RQUE SPECS2007 Ford Mustang torque specs
4.6L V8 3V
Change vehicle
Most looked up
- Lug nuts105 lb-ft142.4 Nm
- Oil drain plug20 lb-ft27 Nm
- Spark plugs15 lb-ft20 Nm
- Front caliper bracket bolts88 lb-ft120 Nm
- Rear caliper bracket bolts74 lb-ft100 Nm
- Front axle nut184 lb-ft250 Nm
- Outer tie rod end nut50 lb-ft68 Nm
Maintenance
AC System Diagnosis3 specs
- AC Line FittingsNew O-rings19 lb-ft25 Nm
- Connector Bolts6 lb-ft8 Nm
- Wheel Lug NutsTorque in star pattern105 lb-ft142.4 Nm
Air Filter4 specs
- Air Box Clips4 lb-ft5 Nm
- Intake Tube Clamp4 lb-ft5 Nm
- MAF Sensor Screws4 lb-ft5 Nm
- Mass Air Flow Sensor Screws2 lb-ft3 Nm
Battery Test5 specs
- Battery Hold-Down BoltDo not overtighten10 lb-ft14 Nm
- Battery Terminal BoltsClean terminals6 lb-ft8 Nm
- Connector Bolts6 lb-ft8 Nm
- Ground Cable Bolt13 lb-ft17 Nm
- Wheel Lug NutsTorque in star pattern105 lb-ft142.4 Nm
Charging System Test2 specs
- Connector Bolts6 lb-ft8 Nm
- Wheel Lug NutsTorque in star pattern105 lb-ft142.4 Nm
Check Engine Light Diagnosis2 specs
- Connector Bolts6 lb-ft8 Nm
- Wheel Lug NutsTorque in star pattern105 lb-ft142.4 Nm
Compression Test3 specs
- Air Box Clips4 lb-ft5 Nm
- Connector Bolts6 lb-ft8 Nm
- Wheel Lug NutsTorque in star pattern105 lb-ft142.4 Nm
Cooling System Pressure Test2 specs
- Connector Bolts6 lb-ft8 Nm
- Wheel Lug NutsTorque in star pattern105 lb-ft142.4 Nm
Diagnostic Scan2 specs
- Connector Bolts6 lb-ft8 Nm
- Wheel Lug NutsTorque in star pattern105 lb-ft142.4 Nm
Differential Service5 specs
- Connector Bolts6 lb-ft8 Nm
- Drain PlugNew washer38 lb-ft51 Nm
- Fill Plug38 lb-ft51 Nm
- Oil Drain PlugUse new crush washer26 lb-ft35 Nm
- Wheel Lug NutsTorque in star pattern105 lb-ft142.4 Nm
Drivability Diagnosis3 specs
- Air Box Clips4 lb-ft5 Nm
- Connector Bolts6 lb-ft8 Nm
- Wheel Lug NutsTorque in star pattern105 lb-ft142.4 Nm
Electrical Diagnosis2 specs
- Connector Bolts6 lb-ft8 Nm
- Wheel Lug NutsTorque in star pattern105 lb-ft142.4 Nm
Fluid Leak Diagnosis2 specs
- Connector Bolts6 lb-ft8 Nm
- Wheel Lug NutsTorque in star pattern105 lb-ft142.4 Nm
Leak-Down Test3 specs
- Air Box Clips4 lb-ft5 Nm
- Connector Bolts6 lb-ft8 Nm
- Wheel Lug NutsTorque in star pattern105 lb-ft142.4 Nm
Noise Diagnosis2 specs
- Connector Bolts6 lb-ft8 Nm
- Wheel Lug NutsTorque in star pattern105 lb-ft142.4 Nm
Power Steering Service5 specs
- Air Box ClipsVerify sequence with the service manual4 lb-ft5 Nm
- Connector Bolts6 lb-ft8 Nm
- Pressure Line FittingNew O-ring31 lb-ft42 Nm
- Pump Mounting Bolts25 lb-ft34 Nm
- Wheel Lug NutsTorque in star pattern. Verify sequence with the service manual105 lb-ft142.4 Nm
Tire Balance2 specs
- Connector Bolts6 lb-ft8 Nm
- Wheel Lug NutsTorque in star pattern105 lb-ft142.4 Nm
Tire Mount and Balance2 specs
- Connector Bolts6 lb-ft8 Nm
- Wheel Lug NutsTorque in star pattern105 lb-ft142.4 Nm
Tire Rotation2 specs
- Lug Nuts - Alloy WheelsTorque in star pattern, recheck after 50 miles105 lb-ft142.4 Nm
- Lug Nuts - Steel WheelsTorque in star pattern105 lb-ft142.4 Nm
TPMS Relearn2 specs
- Connector Bolts6 lb-ft8 Nm
- Wheel Lug NutsTorque in star pattern105 lb-ft142.4 Nm
TPMS Sensor2 specs
- Connector Bolts6 lb-ft8 Nm
- Wheel Lug NutsTorque in star pattern105 lb-ft142.4 Nm
Transmission Service2 specs
- Connector Bolts6 lb-ft8 Nm
- Wheel Lug NutsTorque in star pattern105 lb-ft142.4 Nm
Tune-Up - Major4 specs
- Air Box Clips4 lb-ft5 Nm
- Connector Bolts6 lb-ft8 Nm
- Oil Drain PlugUse new crush washer26 lb-ft35 Nm
- Wheel Lug NutsTorque in star pattern105 lb-ft142.4 Nm
Tune-Up - Minor4 specs
- Air Box Clips4 lb-ft5 Nm
- Connector Bolts6 lb-ft8 Nm
- Oil Drain PlugUse new crush washer26 lb-ft35 Nm
- Wheel Lug NutsTorque in star pattern105 lb-ft142.4 Nm
Wheel Alignment9 specs
- Air Box Clips4 lb-ft5 Nm
- Cam BoltsAfter adjustment114 lb-ft155 Nm
- Camber BoltsIf adjustable55 lb-ft75 Nm
- Connector Bolts6 lb-ft8 Nm
- Oil Drain PlugUse new crush washer26 lb-ft35 Nm
- Subframe BoltsIf adjusted106 lb-ft144 Nm
- Tie Rod Jam Nuts41 lb-ft55 Nm
- Tie Rod Lock NutAfter adjustment60 lb-ft81 Nm
- Wheel Lug NutsTorque in star pattern105 lb-ft142.4 Nm
Brakes
ABS Module5 specs
- ABS Module Bolts7 lb-ft10 Nm
- Bleeder Screw12 lb-ft16 Nm
- Brake Line FittingsUse flare nut wrench11 lb-ft15 Nm
- Caliper Mounting Bolts81 lb-ft110 Nm
- Wheel Lug Nuts105 lb-ft142.4 Nm
ABS Pump3 specs
- Bleeder ScrewDo not overtighten7 lb-ft10 Nm
- Caliper Mounting BoltsUse thread locker81 lb-ft110 Nm
- Wheel Lug NutsTorque in star pattern105 lb-ft142.4 Nm
ABS Tone Ring4 specs
- Caliper Bracket Bolts - FrontThreadlocker recommended88 lb-ft120 Nm
- Caliper Mounting Bolts81 lb-ft110 Nm
- Caliper Slide Pin BoltsApply silicone brake grease26 lb-ft35 Nm
- Wheel Lug NutsTorque in star pattern105 lb-ft142.4 Nm
ABS Wheel Speed Sensor - Front5 specs
- ABS Sensor BoltDo not overtighten7 lb-ft10 Nm
- Bleeder Screw12 lb-ft16 Nm
- Caliper Mounting Bolts81 lb-ft110 Nm
- Wheel Bearing Hub Bolts81 lb-ft110 Nm
- Wheel Lug NutsTorque in star pattern100 lb-ft136 Nm
ABS Wheel Speed Sensor - Rear4 specs
- ABS Sensor BoltDo not overtighten7 lb-ft10 Nm
- Bleeder Screw12 lb-ft16 Nm
- Caliper Mounting Bolts81 lb-ft110 Nm
- Wheel Lug Nuts100 lb-ft136 Nm
Brake Bleed - All Four3 specs
- Bleeder ScrewDo not overtighten. Verify sequence with the service manual7 lb-ft10 Nm
- Caliper Mounting Bolts81 lb-ft110 Nm
- Wheel Lug NutsTorque in star pattern. Verify sequence with the service manual105 lb-ft142.4 Nm
Brake Booster6 specs
- Bleeder Screw12 lb-ft16 Nm
- Brake Booster NutsVerify sequence with the service manual18 lb-ft25 Nm
- Brake Pedal Pushrod LockVerify sequence with the service manual11 lb-ft15 Nm
- Caliper Mounting Bolts81 lb-ft110 Nm
- Master Cylinder NutsVerify sequence with the service manual18 lb-ft25 Nm
- Wheel Lug Nuts100 lb-ft136 Nm
Brake Booster Check Valve2 specs
- Caliper Mounting Bolts81 lb-ft110 Nm
- Wheel Lug NutsTorque in star pattern. Verify sequence with the service manual105 lb-ft142.4 Nm
Brake Caliper - Front3 specs
- Bleeder ScrewDo not overtighten7 lb-ft10 Nm
- Brake Line Banjo BoltUse new copper washers18 lb-ft25 Nm
- Caliper Bracket BoltsThreadlocker recommended88 lb-ft120 Nm
Brake Caliper - Rear3 specs
- Bleeder ScrewDo not overtighten7 lb-ft10 Nm
- Brake Line Banjo BoltUse new copper washers18 lb-ft25 Nm
- Caliper Bracket BoltsThreadlocker recommended74 lb-ft100 Nm
Brake Caliper Bracket6 specs
- Bleeder ScrewDo not overtighten. Verify sequence with the service manual7 lb-ft10 Nm
- Brake Hose Banjo BoltNew copper washers38 lb-ft51 Nm
- Caliper Bracket Bolts - FrontThreadlocker recommended. Verify sequence with the service manual88 lb-ft120 Nm
- Caliper Mounting BoltsUse thread locker81 lb-ft110 Nm
- Caliper Slide Pin BoltsApply silicone brake grease. Verify sequence with the service manual26 lb-ft35 Nm
- Wheel Lug NutsTorque in star pattern. Verify sequence with the service manual105 lb-ft142.4 Nm
Brake Caliper Rebuild - Front5 specs
- Bleeder ScrewDo not overtighten7 lb-ft10 Nm
- Caliper Bracket Bolts - FrontThreadlocker recommended88 lb-ft120 Nm
- Caliper Mounting BoltsUse thread locker81 lb-ft110 Nm
- Caliper Slide Pin BoltsApply silicone brake grease26 lb-ft35 Nm
- Wheel Lug NutsTorque in star pattern105 lb-ft142.4 Nm
Brake Caliper Rebuild - Rear4 specs
- Bleeder ScrewDo not overtighten7 lb-ft10 Nm
- Caliper Mounting Bolts81 lb-ft110 Nm
- Caliper Slide Pin BoltsApply silicone brake grease26 lb-ft35 Nm
- Wheel Lug NutsTorque in star pattern105 lb-ft142.4 Nm
Brake Caliper Slide Pins4 specs
- Caliper Bracket Bolts - FrontThreadlocker recommended88 lb-ft120 Nm
- Caliper Mounting BoltsUse thread locker81 lb-ft110 Nm
- Caliper Slide Pin BoltsApply silicone brake grease26 lb-ft35 Nm
- Wheel Lug NutsTorque in star pattern105 lb-ft142.4 Nm
Brake Drum - Rear2 specs
- Caliper Mounting Bolts81 lb-ft110 Nm
- Wheel Lug NutsTorque in star pattern. Verify sequence with the service manual105 lb-ft142.4 Nm
Brake Fluid Flush7 specs
- Air Box ClipsVerify sequence with the service manual4 lb-ft5 Nm
- Bleeder ScrewDo not overtighten. Verify sequence with the service manual7 lb-ft10 Nm
- Caliper Mounting Bolts81 lb-ft110 Nm
- Connector Bolts6 lb-ft8 Nm
- Master Cylinder CapHand tight4 lb-ft5 Nm
- Oil Drain PlugUse new crush washer. Verify sequence with the service manual26 lb-ft35 Nm
- Wheel Lug NutsTorque in star pattern. Verify sequence with the service manual105 lb-ft142.4 Nm
Brake Hose - Front5 specs
- Bleeder Screw12 lb-ft16 Nm
- Brake Hose Banjo BoltUse new copper washers. Verify sequence with the service manual18 lb-ft25 Nm
- Brake Hose BracketVerify sequence with the service manual7 lb-ft10 Nm
- Caliper Mounting BoltsUse thread locker81 lb-ft110 Nm
- Wheel Lug Nuts100 lb-ft136 Nm
Brake Hose - Rear5 specs
- Bleeder Screw12 lb-ft16 Nm
- Brake Hose Banjo BoltUse new copper washers. Verify sequence with the service manual18 lb-ft25 Nm
- Brake Hose BracketVerify sequence with the service manual7 lb-ft10 Nm
- Caliper Mounting Bolts81 lb-ft110 Nm
- Wheel Lug Nuts100 lb-ft136 Nm
Brake Light Switch2 specs
- Caliper Mounting BoltsUse thread locker81 lb-ft110 Nm
- Wheel Lug NutsTorque in star pattern. Verify sequence with the service manual105 lb-ft142.4 Nm
Brake Line - Single3 specs
- Bleeder ScrewDo not overtighten. Verify sequence with the service manual7 lb-ft10 Nm
- Caliper Mounting Bolts81 lb-ft110 Nm
- Wheel Lug NutsTorque in star pattern. Verify sequence with the service manual105 lb-ft142.4 Nm
Brake Lines - Complete Set3 specs
- Bleeder ScrewDo not overtighten. Verify sequence with the service manual7 lb-ft10 Nm
- Caliper Mounting BoltsUse thread locker81 lb-ft110 Nm
