm
Tune-Up - Minor3 specs
- Air Box Clips4 lb-ft5 Nm
- Connector Bolts5 lb-ft7 Nm
- Oil Drain PlugUse new crush washer26 lb-ft35 Nm
Wheel Alignment9 specs
- Air Box Clips4 lb-ft5 Nm
- Cam BoltsAfter adjustment95 lb-ft129 Nm
- Camber BoltsIf adjustable55 lb-ft75 Nm
- Connector Bolts5 lb-ft7 Nm
- Oil Drain PlugUse new crush washer26 lb-ft35 Nm
- Subframe BoltsIf adjusted85 lb-ft115 Nm
- Tie Rod Jam Nuts41 lb-ft55 Nm
- Tie Rod Lock NutAfter adjustment50 lb-ft68 Nm
- Wheel Lug NutsTorque in star pattern80 lb-ft108 Nm

Brakes

ABS Module5 specs
- ABS Module Bolts7 lb-ft10 Nm
- Bleeder Screw10 lb-ft14 Nm
- Brake Line FittingsUse flare nut wrench11 lb-ft15 Nm
- Caliper Mounting BoltsUse thread locker65 lb-ft88 Nm
- Wheel Lug Nuts80 lb-ft108 Nm
ABS Pump3 specs
- Bleeder ScrewDo not overtighten7 lb-ft10 Nm
- Caliper Mounting Bolts65 lb-ft88 Nm
- Wheel Lug NutsTorque in star pattern80 lb-ft108 Nm
ABS Tone Ring4 specs
- Caliper Bracket Bolts - FrontThreadlocker recommended88 lb-ft120 Nm
- Caliper Mounting Bolts65 lb-ft88 Nm
- Caliper Slide Pin BoltsApply silicone brake grease26 lb-ft35 Nm
- Wheel Lug NutsTorque in star pattern80 lb-ft108 Nm
ABS Wheel Speed Sensor - Front5 specs
- ABS Sensor BoltDo not overtighten7 lb-ft10 Nm
- Bleeder Screw10 lb-ft14 Nm
- Caliper Mounting Bolts65 lb-ft88 Nm
- Wheel Bearing Hub Bolts81 lb-ft110 Nm
- Wheel Lug NutsTorque in star pattern80 lb-ft108 Nm
ABS Wheel Speed Sensor - Rear4 specs
- ABS Sensor BoltDo not overtighten7 lb-ft10 Nm
- Bleeder Screw10 lb-ft14 Nm
- Caliper Mounting BoltsUse thread locker65 lb-ft88 Nm
- Wheel Lug Nuts80 lb-ft108 Nm
Brake Bleed - All Four3 specs
- Bleeder ScrewDo not overtighten. Verify sequence with the service manual7 lb-ft10 Nm
- Caliper Mounting BoltsUse thread locker65 lb-ft88 Nm
- Wheel Lug NutsTorque in star pattern. Verify sequence with the service manual80 lb-ft108 Nm
Brake Booster6 specs
- Bleeder Screw10 lb-ft14 Nm
- Brake Booster NutsVerify sequence with the service manual18 lb-ft25 Nm
- Brake Pedal Pushrod LockVerify sequence with the service manual11 lb-ft15 Nm
- Caliper Mounting Bolts65 lb-ft88 Nm
- Master Cylinder NutsVerify sequence with the service manual18 lb-ft25 Nm
- Wheel Lug NutsTorque in star pattern80 lb-ft108 Nm
Brake Booster Check Valve1 spec
- Caliper Mounting BoltsUse thread locker65 lb-ft88 Nm
Brake Caliper - Front3 specs
- Bleeder ScrewDo not overtighten7 lb-ft10 Nm
- Brake Line Banjo BoltUse new copper washers18 lb-ft25 Nm
- Caliper Bracket BoltsThreadlocker recommended88 lb-ft120 Nm
Brake Caliper - Rear3 specs
- Bleeder ScrewDo not overtighten7 lb-ft10 Nm
- Brake Line Banjo BoltUse new copper washers18 lb-ft25 Nm
- Caliper Bracket BoltsThreadlocker recommended74 lb-ft100 Nm
Brake Caliper Bracket6 specs
- Bleeder ScrewDo not overtighten. Verify sequence with the service manual7 lb-ft10 Nm
- Brake Hose Banjo BoltNew copper washers30 lb-ft41 Nm
- Caliper Bracket Bolts - FrontThreadlocker recommended. Verify sequence with the service manual88 lb-ft120 Nm
- Caliper Mounting Bolts65 lb-ft88 Nm
- Caliper Slide Pin BoltsApply silicone brake grease. Verify sequence with the service manual26 lb-ft35 Nm
- Wheel Lug NutsTorque in star pattern. Verify sequence with the service manual80 lb-ft108 Nm
Brake Caliper Rebuild - Front5 specs
- Bleeder ScrewDo not overtighten7 lb-ft10 Nm
- Caliper Bracket Bolts - FrontThreadlocker recommended88 lb-ft120 Nm
- Caliper Mounting BoltsUse thread locker65 lb-ft88 Nm
- Caliper Slide Pin BoltsApply silicone brake grease26 lb-ft35 Nm
- Wheel Lug NutsTorque in star pattern80 lb-ft108 Nm
Brake Caliper Rebuild - Rear4 specs
- Bleeder ScrewDo not overtighten7 lb-ft10 Nm
- Caliper Mounting Bolts65 lb-ft88 Nm
- Caliper Slide Pin BoltsApply silicone brake grease26 lb-ft35 Nm
- Wheel Lug NutsTorque in star pattern80 lb-ft108 Nm
Brake Caliper Slide Pins4 specs
- Caliper Bracket Bolts - FrontThreadlocker recommended88 lb-ft120 Nm
- Caliper Mounting Bolts65 lb-ft88 Nm
- Caliper Slide Pin BoltsApply silicone brake grease26 lb-ft35 Nm
- Wheel Lug NutsTorque in star pattern80 lb-ft108 Nm
Brake Drum - Rear2 specs
- Caliper Mounting Bolts65 lb-ft88 Nm
- Wheel Lug NutsTorque in star pattern. Verify sequence with the service manual80 lb-ft108 Nm
Brake Fluid Flush7 specs
- Air Box ClipsVerify sequence with the service manual4 lb-ft5 Nm
- Bleeder ScrewDo not overtighten. Verify sequence with the service manual7 lb-ft10 Nm
- Caliper Mounting Bolts65 lb-ft88 Nm
- Connector Bolts5 lb-ft7 Nm
- Master Cylinder CapHand tight3 lb-ft4 Nm
- Oil Drain PlugUse new crush washer. Verify sequence with the service manual26 lb-ft35 Nm
- Wheel Lug NutsTorque in star pattern. Verify sequence with the service manual80 lb-ft108 Nm
Brake Hose - Front5 specs
- Bleeder Screw10 lb-ft14 Nm
- Brake Hose Banjo BoltUse new copper washers. Verify sequence with the service manual18 lb-ft25 Nm
- Brake Hose BracketVerify sequence with the service manual7 lb-ft10 Nm
- Caliper Mounting Bolts65 lb-ft88 Nm
- Wheel Lug NutsTorque in star pattern80 lb-ft108 Nm
Brake Hose - Rear5 specs
- Bleeder Screw10 lb-ft14 Nm
- Brake Hose Banjo BoltUse new copper washers. Verify sequence with the service manual18 lb-ft25 Nm
- Brake Hose BracketVerify sequence with the service manual7 lb-ft10 Nm
- Caliper Mounting BoltsUse thread locker65 lb-ft88 Nm
- Wheel Lug NutsTorque in star pattern80 lb-ft108 Nm
Brake Light Switch1 spec
- Caliper Mounting Bolts65 lb-ft88 Nm
Brake Line - Single3 specs
- Bleeder ScrewDo not overtighten. Verify sequence with the service manual7 lb-ft10 Nm
- Caliper Mounting Bolts65 lb-ft88 Nm
- Wheel Lug NutsTorque in star pattern. Verify sequence with the service manual80 lb-ft108 Nm
Brake Lines - Complete Set3 specs
- Bleeder ScrewDo not overtighten. Verify sequence with the service manual7 lb-ft10 Nm
- Caliper Mounting Bolts65 lb-ft88 Nm
- Wheel Lug NutsTorque in star pattern. Verify sequence with the service manual80 lb-ft108 Nm
Brake Master Cylinder2 specs
- Brake Line FittingsUse flare nut wrench11 lb-ft15 Nm
- Master Cylinder Nuts18 lb-ft25 Nm
Brake Master Cylinder Rebuild3 specs
- Brake Line FittingsUse flare nut wrench11 lb-ft15 Nm
- Master Cylinder Mounting Nuts18 lb-ft25 Nm
- Reservoir Mounting Bolts6 lb-ft8 Nm
Brake Pads - Front3 specs
- Caliper Bracket BoltsThreadlocker recommended88 lb-ft120 Nm
- Caliper Slide Pin BoltsApply silicone brake grease26 lb-ft35 Nm
- Wheel Lug NutsTorque in star pattern80 lb-ft108 Nm
Brake Pads - Rear3 specs
- Caliper Bracket BoltsThreadlocker recommended74 lb-ft100 Nm
- Caliper Slide Pin BoltsApply silicone brake grease22 lb-ft30 Nm
- Wheel Lug NutsTorque in star pattern80 lb-ft108 Nm
Brake Pads and Rotors - Front7 specs
- Bleeder ScrewDo not overtighten. Verify sequence with the service manual7 lb-ft10 Nm
- Caliper Bracket BoltsUse thread locker75 lb-ft102 Nm
- Caliper Bracket Bolts - FrontThreadlocker recommended. Verify sequence with the service manual88 lb-ft120 Nm
- Caliper Mounting Bolts65 lb-ft88 Nm
- Caliper Slide BoltsLubricate pins25 lb-ft34 Nm
- Caliper Slide Pin BoltsApply silicone brake grease. Verify sequence with the service manual26 lb-ft35 Nm
- Wheel Lug NutsTorque in star pattern. Verify sequence with the service manual80 lb-ft108 Nm
Brake Pads and Rotors - Rear6 specs
- Bleeder ScrewDo not overtighten. Verify sequence with the service manual7 lb-ft10 Nm
- Caliper Bracket BoltsUse thread locker75 lb-ft102 Nm
- Caliper Mounting Bolts65 lb-ft88 Nm
- Caliper Slide BoltsLubricate pins25 lb-ft34 Nm
- Caliper Slide Pin BoltsApply silicone brake grease. Verify sequence with the service manual26 lb-ft35 Nm
- Wheel Lug NutsTorque in star pattern. Verify sequence with the service manual80 lb-ft108 Nm
Brake Proportioning Valve5 specs
- Bleeder Screw10 lb-ft14 Nm
- Brake Line FittingsUse flare nut wrench. Verify sequence with the service manual11 lb-ft15 Nm
- Caliper Mounting BoltsUse thread locker65 lb-ft88 Nm
- Proportioning Valve BoltsVerify sequence with the service manual11 lb-ft15 Nm
- Wheel Lug NutsTorque in star pattern80 lb-ft108 Nm
Brake Rotor - Front Single7 specs
- Brake Rotor Set Screw5 lb-ft7 Nm
- Caliper Bracket Bolts75 lb-ft102 Nm
- Caliper Bracket Bolts - FrontThreadlocker recommended. Verify sequence with the service manual88 lb-ft120 Nm
- Caliper Mounting Bolts65 lb-ft88 Nm
- Caliper Slide Pin BoltsApply silicone brake grease. Verify sequence with the service manual26 lb-ft35 Nm
- Hub NutIf removed180 lb-ft244 Nm
- Wheel Lug NutsTorque in star pattern. Verify sequence with the service manual80 lb-ft108 Nm
Brake Rotor - Rear Single6 specs
- Brake Rotor Set Screw5 lb-ft7 Nm
- Caliper Bracket Bolts75 lb-ft102 Nm
- Caliper Mounting BoltsUse thread locker65 lb-ft88 Nm
- Caliper Slide Pin BoltsApply silicone brake grease. Verify sequence with the service manual26 lb-ft35 Nm
- Hub NutIf removed180 lb-ft244 Nm
- Wheel Lug NutsTorque in star pattern. Verify sequence with the service manual80 lb-ft108 Nm
Brake Rotors - Front Pair7 specs
- Brake Rotor Set Screw5 lb-ft7 Nm
- Caliper Bracket Bolts75 lb-ft102 Nm
- Caliper Bracket Bolts - FrontThreadlocker recommended. Verify sequence with the service manual88 lb-ft120 Nm
- Caliper Mounting Bolts65 lb-ft88 Nm
- Caliper Slide Pin BoltsApply silicone brake grease. Verify sequence with the service manual26 lb-ft35 Nm
- Hub NutIf removed180 lb-ft244 Nm
- Wheel Lug NutsTorque in star pattern. Verify sequence with the service manual80 lb-ft108 Nm
Brake Rotors - Rear Pair6 specs
- Brake Rotor Set Screw5 lb-ft7 Nm
- Caliper Bracket Bolts75 lb-ft102 Nm
- Caliper Mounting Bolts65 lb-ft88 Nm
- Caliper Slide Pin BoltsApply silicone brake grease. Verify sequence with the service manual26 lb-ft35 Nm
- Hub NutIf removed180 lb-ft244 Nm
- Wheel Lug NutsTorque in star pattern. Verify sequence with the service manual80 lb-ft108 Nm
Drum Brake Hardware Kit2 specs
- Caliper Mounting BoltsUse thread locker65 lb-ft88 Nm
- Wheel Lug NutsTorque in star pattern. Verify sequence with the service manual80 lb-ft108 Nm
Drum Brake Shoes - Rear2 specs
- Caliper Mounting BoltsUse thread locker65 lb-ft88 Nm
- Wheel Lug NutsTorque in star pattern. Verify sequence with the service manual80 lb-ft108 Nm
Electronic Parking Brake Motor3 specs
- Caliper Mounting BoltsUse thread locker65 lb-ft88 Nm
- Caliper Slide Pin BoltsApply silicone brake grease. Verify sequence with the service manual26 lb-ft35 Nm
- Wheel Lug NutsTorque in star pattern. Verify sequence with the service manual80 lb-ft108 Nm
Front Brake Pad Replacement3 specs
- Caliper Bracket BoltsThreadlocker recommended88 lb-ft120 Nm
- Caliper Slide Pin BoltsApply silicone brake grease26 lb-ft35 Nm
- Wheel Lug NutsTorque in star pattern80 lb-ft108 Nm
Parking Brake Actuator3 specs
- Caliper Mounting Bolts65 lb-ft88 Nm
- Caliper Slide Pin BoltsApply silicone brake grease. Verify sequence with the service manual26 lb-ft35 Nm
- Wheel Lug NutsTorque in star pattern. Verify sequence with the service manual80 lb-ft108 Nm
Parking Brake Cable5 specs
- Bleeder Screw10 lb-ft14 Nm
- Cable Bracket BoltsVerify sequence with the service manual9 lb-ft12 Nm
- Caliper Mounting BoltsUse thread locker65 lb-ft88 Nm
- Equalizer NutAdjust for proper tension. Verify sequence with the service manual11 lb-ft15 Nm
- Wheel Lug Nuts80 lb-ft108 Nm
Parking Brake Shoes5 specs
- Adjuster LockVerify sequence with the service manual4 lb-ft5 Nm
- Bleeder Screw10 lb-ft14 Nm
- Caliper Mounting BoltsUse thread locker65 lb-ft88 Nm
- Hold-Down SpringsVerify sequence with the service manual6 lb-ft8 Nm
- Wheel Lug NutsTorque in star pattern. Verify sequence with the service manual80 lb-ft108 Nm
Rear Brake Shoe Replacement3 specs
- Backing Plate Bolts44 lb-ft60 Nm
- Wheel Cylinder Bolts9 lb-ft12 Nm
- Wheel Lug NutsTorque in star pattern80 lb-ft108 Nm
Wheel Cylinder3 specs
- Bleeder ScrewDo not overtighten7 lb-ft10 Nm
- Caliper Mounting Bolts65 lb-ft88 Nm
- Wheel Lug NutsTorque in star pattern80 lb-ft108 Nm

