2002 Ford Windstar torque specs

3.8L Essex V6

Change vehicle

Most looked up

Lug nuts100 lb-ft135 Nm
Oil drain plug20 lb-ft27 Nm
Spark plugs15 lb-ft20 Nm
Front caliper bracket bolts100 lb-ft136 Nm
Rear caliper bracket bolts74 lb-ft100 Nm
Front axle nut184 lb-ft250 Nm
Outer tie rod end nut40.6 lb-ft55 Nm

Maintenance

Air Filter2 specs
- Air Box ClipsTool-free2 lb-ft3 Nm
- MAF Sensor Screws3 lb-ft4 Nm
Differential Service3 specs
- Differential Cover Bolts22.1 lb-ft30 Nm
- Ring Gear Bolt81.1 lb-ft110 Nm
- Fill Plug25.8 lb-ft35 Nm
Tire Rotation2 specs
- Lug Nuts - Alloy WheelsTorque in star pattern, recheck after 50 miles100 lb-ft135 Nm
- Lug Nuts - Steel WheelsTorque in star pattern100 lb-ft135 Nm
Wheel Alignment2 specs
- Cam Bolt (adjustment)88.5 lb-ft120 Nm
- Tie Rod Lock Nut47.9 lb-ft65 Nm

Brakes

ABS Module2 specs
- ABS Module Mounting Bolt7.4 lb-ft10 Nm
- Brake Line Fitting11.1 lb-ft15 Nm
ABS Pump2 specs
- ABS Module Mounting Bolt7.4 lb-ft10 Nm
- Brake Line Fitting11.1 lb-ft15 Nm
Brake Caliper - Front3 specs
- Bleeder ScrewDo not overtighten7 lb-ft10 Nm
- Brake Line Banjo BoltUse new copper washers18 lb-ft25 Nm
- Caliper Bracket BoltsThreadlocker recommended100 lb-ft136 Nm
Brake Caliper - Rear3 specs
- Bleeder ScrewDo not overtighten7 lb-ft10 Nm
- Brake Line Banjo BoltUse new copper washers18 lb-ft25 Nm
- Caliper Bracket BoltsThreadlocker recommended74 lb-ft100 Nm
Brake Master Cylinder2 specs
- Brake Line FittingsUse flare nut wrench11 lb-ft15 Nm
- Master Cylinder Nuts18 lb-ft25 Nm
Brake Master Cylinder Rebuild3 specs
- Brake Line FittingsUse flare nut wrench11 lb-ft15 Nm
- Master Cylinder Mounting Nuts18 lb-ft25 Nm
- Reservoir Mounting Bolts6 lb-ft8 Nm
Brake Pads - Front3 specs
- Caliper Bracket BoltsThreadlocker recommended100 lb-ft136 Nm
- Caliper Slide Pin BoltsApply silicone brake grease26 lb-ft35 Nm
- Wheel Lug NutsTorque in star pattern100 lb-ft135 Nm
Brake Pads - Rear3 specs
- Caliper Bracket BoltsThreadlocker recommended74 lb-ft100 Nm
- Caliper Slide Pin BoltsApply silicone brake grease22 lb-ft30 Nm
- Wheel Lug NutsTorque in star pattern100 lb-ft135 Nm
Brake Pads and Rotors - Front3 specs
- Caliper Bracket Bolts100 lb-ft136 Nm
- Caliper Slide Pin25.8 lb-ft35 Nm
- Wheel Lug Nut100 lb-ft135 Nm
Brake Pads and Rotors - Rear3 specs
- Caliper Bracket Bolts73.8 lb-ft100 Nm
- Caliper Slide Pin25.8 lb-ft35 Nm
- Wheel Lug Nut100 lb-ft135 Nm
Brake Rotor - Front Single8 specs
- Brake Rotor Set Screw5 lb-ft7 Nm
- Caliper Bracket Bolts100 lb-ft136 Nm
- Caliper Mounting Bolts68 lb-ft93 Nm
- Hub NutIf removed184 lb-ft250 Nm
- Wheel Lug NutsTorque in star pattern100 lb-ft135 Nm
- Caliper Bracket Bolts100 lb-ft136 Nm
- Caliper Slide Pin25.8 lb-ft35 Nm
- Wheel Lug Nut100 lb-ft135 Nm
Brake Rotor - Rear Single8 specs
- Brake Rotor Set Screw5 lb-ft7 Nm
- Caliper Bracket Bolts79 lb-ft107 Nm
- Caliper Mounting Bolts68 lb-ft93 Nm
- Hub NutIf removed189 lb-ft256 Nm
- Wheel Lug NutsTorque in star pattern100 lb-ft135 Nm
- Caliper Bracket Bolts73.8 lb-ft100 Nm
- Caliper Slide Pin25.8 lb-ft35 Nm
- Wheel Lug Nut100 lb-ft135 Nm
Brake Rotors - Front Pair3 specs
- Caliper Bracket Bolts100 lb-ft136 Nm
- Caliper Slide Pin25.8 lb-ft35 Nm
- Wheel Lug Nut100 lb-ft135 Nm
Brake Rotors - Rear Pair3 specs
- Caliper Bracket Bolts73.8 lb-ft100 Nm
- Caliper Slide Pin25.8 lb-ft35 Nm
- Wheel Lug Nut100 lb-ft135 Nm
Front Brake Pad Replacement3 specs
- Caliper Bracket BoltsThreadlocker recommended100 lb-ft136 Nm
- Caliper Slide Pin BoltsApply silicone brake grease26 lb-ft35 Nm
- Wheel Lug NutsTorque in star pattern100 lb-ft135 Nm
Rear Brake Shoe Replacement3 specs
- Backing Plate Bolts44 lb-ft60 Nm
- Wheel Cylinder Bolts9 lb-ft12 Nm
- Wheel Lug NutsTorque in star pattern100 lb-ft135 Nm