- Wheel Lug NutsTorque in star pattern. Verify sequence with the service manual105 lb-ft142.4 Nm
Brake Master Cylinder2 specs
- Brake Line FittingsUse flare nut wrench11 lb-ft15 Nm
- Master Cylinder Nuts18 lb-ft25 Nm
Brake Master Cylinder Rebuild3 specs
- Brake Line FittingsUse flare nut wrench11 lb-ft15 Nm
- Master Cylinder Mounting Nuts18 lb-ft25 Nm
- Reservoir Mounting Bolts6 lb-ft8 Nm
Brake Pads - Front3 specs
- Caliper Bracket BoltsThreadlocker recommended88 lb-ft120 Nm
- Caliper Slide Pin BoltsApply silicone brake grease26 lb-ft35 Nm
- Wheel Lug NutsTorque in star pattern105 lb-ft142.4 Nm
Brake Pads - Rear3 specs
- Caliper Bracket BoltsThreadlocker recommended74 lb-ft100 Nm
- Caliper Slide Pin BoltsApply silicone brake grease22 lb-ft30 Nm
- Wheel Lug NutsTorque in star pattern105 lb-ft142.4 Nm
Brake Pads and Rotors - Front7 specs
- Bleeder ScrewDo not overtighten. Verify sequence with the service manual7 lb-ft10 Nm
- Caliper Bracket BoltsUse thread locker94 lb-ft127 Nm
- Caliper Bracket Bolts - FrontThreadlocker recommended. Verify sequence with the service manual88 lb-ft120 Nm
- Caliper Mounting BoltsUse thread locker81 lb-ft110 Nm
- Caliper Slide BoltsLubricate pins31 lb-ft42 Nm
- Caliper Slide Pin BoltsApply silicone brake grease. Verify sequence with the service manual26 lb-ft35 Nm
- Wheel Lug NutsTorque in star pattern. Verify sequence with the service manual105 lb-ft142.4 Nm
Brake Pads and Rotors - Rear6 specs
- Bleeder ScrewDo not overtighten. Verify sequence with the service manual7 lb-ft10 Nm
- Caliper Bracket BoltsUse thread locker94 lb-ft127 Nm
- Caliper Mounting Bolts81 lb-ft110 Nm
- Caliper Slide BoltsLubricate pins31 lb-ft42 Nm
- Caliper Slide Pin BoltsApply silicone brake grease. Verify sequence with the service manual26 lb-ft35 Nm
- Wheel Lug NutsTorque in star pattern. Verify sequence with the service manual105 lb-ft142.4 Nm
Brake Proportioning Valve5 specs
- Bleeder Screw12 lb-ft16 Nm
- Brake Line FittingsUse flare nut wrench. Verify sequence with the service manual11 lb-ft15 Nm
- Caliper Mounting BoltsUse thread locker81 lb-ft110 Nm
- Proportioning Valve BoltsVerify sequence with the service manual11 lb-ft15 Nm
- Wheel Lug NutsTorque in star pattern100 lb-ft136 Nm
Brake Rotor - Front Single7 specs
- Brake Rotor Set Screw6 lb-ft8 Nm
- Caliper Bracket Bolts94 lb-ft127 Nm
- Caliper Bracket Bolts - FrontThreadlocker recommended. Verify sequence with the service manual88 lb-ft120 Nm
- Caliper Mounting Bolts81 lb-ft110 Nm
- Caliper Slide Pin BoltsApply silicone brake grease. Verify sequence with the service manual26 lb-ft35 Nm
- Hub NutIf removed225 lb-ft305 Nm
- Wheel Lug NutsTorque in star pattern. Verify sequence with the service manual105 lb-ft142.4 Nm
Brake Rotor - Rear Single5 specs
- Brake Rotor Set Screw6 lb-ft8 Nm
- Caliper Bracket Bolts94 lb-ft127 Nm
- Caliper Mounting Bolts81 lb-ft110 Nm
- Caliper Slide Pin BoltsApply silicone brake grease. Verify sequence with the service manual26 lb-ft35 Nm
- Wheel Lug NutsTorque in star pattern. Verify sequence with the service manual105 lb-ft142.4 Nm
Brake Rotors - Front Pair7 specs
- Brake Rotor Set Screw6 lb-ft8 Nm
- Caliper Bracket Bolts94 lb-ft127 Nm
- Caliper Bracket Bolts - FrontThreadlocker recommended. Verify sequence with the service manual88 lb-ft120 Nm
- Caliper Mounting BoltsUse thread locker81 lb-ft110 Nm
- Caliper Slide Pin BoltsApply silicone brake grease. Verify sequence with the service manual26 lb-ft35 Nm
- Hub NutIf removed225 lb-ft305 Nm
- Wheel Lug NutsTorque in star pattern. Verify sequence with the service manual105 lb-ft142.4 Nm
Brake Rotors - Rear Pair5 specs
- Brake Rotor Set Screw6 lb-ft8 Nm
- Caliper Bracket Bolts94 lb-ft127 Nm
- Caliper Mounting Bolts81 lb-ft110 Nm
- Caliper Slide Pin BoltsApply silicone brake grease. Verify sequence with the service manual26 lb-ft35 Nm
- Wheel Lug NutsTorque in star pattern. Verify sequence with the service manual105 lb-ft142.4 Nm
Drum Brake Hardware Kit2 specs
- Caliper Mounting BoltsUse thread locker81 lb-ft110 Nm
- Wheel Lug NutsTorque in star pattern. Verify sequence with the service manual105 lb-ft142.4 Nm
Drum Brake Shoes - Rear2 specs
- Caliper Mounting BoltsUse thread locker81 lb-ft110 Nm
- Wheel Lug NutsTorque in star pattern. Verify sequence with the service manual105 lb-ft142.4 Nm
Electronic Parking Brake Motor3 specs
- Caliper Mounting Bolts81 lb-ft110 Nm
- Caliper Slide Pin BoltsApply silicone brake grease. Verify sequence with the service manual26 lb-ft35 Nm
- Wheel Lug NutsTorque in star pattern. Verify sequence with the service manual105 lb-ft142.4 Nm
Front Brake Pad Replacement3 specs
- Caliper Bracket BoltsThreadlocker recommended88 lb-ft120 Nm
- Caliper Slide Pin BoltsApply silicone brake grease26 lb-ft35 Nm
- Wheel Lug NutsTorque in star pattern105 lb-ft142.4 Nm
Parking Brake Actuator3 specs
- Caliper Mounting Bolts81 lb-ft110 Nm
- Caliper Slide Pin BoltsApply silicone brake grease. Verify sequence with the service manual26 lb-ft35 Nm
- Wheel Lug NutsTorque in star pattern. Verify sequence with the service manual105 lb-ft142.4 Nm
Parking Brake Cable5 specs
- Bleeder Screw12 lb-ft16 Nm
- Cable Bracket BoltsVerify sequence with the service manual9 lb-ft12 Nm
- Caliper Mounting Bolts81 lb-ft110 Nm
- Equalizer NutAdjust for proper tension. Verify sequence with the service manual11 lb-ft15 Nm
- Wheel Lug NutsTorque in star pattern100 lb-ft136 Nm
Parking Brake Shoes5 specs
- Adjuster LockVerify sequence with the service manual4 lb-ft5 Nm
- Bleeder Screw12 lb-ft16 Nm
- Caliper Mounting BoltsUse thread locker81 lb-ft110 Nm
- Hold-Down SpringsVerify sequence with the service manual6 lb-ft8 Nm
- Wheel Lug NutsTorque in star pattern. Verify sequence with the service manual105 lb-ft142.4 Nm
Rear Brake Shoe Replacement3 specs
- Backing Plate Bolts44 lb-ft60 Nm
- Wheel Cylinder Bolts9 lb-ft12 Nm
- Wheel Lug NutsTorque in star pattern105 lb-ft142.4 Nm
Wheel Cylinder3 specs
- Bleeder ScrewDo not overtighten7 lb-ft10 Nm
- Caliper Mounting Bolts81 lb-ft110 Nm
- Wheel Lug NutsTorque in star pattern105 lb-ft142.4 Nm
Engine
Camshaft Position Sensor5 specs
- Camshaft Position Sensor7 lb-ft10 Nm
- Electrical Connector Bolts6 lb-ft8 Nm
- Gasket Surface BoltsClean mating surfaces19 lb-ft26 Nm
- Sensor Mounting Bolts10 lb-ft14 Nm
- Valve Cover BoltsTighten in sequence7 lb-ft10 Nm
Camshaft R&R20 specs
- Cam Phaser BoltApply threadlocker, hold cam stationary48 lb-ft65 Nm
- Camshaft Bearing Cap BoltsTighten in sequence, 3 passes10 lb-ft14 Nm
- Camshaft Cap BoltsTighten in sequence from center outward, multiple passes10 lb-ft14 Nm
- Camshaft Position Sensor7 lb-ft10 Nm
- Camshaft Sprocket BoltsHold cam with wrench on hex59 lb-ft80 Nm
- Crankshaft Position Sensor7 lb-ft10 Nm
- Crankshaft Pulley BoltOften TTY, may need impact133 lb-ft180 Nm
- Electrical Connector Bolts6 lb-ft8 Nm
- Gasket Surface BoltsClean mating surfaces19 lb-ft26 Nm
- Oil Drain PlugUse new crush washer26 lb-ft35 Nm
- Rocker Arm BoltsTighten with cam lobe pointing away22 lb-ft30 Nm
- Rocker Arm Shaft BoltsTighten evenly in sequence18 lb-ft25 Nm
- Sensor Mounting Bolts10 lb-ft14 Nm
- Timing Chain Guide BoltsReplace if worn9 lb-ft12 Nm
- Timing Chain Idler Sprocket18 lb-ft25 Nm
- Timing Chain Tensioner BoltInstall with pin/clip to compress18 lb-ft25 Nm
- Timing Cover Bolts - 10mmTighten in sequence33 lb-ft45 Nm
- Timing Cover Bolts - 8mmTighten in sequence18 lb-ft25 Nm
- Valve Cover BoltsTighten in sequence7 lb-ft10 Nm
- VVT Solenoid Bolt7 lb-ft10 Nm
Connecting Rod Bearings6 specs
- Connecting Rod BoltsTTY - critical torque plus angle33 lb-ft45 Nm
- Electrical Connector Bolts6 lb-ft8 Nm
- Gasket Surface BoltsClean mating surfaces19 lb-ft26 Nm
- Oil Drain PlugUse new crush washer26 lb-ft35 Nm
- Oil Pan BoltTighten in sequence9 lb-ft12 Nm
- Sensor Mounting Bolts10 lb-ft14 Nm
Crankshaft Position Sensor4 specs
- Crankshaft Position Sensor7 lb-ft10 Nm
- Electrical Connector Bolts6 lb-ft8 Nm
- Gasket Surface BoltsClean mating surfaces19 lb-ft26 Nm
- Sensor Mounting Bolts10 lb-ft14 Nm
Crankshaft R&R20 specs
- Connecting Rod BoltsTTY - critical torque plus angle33 lb-ft45 Nm
- Crankshaft Pulley BoltOften TTY - check spec, may require impact133 lb-ft180 Nm
- Cylinder Head BoltsTTY - tighten in sequence plus angle48 lb-ft65 Nm
- Electrical Connector Bolts6 lb-ft8 Nm
- Flexplate BoltsAutomatic transmissions63 lb-ft85 Nm
- Flywheel BoltsOften TTY, tighten in star pattern70 lb-ft95 Nm
- Front Main Seal Housing9 lb-ft12 Nm
- Gasket Surface BoltsClean mating surfaces19 lb-ft26 Nm
- Main Bearing Cap BoltsTTY - tighten in sequence plus angle55 lb-ft75 Nm
- Oil Drain PlugUse new crush washer26 lb-ft35 Nm
- Oil Pan BoltTighten in sequence9 lb-ft12 Nm
- Oil Pump Bolts9 lb-ft12 Nm
- Oil Pump Pickup Tube9 lb-ft12 Nm
- Rear Main Seal Housing9 lb-ft12 Nm
- Sensor Mounting Bolts10 lb-ft14 Nm
- Timing Chain Guide BoltsReplace if worn9 lb-ft12 Nm
- Timing Chain Tensioner BoltInstall with pin/clip to compress18 lb-ft25 Nm
- Timing Cover Bolts - 10mmTighten in sequence33 lb-ft45 Nm
- Timing Cover Bolts - 8mmTighten in sequence18 lb-ft25 Nm
- Transmission-to-Engine Bolts41 lb-ft55 Nm
Cylinder Head R&R17 specs
- Camshaft Bearing Cap BoltsTighten in sequence, 3 passes10 lb-ft14 Nm
- Camshaft Cap BoltsTighten in sequence from center outward, multiple passes10 lb-ft14 Nm
- Camshaft Sprocket BoltsHold cam with wrench on hex59 lb-ft80 Nm
- Cylinder Head BoltsTTY - tighten in sequence plus angle48 lb-ft65 Nm
- Electrical Connector Bolts6 lb-ft8 Nm
- Exhaust Manifold NutsApply anti-seize, work hot-to-cold22 lb-ft30 Nm
- Gasket Surface BoltsClean mating surfaces19 lb-ft26 Nm