Engine

Camshaft Position Sensor5 specs
- Camshaft Position Sensor7 lb-ft10 Nm
- Electrical Connector Bolts5 lb-ft7 Nm
- Gasket Surface BoltsClean mating surfaces15 lb-ft20 Nm
- Sensor Mounting Bolts8 lb-ft11 Nm
- Valve Cover BoltsTighten in sequence7 lb-ft10 Nm
Camshaft R&R20 specs
- Cam Phaser BoltApply threadlocker, hold cam stationary48 lb-ft65 Nm
- Camshaft Bearing Cap BoltsTighten in sequence, 3 passes10 lb-ft14 Nm
- Camshaft Cap BoltsTighten in sequence from center outward, multiple passes10 lb-ft14 Nm
- Camshaft Position Sensor7 lb-ft10 Nm
- Camshaft Sprocket BoltsHold cam with wrench on hex59 lb-ft80 Nm
- Crankshaft Position Sensor7 lb-ft10 Nm
- Crankshaft Pulley BoltOften TTY, may need impact133 lb-ft180 Nm
- Electrical Connector Bolts5 lb-ft7 Nm
- Gasket Surface BoltsClean mating surfaces15 lb-ft20 Nm
- Oil Drain PlugUse new crush washer26 lb-ft35 Nm
- Rocker Arm BoltsTighten with cam lobe pointing away22 lb-ft30 Nm
- Rocker Arm Shaft BoltsTighten evenly in sequence18 lb-ft25 Nm
- Sensor Mounting Bolts8 lb-ft11 Nm
- Timing Chain Guide BoltsReplace if worn9 lb-ft12 Nm
- Timing Chain Idler Sprocket18 lb-ft25 Nm
- Timing Chain Tensioner BoltInstall with pin/clip to compress18 lb-ft25 Nm
- Timing Cover Bolts - 10mmTighten in sequence33 lb-ft45 Nm
- Timing Cover Bolts - 8mmTighten in sequence18 lb-ft25 Nm
- Valve Cover BoltsTighten in sequence7 lb-ft10 Nm
- VVT Solenoid Bolt7 lb-ft10 Nm
Connecting Rod Bearings6 specs
- Connecting Rod BoltsTTY - critical torque plus angle33 lb-ft45 Nm
- Electrical Connector Bolts5 lb-ft7 Nm
- Gasket Surface BoltsClean mating surfaces15 lb-ft20 Nm
- Oil Drain PlugUse new crush washer26 lb-ft35 Nm
- Oil Pan BoltTighten in sequence9 lb-ft12 Nm
- Sensor Mounting Bolts8 lb-ft11 Nm
Crankshaft Position Sensor4 specs
- Crankshaft Position Sensor7 lb-ft10 Nm
- Electrical Connector Bolts5 lb-ft7 Nm
- Gasket Surface BoltsClean mating surfaces15 lb-ft20 Nm
- Sensor Mounting Bolts8 lb-ft11 Nm
Crankshaft R&R20 specs
- Connecting Rod BoltsTTY - critical torque plus angle33 lb-ft45 Nm
- Crankshaft Pulley BoltOften TTY - check spec, may require impact133 lb-ft180 Nm
- Cylinder Head BoltsTTY - tighten in sequence plus angle48 lb-ft65 Nm
- Electrical Connector Bolts5 lb-ft7 Nm
- Flexplate BoltsAutomatic transmissions63 lb-ft85 Nm
- Flywheel BoltsOften TTY, tighten in star pattern70 lb-ft95 Nm
- Front Main Seal Housing9 lb-ft12 Nm
- Gasket Surface BoltsClean mating surfaces15 lb-ft20 Nm
- Main Bearing Cap BoltsTTY - tighten in sequence plus angle55 lb-ft75 Nm
- Oil Drain PlugUse new crush washer26 lb-ft35 Nm
- Oil Pan BoltTighten in sequence9 lb-ft12 Nm
- Oil Pump Bolts9 lb-ft12 Nm
- Oil Pump Pickup Tube9 lb-ft12 Nm
- Rear Main Seal Housing9 lb-ft12 Nm
- Sensor Mounting Bolts8 lb-ft11 Nm
- Timing Chain Guide BoltsReplace if worn9 lb-ft12 Nm
- Timing Chain Tensioner BoltInstall with pin/clip to compress18 lb-ft25 Nm
- Timing Cover Bolts - 10mmTighten in sequence33 lb-ft45 Nm
- Timing Cover Bolts - 8mmTighten in sequence18 lb-ft25 Nm
- Transmission-to-Engine Bolts41 lb-ft55 Nm
Cylinder Head R&R17 specs
- Camshaft Bearing Cap BoltsTighten in sequence, 3 passes10 lb-ft14 Nm
- Camshaft Cap BoltsTighten in sequence from center outward, multiple passes10 lb-ft14 Nm
- Camshaft Sprocket BoltsHold cam with wrench on hex59 lb-ft80 Nm
- Cylinder Head BoltsTTY - tighten in sequence plus angle48 lb-ft65 Nm
- Electrical Connector Bolts5 lb-ft7 Nm
- Exhaust Manifold NutsApply anti-seize, work hot-to-cold22 lb-ft30 Nm
- Gasket Surface BoltsClean mating surfaces15 lb-ft20 Nm
- Intake Manifold Bolt18 lb-ft25 Nm
- Oil Drain PlugUse new crush washer26 lb-ft35 Nm
- Rocker Arm BoltsTighten with cam lobe pointing away22 lb-ft30 Nm
- Rocker Arm Shaft BoltsTighten evenly in sequence18 lb-ft25 Nm
- Sensor Mounting Bolts8 lb-ft11 Nm
- Thermostat Housing Bolt11 lb-ft15 Nm
- Timing Chain Guide BoltsReplace if worn9 lb-ft12 Nm
- Timing Chain Tensioner BoltInstall with pin/clip to compress18 lb-ft25 Nm
- Timing Cover Bolts - 8mmTighten in sequence18 lb-ft25 Nm
- Valve Cover BoltsTighten in sequence7 lb-ft10 Nm
Cylinder Head Resurface7 specs
- Cylinder Head BoltsTTY - tighten in sequence plus angle48 lb-ft65 Nm
- Electrical Connector Bolts5 lb-ft7 Nm
- Exhaust Manifold NutsApply anti-seize, work hot-to-cold22 lb-ft30 Nm
- Gasket Surface BoltsClean mating surfaces15 lb-ft20 Nm
- Intake Manifold Bolt18 lb-ft25 Nm
- Sensor Mounting Bolts8 lb-ft11 Nm
- Valve Cover BoltsTighten in sequence7 lb-ft10 Nm
Engine Mount - Front3 specs
- Engine Mount Through-Bolt63 lb-ft85 Nm
- Engine Mount-to-Block Bolts48 lb-ft65 Nm
- Engine Mount-to-Frame Bolts55 lb-ft75 Nm
Engine Mount - Rear6 specs
- Electrical Connector Bolts5 lb-ft7 Nm
- Engine Mount Through-Bolt65 lb-ft88 Nm
- Engine Mount-to-Block Bolts48 lb-ft65 Nm
- Engine Mount-to-Frame Bolts45 lb-ft61 Nm
- Gasket Surface BoltsClean mating surfaces15 lb-ft20 Nm
- Sensor Mounting Bolts8 lb-ft11 Nm
Engine Mounts - All7 specs
- Electrical Connector Bolts5 lb-ft7 Nm
- Engine Mount Through-Bolt63 lb-ft85 Nm
- Engine Mount-to-Block Bolts48 lb-ft65 Nm
- Engine Mount-to-Frame Bolts45 lb-ft61 Nm
- Gasket Surface BoltsClean mating surfaces15 lb-ft20 Nm
- Sensor Mounting Bolts8 lb-ft11 Nm
- Transmission Mount Bolts48 lb-ft65 Nm
Engine R&R13 specs
- AC Compressor Bolts18 lb-ft25 Nm
- Alternator Mounting Bolts37 lb-ft50 Nm
- Electrical Connector Bolts5 lb-ft7 Nm
- Engine Mount-to-Block Bolts48 lb-ft65 Nm
- Engine Mount-to-Frame Bolts55 lb-ft75 Nm
- Exhaust Manifold NutsApply anti-seize, work hot-to-cold22 lb-ft30 Nm
- Flywheel BoltsOften TTY, tighten in star pattern70 lb-ft95 Nm
- Gasket Surface BoltsClean mating surfaces15 lb-ft20 Nm
- Oil Drain PlugUse new crush washer26 lb-ft35 Nm
- Power Steering Pump Bolts18 lb-ft25 Nm
- Sensor Mounting Bolts8 lb-ft11 Nm
- Starter Mounting Bolt37 lb-ft50 Nm
- Transmission-to-Engine Bolts41 lb-ft55 Nm
Engine Rebuild21 specs
- Balance Shaft Bolts18 lb-ft25 Nm
- Camshaft Bearing Cap BoltsTighten in sequence, 3 passes10 lb-ft14 Nm
- Camshaft Cap BoltsTighten in sequence from center outward, multiple passes10 lb-ft14 Nm
- Connecting Rod BoltsTTY - critical torque plus angle33 lb-ft45 Nm
- Crankshaft Pulley BoltOften TTY - check spec, may require impact133 lb-ft180 Nm
- Cylinder Head BoltsTTY - tighten in sequence plus angle48 lb-ft65 Nm
- Electrical Connector Bolts5 lb-ft7 Nm
- Exhaust Manifold NutsApply anti-seize, work hot-to-cold22 lb-ft30 Nm
- Flywheel BoltsOften TTY, tighten in star pattern70 lb-ft95 Nm
- Gasket Surface BoltsClean mating surfaces15 lb-ft20 Nm
- Intake Manifold Bolt18 lb-ft25 Nm
- Main Bearing Cap BoltsTTY - tighten in sequence plus angle55 lb-ft75 Nm
- Oil Drain PlugUse new crush washer26 lb-ft35 Nm
- Oil Pan BoltTighten in sequence9 lb-ft12 Nm
- Oil Pump Bolts9 lb-ft12 Nm
- Oil Pump Pickup Tube9 lb-ft12 Nm
- Sensor Mounting Bolts8 lb-ft11 Nm
- Timing Chain Guide BoltsReplace if worn9 lb-ft12 Nm
- Timing Chain Tensioner BoltInstall with pin/clip to compress18 lb-ft25 Nm
- Timing Cover Bolts - 8mmTighten in sequence18 lb-ft25 Nm
- Valve Cover BoltsTighten in sequence7 lb-ft10 Nm
Exhaust Manifold8 specs
- Electrical Connector Bolts5 lb-ft7 Nm
- Exhaust Flange BoltApply anti-seize. Verify sequence with the service manual33 lb-ft45 Nm
- Exhaust Manifold NutsApply anti-seize, work hot-to-cold. Verify sequence with the service manual22 lb-ft30 Nm
- Gasket Surface BoltsClean mating surfaces15 lb-ft20 Nm
- Hanger Bolts15 lb-ft20 Nm
- Heat Shield BoltsVerify sequence with the service manual7 lb-ft10 Nm
- O2 SensorAnti-seize threads35 lb-ft47 Nm
- Sensor Mounting Bolts8 lb-ft11 Nm
Exhaust Manifold Gasket3 specs
- Exhaust Manifold NutsApply anti-seize, work hot-to-cold22 lb-ft30 Nm
- Exhaust Manifold StudsIf replacing studs11 lb-ft15 Nm
- Heat Shield Bolts7 lb-ft10 Nm
Fan Belt Replacement3 specs
- Idler Pulley Bolt30 lb-ft40 Nm
- Tensioner Bolt18 lb-ft25 Nm
- Tensioner Pulley Bolt33 lb-ft45 Nm
Flexplate6 specs
- Electrical Connector Bolts5 lb-ft7 Nm
- Flexplate BoltsAutomatic transmissions. Verify sequence with the service manual63 lb-ft85 Nm
- Gasket Surface BoltsClean mating surfaces15 lb-ft20 Nm
- Sensor Mounting Bolts8 lb-ft11 Nm
- Torque Converter BoltsVerify sequence with the service manual37 lb-ft50 Nm
- Transmission-to-Engine BoltsVerify sequence with the service manual41 lb-ft55 Nm
Flywheel6 specs
- Drain PlugUse new washer25 lb-ft34 Nm
- Fill Plug25 lb-ft34 Nm
- Flexplate BoltsAutomatic transmissions63 lb-ft85 Nm
- Flywheel BoltsOften TTY - check specs, tighten in star pattern70 lb-ft95 Nm
- Transmission Drain PlugUse new crush washer if equipped22 lb-ft30 Nm
- Transmission Pan BoltsTighten in criss-cross pattern9 lb-ft12 Nm
Freeze Plug - Single4 specs
- Electrical Connector Bolts5 lb-ft7 Nm
- Freeze PlugUse sealant on edges7 lb-ft10 Nm
- Gasket Surface BoltsClean mating surfaces15 lb-ft20 Nm
- Sensor Mounting Bolts8 lb-ft11 Nm
Freeze Plugs - All4 specs
- Electrical Connector Bolts5 lb-ft7 Nm
- Freeze PlugUse sealant on edges7 lb-ft10 Nm
- Gasket Surface BoltsClean mating surfaces15 lb-ft20 Nm
- Sensor Mounting Bolts8 lb-ft11 Nm
Front Main Seal8 specs
- Crankshaft Pulley BoltOften TTY, may need impact133 lb-ft180 Nm
- Electrical Connector Bolts5 lb-ft7 Nm
- Gasket Surface BoltsClean mating surfaces15 lb-ft20 Nm
- Oil Drain PlugUse new crush washer26 lb-ft35 Nm
- Oil Pan BoltFront section only9 lb-ft12 Nm
- Sensor Mounting Bolts8 lb-ft11 Nm
- Timing Cover Bolts - 10mmTighten in sequence33 lb-ft45 Nm
- Timing Cover Bolts - 8mmTighten in sequence18 lb-ft25 Nm
Full Engine Tune-Up5 specs
- Ignition Coil Bolt6 lb-ft8 Nm
- Spark Plugs - Aluminum HeadApply anti-seize to threads15 lb-ft20 Nm
- Spark Plugs - Cast Iron HeadApply anti-seize to threads22 lb-ft30 Nm
- Throttle Body Bolts7 lb-ft10 Nm
- Valve Cover BoltsTighten in sequence7 lb-ft10 Nm
Harmonic Balancer4 specs
- Crankshaft Pulley BoltOften TTY, may need impact. Verify sequence with the service manual133 lb-ft180 Nm
- Electrical Connector Bolts5 lb-ft7 Nm
- Gasket Surface BoltsClean mating surfaces15 lb-ft20 Nm
- Sensor Mounting Bolts8 lb-ft11 Nm
Head Gasket - Single6 specs
- Exhaust Manifold NutsApply anti-seize18 lb-ft25 Nm
- Intake Manifold BoltTighten in sequence18 lb-ft25 Nm
- Cylinder Head Bolts - Step 1Always use new TTY bolts30 lb-ft40 Nm
- Cylinder Head Bolts - Step 2Tighten in sequence59 lb-ft80 Nm
- Cylinder Head Bolts - Step 3Plus 90 degreesTurn 90°
- Cylinder Head Bolts - Step 4Plus 90 degreesTurn 90°
Head Gaskets - Both15 specs
- Camshaft Cap BoltsTighten in sequence from center outward, multiple passes10 lb-ft14 Nm
- Camshaft Sprocket BoltsHold cam with wrench on hex59 lb-ft80 Nm
- Crankshaft Pulley BoltOften TTY - check spec, may require impact133 lb-ft180 Nm
- Cylinder Head BoltsMulti-step + angle65 lb-ft88 Nm
- Electrical Connector Bolts5 lb-ft7 Nm
- Exhaust Manifold Nuts25 lb-ft34 Nm
- Gasket Surface BoltsClean mating surfaces15 lb-ft20 Nm
- Intake Manifold Bolt18 lb-ft24 Nm
- Oil Drain PlugUse new crush washer26 lb-ft35 Nm
- Rocker Arm BoltsTighten with cam lobe pointing away22 lb-ft30 Nm
- Sensor Mounting Bolts7 lb-ft10 Nm
- Timing Chain Tensioner BoltInstall with pin/clip to compress18 lb-ft25 Nm
- Timing Cover Bolts - 8mmTighten in sequence18 lb-ft25 Nm
- Valve Cover BoltsTighten in sequence7 lb-ft10 Nm
- VVT Solenoid Bolt7 lb-ft10 Nm
Idle Air Control Valve4 specs
- Electrical Connector Bolts5 lb-ft7 Nm
- Gasket Surface BoltsClean mating surfaces15 lb-ft20 Nm
- IAC Valve Screws2 lb-ft3 Nm
- Sensor Mounting Bolts8 lb-ft11 Nm
Idler Pulley4 specs
- Electrical Connector Bolts5 lb-ft7 Nm
- Gasket Surface BoltsClean mating surfaces15 lb-ft20 Nm
- Idler Pulley Bolt33 lb-ft45 Nm
- Sensor Mounting Bolts8 lb-ft11 Nm
Intake Manifold7 specs
- Electrical Connector Bolts5 lb-ft7 Nm
- Fuel Rail BoltsVerify sequence with the service manual9 lb-ft12 Nm
- Gasket Surface BoltsClean mating surfaces15 lb-ft20 Nm
- Intake Manifold BoltTighten in sequence from center out. Verify sequence with the service manual18 lb-ft25 Nm
- PCV ValveVerify sequence with the service manual6 lb-ft8 Nm
- Sensor Mounting Bolts8 lb-ft11 Nm
- Throttle Body BoltsVerify sequence with the service manual7 lb-ft10 Nm
Intake Manifold Gasket3 specs
- Fuel Rail Bolts9 lb-ft12 Nm
- Intake Manifold BoltTighten in sequence from center out18 lb-ft25 Nm
- Throttle Body Bolts7 lb-ft10 Nm
Knock Sensor4 specs
- Electrical Connector Bolts5 lb-ft7 Nm
- Gasket Surface BoltsClean mating surfaces15 lb-ft20 Nm
- Knock SensorTorque critical for function15 lb-ft20 Nm
- Sensor Mounting Bolts8 lb-ft11 Nm
Lifter - Single7 specs
- Electrical Connector Bolts5 lb-ft7 Nm
- Gasket Surface BoltsClean mating surfaces15 lb-ft20 Nm
- Intake Manifold Bolt18 lb-ft25 Nm
- Rocker Arm BoltsTighten with cam lobe pointing away22 lb-ft30 Nm
- Rocker Arm Shaft BoltsTighten evenly in sequence18 lb-ft25 Nm
- Sensor Mounting Bolts8 lb-ft11 Nm
- Valve Cover BoltsTighten in sequence7 lb-ft10 Nm
Lifters/Tappets - All10 specs
- Camshaft Bearing Cap BoltsTighten in sequence, 3 passes10 lb-ft14 Nm
- Camshaft Cap BoltsTighten in sequence from center outward, multiple passes10 lb-ft14 Nm
- Camshaft Position Sensor7 lb-ft10 Nm
- Electrical Connector Bolts5 lb-ft7 Nm
- Gasket Surface BoltsClean mating surfaces15 lb-ft20 Nm
- Intake Manifold Bolt18 lb-ft25 Nm
- Rocker Arm BoltsTighten with cam lobe pointing away22 lb-ft30 Nm
- Rocker Arm Shaft BoltsTighten evenly in sequence18 lb-ft25 Nm
- Sensor Mounting Bolts8 lb-ft11 Nm
- Valve Cover BoltsTighten in sequence7 lb-ft10 Nm
Long Block Replacement16 specs
- Camshaft Cap BoltsTighten in sequence from center outward, multiple passes10 lb-ft14 Nm