Engine

Cylinder Head R&R1 spec
- Cylinder Head Bolt (TTY)55.3 lb-ft75 Nm
Cylinder Head Resurface1 spec
- Cylinder Head Bolt (TTY)55.3 lb-ft75 Nm
Engine Mount - Front3 specs
- Engine Mount Through-Bolt63 lb-ft85 Nm
- Engine Mount-to-Block Bolts48 lb-ft65 Nm
- Engine Mount-to-Frame Bolts55 lb-ft75 Nm
Engine Mount - Rear2 specs
- Engine Mount Through-Bolt62.7 lb-ft85 Nm
- Engine Mount Bracket Bolt55.3 lb-ft75 Nm
Engine Mounts - All2 specs
- Engine Mount Through-Bolt62.7 lb-ft85 Nm
- Engine Mount Bracket Bolt55.3 lb-ft75 Nm
Exhaust Manifold1 spec
- Exhaust Manifold Stud Nut29.5 lb-ft40 Nm
Exhaust Manifold Gasket3 specs
- Exhaust Manifold NutsApply anti-seize, work hot-to-cold22 lb-ft30 Nm
- Exhaust Manifold StudsIf replacing studs11 lb-ft15 Nm
- Heat Shield Bolts7 lb-ft10 Nm
Fan Belt Replacement3 specs
- Idler Pulley Bolt30 lb-ft40 Nm
- Tensioner Bolt18 lb-ft25 Nm
- Tensioner Pulley Bolt33 lb-ft45 Nm
Flexplate1 spec
- Flywheel/Flexplate Bolt70.1 lb-ft95 Nm
Full Engine Tune-Up5 specs
- Ignition Coil Bolt6 lb-ft8 Nm
- Spark Plugs - Aluminum HeadApply anti-seize to threads15 lb-ft20 Nm
- Spark Plugs - Cast Iron HeadApply anti-seize to threads22 lb-ft30 Nm
- Throttle Body Bolts7 lb-ft10 Nm
- Valve Cover BoltsTighten in sequence7 lb-ft10 Nm
Head Gasket - Single6 specs
- Exhaust Manifold NutsApply anti-seize18 lb-ft25 Nm
- Intake Manifold BoltTighten in sequence18 lb-ft25 Nm
- Cylinder Head Bolts - Step 1Always use new TTY bolts30 lb-ft40 Nm
- Cylinder Head Bolts - Step 2Tighten in sequence59 lb-ft80 Nm
- Cylinder Head Bolts - Step 3Plus 90 degreesTurn 90°
- Cylinder Head Bolts - Step 4Plus 90 degreesTurn 90°
Head Gaskets - Both1 spec
- Cylinder Head Bolt (TTY)55.3 lb-ft75 Nm
Intake Manifold2 specs
- Intake Manifold Bolt18.4 lb-ft25 Nm
- Throttle Body Bolt7.4 lb-ft10 Nm
Intake Manifold Gasket3 specs
- Fuel Rail Bolts9 lb-ft12 Nm
- Intake Manifold BoltTighten in sequence from center out18 lb-ft25 Nm
- Throttle Body Bolts7 lb-ft10 Nm
Oil Change2 specs
- Oil Drain PlugUse new crush washer20 lb-ft27 Nm
- Oil Filter (Spin-On)Hand tight plus 3/4 turn15 lb-ft20 Nm
Oil Pan Gasket2 specs
- Oil Drain PlugUse new crush washer26 lb-ft35 Nm
- Oil Pan BoltTighten in sequence from center outward9 lb-ft12 Nm