- Intake Manifold Bolt18 lb-ft25 Nm
- Oil Drain PlugUse new crush washer26 lb-ft35 Nm
- Rocker Arm BoltsTighten with cam lobe pointing away22 lb-ft30 Nm
- Rocker Arm Shaft BoltsTighten evenly in sequence18 lb-ft25 Nm
- Sensor Mounting Bolts10 lb-ft14 Nm
- Thermostat Housing Bolt11 lb-ft15 Nm
- Timing Chain Guide BoltsReplace if worn9 lb-ft12 Nm
- Timing Chain Tensioner BoltInstall with pin/clip to compress18 lb-ft25 Nm
- Timing Cover Bolts - 8mmTighten in sequence18 lb-ft25 Nm
- Valve Cover BoltsTighten in sequence7 lb-ft10 Nm
Cylinder Head Resurface7 specs
- Cylinder Head BoltsTTY - tighten in sequence plus angle48 lb-ft65 Nm
- Electrical Connector Bolts6 lb-ft8 Nm
- Exhaust Manifold NutsApply anti-seize, work hot-to-cold22 lb-ft30 Nm
- Gasket Surface BoltsClean mating surfaces19 lb-ft26 Nm
- Intake Manifold Bolt18 lb-ft25 Nm
- Sensor Mounting Bolts10 lb-ft14 Nm
- Valve Cover BoltsTighten in sequence7 lb-ft10 Nm
Engine Mount - Front3 specs
- Engine Mount Through-Bolt63 lb-ft85 Nm
- Engine Mount-to-Block Bolts48 lb-ft65 Nm
- Engine Mount-to-Frame Bolts55 lb-ft75 Nm
Engine Mount - Rear6 specs
- Electrical Connector Bolts6 lb-ft8 Nm
- Engine Mount Through-Bolt81 lb-ft110 Nm
- Engine Mount-to-Block Bolts48 lb-ft65 Nm
- Engine Mount-to-Frame Bolts55 lb-ft75 Nm
- Gasket Surface BoltsClean mating surfaces19 lb-ft26 Nm
- Sensor Mounting Bolts10 lb-ft14 Nm
Engine Mounts - All7 specs
- Electrical Connector Bolts6 lb-ft8 Nm
- Engine Mount Through-Bolt63 lb-ft85 Nm
- Engine Mount-to-Block Bolts48 lb-ft65 Nm
- Engine Mount-to-Frame Bolts55 lb-ft75 Nm
- Gasket Surface BoltsClean mating surfaces19 lb-ft26 Nm
- Sensor Mounting Bolts10 lb-ft14 Nm
- Transmission Mount Bolts48 lb-ft65 Nm
Engine R&R13 specs
- AC Compressor Bolts18 lb-ft25 Nm
- Alternator Mounting Bolts37 lb-ft50 Nm
- Electrical Connector Bolts6 lb-ft8 Nm
- Engine Mount-to-Block Bolts48 lb-ft65 Nm
- Engine Mount-to-Frame Bolts55 lb-ft75 Nm
- Exhaust Manifold NutsApply anti-seize, work hot-to-cold22 lb-ft30 Nm
- Flywheel BoltsOften TTY, tighten in star pattern70 lb-ft95 Nm
- Gasket Surface BoltsClean mating surfaces19 lb-ft26 Nm
- Oil Drain PlugUse new crush washer26 lb-ft35 Nm
- Power Steering Pump Bolts18 lb-ft25 Nm
- Sensor Mounting Bolts10 lb-ft14 Nm
- Starter Mounting Bolt37 lb-ft50 Nm
- Transmission-to-Engine Bolts41 lb-ft55 Nm
Engine Rebuild21 specs
- Balance Shaft Bolts18 lb-ft25 Nm
- Camshaft Bearing Cap BoltsTighten in sequence, 3 passes10 lb-ft14 Nm
- Camshaft Cap BoltsTighten in sequence from center outward, multiple passes10 lb-ft14 Nm
- Connecting Rod BoltsTTY - critical torque plus angle33 lb-ft45 Nm
- Crankshaft Pulley BoltOften TTY - check spec, may require impact133 lb-ft180 Nm
- Cylinder Head BoltsTTY - tighten in sequence plus angle48 lb-ft65 Nm
- Electrical Connector Bolts6 lb-ft8 Nm
- Exhaust Manifold NutsApply anti-seize, work hot-to-cold22 lb-ft30 Nm
- Flywheel BoltsOften TTY, tighten in star pattern70 lb-ft95 Nm
- Gasket Surface BoltsClean mating surfaces19 lb-ft26 Nm
- Intake Manifold Bolt18 lb-ft25 Nm
- Main Bearing Cap BoltsTTY - tighten in sequence plus angle55 lb-ft75 Nm
- Oil Drain PlugUse new crush washer26 lb-ft35 Nm
- Oil Pan BoltTighten in sequence9 lb-ft12 Nm
- Oil Pump Bolts9 lb-ft12 Nm
- Oil Pump Pickup Tube9 lb-ft12 Nm
- Sensor Mounting Bolts10 lb-ft14 Nm
- Timing Chain Guide BoltsReplace if worn9 lb-ft12 Nm
- Timing Chain Tensioner BoltInstall with pin/clip to compress18 lb-ft25 Nm
- Timing Cover Bolts - 8mmTighten in sequence18 lb-ft25 Nm
- Valve Cover BoltsTighten in sequence7 lb-ft10 Nm
Exhaust Manifold8 specs
- Electrical Connector Bolts6 lb-ft8 Nm
- Exhaust Flange BoltApply anti-seize. Verify sequence with the service manual33 lb-ft45 Nm
- Exhaust Manifold NutsApply anti-seize, work hot-to-cold. Verify sequence with the service manual22 lb-ft30 Nm
- Gasket Surface BoltsClean mating surfaces19 lb-ft26 Nm
- Hanger Bolts19 lb-ft25 Nm
- Heat Shield BoltsVerify sequence with the service manual7 lb-ft10 Nm
- O2 SensorAnti-seize threads44 lb-ft59 Nm
- Sensor Mounting Bolts10 lb-ft14 Nm
Exhaust Manifold Gasket3 specs
- Exhaust Manifold NutsApply anti-seize, work hot-to-cold22 lb-ft30 Nm
- Exhaust Manifold StudsIf replacing studs11 lb-ft15 Nm
- Heat Shield Bolts7 lb-ft10 Nm
Fan Belt Replacement3 specs
- Idler Pulley Bolt30 lb-ft40 Nm
- Tensioner Bolt18 lb-ft25 Nm
- Tensioner Pulley Bolt33 lb-ft45 Nm
Flexplate6 specs
- Electrical Connector Bolts6 lb-ft8 Nm
- Flexplate BoltsAutomatic transmissions. Verify sequence with the service manual63 lb-ft85 Nm
- Gasket Surface BoltsClean mating surfaces19 lb-ft26 Nm
- Sensor Mounting Bolts10 lb-ft14 Nm
- Torque Converter BoltsVerify sequence with the service manual37 lb-ft50 Nm
- Transmission-to-Engine BoltsVerify sequence with the service manual41 lb-ft55 Nm
Flywheel6 specs
- Drain PlugUse new washer31 lb-ft42 Nm
- Fill Plug31 lb-ft42 Nm
- Flexplate BoltsAutomatic transmissions63 lb-ft85 Nm
- Flywheel BoltsOften TTY - check specs, tighten in star pattern70 lb-ft95 Nm
- Transmission Drain PlugUse new crush washer if equipped22 lb-ft30 Nm
- Transmission Pan BoltsTighten in criss-cross pattern9 lb-ft12 Nm
Freeze Plug - Single4 specs
- Electrical Connector Bolts6 lb-ft8 Nm
- Freeze PlugUse sealant on edges7 lb-ft10 Nm
- Gasket Surface BoltsClean mating surfaces19 lb-ft26 Nm
- Sensor Mounting Bolts10 lb-ft14 Nm
Freeze Plugs - All4 specs
- Electrical Connector Bolts6 lb-ft8 Nm
- Freeze PlugUse sealant on edges7 lb-ft10 Nm
- Gasket Surface BoltsClean mating surfaces19 lb-ft26 Nm
- Sensor Mounting Bolts10 lb-ft14 Nm
Front Main Seal8 specs
- Crankshaft Pulley BoltOften TTY, may need impact133 lb-ft180 Nm
- Electrical Connector Bolts6 lb-ft8 Nm
- Gasket Surface BoltsClean mating surfaces19 lb-ft26 Nm
- Oil Drain PlugUse new crush washer26 lb-ft35 Nm
- Oil Pan BoltFront section only9 lb-ft12 Nm
- Sensor Mounting Bolts10 lb-ft14 Nm
- Timing Cover Bolts - 10mmTighten in sequence33 lb-ft45 Nm
- Timing Cover Bolts - 8mmTighten in sequence18 lb-ft25 Nm
Full Engine Tune-Up4 specs
- Ignition Coil Bolt6 lb-ft8 Nm
- Spark Plugs - Aluminum HeadApply anti-seize to threads15 lb-ft20 Nm
- Throttle Body Bolts7 lb-ft10 Nm
- Valve Cover BoltsTighten in sequence7 lb-ft10 Nm
Harmonic Balancer4 specs
- Crankshaft Pulley BoltOften TTY, may need impact. Verify sequence with the service manual133 lb-ft180 Nm
- Electrical Connector Bolts6 lb-ft8 Nm
- Gasket Surface BoltsClean mating surfaces19 lb-ft26 Nm
- Sensor Mounting Bolts10 lb-ft14 Nm
Head Gasket - Single6 specs
- Exhaust Manifold NutsApply anti-seize18 lb-ft25 Nm
- Intake Manifold BoltTighten in sequence18 lb-ft25 Nm
- Cylinder Head Bolts - Step 1Always use new TTY bolts30 lb-ft40 Nm
- Cylinder Head Bolts - Step 2Tighten in sequence59 lb-ft80 Nm
- Cylinder Head Bolts - Step 3Plus 90 degreesTurn 90°
- Cylinder Head Bolts - Step 4Plus 90 degreesTurn 90°
Head Gaskets - Both15 specs
- Camshaft Cap BoltsTighten in sequence from center outward, multiple passes10 lb-ft14 Nm
- Camshaft Sprocket BoltsHold cam with wrench on hex59 lb-ft80 Nm
- Crankshaft Pulley BoltOften TTY - check spec, may require impact133 lb-ft180 Nm
- Cylinder Head BoltsMulti-step + angle81 lb-ft110 Nm
- Electrical Connector Bolts6 lb-ft8 Nm
- Exhaust Manifold Nuts31 lb-ft42 Nm
- Gasket Surface BoltsClean mating surfaces19 lb-ft26 Nm
- Intake Manifold Bolt23 lb-ft31 Nm
- Oil Drain PlugUse new crush washer26 lb-ft35 Nm
- Rocker Arm BoltsTighten with cam lobe pointing away22 lb-ft30 Nm
- Sensor Mounting Bolts7 lb-ft10 Nm
- Timing Chain Tensioner BoltInstall with pin/clip to compress18 lb-ft25 Nm
- Timing Cover Bolts - 8mmTighten in sequence18 lb-ft25 Nm
- Valve Cover BoltsTighten in sequence7 lb-ft10 Nm
- VVT Solenoid Bolt7 lb-ft10 Nm
Idle Air Control Valve4 specs
- Electrical Connector Bolts6 lb-ft8 Nm
- Gasket Surface BoltsClean mating surfaces19 lb-ft26 Nm
- IAC Valve Screws2 lb-ft3 Nm
- Sensor Mounting Bolts10 lb-ft14 Nm
Idler Pulley4 specs
- Electrical Connector Bolts6 lb-ft8 Nm
- Gasket Surface BoltsClean mating surfaces19 lb-ft26 Nm
- Idler Pulley Bolt33 lb-ft45 Nm
- Sensor Mounting Bolts10 lb-ft14 Nm
Intake Manifold7 specs
- Electrical Connector Bolts6 lb-ft8 Nm
- Fuel Rail BoltsVerify sequence with the service manual9 lb-ft12 Nm
- Gasket Surface BoltsClean mating surfaces19 lb-ft26 Nm
- Intake Manifold BoltTighten in sequence from center out. Verify sequence with the service manual18 lb-ft25 Nm
- PCV ValveVerify sequence with the service manual6 lb-ft8 Nm
- Sensor Mounting Bolts10 lb-ft14 Nm
- Throttle Body BoltsVerify sequence with the service manual7 lb-ft10 Nm
Intake Manifold Gasket3 specs
- Fuel Rail Bolts9 lb-ft12 Nm
- Intake Manifold BoltTighten in sequence from center out18 lb-ft25 Nm
- Throttle Body Bolts7 lb-ft10 Nm
Knock Sensor4 specs
- Electrical Connector Bolts6 lb-ft8 Nm
- Gasket Surface BoltsClean mating surfaces19 lb-ft26 Nm
- Knock SensorTorque critical for function15 lb-ft20 Nm
- Sensor Mounting Bolts10 lb-ft14 Nm
Lifter - Single7 specs
- Electrical Connector Bolts6 lb-ft8 Nm
- Gasket Surface BoltsClean mating surfaces19 lb-ft26 Nm
- Intake Manifold Bolt18 lb-ft25 Nm
- Rocker Arm BoltsTighten with cam lobe pointing away22 lb-ft30 Nm
- Rocker Arm Shaft BoltsTighten evenly in sequence18 lb-ft25 Nm
- Sensor Mounting Bolts10 lb-ft14 Nm
- Valve Cover BoltsTighten in sequence7 lb-ft10 Nm
Lifters/Tappets - All10 specs
- Camshaft Bearing Cap BoltsTighten in sequence, 3 passes10 lb-ft14 Nm
- Camshaft Cap BoltsTighten in sequence from center outward, multiple passes10 lb-ft14 Nm
- Camshaft Position Sensor7 lb-ft10 Nm
- Electrical Connector Bolts6 lb-ft8 Nm