- Connecting Rod BoltsTTY - critical torque plus angle33 lb-ft45 Nm
- Cylinder Head BoltsTTY - tighten in sequence plus angle48 lb-ft65 Nm
- Electrical Connector Bolts5 lb-ft7 Nm
- Exhaust Manifold NutsApply anti-seize, work hot-to-cold22 lb-ft30 Nm
- Flywheel BoltsOften TTY, tighten in star pattern70 lb-ft95 Nm
- Gasket Surface BoltsClean mating surfaces15 lb-ft20 Nm
- Intake Manifold Bolt18 lb-ft25 Nm
- Main Bearing Cap BoltsTTY - tighten in sequence plus angle55 lb-ft75 Nm
- Oil Drain PlugUse new crush washer26 lb-ft35 Nm
- Oil Pan Bolt9 lb-ft12 Nm
- Sensor Mounting Bolts8 lb-ft11 Nm
- Timing Chain Tensioner BoltInstall with pin/clip to compress18 lb-ft25 Nm
- Timing Cover Bolts - 8mmTighten in sequence18 lb-ft25 Nm
- Transmission-to-Engine Bolts41 lb-ft55 Nm
- Valve Cover BoltsTighten in sequence7 lb-ft10 Nm
Main Bearings9 specs
- Electrical Connector Bolts5 lb-ft7 Nm
- Flywheel BoltsOften TTY, tighten in star pattern. Verify sequence with the service manual70 lb-ft95 Nm
- Gasket Surface BoltsClean mating surfaces15 lb-ft20 Nm
- Main Bearing Cap BoltsTTY - tighten in sequence plus angle. Verify sequence with the service manual55 lb-ft75 Nm
- Oil Drain PlugUse new crush washer. Verify sequence with the service manual26 lb-ft35 Nm
- Oil Pan BoltTighten in sequence. Verify sequence with the service manual9 lb-ft12 Nm
- Oil Pump Pickup TubeVerify sequence with the service manual9 lb-ft12 Nm
- Sensor Mounting Bolts8 lb-ft11 Nm
- Transmission-to-Engine BoltsVerify sequence with the service manual41 lb-ft55 Nm
Manifold Absolute Pressure Sensor4 specs
- Electrical Connector Bolts5 lb-ft7 Nm
- Gasket Surface BoltsClean mating surfaces15 lb-ft20 Nm
- MAP Sensor Screws2 lb-ft3 Nm
- Sensor Mounting Bolts8 lb-ft11 Nm
Mass Air Flow Sensor5 specs
- Air Intake Clamps2 lb-ft3 Nm
- Electrical Connector Bolts5 lb-ft7 Nm
- Gasket Surface BoltsClean mating surfaces15 lb-ft20 Nm
- MAF Sensor Screws2 lb-ft3 Nm
- Sensor Mounting Bolts8 lb-ft11 Nm
Oil Change2 specs
- Oil Drain PlugUse new crush washer27 lb-ft37 Nm
- Oil Filter Housing CapFor cartridge-type filters19 lb-ft26 Nm
Oil Level Sensor5 specs
- Electrical Connector Bolts5 lb-ft7 Nm
- Gasket Surface BoltsClean mating surfaces15 lb-ft20 Nm
- Oil Level Sensor11 lb-ft15 Nm
- Oil Pan BoltIf access needed9 lb-ft12 Nm
- Sensor Mounting Bolts8 lb-ft11 Nm
Oil Pan Gasket2 specs
- Oil Drain PlugUse new crush washer26 lb-ft35 Nm
- Oil Pan BoltTighten in sequence from center outward9 lb-ft12 Nm
Oil Pan Replacement6 specs
- Electrical Connector Bolts5 lb-ft7 Nm
- Gasket Surface BoltsClean mating surfaces15 lb-ft20 Nm
- Oil Drain PlugUse new crush washer26 lb-ft35 Nm
- Oil Pan BoltTighten in sequence9 lb-ft12 Nm
- Oil Pump Pickup Tube9 lb-ft12 Nm
- Sensor Mounting Bolts8 lb-ft11 Nm
Oil Pressure Sensor4 specs
- Electrical Connector Bolts5 lb-ft7 Nm
- Gasket Surface BoltsClean mating surfaces15 lb-ft20 Nm
- Oil Pressure SensorUse thread sealant15 lb-ft20 Nm
- Sensor Mounting Bolts8 lb-ft11 Nm
Oil Pump8 specs
- Electrical Connector Bolts5 lb-ft7 Nm
- Gasket Surface BoltsClean mating surfaces15 lb-ft20 Nm
- Oil Drain PlugUse new crush washer26 lb-ft35 Nm
- Oil Pan Bolt9 lb-ft12 Nm
- Oil Pump Bolts9 lb-ft12 Nm
- Oil Pump Pickup Tube9 lb-ft12 Nm
- Sensor Mounting Bolts8 lb-ft11 Nm
- Timing Cover Bolts - 8mmTighten in sequence18 lb-ft25 Nm
PCV Valve4 specs
- Electrical Connector Bolts5 lb-ft7 Nm
- Gasket Surface BoltsClean mating surfaces15 lb-ft20 Nm
- PCV ValveHand tight usually6 lb-ft8 Nm
- Sensor Mounting Bolts8 lb-ft11 Nm
Piston - Single7 specs
- Connecting Rod BoltsTTY - critical torque plus angle33 lb-ft45 Nm
- Cylinder Head BoltsTTY - tighten in sequence plus angle48 lb-ft65 Nm
- Electrical Connector Bolts5 lb-ft7 Nm
- Gasket Surface BoltsClean mating surfaces15 lb-ft20 Nm
- Oil Drain PlugUse new crush washer26 lb-ft35 Nm
- Oil Pan Bolt9 lb-ft12 Nm
- Sensor Mounting Bolts8 lb-ft11 Nm
Piston Rings - All9 specs
- Connecting Rod BoltsTTY - critical torque plus angle33 lb-ft45 Nm
- Cylinder Head BoltsTTY - tighten in sequence plus angle48 lb-ft65 Nm
- Electrical Connector Bolts5 lb-ft7 Nm
- Gasket Surface BoltsClean mating surfaces15 lb-ft20 Nm
- Main Bearing Cap BoltsTTY - tighten in sequence plus angle55 lb-ft75 Nm
- Oil Drain PlugUse new crush washer26 lb-ft35 Nm
- Oil Pan BoltTighten in sequence9 lb-ft12 Nm
- Oil Pump Pickup Tube9 lb-ft12 Nm
- Sensor Mounting Bolts8 lb-ft11 Nm
Pistons - All9 specs
- Connecting Rod BoltsTTY - critical torque plus angle33 lb-ft45 Nm
- Cylinder Head BoltsTTY - tighten in sequence plus angle48 lb-ft65 Nm
- Electrical Connector Bolts5 lb-ft7 Nm
- Gasket Surface BoltsClean mating surfaces15 lb-ft20 Nm
- Main Bearing Cap BoltsTTY - tighten in sequence plus angle55 lb-ft75 Nm
- Oil Drain PlugUse new crush washer26 lb-ft35 Nm
- Oil Pan Bolt9 lb-ft12 Nm
- Oil Pump Pickup Tube9 lb-ft12 Nm
- Sensor Mounting Bolts8 lb-ft11 Nm
Rear Main Seal9 specs
- Electrical Connector Bolts5 lb-ft7 Nm
- Flexplate BoltsAutomatic transmissions63 lb-ft85 Nm
- Flywheel BoltsOften TTY, tighten in star pattern70 lb-ft95 Nm
- Gasket Surface BoltsClean mating surfaces15 lb-ft20 Nm
- Oil Drain PlugUse new crush washer26 lb-ft35 Nm
- Oil Pan BoltRear section9 lb-ft12 Nm
- Rear Main Seal Housing9 lb-ft12 Nm
- Sensor Mounting Bolts8 lb-ft11 Nm
- Transmission-to-Engine Bolts41 lb-ft55 Nm
Rocker Arms - All7 specs
- Electrical Connector Bolts5 lb-ft7 Nm
- Gasket Surface BoltsClean mating surfaces15 lb-ft20 Nm
- Intake Manifold BoltIf pushrods18 lb-ft25 Nm
- Rocker Arm BoltsTighten with cam lobe pointing away22 lb-ft30 Nm
- Rocker Arm Shaft BoltsTighten evenly in sequence18 lb-ft25 Nm
- Sensor Mounting Bolts8 lb-ft11 Nm
- Valve Cover BoltsTighten in sequence7 lb-ft10 Nm
Serpentine Belt2 specs
- Belt Tensioner Bolt41 lb-ft55 Nm
- Idler Pulley Bolt33 lb-ft45 Nm
Serpentine Belt Tensioner4 specs
- Belt Tensioner Bolt41 lb-ft55 Nm
- Electrical Connector Bolts5 lb-ft7 Nm
- Gasket Surface BoltsClean mating surfaces15 lb-ft20 Nm
- Sensor Mounting Bolts8 lb-ft11 Nm
Short Block Replacement12 specs
- Connecting Rod BoltsTTY - critical torque plus angle33 lb-ft45 Nm
- Crankshaft Pulley BoltOften TTY - check spec, may require impact133 lb-ft180 Nm
- Electrical Connector Bolts5 lb-ft7 Nm
- Flywheel BoltsOften TTY, tighten in star pattern70 lb-ft95 Nm
- Gasket Surface BoltsClean mating surfaces15 lb-ft20 Nm
- Main Bearing Cap BoltsTTY - tighten in sequence plus angle55 lb-ft75 Nm
- Oil Drain PlugUse new crush washer26 lb-ft35 Nm
- Oil Pan Bolt9 lb-ft12 Nm
- Oil Pump Bolts9 lb-ft12 Nm
- Sensor Mounting Bolts8 lb-ft11 Nm
- Timing Cover Bolts - 8mmTighten in sequence18 lb-ft25 Nm
- Transmission-to-Engine Bolts41 lb-ft55 Nm
Throttle Body2 specs
- Air Intake Hose Clamps2 lb-ft3 Nm
- Throttle Body Bolts7 lb-ft10 Nm
Throttle Position Sensor4 specs
- Electrical Connector Bolts5 lb-ft7 Nm
- Gasket Surface BoltsClean mating surfaces15 lb-ft20 Nm
- Sensor Mounting Bolts8 lb-ft11 Nm
- TPS Screws2 lb-ft3 Nm
Timing Chain5 specs
- Camshaft Sprocket Bolts59 lb-ft80 Nm
- Crankshaft Pulley BoltOften TTY - check specs133 lb-ft + 90°180 Nm
- Timing Chain Guide Bolts9 lb-ft12 Nm
- Timing Chain Tensioner18 lb-ft25 Nm
- Timing Cover BoltTighten in sequence9 lb-ft12 Nm
Timing Chain Guide11 specs
- Camshaft Sprocket Bolts55 lb-ft75 Nm
- Crankshaft Pulley Bolt130 lb-ft176 Nm
- Electrical Connector Bolts5 lb-ft7 Nm
- Gasket Surface BoltsClean mating surfaces15 lb-ft20 Nm
- Guide Bolts18 lb-ft24 Nm
- Sensor Mounting Bolts8 lb-ft11 Nm
- Tensioner Bolt15 lb-ft20 Nm
- Timing Chain Guide BoltsReplace if worn9 lb-ft12 Nm
- Timing Cover Bolt10 lb-ft14 Nm
- Timing Cover Bolts - 8mmTighten in sequence18 lb-ft25 Nm
- Valve Cover BoltsTighten in sequence7 lb-ft10 Nm
Timing Chain Kit18 specs
- Cam Phaser BoltApply threadlocker, hold cam stationary48 lb-ft65 Nm
- Camshaft Sprocket BoltsHold cam with wrench on hex59 lb-ft80 Nm
- Crankshaft Pulley BoltOften TTY - check spec, may require impact133 lb-ft180 Nm
- Electrical Connector Bolts5 lb-ft7 Nm
- Gasket Surface BoltsClean mating surfaces15 lb-ft20 Nm
- Guide Bolts18 lb-ft24 Nm
- Oil Drain PlugUse new crush washer26 lb-ft35 Nm
- Oil Pump Bolts9 lb-ft12 Nm
- Sensor Mounting Bolts8 lb-ft11 Nm
- Tensioner Bolt15 lb-ft20 Nm
- Timing Chain Guide BoltsReplace if worn9 lb-ft12 Nm
- Timing Chain Idler Sprocket18 lb-ft25 Nm
- Timing Chain Tensioner BoltInstall with pin/clip to compress18 lb-ft25 Nm
- Timing Cover Bolt10 lb-ft14 Nm
- Timing Cover Bolts - 10mmTighten in sequence33 lb-ft45 Nm
- Timing Cover Bolts - 6mmTighten in sequence7 lb-ft10 Nm
- Timing Cover Bolts - 8mmTighten in sequence18 lb-ft25 Nm
- Valve Cover BoltsTighten in sequence7 lb-ft10 Nm
Timing Chain Tensioner11 specs
- Camshaft Sprocket Bolts55 lb-ft75 Nm
- Crankshaft Pulley Bolt130 lb-ft176 Nm
- Electrical Connector Bolts5 lb-ft7 Nm
- Gasket Surface BoltsClean mating surfaces15 lb-ft20 Nm
- Guide Bolts18 lb-ft24 Nm
- Sensor Mounting Bolts8 lb-ft11 Nm
- Tensioner Bolt15 lb-ft20 Nm
- Timing Chain Tensioner BoltInstall with pin/clip to compress18 lb-ft25 Nm
- Timing Cover Bolt10 lb-ft14 Nm
- Timing Cover Bolts - 8mmTighten in sequence18 lb-ft25 Nm
- Valve Cover BoltsTighten in sequence7 lb-ft10 Nm
Transmission Mount7 specs
- Crossmember Bolt70 lb-ft95 Nm
- Drain PlugUse new washer25 lb-ft34 Nm
- Fill Plug25 lb-ft34 Nm
- Flywheel BoltsOften TTY, tighten in star pattern70 lb-ft95 Nm
- Transmission Drain PlugUse new crush washer if equipped22 lb-ft30 Nm
- Transmission Mount Bolts48 lb-ft65 Nm
- Transmission Pan BoltsTighten in criss-cross pattern9 lb-ft12 Nm
Valve Adjustment6 specs
- Electrical Connector Bolts5 lb-ft7 Nm
- Gasket Surface BoltsClean mating surfaces15 lb-ft20 Nm
- Rocker Arm BoltsTighten with cam lobe pointing away22 lb-ft30 Nm
- Sensor Mounting Bolts8 lb-ft11 Nm
- Valve Cover BoltsTighten in sequence7 lb-ft10 Nm
- Valve Lash Adjusting Screw Lock NutHold screw while tightening15 lb-ft20 Nm
Valve Cover Gasket - Single2 specs
- Spark Plug Tube SealsIf equipped with separate seals9 lb-ft12 Nm
- Valve Cover BoltsTighten in sequence7 lb-ft10 Nm
Valve Cover Gaskets - Both7 specs
- Electrical Connector Bolts5 lb-ft7 Nm
- Gasket Surface BoltsClean mating surfaces15 lb-ft20 Nm
- Ignition Coil Bolt6 lb-ft8 Nm
- Intake Manifold BoltIf required18 lb-ft25 Nm
- Sensor Mounting Bolts8 lb-ft11 Nm
- Spark Plugs - Aluminum HeadApply anti-seize to threads15 lb-ft20 Nm
- Valve Cover BoltsTighten in sequence7 lb-ft10 Nm
Valve Job - Complete12 specs
- Camshaft Cap BoltsTighten in sequence from center outward, multiple passes10 lb-ft14 Nm
- Camshaft Sprocket BoltsHold cam with wrench on hex59 lb-ft80 Nm
- Cylinder Head BoltsTTY - tighten in sequence plus angle48 lb-ft65 Nm
- Electrical Connector Bolts5 lb-ft7 Nm
- Exhaust Manifold NutsApply anti-seize, work hot-to-cold22 lb-ft30 Nm
- Gasket Surface BoltsClean mating surfaces15 lb-ft20 Nm
- Intake Manifold Bolt18 lb-ft25 Nm
- Rocker Arm BoltsTighten with cam lobe pointing away22 lb-ft30 Nm
- Sensor Mounting Bolts8 lb-ft11 Nm
- Timing Chain Tensioner BoltInstall with pin/clip to compress18 lb-ft25 Nm
- Timing Cover Bolts - 8mmTighten in sequence18 lb-ft25 Nm
- Valve Cover BoltsTighten in sequence7 lb-ft10 Nm
Valve Seals8 specs
- Camshaft Cap BoltsTighten in sequence from center outward, multiple passes10 lb-ft14 Nm
- Electrical Connector Bolts5 lb-ft7 Nm
- Gasket Surface BoltsClean mating surfaces15 lb-ft20 Nm
- Rocker Arm BoltsTighten with cam lobe pointing away22 lb-ft30 Nm
- Rocker Arm Shaft BoltsTighten evenly in sequence18 lb-ft25 Nm
- Sensor Mounting Bolts8 lb-ft11 Nm
- Spark Plugs - Aluminum HeadApply anti-seize to threads15 lb-ft20 Nm
- Valve Cover BoltsTighten in sequence7 lb-ft10 Nm
Valve Spring - Single6 specs
- Electrical Connector Bolts5 lb-ft7 Nm
- Gasket Surface BoltsClean mating surfaces15 lb-ft20 Nm
- Rocker Arm BoltsTighten with cam lobe pointing away22 lb-ft30 Nm
- Sensor Mounting Bolts8 lb-ft11 Nm
- Spark Plugs - Aluminum HeadApply anti-seize to threads15 lb-ft20 Nm
- Valve Cover BoltsTighten in sequence7 lb-ft10 Nm
Valve Springs - All8 specs
- Camshaft Cap BoltsTighten in sequence from center outward, multiple passes10 lb-ft14 Nm
- Electrical Connector Bolts5 lb-ft7 Nm
- Gasket Surface BoltsClean mating surfaces15 lb-ft20 Nm
- Rocker Arm BoltsTighten with cam lobe pointing away22 lb-ft30 Nm
- Rocker Arm Shaft BoltsTighten evenly in sequence18 lb-ft25 Nm
- Sensor Mounting Bolts8 lb-ft11 Nm
- Spark Plugs - Aluminum HeadApply anti-seize to threads15 lb-ft20 Nm
- Valve Cover BoltsTighten in sequence7 lb-ft10 Nm
Variable Valve Timing Actuator10 specs
- Cam Phaser BoltApply threadlocker, hold cam stationary48 lb-ft65 Nm
- Camshaft Sprocket BoltsHold cam with wrench on hex59 lb-ft80 Nm
- Crankshaft Pulley BoltOften TTY - check spec, may require impact133 lb-ft180 Nm
- Electrical Connector Bolts5 lb-ft7 Nm
- Gasket Surface BoltsClean mating surfaces15 lb-ft20 Nm
- Sensor Mounting Bolts8 lb-ft11 Nm
- Timing Chain Tensioner BoltInstall with pin/clip to compress18 lb-ft25 Nm
- Timing Cover Bolts - 8mmTighten in sequence18 lb-ft25 Nm
- Valve Cover BoltsTighten in sequence7 lb-ft10 Nm
- VVT Solenoid Bolt7 lb-ft10 Nm
VVT Solenoid - Single5 specs
- Electrical Connector Bolts5 lb-ft7 Nm
- Gasket Surface BoltsClean mating surfaces15 lb-ft20 Nm
- Sensor Mounting Bolts8 lb-ft11 Nm
- Valve Cover BoltsTighten in sequence7 lb-ft10 Nm
- VVT Solenoid Bolt7 lb-ft10 Nm
VVT Solenoids - All6 specs
- Camshaft Position Sensor7 lb-ft10 Nm
- Electrical Connector Bolts5 lb-ft7 Nm
- Gasket Surface BoltsClean mating surfaces15 lb-ft20 Nm
- Sensor Mounting Bolts8 lb-ft11 Nm
- Valve Cover BoltsTighten in sequence7 lb-ft10 Nm
- VVT Solenoid Bolt7 lb-ft10 Nm