Oil Pan Replacement2 specs
- Oil Pan Bolt13.3 lb-ft18 Nm
- Oil Drain Plug29.5 lb-ft40 Nm
Serpentine Belt2 specs
- Belt Tensioner Bolt41 lb-ft55 Nm
- Idler Pulley Bolt33 lb-ft45 Nm
Serpentine Belt Tensioner1 spec
- Belt Tensioner Bolt29.5 lb-ft40 Nm
Throttle Body2 specs
- Air Intake Hose Clamps2 lb-ft3 Nm
- Throttle Body Bolts7 lb-ft10 Nm
Transmission Mount4 specs
- Crossmember Bolt70 lb-ft95 Nm
- Transmission Mount Bolts48 lb-ft65 Nm
- Transmission Mount Bolts59 lb-ft80 Nm
- Crossmember Bolt73.8 lb-ft100 Nm
Valve Cover Gasket - Single2 specs
- Spark Plug Tube SealsIf equipped with separate seals9 lb-ft12 Nm
- Valve Cover BoltsTighten in sequence7 lb-ft10 Nm
Valve Cover Gaskets - Both1 spec
- Valve Cover Bolts8.9 lb-ft12 Nm
Valve Spring - Single2 specs
- Strut Tower Nut36.9 lb-ft50 Nm
- Wheel Lug Nut100 lb-ft135 Nm
Valve Springs - All2 specs
- Strut Pinch Bolt66.4 lb-ft90 Nm
- Wheel Lug Nut100 lb-ft135 Nm

Cooling

Coolant Flush5 specs
- Bleed ScrewOpen during fill5 lb-ft7 Nm
- Block Drain PlugIf equipped, use new washer18 lb-ft25 Nm
- Drain PetcockHand tight5 lb-ft7 Nm
- Hose Clamps3 lb-ft4 Nm
- Pump Bolts19 lb-ft26 Nm
Cooling Fan Clutch2 specs
- Pressure Plate Bolt25.8 lb-ft35 Nm
- Transmission Bell Housing Bolt51.6 lb-ft70 Nm
Heater Core2 specs
- Heater Core Hose Clamp2.2 lb-ft3 Nm
- Dashboard Bolt7.4 lb-ft10 Nm
Radiator4 specs
- Drain PetcockPlastic - hand tight4 lb-ft5 Nm
- Radiator Mounting BoltDo not overtighten plastic mounts9 lb-ft12 Nm
- Transmission Cooler LinesIf equipped18 lb-ft25 Nm
- Upper/Lower Hose Clamps2 lb-ft3 Nm
Radiator Removal and Service4 specs
- Drain PetcockPlastic - hand-tight only4 lb-ft5 Nm
- Fan Shroud Bolts7 lb-ft10 Nm
- Radiator Mounting BoltDo not overtighten plastic mounts9 lb-ft12 Nm
- Transmission Cooler LinesIf equipped, use new washers18 lb-ft25 Nm
Thermostat2 specs
- Coolant Temperature SensorUse thread sealant15 lb-ft20 Nm
- Thermostat Housing Bolt11 lb-ft15 Nm
Thermostat Housing1 spec
- Thermostat Housing Bolt14.8 lb-ft20 Nm
Water Pump3 specs
- Hose ClampsSpring clamps preferred2 lb-ft3 Nm
- Thermostat Housing Bolt11 lb-ft15 Nm
- Water Pump BoltsTighten in criss-cross pattern18 lb-ft25 Nm