- Gasket Surface BoltsClean mating surfaces19 lb-ft26 Nm
- Intake Manifold Bolt18 lb-ft25 Nm
- Rocker Arm BoltsTighten with cam lobe pointing away22 lb-ft30 Nm
- Rocker Arm Shaft BoltsTighten evenly in sequence18 lb-ft25 Nm
- Sensor Mounting Bolts10 lb-ft14 Nm
- Valve Cover BoltsTighten in sequence7 lb-ft10 Nm
Long Block Replacement16 specs
- Camshaft Cap BoltsTighten in sequence from center outward, multiple passes10 lb-ft14 Nm
- Connecting Rod BoltsTTY - critical torque plus angle33 lb-ft45 Nm
- Cylinder Head BoltsTTY - tighten in sequence plus angle48 lb-ft65 Nm
- Electrical Connector Bolts6 lb-ft8 Nm
- Exhaust Manifold NutsApply anti-seize, work hot-to-cold22 lb-ft30 Nm
- Flywheel BoltsOften TTY, tighten in star pattern70 lb-ft95 Nm
- Gasket Surface BoltsClean mating surfaces19 lb-ft26 Nm
- Intake Manifold Bolt18 lb-ft25 Nm
- Main Bearing Cap BoltsTTY - tighten in sequence plus angle55 lb-ft75 Nm
- Oil Drain PlugUse new crush washer26 lb-ft35 Nm
- Oil Pan Bolt9 lb-ft12 Nm
- Sensor Mounting Bolts10 lb-ft14 Nm
- Timing Chain Tensioner BoltInstall with pin/clip to compress18 lb-ft25 Nm
- Timing Cover Bolts - 8mmTighten in sequence18 lb-ft25 Nm
- Transmission-to-Engine Bolts41 lb-ft55 Nm
- Valve Cover BoltsTighten in sequence7 lb-ft10 Nm
Main Bearings9 specs
- Electrical Connector Bolts6 lb-ft8 Nm
- Flywheel BoltsOften TTY, tighten in star pattern. Verify sequence with the service manual70 lb-ft95 Nm
- Gasket Surface BoltsClean mating surfaces19 lb-ft26 Nm
- Main Bearing Cap BoltsTTY - tighten in sequence plus angle. Verify sequence with the service manual55 lb-ft75 Nm
- Oil Drain PlugUse new crush washer. Verify sequence with the service manual26 lb-ft35 Nm
- Oil Pan BoltTighten in sequence. Verify sequence with the service manual9 lb-ft12 Nm
- Oil Pump Pickup TubeVerify sequence with the service manual9 lb-ft12 Nm
- Sensor Mounting Bolts10 lb-ft14 Nm
- Transmission-to-Engine BoltsVerify sequence with the service manual41 lb-ft55 Nm
Manifold Absolute Pressure Sensor4 specs
- Electrical Connector Bolts6 lb-ft8 Nm
- Gasket Surface BoltsClean mating surfaces19 lb-ft26 Nm
- MAP Sensor Screws2 lb-ft3 Nm
- Sensor Mounting Bolts10 lb-ft14 Nm
Mass Air Flow Sensor5 specs
- Air Intake Clamps2 lb-ft3 Nm
- Electrical Connector Bolts6 lb-ft8 Nm
- Gasket Surface BoltsClean mating surfaces19 lb-ft26 Nm
- MAF Sensor Screws2 lb-ft3 Nm
- Sensor Mounting Bolts10 lb-ft14 Nm
Oil Change2 specs
- Oil Drain PlugUse new crush washer20 lb-ft27 Nm
- Oil Filter (Spin-On)Hand tight plus 3/4 turn15 lb-ft20 Nm
Oil Level Sensor5 specs
- Electrical Connector Bolts6 lb-ft8 Nm
- Gasket Surface BoltsClean mating surfaces19 lb-ft26 Nm
- Oil Level Sensor11 lb-ft15 Nm
- Oil Pan BoltIf access needed9 lb-ft12 Nm
- Sensor Mounting Bolts10 lb-ft14 Nm
Oil Pan Gasket2 specs
- Oil Drain PlugUse new crush washer26 lb-ft35 Nm
- Oil Pan BoltTighten in sequence from center outward9 lb-ft12 Nm
Oil Pan Replacement6 specs
- Electrical Connector Bolts6 lb-ft8 Nm
- Gasket Surface BoltsClean mating surfaces19 lb-ft26 Nm
- Oil Drain PlugUse new crush washer26 lb-ft35 Nm
- Oil Pan BoltTighten in sequence9 lb-ft12 Nm
- Oil Pump Pickup Tube9 lb-ft12 Nm
- Sensor Mounting Bolts10 lb-ft14 Nm
Oil Pressure Sensor4 specs
- Electrical Connector Bolts6 lb-ft8 Nm
- Gasket Surface BoltsClean mating surfaces19 lb-ft26 Nm
- Oil Pressure SensorUse thread sealant15 lb-ft20 Nm
- Sensor Mounting Bolts10 lb-ft14 Nm
Oil Pump8 specs
- Electrical Connector Bolts6 lb-ft8 Nm
- Gasket Surface BoltsClean mating surfaces19 lb-ft26 Nm
- Oil Drain PlugUse new crush washer26 lb-ft35 Nm
- Oil Pan Bolt9 lb-ft12 Nm
- Oil Pump Bolts9 lb-ft12 Nm
- Oil Pump Pickup Tube9 lb-ft12 Nm
- Sensor Mounting Bolts10 lb-ft14 Nm
- Timing Cover Bolts - 8mmTighten in sequence18 lb-ft25 Nm
PCV Valve4 specs
- Electrical Connector Bolts6 lb-ft8 Nm
- Gasket Surface BoltsClean mating surfaces19 lb-ft26 Nm
- PCV ValveHand tight usually6 lb-ft8 Nm
- Sensor Mounting Bolts10 lb-ft14 Nm
Piston - Single7 specs
- Connecting Rod BoltsTTY - critical torque plus angle33 lb-ft45 Nm
- Cylinder Head BoltsTTY - tighten in sequence plus angle48 lb-ft65 Nm
- Electrical Connector Bolts6 lb-ft8 Nm
- Gasket Surface BoltsClean mating surfaces19 lb-ft26 Nm
- Oil Drain PlugUse new crush washer26 lb-ft35 Nm
- Oil Pan Bolt9 lb-ft12 Nm
- Sensor Mounting Bolts10 lb-ft14 Nm
Piston Rings - All9 specs
- Connecting Rod BoltsTTY - critical torque plus angle33 lb-ft45 Nm
- Cylinder Head BoltsTTY - tighten in sequence plus angle48 lb-ft65 Nm
- Electrical Connector Bolts6 lb-ft8 Nm
- Gasket Surface BoltsClean mating surfaces19 lb-ft26 Nm
- Main Bearing Cap BoltsTTY - tighten in sequence plus angle55 lb-ft75 Nm
- Oil Drain PlugUse new crush washer26 lb-ft35 Nm
- Oil Pan BoltTighten in sequence9 lb-ft12 Nm
- Oil Pump Pickup Tube9 lb-ft12 Nm
- Sensor Mounting Bolts10 lb-ft14 Nm
Pistons - All9 specs
- Connecting Rod BoltsTTY - critical torque plus angle33 lb-ft45 Nm
- Cylinder Head BoltsTTY - tighten in sequence plus angle48 lb-ft65 Nm
- Electrical Connector Bolts6 lb-ft8 Nm
- Gasket Surface BoltsClean mating surfaces19 lb-ft26 Nm
- Main Bearing Cap BoltsTTY - tighten in sequence plus angle55 lb-ft75 Nm
- Oil Drain PlugUse new crush washer26 lb-ft35 Nm
- Oil Pan Bolt9 lb-ft12 Nm
- Oil Pump Pickup Tube9 lb-ft12 Nm
- Sensor Mounting Bolts10 lb-ft14 Nm
Rear Main Seal9 specs
- Electrical Connector Bolts6 lb-ft8 Nm
- Flexplate BoltsAutomatic transmissions63 lb-ft85 Nm
- Flywheel BoltsOften TTY, tighten in star pattern70 lb-ft95 Nm
- Gasket Surface BoltsClean mating surfaces19 lb-ft26 Nm
- Oil Drain PlugUse new crush washer26 lb-ft35 Nm
- Oil Pan BoltRear section9 lb-ft12 Nm
- Rear Main Seal Housing9 lb-ft12 Nm
- Sensor Mounting Bolts10 lb-ft14 Nm
- Transmission-to-Engine Bolts41 lb-ft55 Nm
Rocker Arms - All7 specs
- Electrical Connector Bolts6 lb-ft8 Nm
- Gasket Surface BoltsClean mating surfaces19 lb-ft26 Nm
- Intake Manifold BoltIf pushrods18 lb-ft25 Nm
- Rocker Arm BoltsTighten with cam lobe pointing away22 lb-ft30 Nm
- Rocker Arm Shaft BoltsTighten evenly in sequence18 lb-ft25 Nm
- Sensor Mounting Bolts10 lb-ft14 Nm
- Valve Cover BoltsTighten in sequence7 lb-ft10 Nm
Serpentine Belt2 specs
- Belt Tensioner Bolt41 lb-ft55 Nm
- Idler Pulley Bolt33 lb-ft45 Nm
Serpentine Belt Tensioner4 specs
- Belt Tensioner Bolt41 lb-ft55 Nm
- Electrical Connector Bolts6 lb-ft8 Nm
- Gasket Surface BoltsClean mating surfaces19 lb-ft26 Nm
- Sensor Mounting Bolts10 lb-ft14 Nm
Short Block Replacement12 specs
- Connecting Rod BoltsTTY - critical torque plus angle33 lb-ft45 Nm
- Crankshaft Pulley BoltOften TTY - check spec, may require impact133 lb-ft180 Nm
- Electrical Connector Bolts6 lb-ft8 Nm
- Flywheel BoltsOften TTY, tighten in star pattern70 lb-ft95 Nm
- Gasket Surface BoltsClean mating surfaces19 lb-ft26 Nm
- Main Bearing Cap BoltsTTY - tighten in sequence plus angle55 lb-ft75 Nm
- Oil Drain PlugUse new crush washer26 lb-ft35 Nm
- Oil Pan Bolt9 lb-ft12 Nm
- Oil Pump Bolts9 lb-ft12 Nm
- Sensor Mounting Bolts10 lb-ft14 Nm
- Timing Cover Bolts - 8mmTighten in sequence18 lb-ft25 Nm
- Transmission-to-Engine Bolts41 lb-ft55 Nm
Throttle Body2 specs
- Air Intake Hose Clamps2 lb-ft3 Nm
- Throttle Body Bolts7 lb-ft10 Nm
Throttle Position Sensor4 specs
- Electrical Connector Bolts6 lb-ft8 Nm
- Gasket Surface BoltsClean mating surfaces19 lb-ft26 Nm
- Sensor Mounting Bolts10 lb-ft14 Nm
- TPS Screws2 lb-ft3 Nm
Timing Chain5 specs
- Camshaft Sprocket Bolts59 lb-ft80 Nm
- Crankshaft Pulley BoltOften TTY - check specs133 lb-ft + 90°180 Nm
- Timing Chain Guide Bolts9 lb-ft12 Nm
- Timing Chain Tensioner18 lb-ft25 Nm
- Timing Cover BoltTighten in sequence9 lb-ft12 Nm
Timing Chain Guide3 specs
- Front cover bolts (M8)18 lb-ft25 Nm
- Tensioner arm pivot bolt18 lb-ft25 Nm
- Timing chain guide bolts7.4 lb-ft10 Nm
Timing Chain Kit6 specs
- Cam phaser bolt81 lb-ft110 Nm
- Crankshaft Pulley Bolt89 lb-ft120 Nm
- Front cover bolts (M8)18 lb-ft25 Nm
- Primary chain tensioner bolts18 lb-ft25 Nm
- Timing chain guide bolts7.4 lb-ft10 Nm
- Valve Cover Bolts7.4 lb-ft10 Nm
Timing Chain Tensioner3 specs
- Tensioner Cap/PlugUse new crush washer if equipped22 lb-ft30 Nm
- Tensioner Housing BoltsTighten in sequence18 lb-ft25 Nm
- Timing Cover Access Bolts9 lb-ft12 Nm
Transmission Mount7 specs
- Crossmember Bolt70 lb-ft95 Nm
- Drain PlugUse new washer31 lb-ft42 Nm
- Fill Plug31 lb-ft42 Nm
- Flywheel BoltsOften TTY, tighten in star pattern70 lb-ft95 Nm
- Transmission Drain PlugUse new crush washer if equipped22 lb-ft30 Nm
- Transmission Mount Bolts48 lb-ft65 Nm
- Transmission Pan BoltsTighten in criss-cross pattern9 lb-ft12 Nm
Valve Adjustment6 specs
- Electrical Connector Bolts6 lb-ft8 Nm
- Gasket Surface BoltsClean mating surfaces19 lb-ft26 Nm
- Rocker Arm BoltsTighten with cam lobe pointing away22 lb-ft30 Nm
- Sensor Mounting Bolts10 lb-ft14 Nm
- Valve Cover BoltsTighten in sequence7 lb-ft10 Nm
- Valve Lash Adjusting Screw Lock NutHold screw while tightening15 lb-ft20 Nm
Valve Cover Gasket - Single2 specs
- Spark Plug Tube SealsIf equipped with separate seals9 lb-ft12 Nm
- Valve Cover BoltsTighten in sequence7 lb-ft10 Nm
Valve Cover Gaskets - Both7 specs
- Electrical Connector Bolts6 lb-ft8 Nm
- Gasket Surface BoltsClean mating surfaces19 lb-ft26 Nm
- Ignition Coil Bolt6 lb-ft8 Nm
- Intake Manifold BoltIf required18 lb-ft25 Nm
- Sensor Mounting Bolts10 lb-ft14 Nm
- Spark Plugs - Aluminum HeadApply anti-seize to threads15 lb-ft20 Nm
- Valve Cover BoltsTighten in sequence7 lb-ft10 Nm
Valve Job - Complete12 specs
- Camshaft Cap BoltsTighten in sequence from center outward, multiple passes10 lb-ft14 Nm