Cooling

Coolant Bypass Pipe8 specs
- Bleed ScrewOpen during fill5 lb-ft7 Nm
- Coolant Drain Plug11 lb-ft15 Nm
- Drain PetcockHand tight5 lb-ft7 Nm
- Fan Bolts8 lb-ft11 Nm
- Hose Clamps2 lb-ft3 Nm
- Pump BoltsTorque in sequence18 lb-ft24 Nm
- Thermostat Housing Bolt11 lb-ft15 Nm
- Water Pump BoltsTighten in criss-cross pattern18 lb-ft25 Nm
Coolant Flush12 specs
- Air Box Clips4 lb-ft5 Nm
- Bleed ScrewOpen during fill5 lb-ft7 Nm
- Block Drain PlugIf equipped, use new washer18 lb-ft25 Nm
- Connector Bolts5 lb-ft7 Nm
- Coolant Hose Clamps3 lb-ft4 Nm
- Drain Petcock4 lb-ft5 Nm
- Drain Plug11 lb-ft15 Nm
- Hose Clamps3 lb-ft4 Nm
- Oil Drain PlugUse new crush washer26 lb-ft35 Nm
- Pump Bolts18 lb-ft24 Nm
- Radiator CapHand tight1 lb-ft1 Nm
- Wheel Lug NutsTorque in star pattern80 lb-ft108 Nm
Coolant Reservoir9 specs
- Bleed ScrewOpen during fill5 lb-ft7 Nm
- Coolant Drain Plug11 lb-ft15 Nm
- Drain PetcockHand tight5 lb-ft7 Nm
- Fan Bolts8 lb-ft11 Nm
- Hose Clamps3 lb-ft4 Nm
- Pump BoltsTorque in sequence18 lb-ft24 Nm
- Reservoir Mounting Bolts6 lb-ft8 Nm
- Thermostat Housing Bolt10 lb-ft14 Nm
- Water Pump BoltsTighten in criss-cross pattern18 lb-ft25 Nm
Coolant Temperature Sensor7 specs
- Bleed ScrewOpen during fill5 lb-ft7 Nm
- Coolant Drain Plug11 lb-ft15 Nm
- Drain PetcockHand tight5 lb-ft7 Nm
- Fan Bolts8 lb-ft11 Nm
- Hose Clamps2 lb-ft3 Nm
- Pump BoltsTorque in sequence18 lb-ft24 Nm
- Thermostat Housing Bolt11 lb-ft15 Nm
Cooling Fan Assembly6 specs
- Coolant Drain Plug11 lb-ft15 Nm
- Drain PetcockHand tight5 lb-ft7 Nm
- Fan Bolts8 lb-ft11 Nm
- Hose Clamps2 lb-ft3 Nm
- Pump BoltsTorque in sequence18 lb-ft24 Nm
- Thermostat Housing Bolt11 lb-ft15 Nm
Cooling Fan Clutch5 specs
- Drain PetcockHand tight5 lb-ft7 Nm
- Fan Bolts8 lb-ft11 Nm
- Hose Clamps2 lb-ft3 Nm
- Pump Bolts18 lb-ft24 Nm
- Thermostat Housing Bolt11 lb-ft15 Nm
Cooling Fan Motor7 specs
- Drain PetcockHand tight5 lb-ft7 Nm
- Electrical Connector4 lb-ft5 Nm
- Fan Bolts8 lb-ft11 Nm
- Fan Motor Bolts6 lb-ft8 Nm
- Hose ClampsDo not overtighten3 lb-ft4 Nm
- Pump Bolts18 lb-ft24 Nm
- Thermostat Housing Bolt10 lb-ft14 Nm
Cooling Fan Relay4 specs
- Drain PetcockHand tight5 lb-ft7 Nm
- Fan Bolts8 lb-ft11 Nm
- Pump BoltsTorque in sequence18 lb-ft24 Nm
- Thermostat Housing Bolt11 lb-ft15 Nm
Engine Oil Cooler6 specs
- Coolant Drain Plug11 lb-ft15 Nm
- Drain PetcockHand tight5 lb-ft7 Nm
- Fan Bolts8 lb-ft11 Nm
- Hose Clamps2 lb-ft3 Nm
- Pump Bolts18 lb-ft24 Nm
- Thermostat Housing Bolt11 lb-ft15 Nm
Heater Control Valve6 specs
- Drain PetcockHand tight5 lb-ft7 Nm
- Fan Bolts8 lb-ft11 Nm
- Hose Clamps2 lb-ft3 Nm
- Pump Bolts18 lb-ft24 Nm
- Thermostat Housing Bolt10 lb-ft14 Nm
- Valve Mounting6 lb-ft8 Nm
Heater Core8 specs
- Dashboard Screws2 lb-ft3 Nm
- Drain PetcockHand tight5 lb-ft7 Nm
- Fan Bolts8 lb-ft11 Nm
- Heater Core Mounting6 lb-ft8 Nm
- Heater Hose Clamps2 lb-ft3 Nm
- Hose ClampsDo not overtighten3 lb-ft4 Nm
- Pump BoltsTorque in sequence18 lb-ft24 Nm
- Thermostat Housing Bolt10 lb-ft14 Nm
Heater Hoses6 specs
- Coolant Drain Plug11 lb-ft15 Nm
- Drain PetcockHand tight5 lb-ft7 Nm
- Fan Bolts8 lb-ft11 Nm
- Hose Clamps2 lb-ft3 Nm
- Pump Bolts18 lb-ft24 Nm
- Thermostat Housing Bolt11 lb-ft15 Nm
Radiator4 specs
- Drain PetcockPlastic - hand tight4 lb-ft5 Nm
- Radiator Mounting BoltDo not overtighten plastic mounts9 lb-ft12 Nm
- Transmission Cooler LinesIf equipped18 lb-ft25 Nm
- Upper/Lower Hose Clamps2 lb-ft3 Nm
Radiator Cap4 specs
- Drain PetcockHand tight5 lb-ft7 Nm
- Fan Bolts8 lb-ft11 Nm
- Pump Bolts18 lb-ft24 Nm
- Thermostat Housing Bolt11 lb-ft15 Nm
Radiator Hose - Lower5 specs
- Drain PetcockHand tight5 lb-ft7 Nm
- Fan Bolts8 lb-ft11 Nm
- Hose Clamps2 lb-ft3 Nm
- Pump Bolts18 lb-ft24 Nm
- Thermostat Housing Bolt10 lb-ft14 Nm
Radiator Hose - Upper5 specs
- Drain PetcockHand tight5 lb-ft7 Nm
- Fan Bolts8 lb-ft11 Nm
- Hose Clamps2 lb-ft3 Nm
- Pump BoltsTorque in sequence18 lb-ft24 Nm
- Thermostat Housing Bolt10 lb-ft14 Nm
Radiator Hoses - Both6 specs
- Coolant Drain Plug11 lb-ft15 Nm
- Drain PetcockHand tight5 lb-ft7 Nm
- Fan Bolts8 lb-ft11 Nm
- Hose Clamps2 lb-ft3 Nm
- Pump BoltsTorque in sequence18 lb-ft24 Nm
- Thermostat Housing Bolt11 lb-ft15 Nm
Radiator Removal and Service4 specs
- Drain PetcockPlastic - hand-tight only4 lb-ft5 Nm
- Fan Shroud Bolts7 lb-ft10 Nm
- Radiator Mounting BoltDo not overtighten plastic mounts9 lb-ft12 Nm
- Transmission Cooler LinesIf equipped, use new washers18 lb-ft25 Nm
Thermostat2 specs
- Coolant Temperature SensorUse thread sealant15 lb-ft20 Nm
- Thermostat Housing Bolt11 lb-ft15 Nm
Thermostat Housing8 specs
- Coolant Drain Plug11 lb-ft15 Nm
- Coolant Hose Clamps3 lb-ft4 Nm
- Drain PetcockHand tight5 lb-ft7 Nm
- Fan Bolts8 lb-ft11 Nm
- Hose Clamps2 lb-ft3 Nm
- Pump BoltsTorque in sequence18 lb-ft24 Nm
- Thermostat Housing Bolt11 lb-ft15 Nm
- Water Pump BoltsTighten in criss-cross pattern18 lb-ft25 Nm
Water Pump3 specs
- Hose ClampsSpring clamps preferred2 lb-ft3 Nm
- Thermostat Housing Bolt11 lb-ft15 Nm
- Water Pump BoltsTighten in criss-cross pattern18 lb-ft25 Nm

Ignition

Ignition Coil - Single3 specs
- Connector Bolts5 lb-ft7 Nm
- Ignition Coil Bolt6 lb-ft8 Nm
- Spark Plugs - Aluminum HeadApply anti-seize to threads15 lb-ft20 Nm
Ignition Coils - All3 specs
- Connector Bolts5 lb-ft7 Nm
- Ignition Coil Bolt6 lb-ft8 Nm
- Spark Plugs - Aluminum HeadApply anti-seize to threads15 lb-ft20 Nm
Ignition Control Module2 specs
- Connector Bolts5 lb-ft7 Nm
- Ignition Coil Bolt6 lb-ft8 Nm
Ignition Lock Cylinder2 specs
- Connector Bolts5 lb-ft7 Nm
- Ignition Coil Bolt6 lb-ft8 Nm
Ignition Switch3 specs
- Connector Bolts5 lb-ft7 Nm
- Steering Column Bolts22 lb-ft30 Nm
- Switch Mounting Screws4 lb-ft5 Nm
Spark Plugs9 specs
- Air Box Clips4 lb-ft5 Nm
- Connector Bolts5 lb-ft7 Nm
- Engine Cover Clips2 lb-ft3 Nm
- Ignition Coil Bolt6 lb-ft8 Nm
- Oil Drain PlugUse new crush washer26 lb-ft35 Nm
- Spark PlugGap before install15 lb-ft20 Nm
- Spark Plugs - Aluminum HeadApply anti-seize to threads15 lb-ft20 Nm
- Spark Plugs - Cast Iron HeadApply anti-seize to threads22 lb-ft30 Nm
- Wheel Lug NutsTorque in star pattern80 lb-ft108 Nm

Fuel system

Charcoal Canister5 specs
- Filter Bracket8 lb-ft11 Nm
- Fuel Line FittingsUse new O-rings18 lb-ft25 Nm
- Hose Clamps2 lb-ft3 Nm
- Pressure Regulator Screws5 lb-ft7 Nm
- Pump Mounting10 lb-ft14 Nm
EVAP Purge Valve4 specs
- Filter Bracket8 lb-ft11 Nm
- Hose Clamps2 lb-ft3 Nm
- Pressure Regulator Screws5 lb-ft7 Nm
- Pump Mounting10 lb-ft14 Nm
EVAP Vent Valve4 specs
- Filter Bracket8 lb-ft11 Nm
- Hose Clamps2 lb-ft3 Nm
- Pressure Regulator Screws5 lb-ft7 Nm
- Pump Mounting10 lb-ft14 Nm
Fuel Cap3 specs
- Filter Bracket8 lb-ft11 Nm
- Pressure Regulator Screws5 lb-ft7 Nm
- Pump Mounting10 lb-ft14 Nm
Fuel Filler Neck6 specs
- Filler Neck Bolts7 lb-ft10 Nm
- Filter Bracket8 lb-ft11 Nm
- Fuel Rail Bolts15 lb-ft20 Nm
- Hose Clamps2 lb-ft3 Nm
- Pressure Regulator Screws5 lb-ft7 Nm
- Pump Mounting10 lb-ft14 Nm
Fuel Filter7 specs
- Air Box Clips4 lb-ft5 Nm
- Connector Bolts5 lb-ft7 Nm
- Filter Bracket Bolt10 lb-ft14 Nm
- Fuel Filter Bracket Bolt7 lb-ft10 Nm
- Fuel Line FittingsIf threaded type18 lb-ft25 Nm
- Oil Drain PlugUse new crush washer26 lb-ft35 Nm
- Wheel Lug NutsTorque in star pattern80 lb-ft108 Nm
Fuel Filter - In-Tank6 specs
- Filter Bracket8 lb-ft11 Nm
- Filter Bracket Bolt10 lb-ft14 Nm
- Fuel Line FittingsUse new O-rings18 lb-ft25 Nm
- Hose Clamps2 lb-ft3 Nm
- Pressure Regulator Screws5 lb-ft7 Nm
- Pump Mounting10 lb-ft14 Nm
Fuel Injector - Single6 specs
- Filter Bracket8 lb-ft11 Nm
- Fuel Line FittingsUse new O-rings18 lb-ft25 Nm
- Fuel Rail Bolts9 lb-ft12 Nm
- Hose Clamps2 lb-ft3 Nm
- Pressure Regulator Screws5 lb-ft7 Nm
- Pump Mounting10 lb-ft14 Nm
Fuel Injector Cleaning6 specs
- Filter Bracket8 lb-ft11 Nm
- Fuel Line FittingsUse new O-rings18 lb-ft25 Nm
- Fuel Rail Bolts9 lb-ft12 Nm
- Hose Clamps2 lb-ft3 Nm
- Pressure Regulator Screws5 lb-ft7 Nm
- Pump Mounting10 lb-ft14 Nm
Fuel Injectors - All6 specs
- Filter Bracket8 lb-ft11 Nm
- Fuel Line FittingsUse new O-rings18 lb-ft25 Nm
- Fuel Rail Bolts9 lb-ft12 Nm
- Hose Clamps2 lb-ft3 Nm
- Pressure Regulator Screws5 lb-ft7 Nm
- Pump Mounting10 lb-ft14 Nm
Fuel Level Sensor5 specs
- Filter Bracket8 lb-ft11 Nm
- Fuel Line FittingsUse new O-rings18 lb-ft25 Nm
- Hose Clamps2 lb-ft3 Nm
- Pressure Regulator Screws5 lb-ft7 Nm
- Pump Mounting10 lb-ft14 Nm
Fuel Line - High Pressure6 specs
- Filter Bracket8 lb-ft11 Nm
- Fuel Line FittingsUse new O-rings18 lb-ft25 Nm
- Fuel Rail Bolts9 lb-ft12 Nm
- Hose Clamps2 lb-ft3 Nm
- Pressure Regulator Screws5 lb-ft7 Nm
- Pump Mounting10 lb-ft14 Nm
Fuel Line - Return6 specs
- Filter Bracket8 lb-ft11 Nm
- Fuel Line FittingsUse new O-rings18 lb-ft25 Nm
- Fuel Rail Bolts9 lb-ft12 Nm
- Hose Clamps2 lb-ft3 Nm
- Pressure Regulator Screws5 lb-ft7 Nm
- Pump Mounting10 lb-ft14 Nm
Fuel Pressure Regulator6 specs
- Filter Bracket8 lb-ft11 Nm
- Fuel Line18 lb-ft25 Nm
- Fuel Rail Bolts15 lb-ft20 Nm
- Pressure Regulator Screws5 lb-ft7 Nm
- Pump Mounting10 lb-ft14 Nm
- Regulator Mounting Screws4 lb-ft5 Nm
Fuel Pump2 specs
- Fuel Pump Module Lock RingUse special tool59 lb-ft80 Nm
- Tank Strap Bolts26 lb-ft35 Nm
Fuel Pump Module7 specs
- Access Cover Screws3 lb-ft4 Nm
- Filter Bracket8 lb-ft11 Nm
- Fuel Line FittingsUse new O-rings18 lb-ft25 Nm
- Fuel Pump Lock RingLock ring tool50 lb-ft68 Nm
- Hose Clamps2 lb-ft3 Nm
- Pressure Regulator Screws5 lb-ft7 Nm
- Pump Mounting10 lb-ft14 Nm
Fuel Rail6 specs
- Filter Bracket8 lb-ft11 Nm
- Fuel Line FittingsUse new O-rings18 lb-ft25 Nm
- Fuel Rail Bolts9 lb-ft12 Nm
- Hose Clamps2 lb-ft3 Nm
- Pressure Regulator Screws5 lb-ft7 Nm
- Pump Mounting10 lb-ft14 Nm
Fuel Tank7 specs
- Filler Neck Clamp3 lb-ft4 Nm
- Filter Bracket8 lb-ft11 Nm
- Fuel Line FittingsUse new O-rings18 lb-ft25 Nm
- Fuel Rail Bolts15 lb-ft20 Nm
- Pressure Regulator Screws5 lb-ft7 Nm
- Pump Mounting10 lb-ft14 Nm
- Tank Strap Bolts26 lb-ft35 Nm
Fuel Tank Strap5 specs
- Filter Bracket8 lb-ft11 Nm
- Fuel Line FittingsUse new O-rings18 lb-ft25 Nm
- Hose Clamps2 lb-ft3 Nm
- Pressure Regulator Screws5 lb-ft7 Nm
- Pump Mounting10 lb-ft14 Nm
High Pressure Fuel Pump5 specs
- Filter Bracket8 lb-ft11 Nm
- Fuel Line FittingsUse new O-rings18 lb-ft25 Nm
- Hose Clamps2 lb-ft3 Nm
- Pressure Regulator Screws5 lb-ft7 Nm
- Pump Mounting10 lb-ft14 Nm