Ignition

Spark Plug Wires2 specs
- Spark Plug18.4 lb-ft25 Nm
- Ignition Coil Bolt5.9 lb-ft8 Nm
Spark Plugs5 specs
- Engine Cover Clips2 lb-ft3 Nm
- Ignition Coil Bolt6 lb-ft8 Nm
- Spark PlugGap before install16 lb-ft21 Nm
- Spark Plugs - Aluminum HeadApply anti-seize to threads15 lb-ft20 Nm
- Spark Plugs - Cast Iron HeadApply anti-seize to threads22 lb-ft30 Nm

Fuel system

Fuel Filter2 specs
- Fuel Filter Bracket Bolt7 lb-ft10 Nm
- Fuel Line FittingsIf threaded type18 lb-ft25 Nm
Fuel Pump2 specs
- Fuel Pump Module Lock RingUse special tool59 lb-ft80 Nm
- Tank Strap Bolts26 lb-ft35 Nm
Fuel Pump Module2 specs
- Fuel Pump Lock Ring40.6 lb-ft55 Nm
- Fuel Line Fitting18.4 lb-ft25 Nm
Fuel Tank2 specs
- Fuel Tank Strap Bolt25.8 lb-ft35 Nm
- Fuel Filler Neck Clamp3.7 lb-ft5 Nm
Fuel Tank Strap2 specs
- Fuel Tank Strap Bolt25.8 lb-ft35 Nm
- Fuel Filler Neck Clamp3.7 lb-ft5 Nm
High Pressure Fuel Pump2 specs
- Fuel Pump Lock Ring40.6 lb-ft55 Nm
- Fuel Line Fitting18.4 lb-ft25 Nm

Electrical

Alternator4 specs
- Alternator Mounting Bolts37 lb-ft50 Nm
- Alternator Pivot Bolt18 lb-ft25 Nm
- Battery Terminal BoltsDo not overtighten6 lb-ft8 Nm
- Serpentine Belt Tensioner41 lb-ft55 Nm
Alternator Belt2 specs
- Alternator Mounting Bolt36.9 lb-ft50 Nm
- Alternator Pivot Bolt29.5 lb-ft40 Nm
Battery3 specs
- Battery Hold-Down Bolt6 lb-ft8 Nm
- Battery Terminal BoltsDo not overtighten - can crack terminal4 lb-ft6 Nm
- Battery Tray Bolts9 lb-ft12 Nm
Blower Motor2 specs
- Blower Motor Mounting Screw3 lb-ft4 Nm
- Blower Motor Resistor Screws1.5 lb-ft2 Nm
Blower Motor Control Module1 spec
- Blower Motor Mounting Screw3.7 lb-ft5 Nm
Blower Motor Resistor1 spec
- Blower Motor Mounting Screw3.7 lb-ft5 Nm
Door Lock Actuator - Front1 spec
- Door Latch Bolt7.4 lb-ft10 Nm
Door Lock Actuator - Rear1 spec
- Door Latch Bolt7.4 lb-ft10 Nm
Fuel Pump Relay2 specs
- Fuel Pump Lock Ring40.6 lb-ft55 Nm
- Fuel Line Fitting18.4 lb-ft25 Nm
Power Window Motor - Front2 specs
- Window Regulator Bolt7.4 lb-ft10 Nm
- Door Panel Screws2.2 lb-ft3 Nm
Power Window Motor - Rear2 specs
- Window Regulator Bolt7.4 lb-ft10 Nm
- Door Panel Screws2.2 lb-ft3 Nm
Power Window Regulator - Front2 specs
- Window Regulator Bolt7.4 lb-ft10 Nm
- Door Panel Screws2.2 lb-ft3 Nm
Power Window Regulator - Rear2 specs
- Window Regulator Bolt7.4 lb-ft10 Nm
- Door Panel Screws2.2 lb-ft3 Nm
Starter3 specs
- Heat Shield BoltsIf equipped7 lb-ft10 Nm
- Starter Mounting BoltLong bolt may need extension37 lb-ft50 Nm
- Starter Solenoid NutFor B+ cable9 lb-ft12 Nm
Starter Solenoid1 spec
- Starter Mounting Bolt40.6 lb-ft55 Nm
Window Motor and Regulator - Front2 specs
- Window Regulator Bolt7.4 lb-ft10 Nm
- Door Panel Screws2.2 lb-ft3 Nm
Window Motor and Regulator - Rear2 specs
- Window Regulator Bolt7.4 lb-ft10 Nm
- Door Panel Screws2.2 lb-ft3 Nm