- Camshaft Sprocket BoltsHold cam with wrench on hex59 lb-ft80 Nm
- Cylinder Head BoltsTTY - tighten in sequence plus angle48 lb-ft65 Nm
- Electrical Connector Bolts6 lb-ft8 Nm
- Exhaust Manifold NutsApply anti-seize, work hot-to-cold22 lb-ft30 Nm
- Gasket Surface BoltsClean mating surfaces19 lb-ft26 Nm
- Intake Manifold Bolt18 lb-ft25 Nm
- Rocker Arm BoltsTighten with cam lobe pointing away22 lb-ft30 Nm
- Sensor Mounting Bolts10 lb-ft14 Nm
- Timing Chain Tensioner BoltInstall with pin/clip to compress18 lb-ft25 Nm
- Timing Cover Bolts - 8mmTighten in sequence18 lb-ft25 Nm
- Valve Cover BoltsTighten in sequence7 lb-ft10 Nm
Valve Seals8 specs
- Camshaft Cap BoltsTighten in sequence from center outward, multiple passes10 lb-ft14 Nm
- Electrical Connector Bolts6 lb-ft8 Nm
- Gasket Surface BoltsClean mating surfaces19 lb-ft26 Nm
- Rocker Arm BoltsTighten with cam lobe pointing away22 lb-ft30 Nm
- Rocker Arm Shaft BoltsTighten evenly in sequence18 lb-ft25 Nm
- Sensor Mounting Bolts10 lb-ft14 Nm
- Spark Plugs - Aluminum HeadApply anti-seize to threads15 lb-ft20 Nm
- Valve Cover BoltsTighten in sequence7 lb-ft10 Nm
Valve Spring - Single6 specs
- Electrical Connector Bolts6 lb-ft8 Nm
- Gasket Surface BoltsClean mating surfaces19 lb-ft26 Nm
- Rocker Arm BoltsTighten with cam lobe pointing away22 lb-ft30 Nm
- Sensor Mounting Bolts10 lb-ft14 Nm
- Spark Plugs - Aluminum HeadApply anti-seize to threads15 lb-ft20 Nm
- Valve Cover BoltsTighten in sequence7 lb-ft10 Nm
Valve Springs - All8 specs
- Camshaft Cap BoltsTighten in sequence from center outward, multiple passes10 lb-ft14 Nm
- Electrical Connector Bolts6 lb-ft8 Nm
- Gasket Surface BoltsClean mating surfaces19 lb-ft26 Nm
- Rocker Arm BoltsTighten with cam lobe pointing away22 lb-ft30 Nm
- Rocker Arm Shaft BoltsTighten evenly in sequence18 lb-ft25 Nm
- Sensor Mounting Bolts10 lb-ft14 Nm
- Spark Plugs - Aluminum HeadApply anti-seize to threads15 lb-ft20 Nm
- Valve Cover BoltsTighten in sequence7 lb-ft10 Nm
Cooling
Coolant Bypass Pipe8 specs
- Bleed ScrewOpen during fill6 lb-ft8 Nm
- Coolant Drain Plug11 lb-ft15 Nm
- Drain PetcockHand tight6 lb-ft8 Nm
- Fan Bolts10 lb-ft14 Nm
- Hose Clamps2 lb-ft3 Nm
- Pump BoltsTorque in sequence22 lb-ft30 Nm
- Thermostat Housing Bolt11 lb-ft15 Nm
- Water Pump BoltsTighten in criss-cross pattern18 lb-ft25 Nm
Coolant Flush12 specs
- Air Box Clips4 lb-ft5 Nm
- Bleed ScrewOpen during fill6 lb-ft8 Nm
- Block Drain PlugIf equipped, use new washer18 lb-ft25 Nm
- Connector Bolts6 lb-ft8 Nm
- Coolant Hose Clamps4 lb-ft5 Nm
- Drain Petcock4 lb-ft5 Nm
- Drain Plug11 lb-ft15 Nm
- Hose Clamps4 lb-ft5 Nm
- Oil Drain PlugUse new crush washer26 lb-ft35 Nm
- Pump Bolts23 lb-ft31 Nm
- Radiator CapHand tight1 lb-ft1 Nm
- Wheel Lug NutsTorque in star pattern105 lb-ft142.4 Nm
Coolant Reservoir9 specs
- Bleed ScrewOpen during fill6 lb-ft8 Nm
- Coolant Drain Plug11 lb-ft15 Nm
- Drain PetcockHand tight6 lb-ft8 Nm
- Fan Bolts10 lb-ft14 Nm
- Hose ClampsDo not overtighten4 lb-ft5 Nm
- Pump BoltsTorque in sequence22 lb-ft30 Nm
- Reservoir Mounting Bolts6 lb-ft8 Nm
- Thermostat Housing Bolt12 lb-ft16 Nm
- Water Pump BoltsTighten in criss-cross pattern18 lb-ft25 Nm
Coolant Temperature Sensor7 specs
- Bleed ScrewOpen during fill6 lb-ft8 Nm
- Coolant Drain Plug11 lb-ft15 Nm
- Drain PetcockHand tight6 lb-ft8 Nm
- Fan Bolts10 lb-ft14 Nm
- Hose Clamps2 lb-ft3 Nm
- Pump BoltsTorque in sequence22 lb-ft30 Nm
- Thermostat Housing Bolt11 lb-ft15 Nm
Cooling Fan Assembly6 specs
- Coolant Drain Plug11 lb-ft15 Nm
- Drain PetcockHand tight6 lb-ft8 Nm
- Fan Bolts10 lb-ft14 Nm
- Hose Clamps2 lb-ft3 Nm
- Pump BoltsTorque in sequence22 lb-ft30 Nm
- Thermostat Housing Bolt11 lb-ft15 Nm
Cooling Fan Clutch5 specs
- Drain PetcockHand tight6 lb-ft8 Nm
- Fan Bolts10 lb-ft14 Nm
- Hose Clamps2 lb-ft3 Nm
- Pump BoltsTorque in sequence22 lb-ft30 Nm
- Thermostat Housing Bolt11 lb-ft15 Nm
Cooling Fan Motor7 specs
- Drain PetcockHand tight6 lb-ft8 Nm
- Electrical Connector4 lb-ft5 Nm
- Fan Bolts10 lb-ft14 Nm
- Fan Motor Bolts6 lb-ft8 Nm
- Hose Clamps4 lb-ft5 Nm
- Pump BoltsTorque in sequence22 lb-ft30 Nm
- Thermostat Housing Bolt12 lb-ft16 Nm
Cooling Fan Relay4 specs
- Drain PetcockHand tight6 lb-ft8 Nm
- Fan Bolts10 lb-ft14 Nm
- Pump BoltsTorque in sequence22 lb-ft30 Nm
- Thermostat Housing Bolt11 lb-ft15 Nm
Engine Oil Cooler6 specs
- Coolant Drain Plug11 lb-ft15 Nm
- Drain PetcockHand tight6 lb-ft8 Nm
- Fan Bolts10 lb-ft14 Nm
- Hose Clamps2 lb-ft3 Nm
- Pump BoltsTorque in sequence22 lb-ft30 Nm
- Thermostat Housing Bolt11 lb-ft15 Nm
Heater Control Valve6 specs
- Drain PetcockHand tight6 lb-ft8 Nm
- Fan Bolts10 lb-ft14 Nm
- Hose Clamps2 lb-ft3 Nm
- Pump BoltsTorque in sequence22 lb-ft30 Nm
- Thermostat Housing Bolt12 lb-ft16 Nm
- Valve Mounting6 lb-ft8 Nm
Heater Core8 specs
- Dashboard Screws2 lb-ft3 Nm
- Drain PetcockHand tight6 lb-ft8 Nm
- Fan Bolts10 lb-ft14 Nm
- Heater Core Mounting6 lb-ft8 Nm
- Heater Hose Clamps2 lb-ft3 Nm
- Hose ClampsDo not overtighten4 lb-ft5 Nm
- Pump BoltsTorque in sequence22 lb-ft30 Nm
- Thermostat Housing Bolt12 lb-ft16 Nm
Heater Hoses6 specs
- Coolant Drain Plug11 lb-ft15 Nm
- Drain PetcockHand tight6 lb-ft8 Nm
- Fan Bolts10 lb-ft14 Nm
- Hose Clamps2 lb-ft3 Nm
- Pump BoltsTorque in sequence22 lb-ft30 Nm
- Thermostat Housing Bolt11 lb-ft15 Nm
Radiator4 specs
- Drain PetcockPlastic - hand tight4 lb-ft5 Nm
- Radiator Mounting BoltDo not overtighten plastic mounts9 lb-ft12 Nm
- Transmission Cooler LinesIf equipped18 lb-ft25 Nm
- Upper/Lower Hose Clamps2 lb-ft3 Nm
Radiator Cap4 specs
- Drain PetcockHand tight6 lb-ft8 Nm
- Fan Bolts10 lb-ft14 Nm
- Pump BoltsTorque in sequence22 lb-ft30 Nm
- Thermostat Housing Bolt11 lb-ft15 Nm
Radiator Hose - Lower5 specs
- Drain PetcockHand tight6 lb-ft8 Nm
- Fan Bolts10 lb-ft14 Nm
- Hose Clamps2 lb-ft3 Nm
- Pump BoltsTorque in sequence22 lb-ft30 Nm
- Thermostat Housing Bolt12 lb-ft16 Nm
Radiator Hose - Upper5 specs
- Drain PetcockHand tight6 lb-ft8 Nm
- Fan Bolts10 lb-ft14 Nm
- Hose Clamps2 lb-ft3 Nm
- Pump BoltsTorque in sequence22 lb-ft30 Nm
- Thermostat Housing Bolt12 lb-ft16 Nm
Radiator Hoses - Both6 specs
- Coolant Drain Plug11 lb-ft15 Nm
- Drain PetcockHand tight6 lb-ft8 Nm
- Fan Bolts10 lb-ft14 Nm
- Hose Clamps2 lb-ft3 Nm
- Pump BoltsTorque in sequence22 lb-ft30 Nm
- Thermostat Housing Bolt11 lb-ft15 Nm
Radiator Removal and Service4 specs
- Drain PetcockPlastic - hand-tight only4 lb-ft5 Nm
- Fan Shroud Bolts7 lb-ft10 Nm
- Radiator Mounting BoltDo not overtighten plastic mounts9 lb-ft12 Nm
- Transmission Cooler LinesIf equipped, use new washers18 lb-ft25 Nm
Thermostat2 specs
- Coolant Temperature SensorUse thread sealant15 lb-ft20 Nm
- Thermostat Housing Bolt11 lb-ft15 Nm
Thermostat Housing8 specs
- Coolant Drain Plug11 lb-ft15 Nm
- Coolant Hose Clamps4 lb-ft5 Nm
- Drain PetcockHand tight6 lb-ft8 Nm
- Fan Bolts10 lb-ft14 Nm
- Hose Clamps2 lb-ft3 Nm
- Pump BoltsTorque in sequence22 lb-ft30 Nm
- Thermostat Housing Bolt11 lb-ft15 Nm
- Water Pump BoltsTighten in criss-cross pattern18 lb-ft25 Nm
Water Pump3 specs
- Hose ClampsSpring clamps preferred2 lb-ft3 Nm
- Thermostat Housing Bolt11 lb-ft15 Nm
- Water Pump BoltsTighten in criss-cross pattern18 lb-ft25 Nm
Ignition
Coil Pack3 specs
- Connector Bolts6 lb-ft8 Nm
- Ignition Coil Bolt6 lb-ft8 Nm
- Spark Plugs - Aluminum HeadApply anti-seize to threads15 lb-ft20 Nm
Ignition Coil - Single3 specs
- Connector Bolts6 lb-ft8 Nm
- Ignition Coil Bolt6 lb-ft8 Nm
- Spark Plugs - Aluminum HeadApply anti-seize to threads15 lb-ft20 Nm
Ignition Coils - All3 specs
- Connector Bolts6 lb-ft8 Nm
- Ignition Coil Bolt6 lb-ft8 Nm
- Spark Plugs - Aluminum HeadApply anti-seize to threads15 lb-ft20 Nm
Ignition Control Module2 specs
- Connector Bolts6 lb-ft8 Nm
- Ignition Coil Bolt6 lb-ft8 Nm
Ignition Lock Cylinder2 specs
- Connector Bolts6 lb-ft8 Nm
- Ignition Coil Bolt6 lb-ft8 Nm
Ignition Switch3 specs
- Connector Bolts6 lb-ft8 Nm
- Steering Column Bolts22 lb-ft30 Nm
- Switch Mounting Screws4 lb-ft5 Nm
Spark Plug Wires5 specs
- Connector Bolts6 lb-ft8 Nm
- Engine Cover Clips3 lb-ft3 Nm
- Ignition Coil Bolt6 lb-ft8 Nm
- Spark PlugGap before install19 lb-ft25 Nm
- Spark Plugs - Aluminum HeadApply anti-seize to threads15 lb-ft20 Nm
Spark Plugs8 specs
- Air Box Clips4 lb-ft5 Nm
- Connector Bolts6 lb-ft8 Nm
- Engine Cover Clips3 lb-ft3 Nm
- Ignition Coil Bolt6 lb-ft8 Nm
- Oil Drain PlugUse new crush washer26 lb-ft35 Nm
- Spark PlugGap before install19 lb-ft25 Nm
- Spark Plugs - Aluminum HeadApply anti-seize to threads15 lb-ft20 Nm
- Wheel Lug NutsTorque in star pattern105 lb-ft142.4 Nm
Fuel system
Charcoal Canister5 specs
- Filter Bracket10 lb-ft14 Nm
- Fuel Line FittingsUse new O-rings18 lb-ft25 Nm
- Hose Clamps2 lb-ft3 Nm
- Pressure Regulator Screws6 lb-ft8 Nm
- Pump Mounting12 lb-ft16 Nm
EVAP Purge Valve4 specs
- Filter Bracket10 lb-ft14 Nm
- Hose Clamps2 lb-ft3 Nm
- Pressure Regulator Screws6 lb-ft8 Nm
- Pump Mounting12 lb-ft16 Nm
EVAP Vent Valve4 specs
- Filter Bracket10 lb-ft14 Nm
- Hose Clamps2 lb-ft3 Nm
- Pressure Regulator Screws6 lb-ft8 Nm
- Pump Mounting12 lb-ft16 Nm
Fuel Cap3 specs
- Filter Bracket10 lb-ft14 Nm
- Pressure Regulator Screws6 lb-ft8 Nm
- Pump Mounting12 lb-ft16 Nm
Fuel Filler Neck6 specs
- Filler Neck Bolts7 lb-ft10 Nm
- Filter Bracket10 lb-ft14 Nm
- Fuel Rail Bolts19 lb-ft25 Nm
- Hose Clamps2 lb-ft3 Nm
- Pressure Regulator Screws6 lb-ft8 Nm
- Pump Mounting12 lb-ft16 Nm
Fuel Filter7 specs
- Air Box Clips4 lb-ft5 Nm
- Connector Bolts6 lb-ft8 Nm
- Filter Bracket Bolt13 lb-ft17 Nm
- Fuel Filter Bracket Bolt7 lb-ft10 Nm
- Fuel Line FittingsIf threaded type18 lb-ft25 Nm