Electrical

Airbag - Driver5 specs
- Airbag Module BoltsTorx - disconnect battery and wait 2 minutes5 lb-ft7 Nm
- Battery Terminal Bolts5 lb-ft7 Nm
- Connector Screws3 lb-ft4 Nm
- Ground Strap BoltsClean contact surfaces10 lb-ft14 Nm
- Steering Wheel Nut40 lb-ft54 Nm
Airbag - Passenger5 specs
- Airbag Module BoltsTorx - disconnect battery and wait 2 minutes5 lb-ft7 Nm
- Battery Terminal Bolts5 lb-ft7 Nm
- Connector Screws3 lb-ft4 Nm
- Dashboard Fasteners3 lb-ft4 Nm
- Ground Strap BoltsClean contact surfaces10 lb-ft14 Nm
Airbag - Side5 specs
- Battery Terminal Bolts5 lb-ft7 Nm
- Connector Screws3 lb-ft4 Nm
- Ground Strap BoltsClean contact surfaces10 lb-ft14 Nm
- Seat Mounting BoltsSafety critical45 lb-ft61 Nm
- Side Airbag Module BoltsTorx5 lb-ft7 Nm
Airbag Module/Computer4 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
- Module Mounting Bolts6 lb-ft8 Nm
- Sensor Mounting Bolts7 lb-ft10 Nm
Alternator4 specs
- Alternator Mounting Bolts37 lb-ft50 Nm
- Alternator Pivot Bolt18 lb-ft25 Nm
- Battery Terminal BoltsDo not overtighten6 lb-ft8 Nm
- Serpentine Belt Tensioner41 lb-ft55 Nm
Alternator Belt4 specs
- Alternator Mounting Bolts35 lb-ft47 Nm
- Alternator Pivot Bolt35 lb-ft47 Nm
- Battery Cable Nut10 lb-ft14 Nm
- Connector Screws3 lb-ft4 Nm
Amplifier4 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
- Ground Strap BoltsEnsure clean contact9 lb-ft12 Nm
- Module Mounting Bolts6 lb-ft8 Nm
Antenna2 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
Backup Camera4 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
- Module Mounting Bolts6 lb-ft8 Nm
- Sensor Mounting Bolts7 lb-ft10 Nm
Battery3 specs
- Battery Hold-Down Bolt6 lb-ft8 Nm
- Battery Terminal BoltsDo not overtighten - can crack terminal4 lb-ft6 Nm
- Battery Tray Bolts9 lb-ft12 Nm
Battery Cable - Negative6 specs
- Battery Hold-Down BoltDo not overtighten8 lb-ft11 Nm
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
- Ground Cable Bolt10 lb-ft14 Nm
- Ground Strap BoltsEnsure clean contact9 lb-ft12 Nm
- Sensor Mounting Bolts7 lb-ft10 Nm
Battery Cable - Positive5 specs
- Battery Hold-Down BoltDo not overtighten8 lb-ft11 Nm
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
- Ground Cable Bolt10 lb-ft14 Nm
- Module Mounting Bolts6 lb-ft8 Nm
Battery Cables - Both6 specs
- Battery Hold-Down BoltDo not overtighten8 lb-ft11 Nm
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
- Ground Cable Bolt10 lb-ft14 Nm
- Ground Strap BoltsEnsure clean contact9 lb-ft12 Nm
- Sensor Mounting Bolts7 lb-ft10 Nm
Battery Terminal6 specs
- Battery Hold-Down BoltDo not overtighten8 lb-ft11 Nm
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
- Ground Cable Bolt10 lb-ft14 Nm
- Ground Strap BoltsEnsure clean contact9 lb-ft12 Nm
- Sensor Mounting Bolts7 lb-ft10 Nm
Blower Motor2 specs
- Blower Motor Mounting Screw3 lb-ft4 Nm
- Blower Motor Resistor Screws1.5 lb-ft2 Nm
Blower Motor Control Module3 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
- Module Mounting Bolts6 lb-ft8 Nm
Blower Motor Resistor4 specs
- Battery Terminal Bolts5 lb-ft7 Nm
- Connector Screws3 lb-ft4 Nm
- Ground Strap BoltsClean contact surfaces10 lb-ft14 Nm
- Resistor Screws1.5 lb-ft2 Nm
Clock Spring7 specs
- Airbag Module BoltsTorx - disconnect battery first5 lb-ft7 Nm
- Battery Terminal Bolts5 lb-ft7 Nm
- Clock Spring ScrewsAlign marks before removal3 lb-ft4 Nm
- Connector Screws3 lb-ft4 Nm
- Ground Strap BoltsClean contact surfaces10 lb-ft14 Nm
- Steering Column CoversPlastic clips2 lb-ft3 Nm
- Steering Wheel Nut40 lb-ft54 Nm
Combination Switch4 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
- Module Mounting Bolts6 lb-ft8 Nm
- Sensor Mounting Bolts7 lb-ft10 Nm
Dimmer Switch3 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
- Module Mounting Bolts6 lb-ft8 Nm
Door Lock Actuator - Front2 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
Door Lock Actuator - Rear2 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
Fog Light Assembly2 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
Fog Light Bulb1 spec
- Connector Screws3 lb-ft4 Nm
Fuel Pump Relay6 specs
- Access Cover Screws3 lb-ft4 Nm
- Battery Terminal Bolts5 lb-ft7 Nm
- Connector Screws3 lb-ft4 Nm
- Fuel Pump Lock RingLock ring tool50 lb-ft68 Nm
- Ground Strap BoltsClean contact surfaces10 lb-ft14 Nm
- Relay Socket4 lb-ft5 Nm
Fuse Box - Engine Bay4 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
- Ground Strap BoltsEnsure clean contact9 lb-ft12 Nm
- Module Mounting Bolts6 lb-ft8 Nm
Fuse Box - Interior4 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
- Ground Strap BoltsEnsure clean contact9 lb-ft12 Nm
- Module Mounting Bolts6 lb-ft8 Nm
Headlight Assembly5 specs
- Adjuster Screws2 lb-ft3 Nm
- Battery Terminal Bolts5 lb-ft7 Nm
- Connector Screws3 lb-ft4 Nm
- Ground Strap BoltsClean contact surfaces10 lb-ft14 Nm
- Headlight Assembly Bolts7 lb-ft10 Nm
Headlight Bulb - Single4 specs
- Battery Terminal Bolts5 lb-ft7 Nm
- Bulb Retaining Ring4 lb-ft5 Nm
- Connector Screws3 lb-ft4 Nm
- Ground Strap BoltsClean contact surfaces10 lb-ft14 Nm
Headlight Bulbs - Pair1 spec
- Connector Screws3 lb-ft4 Nm
Headlight Switch3 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
- Module Mounting Bolts6 lb-ft8 Nm
Heated Seat Module3 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
- Module Mounting Bolts6 lb-ft8 Nm
HID Ballast3 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
- Module Mounting Bolts6 lb-ft8 Nm
Horn4 specs
- Battery Terminal Bolts5 lb-ft7 Nm
- Connector Screws3 lb-ft4 Nm
- Ground Strap BoltsClean contact surfaces10 lb-ft14 Nm
- Horn Mounting Bolt11 lb-ft15 Nm
Horn Relay2 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
Instrument Cluster3 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
- Module Mounting Bolts6 lb-ft8 Nm
LED Headlight Module3 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
- Module Mounting Bolts6 lb-ft8 Nm
Main Relay3 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
- Module Mounting Bolts6 lb-ft8 Nm
Power Antenna Motor2 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
Power Mirror Motor2 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
Power Seat Motor3 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
- Module Mounting Bolts6 lb-ft8 Nm
Power Window Motor - Front3 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
- Module Mounting Bolts6 lb-ft8 Nm
Power Window Motor - Rear3 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
- Module Mounting Bolts6 lb-ft8 Nm
Power Window Regulator - Front3 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
- Module Mounting Bolts6 lb-ft8 Nm
Power Window Regulator - Rear2 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
Radio/Head Unit3 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
- Module Mounting Bolts6 lb-ft8 Nm
Relay - Generic3 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
- Module Mounting Bolts6 lb-ft8 Nm
Seat Heater Element4 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
- Module Mounting Bolts6 lb-ft8 Nm
- Sensor Mounting Bolts7 lb-ft10 Nm
Side Mirror Assembly2 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
Speaker - Dash3 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
- Sensor Mounting Bolts7 lb-ft10 Nm
Speaker - Door2 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
Speedometer4 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
- Module Mounting Bolts6 lb-ft8 Nm
- Sensor Mounting Bolts7 lb-ft10 Nm
Starter3 specs
- Heat Shield BoltsIf equipped7 lb-ft10 Nm
- Starter Mounting BoltLong bolt may need extension37 lb-ft50 Nm
- Starter Solenoid NutFor B+ cable9 lb-ft12 Nm
Starter Solenoid4 specs
- Battery Cable Nut10 lb-ft14 Nm
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
- Starter Mounting Bolt35 lb-ft47 Nm
Subwoofer3 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
- Module Mounting Bolts6 lb-ft8 Nm
Sunroof Motor3 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
- Module Mounting Bolts6 lb-ft8 Nm
Sunroof Switch2 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
Tail Light Assembly5 specs
- Battery Terminal Bolts5 lb-ft7 Nm
- Connector Screws3 lb-ft4 Nm
- Ground Strap BoltsClean contact surfaces10 lb-ft14 Nm
- Lens Screws1.5 lb-ft2 Nm
- Tail Light Bolts6 lb-ft8 Nm
Tail Light Bulb1 spec
- Connector Screws3 lb-ft4 Nm
Third Brake Light1 spec
- Connector Screws3 lb-ft4 Nm
Trunk/Liftgate Actuator2 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
Turn Signal Bulb - Front1 spec
- Connector Screws3 lb-ft4 Nm
Turn Signal Bulb - Rear1 spec
- Connector Screws3 lb-ft4 Nm
Turn Signal Switch5 specs
- Battery Terminal Bolts5 lb-ft7 Nm
- Connector Screws3 lb-ft4 Nm
- Ground Strap BoltsClean contact surfaces10 lb-ft14 Nm
- Steering Column Covers1.5 lb-ft2 Nm
- Switch Mounting Screws2 lb-ft3 Nm
Voltage Regulator3 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
- Module Mounting Bolts6 lb-ft8 Nm
Washer Pump2 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
Washer Reservoir3 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
- Sensor Mounting Bolts7 lb-ft10 Nm
Window Motor and Regulator - Front3 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
- Module Mounting Bolts6 lb-ft8 Nm
Window Motor and Regulator - Rear3 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
- Module Mounting Bolts6 lb-ft8 Nm
Wiper Linkage7 specs
- Battery Terminal Bolts5 lb-ft7 Nm
- Connector Screws3 lb-ft4 Nm
- Ground Strap BoltsEnsure clean contact9 lb-ft12 Nm
- Linkage Pivot Nuts9 lb-ft12 Nm
- Module Mounting Bolts6 lb-ft8 Nm
- Motor Mounting Bolts7 lb-ft10 Nm
- Sensor Mounting Bolts7 lb-ft10 Nm
Wiper Motor - Front3 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
- Module Mounting Bolts6 lb-ft8 Nm
Wiper Motor - Rear2 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm
Wiper Switch2 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws3 lb-ft4 Nm

Suspension

Ball Joint - Lower7 specs
- Control Arm BoltsTorque with vehicle weight on wheels122 lb-ft165 Nm
- Lower Ball Joint NutUse new cotter pin65 lb-ft88 Nm
- Pinch BoltNew bolt45 lb-ft61 Nm
- Strut Bolts85 lb-ft115 Nm
- Sway Bar Link45 lb-ft61 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug NutsTorque in star pattern80 lb-ft108 Nm
Ball Joints - Upper and Lower8 specs
- Control Arm BoltsTorque with vehicle weight on wheels122 lb-ft165 Nm
- Lower Ball Joint NutUse new cotter pin65 lb-ft88 Nm
- Pinch BoltNew bolt45 lb-ft61 Nm
- Strut Bolts85 lb-ft115 Nm
- Strut Tower Nuts37 lb-ft50 Nm
- Sway Bar Link45 lb-ft61 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug Nuts80 lb-ft108 Nm
Coil Spring - Front6 specs
- Control Arm BoltsTorque with vehicle weight on wheels122 lb-ft165 Nm
- Strut Bolts85 lb-ft115 Nm
- Strut Tower Nuts37 lb-ft50 Nm
- Sway Bar Link45 lb-ft61 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug Nuts80 lb-ft108 Nm
Coil Spring - Rear3 specs
- Sway Bar Link45 lb-ft61 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug Nuts80 lb-ft108 Nm
Coil Springs - Front Pair6 specs
- Control Arm BoltsTorque with vehicle weight on wheels122 lb-ft165 Nm
- Strut Bolts85 lb-ft115 Nm
- Strut Tower Nuts37 lb-ft50 Nm
- Sway Bar Link45 lb-ft61 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug NutsTorque in star pattern80 lb-ft108 Nm
Coil Springs - Rear Pair3 specs
- Sway Bar Link45 lb-ft61 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug Nuts80 lb-ft108 Nm
Control Arm Bushing - Front Lower6 specs
- Control Arm BoltsTorque with vehicle weight on wheels122 lb-ft165 Nm
- Lower Ball Joint NutUse new cotter pin65 lb-ft88 Nm
- Strut Bolts85 lb-ft115 Nm
- Sway Bar Link45 lb-ft61 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug NutsTorque in star pattern80 lb-ft108 Nm
Control Arm Bushing - Rear3 specs
- Sway Bar Link45 lb-ft61 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug NutsTorque in star pattern80 lb-ft108 Nm
Front Struts - Pair7 specs
- Control Arm BoltsTorque with vehicle weight on wheels122 lb-ft165 Nm
- Strut Bolts85 lb-ft115 Nm
- Strut to Knuckle Bolts90 lb-ft122 Nm
- Strut Tower Nuts37 lb-ft50 Nm
- Sway Bar Link45 lb-ft61 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug Nuts80 lb-ft108 Nm
Front Suspension Rebuild4 specs
- Ball Joint Pinch BoltUse new bolt if locknut style37 lb-ft50 Nm
- Lower Control Arm BoltsTorque at ride height81 lb-ft110 Nm
- Strut Top Mount Nuts18 lb-ft25 Nm
- Sway Bar End Link Nuts44 lb-ft60 Nm
Knuckle/Spindle - Front7 specs
- Control Arm BoltsTorque with vehicle weight on wheels122 lb-ft165 Nm
- Lower Ball Joint Nut65 lb-ft88 Nm
- Strut Bolts85 lb-ft115 Nm
- Strut Tower Nuts37 lb-ft50 Nm
- Sway Bar Link45 lb-ft61 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug Nuts80 lb-ft108 Nm
Lateral Arm5 specs
- Control Arm BoltsTorque with vehicle weight on wheels122 lb-ft165 Nm
- Strut Bolts85 lb-ft115 Nm
- Sway Bar Link45 lb-ft61 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug Nuts80 lb-ft108 Nm
Lower Control Arm - Front6 specs
- Control Arm BoltsTorque with vehicle weight on wheels122 lb-ft165 Nm
- Lower Ball Joint Nut65 lb-ft88 Nm
- Strut Bolts85 lb-ft115 Nm
- Sway Bar Link45 lb-ft61 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug Nuts80 lb-ft108 Nm
Radius Arm5 specs
- Control Arm BoltsTorque with vehicle weight on wheels122 lb-ft165 Nm
- Strut Bolts85 lb-ft115 Nm
- Sway Bar Link45 lb-ft61 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug Nuts80 lb-ft108 Nm
Radius Arm Bushing5 specs
- Control Arm BoltsTorque with vehicle weight on wheels122 lb-ft165 Nm
- Strut Bolts85 lb-ft115 Nm
- Sway Bar Link45 lb-ft61 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug NutsTorque in star pattern80 lb-ft108 Nm
Rear Shocks - Pair3 specs
- Sway Bar Link45 lb-ft61 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug NutsTorque in star pattern80 lb-ft108 Nm
Rear Suspension Service3 specs
- Shock Lower Bolt52 lb-ft70 Nm
- Sway Bar End Link Nuts37 lb-ft50 Nm
- Trailing Arm BoltsTorque at ride height88 lb-ft120 Nm
Shock Absorber Replacement2 specs
- Lower Mount Bolt66 lb-ft90 Nm
- Upper Mount NutUse new self-locking nut41 lb-ft55 Nm
Strut Bearing6 specs
- Strut Bolts85 lb-ft115 Nm
- Strut to Knuckle Bolts90 lb-ft122 Nm
- Strut Tower Nuts37 lb-ft50 Nm
- Sway Bar Link45 lb-ft61 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug Nuts80 lb-ft108 Nm
Strut Mount - Front6 specs
- Strut Bolts85 lb-ft115 Nm
- Strut to Knuckle Bolts90 lb-ft122 Nm
- Strut Tower Nuts37 lb-ft50 Nm
- Sway Bar Link45 lb-ft61 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug NutsTorque in star pattern80 lb-ft108 Nm
Subframe6 specs
- Control Arm BoltsTorque with vehicle weight on wheels122 lb-ft165 Nm
- Strut Bolts85 lb-ft115 Nm
- Strut Tower Nuts37 lb-ft50 Nm
- Sway Bar Link45 lb-ft61 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug NutsTorque in star pattern80 lb-ft108 Nm
Subframe Bushing6 specs
- Control Arm BoltsTorque with vehicle weight on wheels122 lb-ft165 Nm
- Strut Bolts85 lb-ft115 Nm
- Strut Tower Nuts37 lb-ft50 Nm
- Sway Bar Link45 lb-ft61 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug NutsTorque in star pattern80 lb-ft108 Nm
Sway Bar - Front5 specs
- Strut Bolts85 lb-ft115 Nm
- Sway Bar Bracket Bolts35 lb-ft47 Nm
- Sway Bar Link45 lb-ft61 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug NutsTorque in star pattern80 lb-ft108 Nm
Sway Bar - Rear4 specs
- Sway Bar Bracket Bolts35 lb-ft47 Nm
- Sway Bar Link45 lb-ft61 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug NutsTorque in star pattern80 lb-ft108 Nm
Sway Bar Bushing - Front5 specs
- Strut Bolts85 lb-ft115 Nm
- Sway Bar Bracket Bolts35 lb-ft47 Nm
- Sway Bar Link45 lb-ft61 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug NutsTorque in star pattern80 lb-ft108 Nm
Sway Bar Bushing - Rear4 specs
- Sway Bar Bracket Bolts35 lb-ft47 Nm
- Sway Bar Link45 lb-ft61 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug NutsTorque in star pattern80 lb-ft108 Nm
Sway Bar Link - Front5 specs
- Strut Bolts85 lb-ft115 Nm
- Sway Bar Bracket Bolts35 lb-ft47 Nm
- Sway Bar Link45 lb-ft61 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug NutsTorque in star pattern80 lb-ft108 Nm
Sway Bar Link - Rear4 specs
- Sway Bar Bracket Bolts35 lb-ft47 Nm
- Sway Bar Link45 lb-ft61 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug NutsTorque in star pattern80 lb-ft108 Nm
Sway Bar Links - Front Pair5 specs
- Strut Bolts85 lb-ft115 Nm
- Sway Bar Bracket Bolts35 lb-ft47 Nm
- Sway Bar Link45 lb-ft61 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug NutsTorque in star pattern80 lb-ft108 Nm
Torsion Bar5 specs
- Control Arm BoltsTorque with vehicle weight on wheels122 lb-ft165 Nm
- Strut Bolts85 lb-ft115 Nm
- Sway Bar Link45 lb-ft61 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug Nuts80 lb-ft108 Nm
Torsion Bar Adjustment3 specs
- Strut Bolts85 lb-ft115 Nm
- Sway Bar Link45 lb-ft61 Nm
- Wheel Lug Nuts80 lb-ft108 Nm
Trailing Arm5 specs
- Control Arm BoltsTorque with vehicle weight on wheels122 lb-ft165 Nm
- Strut Bolts85 lb-ft115 Nm
- Sway Bar Link45 lb-ft61 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug NutsTorque in star pattern80 lb-ft108 Nm
Trailing Arm Bushing5 specs
- Control Arm BoltsTorque with vehicle weight on wheels122 lb-ft165 Nm
- Strut Bolts85 lb-ft115 Nm
- Sway Bar Link45 lb-ft61 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug Nuts80 lb-ft108 Nm