Suspension

Ball Joint - Lower7 specs
- Control Arm Bolts100 lb-ft135 Nm
- Lower Ball Joint Nut68 lb-ft93 Nm
- Pinch BoltNew bolt47 lb-ft64 Nm
- Wheel Lug Nuts100 lb-ft135 Nm
- Ball Joint Pinch Bolt40.6 lb-ft55 Nm
- Lower Ball Joint Castle Nut70.1 lb-ft95 Nm
- Wheel Lug Nut100 lb-ft135 Nm
Ball Joints - Upper and Lower3 specs
- Ball Joint Pinch Bolt40.6 lb-ft55 Nm
- Lower Ball Joint Castle Nut70.1 lb-ft95 Nm
- Wheel Lug Nut100 lb-ft135 Nm
Coil Spring - Front3 specs
- Strut Tower Nut36.9 lb-ft50 Nm
- Strut Pinch Bolt66.4 lb-ft90 Nm
- Wheel Lug Nut100 lb-ft135 Nm
Coil Spring - Rear3 specs
- Strut Tower Nut36.9 lb-ft50 Nm
- Strut Pinch Bolt66.4 lb-ft90 Nm
- Wheel Lug Nut100 lb-ft135 Nm
Coil Springs - Front Pair3 specs
- Strut Tower Nut36.9 lb-ft50 Nm
- Strut Pinch Bolt66.4 lb-ft90 Nm
- Wheel Lug Nut100 lb-ft135 Nm
Coil Springs - Rear Pair3 specs
- Strut Tower Nut36.9 lb-ft50 Nm
- Strut Pinch Bolt66.4 lb-ft90 Nm
- Wheel Lug Nut100 lb-ft135 Nm
Control Arm Bushing - Front Lower3 specs
- Control Arm Pivot Bolt88.5 lb-ft120 Nm
- Ball Joint Pinch Bolt40.6 lb-ft55 Nm
- Wheel Lug Nut100 lb-ft135 Nm
Control Arm Bushing - Rear3 specs
- Control Arm Pivot Bolt88.5 lb-ft120 Nm
- Ball Joint Pinch Bolt40.6 lb-ft55 Nm
- Wheel Lug Nut100 lb-ft135 Nm
Front Struts - Pair8 specs
- Control Arm Bolts100 lb-ft135 Nm
- Strut to Knuckle Bolts95 lb-ft128 Nm
- Strut Tower Nuts37 lb-ft50 Nm
- Sway Bar Link47 lb-ft64 Nm
- Wheel Lug Nuts100 lb-ft135 Nm
- Strut Tower Nut36.9 lb-ft50 Nm
- Strut Pinch Bolt66.4 lb-ft90 Nm
- Wheel Lug Nut100 lb-ft135 Nm
Front Suspension Rebuild4 specs
- Ball Joint Pinch BoltUse new bolt if locknut style37 lb-ft50 Nm
- Lower Control Arm BoltsTorque at ride height81 lb-ft110 Nm
- Strut Top Mount Nuts18 lb-ft25 Nm
- Sway Bar End Link Nuts44 lb-ft60 Nm
Lower Control Arm - Front3 specs
- Control Arm Pivot Bolt88.5 lb-ft120 Nm
- Ball Joint Pinch Bolt40.6 lb-ft55 Nm
- Wheel Lug Nut100 lb-ft135 Nm
Lower Control Arm - Rear3 specs
- Control Arm Pivot Bolt88.5 lb-ft120 Nm
- Ball Joint Pinch Bolt40.6 lb-ft55 Nm