- Oil Drain PlugUse new crush washer26 lb-ft35 Nm
- Wheel Lug NutsTorque in star pattern105 lb-ft142.4 Nm
Fuel Filter - In-Tank6 specs
- Filter Bracket10 lb-ft14 Nm
- Filter Bracket Bolt13 lb-ft17 Nm
- Fuel Line FittingsUse new O-rings18 lb-ft25 Nm
- Hose Clamps2 lb-ft3 Nm
- Pressure Regulator Screws6 lb-ft8 Nm
- Pump Mounting12 lb-ft16 Nm
Fuel Injector - Single6 specs
- Filter Bracket10 lb-ft14 Nm
- Fuel Line FittingsUse new O-rings18 lb-ft25 Nm
- Fuel Rail Bolts9 lb-ft12 Nm
- Hose Clamps2 lb-ft3 Nm
- Pressure Regulator Screws6 lb-ft8 Nm
- Pump Mounting12 lb-ft16 Nm
Fuel Injector Cleaning6 specs
- Filter Bracket10 lb-ft14 Nm
- Fuel Line FittingsUse new O-rings18 lb-ft25 Nm
- Fuel Rail Bolts9 lb-ft12 Nm
- Hose Clamps2 lb-ft3 Nm
- Pressure Regulator Screws6 lb-ft8 Nm
- Pump Mounting12 lb-ft16 Nm
Fuel Injectors - All6 specs
- Filter Bracket10 lb-ft14 Nm
- Fuel Line FittingsUse new O-rings18 lb-ft25 Nm
- Fuel Rail Bolts9 lb-ft12 Nm
- Hose Clamps2 lb-ft3 Nm
- Pressure Regulator Screws6 lb-ft8 Nm
- Pump Mounting12 lb-ft16 Nm
Fuel Level Sensor5 specs
- Filter Bracket10 lb-ft14 Nm
- Fuel Line FittingsUse new O-rings18 lb-ft25 Nm
- Hose Clamps2 lb-ft3 Nm
- Pressure Regulator Screws6 lb-ft8 Nm
- Pump Mounting12 lb-ft16 Nm
Fuel Line - High Pressure6 specs
- Filter Bracket10 lb-ft14 Nm
- Fuel Line FittingsUse new O-rings18 lb-ft25 Nm
- Fuel Rail Bolts9 lb-ft12 Nm
- Hose Clamps2 lb-ft3 Nm
- Pressure Regulator Screws6 lb-ft8 Nm
- Pump Mounting12 lb-ft16 Nm
Fuel Line - Return6 specs
- Filter Bracket10 lb-ft14 Nm
- Fuel Line FittingsUse new O-rings18 lb-ft25 Nm
- Fuel Rail Bolts9 lb-ft12 Nm
- Hose Clamps2 lb-ft3 Nm
- Pressure Regulator Screws6 lb-ft8 Nm
- Pump Mounting12 lb-ft16 Nm
Fuel Pressure Regulator6 specs
- Filter Bracket10 lb-ft14 Nm
- Fuel Line18 lb-ft25 Nm
- Fuel Rail Bolts19 lb-ft25 Nm
- Pressure Regulator Screws6 lb-ft8 Nm
- Pump Mounting12 lb-ft16 Nm
- Regulator Mounting Screws4 lb-ft5 Nm
Fuel Pump2 specs
- Fuel Pump Module Lock RingUse special tool59 lb-ft80 Nm
- Tank Strap Bolts26 lb-ft35 Nm
Fuel Pump Module7 specs
- Access Cover Screws4 lb-ft5 Nm
- Filter Bracket10 lb-ft14 Nm
- Fuel Line FittingsUse new O-rings18 lb-ft25 Nm
- Fuel Pump Lock RingLock ring tool63 lb-ft85 Nm
- Hose Clamps2 lb-ft3 Nm
- Pressure Regulator Screws6 lb-ft8 Nm
- Pump Mounting12 lb-ft16 Nm
Fuel Rail6 specs
- Filter Bracket10 lb-ft14 Nm
- Fuel Line FittingsUse new O-rings18 lb-ft25 Nm
- Fuel Rail Bolts9 lb-ft12 Nm
- Hose Clamps2 lb-ft3 Nm
- Pressure Regulator Screws6 lb-ft8 Nm
- Pump Mounting12 lb-ft16 Nm
Fuel Tank7 specs
- Filler Neck Clamp3 lb-ft4 Nm
- Filter Bracket10 lb-ft14 Nm
- Fuel Line FittingsUse new O-rings18 lb-ft25 Nm
- Fuel Rail Bolts19 lb-ft25 Nm
- Pressure Regulator Screws6 lb-ft8 Nm
- Pump Mounting12 lb-ft16 Nm
- Tank Strap Bolts26 lb-ft35 Nm
Fuel Tank Strap5 specs
- Filter Bracket10 lb-ft14 Nm
- Fuel Line FittingsUse new O-rings18 lb-ft25 Nm
- Hose Clamps2 lb-ft3 Nm
- Pressure Regulator Screws6 lb-ft8 Nm
- Pump Mounting12 lb-ft16 Nm
High Pressure Fuel Pump5 specs
- Filter Bracket10 lb-ft14 Nm
- Fuel Line FittingsUse new O-rings18 lb-ft25 Nm
- Hose Clamps2 lb-ft3 Nm
- Pressure Regulator Screws6 lb-ft8 Nm
- Pump Mounting12 lb-ft16 Nm
Electrical
Airbag - Driver5 specs
- Airbag Module BoltsTorx - disconnect battery and wait 2 minutes5 lb-ft7 Nm
- Battery Terminal Bolts6 lb-ft8 Nm
- Connector Screws4 lb-ft5 Nm
- Ground Strap BoltsClean contact surfaces12 lb-ft16 Nm
- Steering Wheel Nut40 lb-ft54 Nm
Airbag - Passenger5 specs
- Airbag Module BoltsTorx - disconnect battery and wait 2 minutes5 lb-ft7 Nm
- Battery Terminal Bolts6 lb-ft8 Nm
- Connector Screws4 lb-ft5 Nm
- Dashboard Fasteners3 lb-ft4 Nm
- Ground Strap BoltsClean contact surfaces12 lb-ft16 Nm
Airbag - Side5 specs
- Battery Terminal Bolts6 lb-ft8 Nm
- Connector Screws4 lb-ft5 Nm
- Ground Strap BoltsClean contact surfaces12 lb-ft16 Nm
- Seat Mounting BoltsSafety critical45 lb-ft61 Nm
- Side Airbag Module BoltsTorx5 lb-ft7 Nm
Airbag Module/Computer4 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws4 lb-ft5 Nm
- Module Mounting Bolts6 lb-ft8 Nm
- Sensor Mounting Bolts7 lb-ft10 Nm
Alternator4 specs
- Alternator Mounting Bolts37 lb-ft50 Nm
- Alternator Pivot Bolt18 lb-ft25 Nm
- Battery Terminal BoltsDo not overtighten6 lb-ft8 Nm
- Serpentine Belt Tensioner41 lb-ft55 Nm
Alternator Belt4 specs
- Alternator Mounting Bolts44 lb-ft59 Nm
- Alternator Pivot Bolt44 lb-ft59 Nm
- Battery Cable Nut13 lb-ft17 Nm
- Connector Screws4 lb-ft5 Nm
Amplifier4 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws4 lb-ft5 Nm
- Ground Strap BoltsEnsure clean contact9 lb-ft12 Nm
- Module Mounting Bolts6 lb-ft8 Nm
Antenna2 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws4 lb-ft5 Nm
Backup Camera4 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws4 lb-ft5 Nm
- Module Mounting Bolts6 lb-ft8 Nm
- Sensor Mounting Bolts7 lb-ft10 Nm
Battery3 specs
- Battery Hold-Down Bolt6 lb-ft8 Nm
- Battery Terminal BoltsDo not overtighten - can crack terminal4 lb-ft6 Nm
- Battery Tray Bolts9 lb-ft12 Nm
Battery Cable - Negative6 specs
- Battery Hold-Down BoltDo not overtighten10 lb-ft14 Nm
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws4 lb-ft5 Nm
- Ground Cable Bolt13 lb-ft17 Nm
- Ground Strap BoltsEnsure clean contact9 lb-ft12 Nm
- Sensor Mounting Bolts7 lb-ft10 Nm
Battery Cable - Positive5 specs
- Battery Hold-Down BoltDo not overtighten10 lb-ft14 Nm
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws4 lb-ft5 Nm
- Ground Cable Bolt13 lb-ft17 Nm
- Module Mounting Bolts6 lb-ft8 Nm
Battery Cables - Both6 specs
- Battery Hold-Down BoltDo not overtighten10 lb-ft14 Nm
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws4 lb-ft5 Nm
- Ground Cable Bolt13 lb-ft17 Nm
- Ground Strap BoltsEnsure clean contact9 lb-ft12 Nm
- Sensor Mounting Bolts7 lb-ft10 Nm
Battery Terminal6 specs
- Battery Hold-Down BoltDo not overtighten10 lb-ft14 Nm
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws4 lb-ft5 Nm
- Ground Cable Bolt13 lb-ft17 Nm
- Ground Strap BoltsEnsure clean contact9 lb-ft12 Nm
- Sensor Mounting Bolts7 lb-ft10 Nm
Blower Motor2 specs
- Blower Motor Mounting Screw3 lb-ft4 Nm
- Blower Motor Resistor Screws1.5 lb-ft2 Nm
Blower Motor Control Module3 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws4 lb-ft5 Nm
- Module Mounting Bolts6 lb-ft8 Nm
Blower Motor Resistor4 specs
- Battery Terminal Bolts6 lb-ft8 Nm
- Connector Screws4 lb-ft5 Nm
- Ground Strap BoltsClean contact surfaces12 lb-ft16 Nm
- Resistor Screws1.5 lb-ft2 Nm
Clock Spring7 specs
- Airbag Module BoltsTorx - disconnect battery first5 lb-ft7 Nm
- Battery Terminal Bolts6 lb-ft8 Nm
- Clock Spring ScrewsAlign marks before removal3 lb-ft4 Nm
- Connector Screws4 lb-ft5 Nm
- Ground Strap BoltsClean contact surfaces12 lb-ft16 Nm
- Steering Column CoversPlastic clips2 lb-ft3 Nm
- Steering Wheel Nut40 lb-ft54 Nm
Combination Switch4 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws4 lb-ft5 Nm
- Module Mounting Bolts6 lb-ft8 Nm
- Sensor Mounting Bolts7 lb-ft10 Nm
Dimmer Switch3 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws4 lb-ft5 Nm
- Module Mounting Bolts6 lb-ft8 Nm
Door Lock Actuator - Front2 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws4 lb-ft5 Nm
Door Lock Actuator - Rear2 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws4 lb-ft5 Nm
Fog Light Assembly2 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws4 lb-ft5 Nm
Fog Light Bulb1 spec
- Connector Screws4 lb-ft5 Nm
Fuel Pump Relay6 specs
- Access Cover Screws4 lb-ft5 Nm
- Battery Terminal Bolts6 lb-ft8 Nm
- Connector Screws4 lb-ft5 Nm
- Fuel Pump Lock RingLock ring tool63 lb-ft85 Nm
- Ground Strap BoltsClean contact surfaces12 lb-ft16 Nm
- Relay Socket4 lb-ft5 Nm
Fuse Box - Engine Bay4 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws4 lb-ft5 Nm
- Ground Strap BoltsEnsure clean contact9 lb-ft12 Nm
- Module Mounting Bolts6 lb-ft8 Nm
Fuse Box - Interior4 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws4 lb-ft5 Nm
- Ground Strap BoltsEnsure clean contact9 lb-ft12 Nm
- Module Mounting Bolts6 lb-ft8 Nm
Headlight Assembly5 specs
- Adjuster Screws2 lb-ft3 Nm
- Battery Terminal Bolts6 lb-ft8 Nm
- Connector Screws4 lb-ft5 Nm
- Ground Strap BoltsClean contact surfaces12 lb-ft16 Nm
- Headlight Assembly Bolts7 lb-ft10 Nm
Headlight Bulb - Single4 specs
- Battery Terminal Bolts6 lb-ft8 Nm
- Bulb Retaining Ring4 lb-ft5 Nm
- Connector Screws4 lb-ft5 Nm
- Ground Strap BoltsClean contact surfaces12 lb-ft16 Nm
Headlight Bulbs - Pair1 spec
- Connector Screws4 lb-ft5 Nm
Headlight Switch3 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws4 lb-ft5 Nm
- Module Mounting Bolts6 lb-ft8 Nm
Heated Seat Module3 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws4 lb-ft5 Nm
- Module Mounting Bolts6 lb-ft8 Nm
HID Ballast3 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws4 lb-ft5 Nm
- Module Mounting Bolts6 lb-ft8 Nm
Horn4 specs
- Battery Terminal Bolts6 lb-ft8 Nm
- Connector Screws4 lb-ft5 Nm
- Ground Strap BoltsClean contact surfaces12 lb-ft16 Nm
- Horn Mounting Bolt11 lb-ft15 Nm
Horn Relay2 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws4 lb-ft5 Nm
Instrument Cluster3 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws4 lb-ft5 Nm
- Module Mounting Bolts6 lb-ft8 Nm
LED Headlight Module3 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws4 lb-ft5 Nm
- Module Mounting Bolts6 lb-ft8 Nm
Main Relay3 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws4 lb-ft5 Nm
- Module Mounting Bolts6 lb-ft8 Nm
Power Antenna Motor2 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws4 lb-ft5 Nm
Power Mirror Motor2 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws4 lb-ft5 Nm