Steering

Electric Power Steering Module5 specs
- Coupling Bolt25 lb-ft34 Nm
- Steering Rack Bolts74 lb-ft100 Nm
- Tie Rod End NutUse new cotter pin40 lb-ft54 Nm
- Tie Rod Nut40 lb-ft54 Nm
- Wheel Lug Nuts80 lb-ft108 Nm
Electric Power Steering Motor6 specs
- Coupling Bolt25 lb-ft34 Nm
- Steering Rack Bolts74 lb-ft100 Nm
- Tie Rod End Castle NutUse new cotter pin41 lb-ft55 Nm
- Tie Rod End NutUse new cotter pin40 lb-ft54 Nm
- Tie Rod Nut40 lb-ft54 Nm
- Wheel Lug Nuts80 lb-ft108 Nm
Power Steering Hose - High Pressure6 specs
- Coupling Bolt25 lb-ft34 Nm
- Power Steering Line FittingsUse new O-rings22 lb-ft30 Nm
- Steering Rack Bolts74 lb-ft100 Nm
- Tie Rod End NutUse new cotter pin40 lb-ft54 Nm
- Tie Rod Nut40 lb-ft54 Nm
- Wheel Lug Nuts80 lb-ft108 Nm
Power Steering Hose - Return6 specs
- Coupling Bolt25 lb-ft34 Nm
- Power Steering Line FittingsUse new O-rings22 lb-ft30 Nm
- Steering Rack Bolts74 lb-ft100 Nm
- Tie Rod End NutUse new cotter pin40 lb-ft54 Nm
- Tie Rod Nut40 lb-ft54 Nm
- Wheel Lug Nuts80 lb-ft108 Nm
Power Steering Rack9 specs
- Coupling Bolt25 lb-ft34 Nm
- Power Steering Line FittingsUse new O-rings. Verify sequence with the service manual22 lb-ft30 Nm
- Pressure Line FittingNew O-ring25 lb-ft34 Nm
- Pump Mounting Bolts20 lb-ft27 Nm
- Steering Rack BoltsVerify sequence with the service manual74 lb-ft100 Nm
- Tie Rod End Castle NutUse new cotter pin. Verify sequence with the service manual41 lb-ft55 Nm
- Tie Rod End NutUse new cotter pin40 lb-ft54 Nm
- Tie Rod Nut40 lb-ft54 Nm
- Wheel Lug Nuts80 lb-ft108 Nm
Power Steering Reservoir5 specs
- Coupling Bolt25 lb-ft34 Nm
- Power Steering Line FittingsUse new O-rings22 lb-ft30 Nm
- Tie Rod End NutUse new cotter pin40 lb-ft54 Nm
- Tie Rod Nut40 lb-ft54 Nm
- Wheel Lug Nuts80 lb-ft108 Nm
Rack and Pinion Boots5 specs
- Coupling Bolt25 lb-ft34 Nm
- Tie Rod End Castle NutUse new cotter pin41 lb-ft55 Nm
- Tie Rod End NutUse new cotter pin40 lb-ft54 Nm
- Tie Rod Nut40 lb-ft54 Nm
- Wheel Lug Nuts80 lb-ft108 Nm
Steering Angle Sensor4 specs
- Coupling Bolt25 lb-ft34 Nm
- Tie Rod End NutUse new cotter pin40 lb-ft54 Nm
- Tie Rod Nut40 lb-ft54 Nm
- Wheel Lug Nuts80 lb-ft108 Nm
Steering Column9 specs
- Coupling Bolt25 lb-ft34 Nm
- Ignition Switch BoltsVerify sequence with the service manual4 lb-ft5 Nm
- Pinch BoltVerify sequence with the service manual22 lb-ft30 Nm
- Power Steering Line FittingsUse new O-rings25 lb-ft34 Nm
- Steering Column BoltsVerify sequence with the service manual22 lb-ft30 Nm
- Steering Rack Bolts75 lb-ft102 Nm
- Tie Rod End NutUse new cotter pin40 lb-ft54 Nm
- Tie Rod Nut40 lb-ft54 Nm
- Wheel Lug Nuts80 lb-ft108 Nm
Steering Coupler5 specs
- Coupling Bolt25 lb-ft34 Nm
- Steering Rack BoltsVerify sequence with the service manual74 lb-ft100 Nm
- Tie Rod End NutUse new cotter pin40 lb-ft54 Nm
- Tie Rod Nut40 lb-ft54 Nm
- Wheel Lug Nuts80 lb-ft108 Nm
Steering Damper4 specs
- Coupling Bolt25 lb-ft34 Nm
- Tie Rod End NutUse new cotter pin40 lb-ft54 Nm
- Tie Rod Nut40 lb-ft54 Nm
- Wheel Lug Nuts80 lb-ft108 Nm
Steering Shaft - Intermediate5 specs
- Coupling Bolt25 lb-ft34 Nm
- Steering Rack BoltsVerify sequence with the service manual74 lb-ft100 Nm
- Tie Rod End NutUse new cotter pin40 lb-ft54 Nm
- Tie Rod Nut40 lb-ft54 Nm
- Wheel Lug Nuts80 lb-ft108 Nm
Steering Shaft - Upper4 specs
- Coupling Bolt25 lb-ft34 Nm
- Tie Rod End NutUse new cotter pin40 lb-ft54 Nm
- Tie Rod Nut40 lb-ft54 Nm
- Wheel Lug Nuts80 lb-ft108 Nm
Steering Wheel8 specs
- Airbag Module BoltsTorx - usually T30. Verify sequence with the service manual5 lb-ft7 Nm
- Coupling Bolt25 lb-ft34 Nm
- Power Steering Line FittingsUse new O-rings25 lb-ft34 Nm
- Steering Rack Bolts75 lb-ft102 Nm
- Steering Wheel NutVerify sequence with the service manual40 lb-ft54 Nm
- Tie Rod End NutUse new cotter pin40 lb-ft54 Nm
- Tie Rod Nut40 lb-ft54 Nm
- Wheel Lug Nuts80 lb-ft108 Nm
Tie Rod Assembly6 specs
- Coupling Bolt25 lb-ft34 Nm
- Tie Rod End Castle NutUse new cotter pin41 lb-ft55 Nm
- Tie Rod End NutNew cotter pin40 lb-ft54 Nm
- Tie Rod Lock NutAfter alignment50 lb-ft68 Nm
- Tie Rod Nut40 lb-ft54 Nm
- Wheel Lug Nuts80 lb-ft108 Nm
Tie Rod End - Inner7 specs
- Coupling Bolt25 lb-ft34 Nm
- Steering Rack Bolts74 lb-ft100 Nm
- Tie Rod End Castle NutUse new cotter pin41 lb-ft55 Nm
- Tie Rod End NutNew cotter pin40 lb-ft54 Nm
- Tie Rod Lock NutAfter alignment50 lb-ft68 Nm
- Tie Rod Nut40 lb-ft54 Nm
- Wheel Lug Nuts80 lb-ft108 Nm
Tie Rod End - Outer6 specs
- Coupling Bolt25 lb-ft34 Nm
- Tie Rod End Castle NutUse new cotter pin41 lb-ft55 Nm
- Tie Rod End NutUse new cotter pin40 lb-ft54 Nm
- Tie Rod Lock NutAfter alignment50 lb-ft68 Nm
- Tie Rod Nut40 lb-ft54 Nm
- Wheel Lug Nuts80 lb-ft108 Nm
Tie Rods - Both Sides6 specs
- Coupling Bolt25 lb-ft34 Nm
- Tie Rod End Castle NutUse new cotter pin41 lb-ft55 Nm
- Tie Rod End NutUse new cotter pin40 lb-ft54 Nm
- Tie Rod Lock NutAfter alignment50 lb-ft68 Nm
- Tie Rod Nut40 lb-ft54 Nm
- Wheel Lug Nuts80 lb-ft108 Nm

Drivetrain

Axle Seal - Front6 specs
- Axle NutUse new cotter pin or stake nut184 lb-ft250 Nm
- CV Bolts45 lb-ft61 Nm
- CV Joint Bolts45 lb-ft61 Nm
- Differential Cover Bolts26 lb-ft35 Nm
- Driveshaft Bolts55 lb-ft75 Nm
- Wheel Lug NutsTorque in star pattern80 lb-ft108 Nm
CV Axle - Front9 specs
- Axle NutUse new nut, stake after180 lb-ft244 Nm
- Ball Joint Pinch Bolt41 lb-ft55 Nm
- CV Axle NutUse new cotter pin or stake nut184 lb-ft250 Nm
- CV Bolts45 lb-ft61 Nm
- CV Joint Bolts45 lb-ft61 Nm
- Differential Cover BoltsApply RTV sealant25 lb-ft34 Nm
- Driveshaft Bolts55 lb-ft75 Nm
- Lower Ball Joint Nut75 lb-ft102 Nm
- Wheel Lug Nuts80 lb-ft108 Nm
CV Axles - Front Pair6 specs
- Axle NutUse new cotter pin or stake nut184 lb-ft250 Nm
- CV Bolts45 lb-ft61 Nm
- CV Joint Bolts45 lb-ft61 Nm
- Driveshaft Bolts55 lb-ft75 Nm
- Lower Ball Joint Nut75 lb-ft102 Nm
- Wheel Lug NutsTorque in star pattern80 lb-ft108 Nm
CV Boot - Inner5 specs
- Axle NutUse new cotter pin or stake nut184 lb-ft250 Nm
- CV Bolts45 lb-ft61 Nm
- CV Joint Bolts45 lb-ft61 Nm
- Driveshaft Bolts55 lb-ft75 Nm
- Wheel Lug NutsTorque in star pattern80 lb-ft108 Nm
CV Boot - Outer5 specs
- Axle NutUse new cotter pin or stake nut184 lb-ft250 Nm
- CV Bolts45 lb-ft61 Nm
- CV Joint Bolts45 lb-ft61 Nm
- Driveshaft Bolts55 lb-ft75 Nm
- Wheel Lug NutsTorque in star pattern80 lb-ft108 Nm
Differential Cover Gasket4 specs
- CV Bolts45 lb-ft61 Nm
- CV Joint Bolts45 lb-ft61 Nm
- Differential Cover BoltsApply RTV sealant25 lb-ft34 Nm
- Driveshaft Bolts55 lb-ft75 Nm
Differential Pinion Seal4 specs
- CV Bolts45 lb-ft61 Nm
- CV Joint Bolts45 lb-ft61 Nm
- Differential Cover BoltsApply RTV sealant25 lb-ft34 Nm
- Driveshaft Bolts55 lb-ft75 Nm
Differential Rebuild - Rear8 specs
- Axle Nut180 lb-ft244 Nm
- CV Bolts45 lb-ft61 Nm
- CV Joint Bolts45 lb-ft61 Nm
- Differential Cover BoltsApply RTV sealant25 lb-ft34 Nm
- Drain PlugNew washer30 lb-ft41 Nm
- Driveshaft Bolts55 lb-ft75 Nm
- Fill Plug30 lb-ft41 Nm
- Wheel Lug Nuts80 lb-ft108 Nm
Limited Slip Clutch Pack7 specs
- Axle NutUse new cotter pin or stake nut184 lb-ft250 Nm
- CV Bolts45 lb-ft61 Nm
- CV Joint Bolts45 lb-ft61 Nm
- Differential Cover Bolts26 lb-ft35 Nm
- Driveshaft Bolts55 lb-ft75 Nm
- Driveshaft U-Joint StrapsTighten evenly15 lb-ft20 Nm
- Wheel Lug NutsTorque in star pattern80 lb-ft108 Nm
Ring and Pinion7 specs
- Axle NutUse new cotter pin or stake nut184 lb-ft250 Nm
- CV Bolts45 lb-ft61 Nm
- CV Joint Bolts45 lb-ft61 Nm
- Differential Cover Bolts26 lb-ft35 Nm
- Driveshaft Bolts55 lb-ft75 Nm
- Driveshaft U-Joint StrapsTighten evenly15 lb-ft20 Nm
- Wheel Lug NutsTorque in star pattern80 lb-ft108 Nm
U-Joint6 specs
- Axle NutUse new nut, stake after180 lb-ft244 Nm
- CV Bolts45 lb-ft61 Nm
- CV Joint Bolts45 lb-ft61 Nm
- Differential Cover BoltsApply RTV sealant25 lb-ft34 Nm
- Driveshaft Bolts55 lb-ft75 Nm
- Wheel Lug Nuts80 lb-ft108 Nm
Wheel Bearing - Press-In Front6 specs
- ABS Sensor Bolt8 lb-ft11 Nm
- Axle NutUse new cotter pin or stake nut184 lb-ft250 Nm
- CV Joint Bolts45 lb-ft61 Nm
- Driveshaft Bolts55 lb-ft75 Nm
- Hub Bolts75 lb-ft102 Nm
- Wheel Lug NutsTorque in star pattern80 lb-ft108 Nm
Wheel Bearing - Press-In Rear7 specs
- ABS Sensor Bolt8 lb-ft11 Nm
- Axle NutUse new cotter pin or stake nut184 lb-ft250 Nm
- CV Joint Bolts45 lb-ft61 Nm
- Differential Cover Bolts26 lb-ft35 Nm
- Driveshaft Bolts55 lb-ft75 Nm
- Hub Bolts75 lb-ft102 Nm
- Wheel Lug NutsTorque in star pattern80 lb-ft108 Nm
Wheel Bearing Hub - Front4 specs
- ABS Sensor BoltDo not overtighten7 lb-ft10 Nm
- Axle NutUse new cotter pin after torque184 lb-ft250 Nm
- Caliper Bracket Bolts88 lb-ft120 Nm
- Wheel Bearing Hub BoltsApply threadlocker if specified81 lb-ft110 Nm
Wheel Bearing Hub - Rear3 specs
- Axle NutUse new cotter pin after torque148 lb-ft200 Nm
- Caliper Bracket Bolts81 lb-ft110 Nm
- Wheel Bearing Hub BoltsApply threadlocker if specified74 lb-ft100 Nm
Wheel Studs5 specs
- Axle NutUse new cotter pin or stake nut184 lb-ft250 Nm
- CV Bolts45 lb-ft61 Nm
- CV Joint Bolts45 lb-ft61 Nm
- Driveshaft Bolts55 lb-ft75 Nm
- Wheel Lug NutsTorque in star pattern80 lb-ft108 Nm

Transmission

Clutch Hydraulic Line4 specs
- Bell Housing Bolts35 lb-ft47 Nm
- Drain PlugUse new washer25 lb-ft34 Nm
- Fill Plug25 lb-ft34 Nm
- Pressure Plate BoltStar pattern20 lb-ft27 Nm
Dual Mass Flywheel4 specs
- Drain PlugUse new washer25 lb-ft34 Nm
- Fill Plug25 lb-ft34 Nm
- Flywheel BoltsOften TTY, tighten in star pattern70 lb-ft95 Nm
- Transmission Drain PlugUse new crush washer if equipped22 lb-ft30 Nm
Manual Trans Fluid Change3 specs
- Drain PlugUse new washer25 lb-ft34 Nm
- Fill Plug25 lb-ft34 Nm
- Transmission Drain PlugUse new crush washer if equipped22 lb-ft30 Nm
Neutral Safety Switch3 specs
- Drain PlugUse new washer25 lb-ft34 Nm
- Fill Plug25 lb-ft34 Nm
- Switch Mounting Bolts11 lb-ft15 Nm
Overdrive Solenoid4 specs
- Drain PlugUse new washer25 lb-ft34 Nm
- Fill Plug25 lb-ft34 Nm
- Transmission Drain PlugUse new crush washer if equipped22 lb-ft30 Nm
- Transmission Pan BoltsTighten in criss-cross pattern9 lb-ft12 Nm
Pressure Plate4 specs
- Drain PlugUse new washer25 lb-ft34 Nm
- Fill Plug25 lb-ft34 Nm
- Flywheel BoltsOften TTY, tighten in star pattern70 lb-ft95 Nm
- Transmission Drain PlugUse new crush washer if equipped22 lb-ft30 Nm
Shift Cable4 specs
- Adjustment Nut7 lb-ft10 Nm
- Cable Bracket Bolts11 lb-ft15 Nm
- Drain PlugUse new washer25 lb-ft34 Nm
- Fill Plug25 lb-ft34 Nm
Shift Fork3 specs
- Drain PlugUse new washer25 lb-ft34 Nm
- Fill Plug25 lb-ft34 Nm
- Transmission Drain PlugUse new crush washer if equipped22 lb-ft30 Nm
Shift Linkage4 specs
- Drain PlugUse new washer25 lb-ft34 Nm
- Fill Plug25 lb-ft34 Nm
- Linkage Bolts11 lb-ft15 Nm
- Pivot Bolts9 lb-ft12 Nm
Shift Solenoid - Single4 specs
- Drain PlugUse new washer25 lb-ft34 Nm
- Fill Plug25 lb-ft34 Nm
- Transmission Drain PlugUse new crush washer if equipped22 lb-ft30 Nm
- Transmission Pan BoltsTighten in criss-cross pattern9 lb-ft12 Nm
Shift Solenoids - All4 specs
- Drain PlugUse new washer25 lb-ft34 Nm
- Fill Plug25 lb-ft34 Nm
- Transmission Drain PlugUse new crush washer if equipped22 lb-ft30 Nm
- Transmission Pan BoltsTighten in criss-cross pattern9 lb-ft12 Nm
Synchros - All4 specs
- Drain PlugUse new washer25 lb-ft34 Nm
- Fill Plug25 lb-ft34 Nm
- Transmission Drain PlugUse new crush washer if equipped22 lb-ft30 Nm
- Transmission Pan BoltsTighten in criss-cross pattern9 lb-ft12 Nm
Synchros - Single Gear3 specs
- Drain PlugUse new washer25 lb-ft34 Nm
- Fill Plug25 lb-ft34 Nm
- Transmission Drain PlugUse new crush washer if equipped22 lb-ft30 Nm
Torque Converter4 specs
- Drain PlugUse new washer25 lb-ft34 Nm
- Fill Plug25 lb-ft34 Nm
- Flexplate BoltsAutomatic transmissions63 lb-ft85 Nm
- Torque Converter BoltsTighten evenly37 lb-ft50 Nm
Torque Converter Clutch Solenoid4 specs
- Drain PlugUse new washer25 lb-ft34 Nm
- Fill Plug25 lb-ft34 Nm
- Transmission Drain PlugUse new crush washer if equipped22 lb-ft30 Nm
- Transmission Pan BoltsTighten in criss-cross pattern9 lb-ft12 Nm
Transmission Control Module4 specs
- Drain PlugUse new washer25 lb-ft34 Nm
- Fill Plug25 lb-ft34 Nm
- Transmission Drain PlugUse new crush washer if equipped22 lb-ft30 Nm
- Transmission Pan BoltsTighten in criss-cross pattern9 lb-ft12 Nm
Transmission Cooler Lines2 specs
- Drain PlugUse new washer25 lb-ft34 Nm
- Fill Plug25 lb-ft34 Nm
Transmission Filter4 specs
- Drain PlugUse new washer25 lb-ft34 Nm
- Fill Plug25 lb-ft34 Nm
- Transmission Drain PlugUse new crush washer if equipped22 lb-ft30 Nm
- Transmission Pan BoltsTighten in criss-cross pattern9 lb-ft12 Nm
Transmission Filter and Fluid4 specs
- Drain PlugUse new washer25 lb-ft34 Nm
- Fill Plug25 lb-ft34 Nm
- Transmission Drain PlugUse new crush washer if equipped22 lb-ft30 Nm
- Transmission Pan BoltsTighten in criss-cross pattern9 lb-ft12 Nm
Transmission Fluid Change5 specs
- Drain PlugUse new washer25 lb-ft34 Nm
- Fill Plug25 lb-ft34 Nm
- Transmission Drain PlugUse new crush washer if equipped22 lb-ft30 Nm
- Transmission Filter BoltsIf equipped with bolted filter6 lb-ft8 Nm
- Transmission Pan BoltsTighten in criss-cross pattern9 lb-ft12 Nm
Transmission Flush4 specs
- Drain PlugUse new washer25 lb-ft34 Nm
- Fill Plug25 lb-ft34 Nm
- Transmission Drain PlugUse new crush washer if equipped22 lb-ft30 Nm
- Transmission Pan BoltsTighten in criss-cross pattern9 lb-ft12 Nm
Transmission Input Shaft Bearing5 specs
- Drain PlugUse new washer25 lb-ft34 Nm
- Fill Plug25 lb-ft34 Nm
- Flywheel BoltsOften TTY, tighten in star pattern70 lb-ft95 Nm
- Transmission Drain PlugUse new crush washer if equipped22 lb-ft30 Nm
- Transmission Pan BoltsTighten in criss-cross pattern9 lb-ft12 Nm
Transmission Oil Cooler9 specs
- Coolant Drain Plug11 lb-ft15 Nm
- Drain PetcockHand tight5 lb-ft7 Nm
- Drain PlugUse new washer25 lb-ft34 Nm
- Fan Bolts8 lb-ft11 Nm
- Fill Plug25 lb-ft34 Nm
- Hose Clamps2 lb-ft3 Nm
- Pump Bolts18 lb-ft24 Nm
- Thermostat Housing Bolt11 lb-ft15 Nm
- Water Pump BoltsTighten in criss-cross pattern18 lb-ft25 Nm
Transmission Output Shaft Bearing5 specs
- Drain PlugUse new washer25 lb-ft34 Nm
- Fill Plug25 lb-ft34 Nm
- Flywheel BoltsOften TTY, tighten in star pattern70 lb-ft95 Nm
- Transmission Drain PlugUse new crush washer if equipped22 lb-ft30 Nm
- Transmission Pan BoltsTighten in criss-cross pattern9 lb-ft12 Nm
Transmission Pan Gasket4 specs
- Drain PlugUse new washer25 lb-ft34 Nm
- Fill Plug25 lb-ft34 Nm
- Transmission Drain PlugUse new crush washer if equipped22 lb-ft30 Nm
- Transmission Pan BoltsTighten in criss-cross pattern9 lb-ft12 Nm
Transmission R&R - Automatic5 specs
- Drain PlugUse new washer25 lb-ft34 Nm
- Fill Plug25 lb-ft34 Nm
- Flywheel BoltsOften TTY, tighten in star pattern70 lb-ft95 Nm
- Transmission Drain PlugUse new crush washer if equipped22 lb-ft30 Nm
- Transmission Pan BoltsTighten in criss-cross pattern9 lb-ft12 Nm
Transmission R&R - Manual4 specs
- Drain PlugUse new washer25 lb-ft34 Nm
- Fill Plug25 lb-ft34 Nm
- Flywheel BoltsOften TTY, tighten in star pattern70 lb-ft95 Nm
- Transmission Drain PlugUse new crush washer if equipped22 lb-ft30 Nm
Transmission Range Sensor4 specs
- Drain PlugUse new washer25 lb-ft34 Nm
- Fill Plug25 lb-ft34 Nm
- Transmission Drain PlugUse new crush washer if equipped22 lb-ft30 Nm
- Transmission Pan BoltsTighten in criss-cross pattern9 lb-ft12 Nm
Transmission Rebuild - Automatic5 specs
- Drain PlugUse new washer25 lb-ft34 Nm
- Fill Plug25 lb-ft34 Nm
- Flywheel BoltsOften TTY, tighten in star pattern70 lb-ft95 Nm
- Transmission Drain PlugUse new crush washer if equipped22 lb-ft30 Nm
- Transmission Pan BoltsTighten in criss-cross pattern9 lb-ft12 Nm
Transmission Rebuild - Manual5 specs
- Drain PlugUse new washer25 lb-ft34 Nm
- Fill Plug25 lb-ft34 Nm
- Flywheel BoltsOften TTY, tighten in star pattern70 lb-ft95 Nm
- Transmission Drain PlugUse new crush washer if equipped22 lb-ft30 Nm
- Transmission Pan BoltsTighten in criss-cross pattern9 lb-ft12 Nm
Transmission Speed Sensor - Input3 specs
- Drain PlugUse new washer25 lb-ft34 Nm
- Fill Plug25 lb-ft34 Nm
- Transmission Pan BoltsTighten in criss-cross pattern9 lb-ft12 Nm
Transmission Speed Sensor - Output2 specs
- Drain PlugUse new washer25 lb-ft34 Nm
- Fill Plug25 lb-ft34 Nm
Valve Body4 specs
- Drain PlugUse new washer25 lb-ft34 Nm
- Fill Plug25 lb-ft34 Nm
- Transmission Drain PlugUse new crush washer if equipped22 lb-ft30 Nm
- Transmission Pan BoltsTighten in criss-cross pattern9 lb-ft12 Nm