- Wheel Lug Nut100 lb-ft135 Nm
Rear Shocks - Pair6 specs
- Lower Shock Bolt68 lb-ft93 Nm
- Upper Shock Mount Nut21 lb-ft28 Nm
- Wheel Lug Nuts100 lb-ft135 Nm
- Strut Tower Nut36.9 lb-ft50 Nm
- Strut Pinch Bolt66.4 lb-ft90 Nm
- Wheel Lug Nut100 lb-ft135 Nm
Rear Suspension Service4 specs
- Lower Control Arm BoltsTorque at ride height66 lb-ft90 Nm
- Shock Lower Bolt52 lb-ft70 Nm
- Sway Bar End Link Nuts37 lb-ft50 Nm
- Trailing Arm BoltsTorque at ride height88 lb-ft120 Nm
Shock Absorber Replacement2 specs
- Lower Mount Bolt66 lb-ft90 Nm
- Upper Mount NutUse new self-locking nut41 lb-ft55 Nm
Strut Assembly - Front4 specs
- Strut Mount Center NutHold strut shaft with Allen key41 lb-ft55 Nm
- Strut to Knuckle BoltsOften TTY111 lb-ft150 Nm
- Strut Tower NutsDo not loosen center nut unless compressed37 lb-ft50 Nm
- Sway Bar End Link Nuts41 lb-ft55 Nm
Strut Assembly - Rear7 specs
- Control Arm Bolts100 lb-ft135 Nm
- Strut Tower Nuts37 lb-ft50 Nm
- Sway Bar Link47 lb-ft64 Nm
- Wheel Lug Nuts100 lb-ft135 Nm
- Strut Tower Nut36.9 lb-ft50 Nm
- Strut Pinch Bolt66.4 lb-ft90 Nm
- Wheel Lug Nut100 lb-ft135 Nm
Strut Bearing3 specs
- Strut Tower Nut36.9 lb-ft50 Nm
- Strut Pinch Bolt66.4 lb-ft90 Nm
- Wheel Lug Nut100 lb-ft135 Nm
Strut Mount - Front3 specs
- Strut Tower Nut36.9 lb-ft50 Nm
- Strut Pinch Bolt66.4 lb-ft90 Nm
- Wheel Lug Nut100 lb-ft135 Nm
Strut Mount - Rear3 specs
- Strut Tower Nut36.9 lb-ft50 Nm
- Strut Pinch Bolt66.4 lb-ft90 Nm
- Wheel Lug Nut100 lb-ft135 Nm
Subframe1 spec
- Subframe Bolts110.6 lb-ft150 Nm
Subframe Bushing1 spec
- Subframe Bolts110.6 lb-ft150 Nm
Sway Bar Link - Front2 specs
- Sway Bar Link Nuts44.3 lb-ft60 Nm
- Wheel Lug Nut100 lb-ft135 Nm
Sway Bar Link - Rear2 specs
- Sway Bar Link Nuts44.3 lb-ft60 Nm
- Wheel Lug Nut100 lb-ft135 Nm
Sway Bar Links - Front Pair2 specs
- Sway Bar Link Nuts44.3 lb-ft60 Nm
- Wheel Lug Nut100 lb-ft135 Nm
Upper Control Arm - Rear3 specs
- Control Arm Pivot Bolt88.5 lb-ft120 Nm
- Ball Joint Pinch Bolt40.6 lb-ft55 Nm
- Wheel Lug Nut100 lb-ft135 Nm