Power Seat Motor3 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws4 lb-ft5 Nm
- Module Mounting Bolts6 lb-ft8 Nm
Power Window Motor - Front3 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws4 lb-ft5 Nm
- Module Mounting Bolts6 lb-ft8 Nm
Power Window Motor - Rear3 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws4 lb-ft5 Nm
- Module Mounting Bolts6 lb-ft8 Nm
Power Window Regulator - Front3 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws4 lb-ft5 Nm
- Module Mounting Bolts6 lb-ft8 Nm
Power Window Regulator - Rear2 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws4 lb-ft5 Nm
Radio/Head Unit3 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws4 lb-ft5 Nm
- Module Mounting Bolts6 lb-ft8 Nm
Relay - Generic3 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws4 lb-ft5 Nm
- Module Mounting Bolts6 lb-ft8 Nm
Seat Heater Element4 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws4 lb-ft5 Nm
- Module Mounting Bolts6 lb-ft8 Nm
- Sensor Mounting Bolts7 lb-ft10 Nm
Side Mirror Assembly2 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws4 lb-ft5 Nm
Speaker - Dash3 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws4 lb-ft5 Nm
- Sensor Mounting Bolts7 lb-ft10 Nm
Speaker - Door2 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws4 lb-ft5 Nm
Speedometer4 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws4 lb-ft5 Nm
- Module Mounting Bolts6 lb-ft8 Nm
- Sensor Mounting Bolts7 lb-ft10 Nm
Starter3 specs
- Heat Shield BoltsIf equipped7 lb-ft10 Nm
- Starter Mounting BoltLong bolt may need extension37 lb-ft50 Nm
- Starter Solenoid NutFor B+ cable9 lb-ft12 Nm
Starter Solenoid4 specs
- Battery Cable Nut13 lb-ft17 Nm
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws4 lb-ft5 Nm
- Starter Mounting Bolt44 lb-ft59 Nm
Subwoofer3 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws4 lb-ft5 Nm
- Module Mounting Bolts6 lb-ft8 Nm
Sunroof Motor3 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws4 lb-ft5 Nm
- Module Mounting Bolts6 lb-ft8 Nm
Sunroof Switch2 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws4 lb-ft5 Nm
Tail Light Assembly5 specs
- Battery Terminal Bolts6 lb-ft8 Nm
- Connector Screws4 lb-ft5 Nm
- Ground Strap BoltsClean contact surfaces12 lb-ft16 Nm
- Lens Screws1.5 lb-ft2 Nm
- Tail Light Bolts6 lb-ft8 Nm
Tail Light Bulb1 spec
- Connector Screws4 lb-ft5 Nm
Third Brake Light1 spec
- Connector Screws4 lb-ft5 Nm
Trunk/Liftgate Actuator2 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws4 lb-ft5 Nm
Turn Signal Bulb - Front1 spec
- Connector Screws4 lb-ft5 Nm
Turn Signal Bulb - Rear1 spec
- Connector Screws4 lb-ft5 Nm
Turn Signal Switch5 specs
- Battery Terminal Bolts6 lb-ft8 Nm
- Connector Screws4 lb-ft5 Nm
- Ground Strap BoltsClean contact surfaces12 lb-ft16 Nm
- Steering Column Covers1.5 lb-ft2 Nm
- Switch Mounting Screws2 lb-ft3 Nm
Voltage Regulator3 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws4 lb-ft5 Nm
- Module Mounting Bolts6 lb-ft8 Nm
Washer Pump2 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws4 lb-ft5 Nm
Washer Reservoir3 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws4 lb-ft5 Nm
- Sensor Mounting Bolts7 lb-ft10 Nm
Window Motor and Regulator - Front3 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws4 lb-ft5 Nm
- Module Mounting Bolts6 lb-ft8 Nm
Window Motor and Regulator - Rear3 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws4 lb-ft5 Nm
- Module Mounting Bolts6 lb-ft8 Nm
Wiper Linkage7 specs
- Battery Terminal Bolts6 lb-ft8 Nm
- Connector Screws4 lb-ft5 Nm
- Ground Strap BoltsEnsure clean contact9 lb-ft12 Nm
- Linkage Pivot Nuts9 lb-ft12 Nm
- Module Mounting Bolts6 lb-ft8 Nm
- Motor Mounting Bolts7 lb-ft10 Nm
- Sensor Mounting Bolts7 lb-ft10 Nm
Wiper Motor - Front3 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws4 lb-ft5 Nm
- Module Mounting Bolts6 lb-ft8 Nm
Wiper Motor - Rear2 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws4 lb-ft5 Nm
Wiper Switch2 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws4 lb-ft5 Nm
Suspension
Ball Joint - Lower7 specs
- Control Arm BoltsTorque with vehicle weight on wheels122 lb-ft165 Nm
- Lower Ball Joint NutUse new cotter pin81 lb-ft110 Nm
- Pinch BoltNew bolt56 lb-ft76 Nm
- Strut Bolts106 lb-ft144 Nm
- Sway Bar Link56 lb-ft76 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug Nuts100 lb-ft136 Nm
Ball Joints - Upper and Lower8 specs
- Control Arm BoltsTorque with vehicle weight on wheels122 lb-ft165 Nm
- Lower Ball Joint Nut81 lb-ft110 Nm
- Pinch BoltNew bolt56 lb-ft76 Nm
- Strut Bolts106 lb-ft144 Nm
- Strut Tower Nuts37 lb-ft50 Nm
- Sway Bar Link56 lb-ft76 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug NutsTorque in star pattern100 lb-ft136 Nm
Coil Spring - Front6 specs
- Control Arm BoltsTorque with vehicle weight on wheels122 lb-ft165 Nm
- Strut Bolts106 lb-ft144 Nm
- Strut Tower Nuts37 lb-ft50 Nm
- Sway Bar Link56 lb-ft76 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug NutsTorque in star pattern100 lb-ft136 Nm
Coil Spring - Rear4 specs
- Control Arm BoltsTorque with vehicle weight on wheels122 lb-ft165 Nm
- Sway Bar Link56 lb-ft76 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug Nuts100 lb-ft136 Nm
Coil Springs - Front Pair6 specs
- Control Arm BoltsTorque with vehicle weight on wheels122 lb-ft165 Nm
- Strut Bolts106 lb-ft144 Nm
- Strut Tower Nuts37 lb-ft50 Nm
- Sway Bar Link56 lb-ft76 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug NutsTorque in star pattern100 lb-ft136 Nm
Coil Springs - Rear Pair4 specs
- Control Arm BoltsTorque with vehicle weight on wheels122 lb-ft165 Nm
- Sway Bar Link56 lb-ft76 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug Nuts100 lb-ft136 Nm
Control Arm Bushing - Front Lower6 specs
- Control Arm BoltsTorque with vehicle weight on wheels122 lb-ft165 Nm
- Lower Ball Joint NutNew cotter pin81 lb-ft110 Nm
- Strut Bolts106 lb-ft144 Nm
- Sway Bar Link56 lb-ft76 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug Nuts100 lb-ft136 Nm
Control Arm Bushing - Rear4 specs
- Control Arm BoltsTorque with vehicle weight on wheels122 lb-ft165 Nm
- Sway Bar Link56 lb-ft76 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug Nuts100 lb-ft136 Nm
Front Struts - Pair7 specs
- Control Arm BoltsTorque with vehicle weight on wheels122 lb-ft165 Nm
- Strut Bolts106 lb-ft144 Nm
- Strut to Knuckle Bolts113 lb-ft153 Nm
- Strut Tower Nuts37 lb-ft50 Nm
- Sway Bar Link56 lb-ft76 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug NutsTorque in star pattern100 lb-ft136 Nm
Front Suspension Rebuild4 specs
- Ball Joint Pinch BoltUse new bolt if locknut style37 lb-ft50 Nm
- Lower Control Arm BoltsTorque at ride height81 lb-ft110 Nm
- Strut Top Mount Nuts18 lb-ft25 Nm
- Sway Bar End Link Nuts44 lb-ft60 Nm
Knuckle/Spindle - Front7 specs
- Control Arm BoltsTorque with vehicle weight on wheels122 lb-ft165 Nm
- Lower Ball Joint NutUse new cotter pin81 lb-ft110 Nm
- Strut Bolts106 lb-ft144 Nm
- Strut Tower Nuts37 lb-ft50 Nm
- Sway Bar Link56 lb-ft76 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug NutsTorque in star pattern100 lb-ft136 Nm
Lateral Arm5 specs
- Control Arm BoltsTorque with vehicle weight on wheels122 lb-ft165 Nm
- Strut Bolts106 lb-ft144 Nm
- Sway Bar Link56 lb-ft76 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug NutsTorque in star pattern100 lb-ft136 Nm
Lower Control Arm - Front6 specs
- Control Arm BoltsTorque with vehicle weight on wheels122 lb-ft165 Nm
- Lower Ball Joint Nut81 lb-ft110 Nm
- Strut Bolts106 lb-ft144 Nm
- Sway Bar Link56 lb-ft76 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug Nuts100 lb-ft136 Nm
Lower Control Arm - Rear4 specs
- Control Arm BoltsTorque with vehicle weight on wheels122 lb-ft165 Nm
- Sway Bar Link56 lb-ft76 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug NutsTorque in star pattern100 lb-ft136 Nm
Panhard Bar/Track Bar3 specs
- Strut Bolts106 lb-ft144 Nm
- Sway Bar Link56 lb-ft76 Nm
- Wheel Lug Nuts100 lb-ft136 Nm
Radius Arm5 specs
- Control Arm BoltsTorque with vehicle weight on wheels122 lb-ft165 Nm
- Strut Bolts106 lb-ft144 Nm
- Sway Bar Link56 lb-ft76 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug Nuts100 lb-ft136 Nm
Radius Arm Bushing5 specs
- Control Arm BoltsTorque with vehicle weight on wheels122 lb-ft165 Nm
- Strut Bolts106 lb-ft144 Nm
- Sway Bar Link56 lb-ft76 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug Nuts100 lb-ft136 Nm
Rear Shocks - Pair3 specs
- Sway Bar Link56 lb-ft76 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug NutsTorque in star pattern100 lb-ft136 Nm
Rear Suspension Service4 specs
- Lower Control Arm BoltsTorque at ride height66 lb-ft90 Nm
- Shock Lower Bolt52 lb-ft70 Nm
- Sway Bar End Link Nuts37 lb-ft50 Nm
- Trailing Arm BoltsTorque at ride height88 lb-ft120 Nm
Shock Absorber Replacement2 specs
- Lower Mount Bolt66 lb-ft90 Nm
- Upper Mount NutUse new self-locking nut41 lb-ft55 Nm
Strut Assembly - Front4 specs
- Strut Mount Center NutHold strut shaft with Allen key41 lb-ft55 Nm
- Strut to Knuckle BoltsOften TTY111 lb-ft150 Nm
- Strut Tower NutsDo not loosen center nut unless compressed37 lb-ft50 Nm
- Sway Bar End Link Nuts41 lb-ft55 Nm
Strut Bearing6 specs
- Strut Bolts106 lb-ft144 Nm
- Strut to Knuckle Bolts113 lb-ft153 Nm
- Strut Tower Nuts37 lb-ft50 Nm
- Sway Bar Link56 lb-ft76 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug Nuts100 lb-ft136 Nm
Strut Mount - Front6 specs
- Strut Bolts106 lb-ft144 Nm
- Strut to Knuckle Bolts113 lb-ft153 Nm
- Strut Tower Nuts37 lb-ft50 Nm