Exhaust

Catalytic Converter - Direct Fit5 specs
- Exhaust Flange BoltApply anti-seize33 lb-ft45 Nm
- Hanger Bolts15 lb-ft20 Nm
- Heat Shield Bolts7 lb-ft10 Nm
- Manifold NutsApply anti-seize25 lb-ft34 Nm
- O2 SensorApply anti-seize to threads only33 lb-ft45 Nm
Catalytic Converter - Universal5 specs
- Exhaust Flange BoltApply anti-seize33 lb-ft45 Nm
- Hanger Bolts15 lb-ft20 Nm
- Heat Shield Bolts7 lb-ft10 Nm
- Manifold NutsApply anti-seize25 lb-ft34 Nm
- O2 SensorApply anti-seize to threads only33 lb-ft45 Nm
Downpipe5 specs
- Exhaust Flange BoltApply anti-seize33 lb-ft45 Nm
- Hanger Bolts15 lb-ft20 Nm
- Heat Shield Bolts7 lb-ft10 Nm
- Manifold NutsApply anti-seize25 lb-ft34 Nm
- O2 SensorApply anti-seize to threads only33 lb-ft45 Nm
EGR Tube4 specs
- Exhaust Flange BoltApply anti-seize33 lb-ft45 Nm
- Hanger Bolts15 lb-ft20 Nm
- Heat Shield Bolts7 lb-ft10 Nm
- Manifold NutsApply anti-seize25 lb-ft34 Nm
EGR Valve6 specs
- EGR Tube Fitting26 lb-ft35 Nm
- EGR Valve Bolts18 lb-ft25 Nm
- Hanger Bolts15 lb-ft20 Nm
- Heat Shield Bolts10 lb-ft14 Nm
- Manifold NutsApply anti-seize25 lb-ft34 Nm
- O2 SensorApply anti-seize to threads35 lb-ft47 Nm
Exhaust Clamp4 specs
- Exhaust Flange BoltApply anti-seize33 lb-ft45 Nm
- Hanger Bolts15 lb-ft20 Nm
- Heat Shield Bolts7 lb-ft10 Nm
- Manifold NutsApply anti-seize25 lb-ft34 Nm
Exhaust Gasket - Front5 specs
- Exhaust Flange BoltApply anti-seize33 lb-ft45 Nm
- Hanger Bolts15 lb-ft20 Nm
- Heat Shield Bolts7 lb-ft10 Nm
- Manifold NutsApply anti-seize25 lb-ft34 Nm
- O2 SensorApply anti-seize to threads only33 lb-ft45 Nm
Exhaust Gasket - Rear4 specs
- Exhaust Flange BoltApply anti-seize33 lb-ft45 Nm
- Hanger Bolts15 lb-ft20 Nm
- Heat Shield Bolts7 lb-ft10 Nm
- Manifold NutsApply anti-seize25 lb-ft34 Nm
Exhaust Hangers4 specs
- Exhaust Flange BoltApply anti-seize33 lb-ft45 Nm
- Hanger Bolts15 lb-ft20 Nm
- Heat Shield Bolts7 lb-ft10 Nm
- Manifold NutsApply anti-seize25 lb-ft34 Nm
Exhaust Manifold Studs5 specs
- Exhaust Flange BoltApply anti-seize33 lb-ft45 Nm
- Hanger Bolts15 lb-ft20 Nm
- Heat Shield Bolts7 lb-ft10 Nm
- Manifold NutsApply anti-seize25 lb-ft34 Nm
- O2 SensorApply anti-seize to threads only33 lb-ft45 Nm
Exhaust Pipe - Rear Section4 specs
- Exhaust Flange BoltApply anti-seize33 lb-ft45 Nm
- Hanger Bolts15 lb-ft20 Nm
- Heat Shield Bolts7 lb-ft10 Nm
- Manifold NutsApply anti-seize25 lb-ft34 Nm
Exhaust Tip3 specs
- Exhaust Flange BoltApply anti-seize33 lb-ft45 Nm
- Hanger Bolts15 lb-ft20 Nm
- Manifold NutsApply anti-seize25 lb-ft34 Nm
Flex Pipe5 specs
- Exhaust Clamps41 lb-ft55 Nm
- Hanger Bolts15 lb-ft20 Nm
- Heat Shield Bolts10 lb-ft14 Nm
- Manifold NutsApply anti-seize25 lb-ft34 Nm
- O2 SensorApply anti-seize to threads35 lb-ft47 Nm
Front Pipe5 specs
- Exhaust Flange BoltApply anti-seize33 lb-ft45 Nm
- Hanger Bolts15 lb-ft20 Nm
- Heat Shield Bolts7 lb-ft10 Nm
- Manifold NutsApply anti-seize25 lb-ft34 Nm
- O2 SensorApply anti-seize to threads only33 lb-ft45 Nm
Intermediate Pipe5 specs
- Exhaust Flange BoltApply anti-seize33 lb-ft45 Nm
- Hanger Bolts15 lb-ft20 Nm
- Heat Shield Bolts7 lb-ft10 Nm
- Manifold NutsApply anti-seize25 lb-ft34 Nm
- O2 SensorApply anti-seize to threads only33 lb-ft45 Nm
Muffler2 specs
- Hanger Bracket Bolts18 lb-ft25 Nm
- Muffler Clamps41 lb-ft55 Nm
O2 Sensor - Downstream5 specs
- Exhaust Flange BoltApply anti-seize33 lb-ft45 Nm
- Hanger Bolts15 lb-ft20 Nm
- Heat Shield Bolts7 lb-ft10 Nm
- Manifold NutsApply anti-seize25 lb-ft34 Nm
- O2 SensorApply anti-seize to threads only33 lb-ft45 Nm
O2 Sensor - Upstream5 specs
- Exhaust Flange BoltApply anti-seize33 lb-ft45 Nm
- Hanger Bolts15 lb-ft20 Nm
- Heat Shield Bolts7 lb-ft10 Nm
- Manifold NutsApply anti-seize25 lb-ft34 Nm
- O2 SensorApply anti-seize to threads only33 lb-ft45 Nm
O2 Sensors - All5 specs
- Exhaust Flange BoltApply anti-seize33 lb-ft45 Nm
- Hanger Bolts15 lb-ft20 Nm
- Heat Shield Bolts7 lb-ft10 Nm
- Manifold NutsApply anti-seize25 lb-ft34 Nm
- O2 SensorApply anti-seize to threads only33 lb-ft45 Nm
Resonator5 specs
- Exhaust Clamps41 lb-ft55 Nm
- Hanger Bolts15 lb-ft20 Nm
- Heat Shield Bolts10 lb-ft14 Nm
- Manifold NutsApply anti-seize25 lb-ft34 Nm
- O2 SensorApply anti-seize to threads35 lb-ft47 Nm
Tail Pipe4 specs
- Exhaust Flange BoltApply anti-seize33 lb-ft45 Nm
- Hanger Bolts15 lb-ft20 Nm
- Heat Shield Bolts7 lb-ft10 Nm
- Manifold NutsApply anti-seize25 lb-ft34 Nm

Heating and A/C

AC Accumulator5 specs
- AC Line FittingsUse new O-rings, add PAG oil15 lb-ft20 Nm
- Blower Motor Mounting Screw3 lb-ft4 Nm
- Compressor Bolts25 lb-ft34 Nm
- Duct Clips2 lb-ft3 Nm
- Mounting Bracket Bolts18 lb-ft24 Nm
AC Clutch Coil4 specs
- Blower Motor Mounting Screw3 lb-ft4 Nm
- Compressor Bolts25 lb-ft34 Nm
- Duct Clips2 lb-ft3 Nm
- Mounting Bracket Bolts18 lb-ft24 Nm
AC Compressor3 specs
- AC Compressor Bolts18 lb-ft25 Nm
- AC Line FittingsUse new O-rings, add PAG oil15 lb-ft20 Nm
- Clutch Connector Bolt6 lb-ft8 Nm
AC Compressor Clutch4 specs
- Blower Motor Mounting Screw3 lb-ft4 Nm
- Compressor Bolts25 lb-ft34 Nm
- Duct Clips2 lb-ft3 Nm
- Mounting Bracket Bolts18 lb-ft24 Nm
AC Compressor Oil Add5 specs
- AC Line FittingsUse new O-rings, add PAG oil15 lb-ft20 Nm
- Blower Motor Mounting Screw3 lb-ft4 Nm
- Compressor Bolts25 lb-ft34 Nm
- Duct Clips2 lb-ft3 Nm
- Mounting Bracket Bolts18 lb-ft24 Nm
AC Condenser2 specs
- AC Line FittingsUse new O-rings15 lb-ft20 Nm
- Condenser Mounting Bolts9 lb-ft12 Nm
AC Evaporator7 specs
- AC Line FittingsUse new O-rings, add PAG oil15 lb-ft20 Nm
- Blower Motor Mounting Screw5 lb-ft7 Nm
- Compressor Bolts25 lb-ft34 Nm
- Duct Clips2 lb-ft3 Nm
- Evaporator Case Screws4 lb-ft5 Nm
- Expansion Valve7 lb-ft10 Nm
- Mounting Bracket Bolts18 lb-ft24 Nm
AC Expansion Valve (TXV)6 specs
- AC Line FittingsUse new O-rings, add PAG oil15 lb-ft20 Nm
- Blower Motor Mounting Screw5 lb-ft7 Nm
- Compressor Bolts25 lb-ft34 Nm
- Duct Clips2 lb-ft3 Nm
- Expansion Valve7 lb-ft10 Nm
- Mounting Bracket Bolts18 lb-ft24 Nm
AC High Pressure Switch5 specs
- AC Line FittingsUse new O-rings, add PAG oil15 lb-ft20 Nm
- Blower Motor Mounting Screw3 lb-ft4 Nm
- Compressor Bolts25 lb-ft34 Nm
- Duct Clips2 lb-ft3 Nm
- Mounting Bracket Bolts18 lb-ft24 Nm
AC Hose - High Side5 specs
- AC Line FittingsUse new O-rings, add PAG oil15 lb-ft20 Nm
- Blower Motor Mounting Screw3 lb-ft4 Nm
- Compressor Bolts25 lb-ft34 Nm
- Duct Clips2 lb-ft3 Nm
- Mounting Bracket Bolts18 lb-ft24 Nm
AC Hose - Low Side6 specs
- AC Line FittingsUse new O-rings, add PAG oil15 lb-ft20 Nm
- Blower Motor Mounting Screw3 lb-ft4 Nm
- Compressor Bolts25 lb-ft34 Nm
- Duct Clips2 lb-ft3 Nm
- Hose Clamps2 lb-ft3 Nm
- Mounting Bracket Bolts18 lb-ft24 Nm
AC Hose Assembly6 specs
- AC Line FittingsUse new O-rings, add PAG oil15 lb-ft20 Nm
- Blower Motor Mounting Screw3 lb-ft4 Nm
- Compressor Bolts25 lb-ft34 Nm
- Duct Clips2 lb-ft3 Nm
- Hose Clamps2 lb-ft3 Nm
- Mounting Bracket Bolts18 lb-ft24 Nm
AC Low Pressure Switch5 specs
- AC Line FittingsUse new O-rings, add PAG oil15 lb-ft20 Nm
- Blower Motor Mounting Screw3 lb-ft4 Nm
- Compressor Bolts25 lb-ft34 Nm
- Duct Clips2 lb-ft3 Nm
- Mounting Bracket Bolts18 lb-ft24 Nm
AC Orifice Tube5 specs
- AC Line FittingsUse new O-rings, add PAG oil15 lb-ft20 Nm
- Blower Motor Mounting Screw3 lb-ft4 Nm
- Compressor Bolts25 lb-ft34 Nm
- Duct Clips2 lb-ft3 Nm
- Mounting Bracket Bolts18 lb-ft24 Nm
AC Pressure Sensor5 specs
- AC Line FittingsUse new O-rings, add PAG oil15 lb-ft20 Nm
- Blower Motor Mounting Screw3 lb-ft4 Nm
- Compressor Bolts25 lb-ft34 Nm
- Duct Clips2 lb-ft3 Nm
- Mounting Bracket Bolts18 lb-ft24 Nm
AC Receiver/Drier6 specs
- AC Line FittingsUse new O-rings, add PAG oil15 lb-ft20 Nm
- Blower Motor Mounting Screw5 lb-ft7 Nm
- Compressor Bolts25 lb-ft34 Nm
- Duct Clips2 lb-ft3 Nm
- Mounting Bracket Bolts18 lb-ft24 Nm
- Receiver Drier Bolts7 lb-ft10 Nm
AC Recharge4 specs
- Blower Motor Mounting Screw3 lb-ft4 Nm
- Compressor Bolts25 lb-ft34 Nm
- Duct Clips2 lb-ft3 Nm
- Mounting Bracket Bolts18 lb-ft24 Nm
Blend Door Actuator5 specs
- Actuator Screws2 lb-ft3 Nm
- Blower Motor Mounting Screw5 lb-ft7 Nm
- Compressor Bolts25 lb-ft34 Nm
- Duct Clips2 lb-ft3 Nm
- Mounting Bracket Bolts18 lb-ft24 Nm
Cabin Air Filter4 specs
- Compressor Bolts25 lb-ft34 Nm
- Connector Bolts5 lb-ft7 Nm
- Filter Cover ClipsTool-free on most2 lb-ft3 Nm
- Glove Box Screws3 lb-ft4 Nm
Climate Control Module4 specs
- Blower Motor Mounting Screw3 lb-ft4 Nm
- Compressor Bolts25 lb-ft34 Nm
- Duct Clips2 lb-ft3 Nm
- Mounting Bracket Bolts18 lb-ft24 Nm
HVAC Control Panel4 specs
- Blower Motor Mounting Screw3 lb-ft4 Nm
- Compressor Bolts25 lb-ft34 Nm
- Duct Clips2 lb-ft3 Nm
- Mounting Bracket Bolts18 lb-ft24 Nm
Mode Door Actuator4 specs
- Blower Motor Mounting Screw3 lb-ft4 Nm
- Compressor Bolts25 lb-ft34 Nm
- Duct Clips2 lb-ft3 Nm
- Mounting Bracket Bolts18 lb-ft24 Nm
Recirculation Door Actuator4 specs
- Blower Motor Mounting Screw3 lb-ft4 Nm
- Compressor Bolts25 lb-ft34 Nm
- Duct Clips2 lb-ft3 Nm
- Mounting Bracket Bolts18 lb-ft24 Nm