Steering

Power Steering Fluid Flush5 specs
- Pressure Line FittingNew O-ring26 lb-ft36 Nm
- Pump Mounting Bolts21 lb-ft28 Nm
- Steering Rack Bolts79 lb-ft107 Nm
- Tie Rod Nut42 lb-ft57 Nm
- Wheel Lug Nuts100 lb-ft135 Nm
Power Steering Pump8 specs
- High Pressure Hose FittingUse new O-rings18 lb-ft25 Nm
- Power Steering Pump Bolts18 lb-ft25 Nm
- Pressure Line FittingUse new O-rings22 lb-ft30 Nm
- Pulley NutHold pulley with pin spanner52 lb-ft70 Nm
- Pump Mounting Bolts18 lb-ft25 Nm
- Return Hose Clamp2 lb-ft3 Nm
- Return Line Clamp3 lb-ft4 Nm
- Serpentine Belt Tensioner41 lb-ft55 Nm
Power Steering Rack3 specs
- Steering Rack Bolts70.1 lb-ft95 Nm
- Tie Rod End Nut40.6 lb-ft55 Nm
- Steering Line Fitting18.4 lb-ft25 Nm
Tie Rod Assembly3 specs
- Tie Rod End Castle Nut40.6 lb-ft55 Nm
- Tie Rod Lock Nut47.9 lb-ft65 Nm
- Wheel Lug Nut100 lb-ft135 Nm
Tie Rod End - Inner3 specs
- Tie Rod End Castle Nut40.6 lb-ft55 Nm
- Tie Rod Lock Nut47.9 lb-ft65 Nm
- Wheel Lug Nut100 lb-ft135 Nm
Tie Rod End - Outer6 specs
- Tie Rod End NutNew cotter pin42 lb-ft57 Nm
- Tie Rod Nut42 lb-ft57 Nm
- Wheel Lug Nuts100 lb-ft135 Nm
- Tie Rod End Castle Nut40.6 lb-ft55 Nm
- Tie Rod Lock Nut47.9 lb-ft65 Nm
- Wheel Lug Nut100 lb-ft135 Nm
Tie Rods - Both Sides3 specs
- Tie Rod End Castle Nut40.6 lb-ft55 Nm
- Tie Rod Lock Nut47.9 lb-ft65 Nm
- Wheel Lug Nut100 lb-ft135 Nm

Drivetrain

CV Axle - Front5 specs
- CV Bolts47 lb-ft64 Nm
- Lower Ball Joint Nut79 lb-ft107 Nm
- Wheel Lug Nuts100 lb-ft135 Nm
- Axle Nut184 lb-ft250 Nm
- Wheel Lug Nut100 lb-ft135 Nm
CV Axles - Front Pair2 specs
- Axle Nut184 lb-ft250 Nm
- Wheel Lug Nut100 lb-ft135 Nm
Differential Rebuild - Rear3 specs
- Differential Cover Bolts22.1 lb-ft30 Nm
- Ring Gear Bolt81.1 lb-ft110 Nm
- Fill Plug25.8 lb-ft35 Nm
Limited Slip Clutch Pack3 specs
- Pressure Plate Bolt25.8 lb-ft35 Nm
- Flywheel Bolts70.1 lb-ft95 Nm
- Transmission Bell Housing Bolt51.6 lb-ft70 Nm
Wheel Bearing - Press-In Front3 specs
- Hub Nut / Axle Nut206.5 lb-ft280 Nm
- Wheel Bearing Bolts55.3 lb-ft75 Nm
- Wheel Lug Nut100 lb-ft135 Nm
Wheel Bearing - Press-In Rear3 specs
- Hub Nut / Axle Nut206.5 lb-ft280 Nm
- Wheel Bearing Bolts55.3 lb-ft75 Nm
- Wheel Lug Nut100 lb-ft135 Nm
Wheel Bearing Hub - Front10 specs
- ABS Sensor BoltDo not overtighten7 lb-ft10 Nm
- Axle NutUse new cotter pin after torque184 lb-ft250 Nm
- Caliper Bracket Bolts88 lb-ft120 Nm
- Control Arm Bolts100 lb-ft135 Nm
- Hub Bolts79 lb-ft107 Nm
- Wheel Bearing Hub BoltsApply threadlocker if specified81 lb-ft110 Nm
- Wheel Lug Nuts100 lb-ft135 Nm
- Hub Nut / Axle Nut206.5 lb-ft280 Nm
- Wheel Bearing Bolts55.3 lb-ft75 Nm
- Wheel Lug Nut100 lb-ft135 Nm
Wheel Bearing Hub - Rear10 specs
- ABS Sensor Bolt8 lb-ft11 Nm
- Axle NutUse new cotter pin after torque148 lb-ft200 Nm
- Caliper Bracket Bolts81 lb-ft110 Nm
- Control Arm Bolts100 lb-ft135 Nm
- Hub Bolts79 lb-ft107 Nm
- Wheel Bearing Hub BoltsApply threadlocker if specified74 lb-ft100 Nm
- Wheel Lug Nuts100 lb-ft135 Nm
- Hub Nut / Axle Nut206.5 lb-ft280 Nm
- Wheel Bearing Bolts55.3 lb-ft75 Nm
- Wheel Lug Nut100 lb-ft135 Nm