Body

Bumper Cover - Front8 specs
- Bumper Cover Bolts7 lb-ft10 Nm
- Fender Liner Screws2 lb-ft3 Nm
- Grille Clips4 lb-ft5 Nm
- Hinge Bolts20 lb-ft27 Nm
- Latch Bolts10 lb-ft14 Nm
- Panel Bolts10 lb-ft14 Nm
- Striker Bolts25 lb-ft34 Nm
- Trim ClipsReplace if broken2 lb-ft3 Nm
Bumper Cover - Rear7 specs
- Bumper Cover Bolts7 lb-ft10 Nm
- Hinge Bolts20 lb-ft27 Nm
- Latch Bolts10 lb-ft14 Nm
- Panel Bolts10 lb-ft14 Nm
- Striker Bolts25 lb-ft34 Nm
- Trim ClipsReplace if broken2 lb-ft3 Nm
- Trunk Liner Screws2 lb-ft3 Nm
Bumper Reinforcement - Front7 specs
- Body Panel Bolts18 lb-ft25 Nm
- Bumper Cover Bolts7 lb-ft10 Nm
- Hinge Bolts20 lb-ft27 Nm
- Latch Bolts10 lb-ft14 Nm
- Panel Bolts10 lb-ft14 Nm
- Striker Bolts25 lb-ft34 Nm
- Trim ClipsReplace if broken2 lb-ft3 Nm
Bumper Reinforcement - Rear7 specs
- Body Panel Bolts18 lb-ft25 Nm
- Bumper Cover Bolts7 lb-ft10 Nm
- Hinge Bolts20 lb-ft27 Nm
- Latch Bolts10 lb-ft14 Nm
- Panel Bolts10 lb-ft14 Nm
- Striker Bolts25 lb-ft34 Nm
- Trim ClipsReplace if broken2 lb-ft3 Nm
Door Check/Stop6 specs
- Body Panel Bolts18 lb-ft25 Nm
- Hinge Bolts20 lb-ft27 Nm
- Latch Bolts10 lb-ft14 Nm
- Panel Bolts10 lb-ft14 Nm
- Striker Bolts25 lb-ft34 Nm
- Trim ClipsReplace if broken2 lb-ft3 Nm
Door Glass5 specs
- Hinge Bolts20 lb-ft27 Nm
- Latch Bolts10 lb-ft14 Nm
- Panel Bolts10 lb-ft14 Nm
- Striker Bolts25 lb-ft34 Nm
- Trim ClipsReplace if broken2 lb-ft3 Nm
Door Handle - Exterior7 specs
- Handle Mounting Bolts6 lb-ft8 Nm
- Hinge Bolts20 lb-ft27 Nm
- Latch Bolts10 lb-ft14 Nm
- Lock Rod Clips4 lb-ft5 Nm
- Panel Bolts10 lb-ft14 Nm
- Striker Bolts25 lb-ft34 Nm
- Trim ClipsReplace if broken2 lb-ft3 Nm
Door Handle - Interior7 specs
- Cable Clips4 lb-ft5 Nm
- Handle Screws2 lb-ft3 Nm
- Hinge Bolts20 lb-ft27 Nm
- Latch Bolts10 lb-ft14 Nm
- Panel Bolts10 lb-ft14 Nm
- Striker Bolts25 lb-ft34 Nm
- Trim ClipsReplace if broken2 lb-ft3 Nm
Door Hinge6 specs
- Door Hinge Bolts22 lb-ft30 Nm
- Hinge Bolts20 lb-ft27 Nm
- Latch Bolts10 lb-ft14 Nm
- Panel Bolts10 lb-ft14 Nm
- Striker Bolts25 lb-ft34 Nm
- Trim ClipsReplace if broken2 lb-ft3 Nm
Door Shell7 specs
- Body Panel Bolts18 lb-ft25 Nm
- Door Hinge Bolts22 lb-ft30 Nm
- Hinge Bolts20 lb-ft27 Nm
- Latch Bolts10 lb-ft14 Nm
- Panel Bolts10 lb-ft14 Nm
- Striker Bolts25 lb-ft34 Nm
- Trim ClipsReplace if broken2 lb-ft3 Nm
Door Skin7 specs
- Body Panel Bolts18 lb-ft25 Nm
- Door Hinge Bolts22 lb-ft30 Nm
- Hinge Bolts20 lb-ft27 Nm
- Latch Bolts10 lb-ft14 Nm
- Panel Bolts10 lb-ft14 Nm
- Striker Bolts25 lb-ft34 Nm
- Trim ClipsReplace if broken2 lb-ft3 Nm
Door Weatherstrip5 specs
- Hinge Bolts20 lb-ft27 Nm
- Latch Bolts10 lb-ft14 Nm
- Panel Bolts10 lb-ft14 Nm
- Striker Bolts25 lb-ft34 Nm
- Trim ClipsReplace if broken2 lb-ft3 Nm
Fender8 specs
- Fender Bolts9 lb-ft12 Nm
- Fender Liner Screws2 lb-ft3 Nm
- Hinge Bolts20 lb-ft27 Nm
- Hood Hinge Bolts18 lb-ft25 Nm
- Latch Bolts10 lb-ft14 Nm
- Panel Bolts10 lb-ft14 Nm
- Striker Bolts25 lb-ft34 Nm
- Trim ClipsReplace if broken2 lb-ft3 Nm
Fender Liner7 specs
- Body Panel Bolts18 lb-ft25 Nm
- Bumper Cover Bolts7 lb-ft10 Nm
- Hinge Bolts20 lb-ft27 Nm
- Latch Bolts10 lb-ft14 Nm
- Panel Bolts10 lb-ft14 Nm
- Striker Bolts25 lb-ft34 Nm
- Trim ClipsReplace if broken2 lb-ft3 Nm
Grille7 specs
- Clips4 lb-ft5 Nm
- Grille Mounting Screws2 lb-ft3 Nm
- Hinge Bolts20 lb-ft27 Nm
- Latch Bolts10 lb-ft14 Nm
- Panel Bolts10 lb-ft14 Nm
- Striker Bolts25 lb-ft34 Nm
- Trim ClipsReplace if broken2 lb-ft3 Nm
Hood8 specs
- Hinge Bolts20 lb-ft27 Nm
- Hood Hinge Bolts18 lb-ft25 Nm
- Hood Latch Bolts9 lb-ft12 Nm
- Hood Strut Bolts7 lb-ft10 Nm
- Latch Bolts10 lb-ft14 Nm
- Panel Bolts10 lb-ft14 Nm
- Striker Bolts25 lb-ft34 Nm
- Trim ClipsReplace if broken2 lb-ft3 Nm
Hood Hinge6 specs
- Body Panel Bolts18 lb-ft25 Nm
- Hinge Bolts20 lb-ft27 Nm
- Latch Bolts10 lb-ft14 Nm
- Panel Bolts10 lb-ft14 Nm
- Striker Bolts25 lb-ft34 Nm
- Trim ClipsReplace if broken2 lb-ft3 Nm
Hood Latch7 specs
- Cable Clips4 lb-ft5 Nm
- Hinge Bolts20 lb-ft27 Nm
- Hood Latch Bolts9 lb-ft12 Nm
- Latch Bolts10 lb-ft14 Nm
- Panel Bolts10 lb-ft14 Nm
- Striker Bolts25 lb-ft34 Nm
- Trim ClipsReplace if broken2 lb-ft3 Nm
Hood Release Cable7 specs
- Body Panel Bolts18 lb-ft25 Nm
- Bumper Cover Bolts7 lb-ft10 Nm
- Hinge Bolts20 lb-ft27 Nm
- Latch Bolts10 lb-ft14 Nm
- Panel Bolts10 lb-ft14 Nm
- Striker Bolts25 lb-ft34 Nm
- Trim ClipsReplace if broken2 lb-ft3 Nm
Hood Strut6 specs
- Body Panel Bolts18 lb-ft25 Nm
- Hinge Bolts20 lb-ft27 Nm
- Latch Bolts10 lb-ft14 Nm
- Panel Bolts10 lb-ft14 Nm
- Striker Bolts25 lb-ft34 Nm
- Trim ClipsReplace if broken2 lb-ft3 Nm
Liftgate7 specs
- Body Panel Bolts18 lb-ft25 Nm
- Door Hinge Bolts22 lb-ft30 Nm
- Hinge Bolts20 lb-ft27 Nm
- Latch Bolts10 lb-ft14 Nm
- Panel Bolts10 lb-ft14 Nm
- Striker Bolts25 lb-ft34 Nm
- Trim ClipsReplace if broken2 lb-ft3 Nm
Liftgate Motor6 specs
- Body Panel Bolts18 lb-ft25 Nm
- Hinge Bolts20 lb-ft27 Nm
- Latch Bolts10 lb-ft14 Nm
- Panel Bolts10 lb-ft14 Nm
- Striker Bolts25 lb-ft34 Nm
- Trim ClipsReplace if broken2 lb-ft3 Nm
Liftgate Strut6 specs
- Body Panel Bolts18 lb-ft25 Nm
- Hinge Bolts20 lb-ft27 Nm
- Latch Bolts10 lb-ft14 Nm
- Panel Bolts10 lb-ft14 Nm
- Striker Bolts25 lb-ft34 Nm
- Trim ClipsReplace if broken2 lb-ft3 Nm
Quarter Glass6 specs
- Body Panel Bolts18 lb-ft25 Nm
- Hinge Bolts20 lb-ft27 Nm
- Latch Bolts10 lb-ft14 Nm
- Panel Bolts10 lb-ft14 Nm
- Striker Bolts25 lb-ft34 Nm
- Trim ClipsReplace if broken2 lb-ft3 Nm
Quarter Panel8 specs
- Body Panel Bolts18 lb-ft25 Nm
- Bumper Cover Bolts7 lb-ft10 Nm
- Door Hinge Bolts22 lb-ft30 Nm
- Hinge Bolts20 lb-ft27 Nm
- Latch Bolts10 lb-ft14 Nm
- Panel Bolts10 lb-ft14 Nm
- Striker Bolts25 lb-ft34 Nm
- Trim ClipsReplace if broken2 lb-ft3 Nm
Rear Window6 specs
- Body Panel Bolts18 lb-ft25 Nm
- Hinge Bolts20 lb-ft27 Nm
- Latch Bolts10 lb-ft14 Nm
- Panel Bolts10 lb-ft14 Nm
- Striker Bolts25 lb-ft34 Nm
- Trim ClipsReplace if broken2 lb-ft3 Nm
Rocker Panel8 specs
- Body Panel Bolts18 lb-ft25 Nm
- Bumper Cover Bolts7 lb-ft10 Nm
- Door Hinge Bolts22 lb-ft30 Nm
- Hinge Bolts20 lb-ft27 Nm
- Latch Bolts10 lb-ft14 Nm
- Panel Bolts10 lb-ft14 Nm
- Striker Bolts25 lb-ft34 Nm
- Trim ClipsReplace if broken2 lb-ft3 Nm
Side Mirror Glass5 specs
- Hinge Bolts20 lb-ft27 Nm
- Latch Bolts10 lb-ft14 Nm
- Panel Bolts10 lb-ft14 Nm
- Striker Bolts25 lb-ft34 Nm
- Trim ClipsReplace if broken2 lb-ft3 Nm
Trunk Hinge7 specs
- Body Panel Bolts18 lb-ft25 Nm
- Door Hinge Bolts22 lb-ft30 Nm
- Hinge Bolts20 lb-ft27 Nm
- Latch Bolts10 lb-ft14 Nm
- Panel Bolts10 lb-ft14 Nm
- Striker Bolts25 lb-ft34 Nm
- Trim ClipsReplace if broken2 lb-ft3 Nm
Trunk Latch6 specs
- Body Panel Bolts18 lb-ft25 Nm
- Hinge Bolts20 lb-ft27 Nm
- Latch Bolts10 lb-ft14 Nm
- Panel Bolts10 lb-ft14 Nm
- Striker Bolts25 lb-ft34 Nm
- Trim ClipsReplace if broken2 lb-ft3 Nm
Trunk Lid7 specs
- Hinge Bolts20 lb-ft27 Nm
- Latch Bolts10 lb-ft14 Nm
- Panel Bolts10 lb-ft14 Nm
- Striker Bolts25 lb-ft34 Nm
- Trim ClipsReplace if broken2 lb-ft3 Nm
- Trunk Hinge Bolts18 lb-ft25 Nm
- Trunk Latch Bolts9 lb-ft12 Nm
Trunk Strut6 specs
- Body Panel Bolts18 lb-ft25 Nm
- Hinge Bolts20 lb-ft27 Nm
- Latch Bolts10 lb-ft14 Nm
- Panel Bolts10 lb-ft14 Nm
- Striker Bolts25 lb-ft34 Nm
- Trim ClipsReplace if broken2 lb-ft3 Nm
Windshield6 specs
- Body Panel Bolts18 lb-ft25 Nm
- Hinge Bolts20 lb-ft27 Nm
- Latch Bolts10 lb-ft14 Nm
- Panel Bolts10 lb-ft14 Nm
- Striker Bolts25 lb-ft34 Nm
- Trim ClipsReplace if broken2 lb-ft3 Nm
Windshield Molding5 specs
- Hinge Bolts20 lb-ft27 Nm
- Latch Bolts10 lb-ft14 Nm
- Panel Bolts10 lb-ft14 Nm
- Striker Bolts25 lb-ft34 Nm
- Trim ClipsReplace if broken2 lb-ft3 Nm

Interior

Armrest2 specs
- Connector Bolts5 lb-ft7 Nm
- Trim Panel ClipsReplace if damaged1.5 lb-ft2 Nm
Carpet4 specs
- Connector Bolts5 lb-ft7 Nm
- Dashboard Screws2 lb-ft3 Nm
- Seat Mounting BoltsSafety critical33 lb-ft45 Nm
- Trim Panel ClipsReplace if damaged1.5 lb-ft2 Nm
Center Console3 specs
- Connector Bolts5 lb-ft7 Nm
- Console Screws2 lb-ft3 Nm
- Shifter Trim4 lb-ft5 Nm
Dash Pad4 specs
- Connector Bolts5 lb-ft7 Nm
- Dashboard Screws2 lb-ft3 Nm
- Seat Mounting BoltsSafety critical33 lb-ft45 Nm
- Trim Panel ClipsReplace if damaged1.5 lb-ft2 Nm
Dashboard4 specs
- Connector Bolts5 lb-ft7 Nm
- Dashboard Bolt9 lb-ft12 Nm
- Dashboard Screws2 lb-ft3 Nm
- Trim Panel ClipsReplace if damaged1.5 lb-ft2 Nm
Door Panel3 specs
- Connector Bolts5 lb-ft7 Nm
- Door Panel Screws1.5 lb-ft2 Nm
- Trim Panel ClipsReplace if damaged1.5 lb-ft2 Nm
Floor Mat Hooks2 specs
- Connector Bolts5 lb-ft7 Nm
- Trim Panel ClipsReplace if damaged1.5 lb-ft2 Nm
Glove Box3 specs
- Connector Bolts5 lb-ft7 Nm
- Glove Box Screws2 lb-ft3 Nm
- Hinge Screws1.5 lb-ft2 Nm
Glove Box Latch3 specs
- Connector Bolts5 lb-ft7 Nm
- Dashboard Screws2 lb-ft3 Nm
- Trim Panel ClipsReplace if damaged1.5 lb-ft2 Nm
Headliner3 specs
- Connector Bolts5 lb-ft7 Nm
- Seat Mounting BoltsSafety critical33 lb-ft45 Nm
- Trim Panel ClipsReplace if damaged1.5 lb-ft2 Nm
Pedal Pads2 specs
- Connector Bolts5 lb-ft7 Nm
- Trim Panel ClipsReplace if damaged1.5 lb-ft2 Nm
Rearview Mirror2 specs
- Connector Bolts5 lb-ft7 Nm
- Trim Panel ClipsReplace if damaged1.5 lb-ft2 Nm
Seat - Front4 specs
- Connector Bolts5 lb-ft7 Nm
- Electrical Connectors4 lb-ft5 Nm
- Seat Mounting BoltsSafety critical33 lb-ft45 Nm
- Seat Track Bolts33 lb-ft45 Nm
Seat - Rear3 specs
- Connector Bolts5 lb-ft7 Nm
- Seat Back Release11 lb-ft15 Nm
- Seat Mounting Bolts26 lb-ft35 Nm
Seat Belt3 specs
- Connector Bolts5 lb-ft7 Nm
- Seat Mounting BoltsSafety critical33 lb-ft45 Nm
- Trim Panel ClipsReplace if damaged1.5 lb-ft2 Nm
Seat Belt Buckle3 specs
- Connector Bolts5 lb-ft7 Nm
- Seat Mounting BoltsSafety critical33 lb-ft45 Nm
- Trim Panel ClipsReplace if damaged1.5 lb-ft2 Nm
Seat Belt Pretensioner3 specs
- Connector Bolts5 lb-ft7 Nm
- Seat Mounting BoltsSafety critical33 lb-ft45 Nm
- Trim Panel ClipsReplace if damaged1.5 lb-ft2 Nm
Seat Cover3 specs
- Connector Bolts5 lb-ft7 Nm
- Seat Mounting BoltsSafety critical33 lb-ft45 Nm
- Trim Panel ClipsReplace if damaged1.5 lb-ft2 Nm
Seat Foam3 specs
- Connector Bolts5 lb-ft7 Nm
- Seat Mounting BoltsSafety critical33 lb-ft45 Nm
- Trim Panel ClipsReplace if damaged1.5 lb-ft2 Nm
Seat Track3 specs
- Connector Bolts5 lb-ft7 Nm
- Seat Mounting BoltsSafety critical33 lb-ft45 Nm
- Trim Panel ClipsReplace if damaged1.5 lb-ft2 Nm
Shifter Boot2 specs
- Connector Bolts5 lb-ft7 Nm
- Trim Panel ClipsReplace if damaged1.5 lb-ft2 Nm
Shifter Knob2 specs
- Connector Bolts5 lb-ft7 Nm
- Trim Panel ClipsReplace if damaged1.5 lb-ft2 Nm
Steering Wheel Cover2 specs
- Connector Bolts5 lb-ft7 Nm
- Trim Panel ClipsReplace if damaged. Verify sequence with the service manual1.5 lb-ft2 Nm
Sun Visor2 specs
- Connector Bolts5 lb-ft7 Nm
- Visor Mounting Screws2 lb-ft3 Nm

Torque is shown in lb-ft with Nm below it. Where a step says to turn, tighten the listed angle after the torque step before it. Use new bolts where the note says so.

Need labor times, fluids or repair steps for this car? See it on the Open Labor Project