Transmission

Transmission Fluid Change3 specs
- Transmission Drain PlugUse new crush washer if equipped22 lb-ft30 Nm
- Transmission Filter BoltsIf equipped with bolted filter6 lb-ft8 Nm
- Transmission Pan BoltsTighten in criss-cross pattern9 lb-ft12 Nm

Exhaust

Catalytic Converter - Direct Fit4 specs
- Hanger Bolts16 lb-ft21 Nm
- Heat Shield Bolts11 lb-ft14 Nm
- Catalytic Converter Flange Bolt40.6 lb-ft55 Nm
- O2 Sensor29.5 lb-ft40 Nm
Catalytic Converter - Universal2 specs
- Catalytic Converter Flange Bolt40.6 lb-ft55 Nm
- O2 Sensor29.5 lb-ft40 Nm
Exhaust Manifold Studs1 spec
- Exhaust Manifold Stud Nut29.5 lb-ft40 Nm
Exhaust Pipe - Rear Section2 specs
- Exhaust Clamp Bolt33.2 lb-ft45 Nm
- Exhaust Flange Bolt36.9 lb-ft50 Nm
Front Pipe2 specs
- Exhaust Clamp Bolt33.2 lb-ft45 Nm
- Exhaust Flange Bolt36.9 lb-ft50 Nm
Muffler2 specs
- Hanger Bracket Bolts18 lb-ft25 Nm
- Muffler Clamps41 lb-ft55 Nm
Resonator2 specs
- Exhaust Clamp Bolt33.2 lb-ft45 Nm
- Exhaust Flange Bolt36.9 lb-ft50 Nm

Heating and A/C

AC Compressor3 specs
- AC Compressor Bolts18 lb-ft25 Nm
- AC Line FittingsUse new O-rings, add PAG oil15 lb-ft20 Nm
- Clutch Connector Bolt6 lb-ft8 Nm
AC Compressor Oil Add2 specs
- AC Compressor Bolts22.1 lb-ft30 Nm
- AC Line Fitting14.8 lb-ft20 Nm
AC Condenser2 specs
- AC Line FittingsUse new O-rings15 lb-ft20 Nm
- Condenser Mounting Bolts9 lb-ft12 Nm
AC Recharge1 spec
- Compressor Bolts26 lb-ft36 Nm

Body

Liftgate Strut2 specs
- Strut Tower Nut36.9 lb-ft50 Nm
- Wheel Lug Nut100 lb-ft135 Nm
Rear Window1 spec
- Wiper Arm Nut11.1 lb-ft15 Nm
Windshield1 spec
- Wiper Arm Nut11.1 lb-ft15 Nm
Windshield Molding1 spec
- Wiper Arm Nut11.1 lb-ft15 Nm

Torque is shown in lb-ft with Nm below it. Where a step says to turn, tighten the listed angle after the torque step before it. Use new bolts where the note says so.

Need labor times, fluids or repair steps for this car? See it on the Open Labor Project