- Sway Bar Link56 lb-ft76 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug NutsTorque in star pattern100 lb-ft136 Nm
Subframe6 specs
- Control Arm BoltsTorque with vehicle weight on wheels122 lb-ft165 Nm
- Strut Bolts106 lb-ft144 Nm
- Strut Tower Nuts37 lb-ft50 Nm
- Sway Bar Link56 lb-ft76 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug Nuts100 lb-ft136 Nm
Subframe Bushing6 specs
- Control Arm BoltsTorque with vehicle weight on wheels122 lb-ft165 Nm
- Strut Bolts106 lb-ft144 Nm
- Strut Tower Nuts37 lb-ft50 Nm
- Sway Bar Link56 lb-ft76 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug Nuts100 lb-ft136 Nm
Sway Bar - Front5 specs
- Strut Bolts106 lb-ft144 Nm
- Sway Bar Bracket Bolts44 lb-ft59 Nm
- Sway Bar Link56 lb-ft76 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug NutsTorque in star pattern100 lb-ft136 Nm
Sway Bar - Rear4 specs
- Sway Bar Bracket Bolts44 lb-ft59 Nm
- Sway Bar Link56 lb-ft76 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug NutsTorque in star pattern100 lb-ft136 Nm
Sway Bar Bushing - Front5 specs
- Strut Bolts106 lb-ft144 Nm
- Sway Bar Bracket Bolts44 lb-ft59 Nm
- Sway Bar Link56 lb-ft76 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug NutsTorque in star pattern100 lb-ft136 Nm
Sway Bar Bushing - Rear4 specs
- Sway Bar Bracket Bolts44 lb-ft59 Nm
- Sway Bar Link56 lb-ft76 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug NutsTorque in star pattern100 lb-ft136 Nm
Sway Bar Link - Front5 specs
- Strut Bolts106 lb-ft144 Nm
- Sway Bar Bracket Bolts44 lb-ft59 Nm
- Sway Bar Link56 lb-ft76 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug NutsTorque in star pattern100 lb-ft136 Nm
Sway Bar Link - Rear4 specs
- Sway Bar Bracket Bolts44 lb-ft59 Nm
- Sway Bar Link56 lb-ft76 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug NutsTorque in star pattern100 lb-ft136 Nm
Sway Bar Links - Front Pair5 specs
- Strut Bolts106 lb-ft144 Nm
- Sway Bar Bracket Bolts44 lb-ft59 Nm
- Sway Bar Link56 lb-ft76 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug NutsTorque in star pattern100 lb-ft136 Nm
Trailing Arm5 specs
- Control Arm BoltsTorque with vehicle weight on wheels122 lb-ft165 Nm
- Strut Bolts106 lb-ft144 Nm
- Sway Bar Link56 lb-ft76 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug Nuts100 lb-ft136 Nm
Trailing Arm Bushing5 specs
- Control Arm BoltsTorque with vehicle weight on wheels122 lb-ft165 Nm
- Strut Bolts106 lb-ft144 Nm
- Sway Bar Link56 lb-ft76 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug NutsTorque in star pattern100 lb-ft136 Nm
Upper Control Arm - Rear3 specs
- Control Arm BoltsTorque with vehicle weight on wheels122 lb-ft165 Nm
- Sway Bar Link56 lb-ft76 Nm
- Wheel Lug NutsTorque in star pattern100 lb-ft136 Nm
Steering
Power Steering Fluid Flush7 specs
- Coupling Bolt31 lb-ft42 Nm
- Power Steering Line FittingsUse new O-rings22 lb-ft30 Nm
- Steering Rack Bolts74 lb-ft100 Nm
- Tie Rod End Castle NutUse new cotter pin41 lb-ft55 Nm
- Tie Rod End NutUse new cotter pin50 lb-ft68 Nm
- Tie Rod Nut50 lb-ft68 Nm
- Wheel Lug Nuts100 lb-ft136 Nm
Power Steering Hose - High Pressure6 specs
- Coupling Bolt31 lb-ft42 Nm
- Power Steering Line FittingsUse new O-rings22 lb-ft30 Nm
- Steering Rack Bolts74 lb-ft100 Nm
- Tie Rod End NutUse new cotter pin50 lb-ft68 Nm
- Tie Rod Nut50 lb-ft68 Nm
- Wheel Lug Nuts100 lb-ft136 Nm
Power Steering Hose - Return6 specs
- Coupling Bolt31 lb-ft42 Nm
- Power Steering Line FittingsUse new O-rings22 lb-ft30 Nm
- Steering Rack Bolts74 lb-ft100 Nm
- Tie Rod End NutUse new cotter pin50 lb-ft68 Nm
- Tie Rod Nut50 lb-ft68 Nm
- Wheel Lug Nuts100 lb-ft136 Nm
Power Steering Pump8 specs
- High Pressure Hose FittingUse new O-rings18 lb-ft25 Nm
- Power Steering Pump Bolts18 lb-ft25 Nm
- Pressure Line FittingUse new O-rings22 lb-ft30 Nm
- Pulley NutHold pulley with pin spanner52 lb-ft70 Nm
- Pump Mounting Bolts18 lb-ft25 Nm
- Return Hose Clamp2 lb-ft3 Nm
- Return Line Clamp3 lb-ft4 Nm
- Serpentine Belt Tensioner41 lb-ft55 Nm
Power Steering Pump Pulley6 specs
- Coupling Bolt31 lb-ft42 Nm
- Pressure Line FittingNew O-ring31 lb-ft42 Nm
- Pump Mounting Bolts25 lb-ft34 Nm
- Tie Rod End NutUse new cotter pin50 lb-ft68 Nm
- Tie Rod Nut50 lb-ft68 Nm
- Wheel Lug Nuts100 lb-ft136 Nm
Power Steering Rack9 specs
- Coupling Bolt31 lb-ft42 Nm
- Power Steering Line FittingsUse new O-rings. Verify sequence with the service manual22 lb-ft30 Nm
- Pressure Line FittingNew O-ring31 lb-ft42 Nm
- Pump Mounting Bolts25 lb-ft34 Nm
- Steering Rack BoltsVerify sequence with the service manual74 lb-ft100 Nm
- Tie Rod End Castle NutUse new cotter pin. Verify sequence with the service manual41 lb-ft55 Nm
- Tie Rod End NutUse new cotter pin50 lb-ft68 Nm
- Tie Rod Nut50 lb-ft68 Nm
- Wheel Lug Nuts100 lb-ft136 Nm
Power Steering Reservoir5 specs
- Coupling Bolt31 lb-ft42 Nm
- Power Steering Line FittingsUse new O-rings22 lb-ft30 Nm
- Tie Rod End NutUse new cotter pin50 lb-ft68 Nm
- Tie Rod Nut50 lb-ft68 Nm
- Wheel Lug Nuts100 lb-ft136 Nm
Rack and Pinion Boots5 specs
- Coupling Bolt31 lb-ft42 Nm
- Tie Rod End Castle NutUse new cotter pin41 lb-ft55 Nm
- Tie Rod End NutUse new cotter pin50 lb-ft68 Nm
- Tie Rod Nut50 lb-ft68 Nm
- Wheel Lug Nuts100 lb-ft136 Nm
Steering Angle Sensor4 specs
- Coupling Bolt31 lb-ft42 Nm
- Tie Rod End NutUse new cotter pin50 lb-ft68 Nm
- Tie Rod Nut50 lb-ft68 Nm
- Wheel Lug Nuts100 lb-ft136 Nm
Steering Column9 specs
- Coupling Bolt31 lb-ft42 Nm
- Ignition Switch BoltsVerify sequence with the service manual4 lb-ft5 Nm
- Pinch BoltVerify sequence with the service manual22 lb-ft30 Nm
- Power Steering Line FittingsUse new O-rings31 lb-ft42 Nm
- Steering Column BoltsVerify sequence with the service manual22 lb-ft30 Nm
- Steering Rack Bolts94 lb-ft127 Nm
- Tie Rod End NutUse new cotter pin50 lb-ft68 Nm
- Tie Rod Nut50 lb-ft68 Nm
- Wheel Lug Nuts100 lb-ft136 Nm
Steering Coupler5 specs
- Coupling Bolt31 lb-ft42 Nm
- Steering Rack BoltsVerify sequence with the service manual74 lb-ft100 Nm
- Tie Rod End NutUse new cotter pin50 lb-ft68 Nm
- Tie Rod Nut50 lb-ft68 Nm
- Wheel Lug Nuts100 lb-ft136 Nm
Steering Damper4 specs
- Coupling Bolt31 lb-ft42 Nm
- Tie Rod End NutUse new cotter pin50 lb-ft68 Nm
- Tie Rod Nut50 lb-ft68 Nm
- Wheel Lug Nuts100 lb-ft136 Nm
Steering Shaft - Intermediate5 specs
- Coupling Bolt31 lb-ft42 Nm
- Steering Rack BoltsVerify sequence with the service manual74 lb-ft100 Nm
- Tie Rod End NutUse new cotter pin50 lb-ft68 Nm
- Tie Rod Nut50 lb-ft68 Nm
- Wheel Lug Nuts100 lb-ft136 Nm
Steering Shaft - Upper4 specs
- Coupling Bolt31 lb-ft42 Nm
- Tie Rod End NutUse new cotter pin50 lb-ft68 Nm
- Tie Rod Nut50 lb-ft68 Nm
- Wheel Lug Nuts100 lb-ft136 Nm
Steering Wheel8 specs
- Airbag Module BoltsTorx - usually T30. Verify sequence with the service manual5 lb-ft7 Nm
- Coupling Bolt31 lb-ft42 Nm
- Power Steering Line FittingsUse new O-rings31 lb-ft42 Nm
- Steering Rack Bolts94 lb-ft127 Nm
- Steering Wheel NutVerify sequence with the service manual40 lb-ft54 Nm
- Tie Rod End NutUse new cotter pin50 lb-ft68 Nm
- Tie Rod Nut50 lb-ft68 Nm
- Wheel Lug Nuts100 lb-ft136 Nm
Tie Rod Assembly6 specs
- Coupling Bolt31 lb-ft42 Nm
- Tie Rod End Castle NutUse new cotter pin41 lb-ft55 Nm
- Tie Rod End NutNew cotter pin50 lb-ft68 Nm
- Tie Rod Lock NutAfter alignment63 lb-ft85 Nm
- Tie Rod Nut50 lb-ft68 Nm
- Wheel Lug Nuts100 lb-ft136 Nm
Tie Rod End - Inner7 specs
- Coupling Bolt31 lb-ft42 Nm
- Steering Rack Bolts74 lb-ft100 Nm
- Tie Rod End Castle NutUse new cotter pin41 lb-ft55 Nm
- Tie Rod End NutNew cotter pin50 lb-ft68 Nm
- Tie Rod Lock NutAfter alignment63 lb-ft85 Nm
- Tie Rod Nut50 lb-ft68 Nm
- Wheel Lug Nuts100 lb-ft136 Nm
Tie Rod End - Outer6 specs
- Coupling Bolt31 lb-ft42 Nm
- Tie Rod End Castle NutUse new cotter pin41 lb-ft55 Nm
- Tie Rod End NutNew cotter pin50 lb-ft68 Nm
- Tie Rod Lock NutAfter alignment63 lb-ft85 Nm
- Tie Rod Nut50 lb-ft68 Nm
- Wheel Lug Nuts100 lb-ft136 Nm
Tie Rods - Both Sides6 specs
- Coupling Bolt31 lb-ft42 Nm
- Tie Rod End Castle NutUse new cotter pin41 lb-ft55 Nm
- Tie Rod End NutNew cotter pin50 lb-ft68 Nm
- Tie Rod Lock NutAfter alignment63 lb-ft85 Nm
- Tie Rod Nut50 lb-ft68 Nm
- Wheel Lug Nuts100 lb-ft136 Nm
Drivetrain
Axle Seal - Front1 spec
- Wheel Lug NutsTorque in star pattern105 lb-ft142.4 Nm
Axle Seal - Rear5 specs
- CV Bolts56 lb-ft76 Nm
- CV Joint Bolts56 lb-ft76 Nm
- Differential Cover Bolts26 lb-ft35 Nm
- Driveshaft Bolts69 lb-ft94 Nm
- Wheel Lug NutsTorque in star pattern105 lb-ft142.4 Nm
CV Axle - Rear5 specs
- CV Bolts56 lb-ft76 Nm
- CV Joint Bolts56 lb-ft76 Nm
- Differential Cover BoltsApply RTV sealant31 lb-ft42 Nm
- Driveshaft Bolts69 lb-ft94 Nm
- Wheel Lug Nuts100 lb-ft136 Nm
CV Boot - Inner5 specs
- Axle NutUse new cotter pin or stake nut184 lb-ft250 Nm
- CV Bolts56 lb-ft76 Nm
- CV Joint Bolts56 lb-ft76 Nm
- Driveshaft Bolts69 lb-ft94 Nm
- Wheel Lug NutsTorque in star pattern105 lb-ft142.4 Nm
CV Boot - Outer5 specs
- Axle NutUse new cotter pin or stake nut184 lb-ft250 Nm
- CV Bolts56 lb-ft76 Nm
- CV Joint Bolts56 lb-ft76 Nm
- Driveshaft Bolts69 lb-ft94 Nm
- Wheel Lug NutsTorque in star pattern105 lb-ft142.4 Nm
Differential Cover Gasket5 specs
- CV Bolts56 lb-ft76 Nm
- CV Joint Bolts56 lb-ft76 Nm
- Differential Cover Bolts26 lb-ft35 Nm
- Driveshaft Bolts69 lb-ft94 Nm
- Wheel Lug NutsTorque in star pattern105 lb-ft142.4 Nm
Differential Fluid Change - Rear5 specs
- CV Bolts56 lb-ft76 Nm
- CV Joint Bolts56 lb-ft76 Nm
- Differential Cover Bolts26 lb-ft35 Nm
- Driveshaft Bolts69 lb-ft94 Nm
- Wheel Lug NutsTorque in star pattern105 lb-ft142.4 Nm
Differential Pinion Seal6 specs
- CV Bolts56 lb-ft76 Nm
- CV Joint Bolts56 lb-ft76 Nm
- Differential Cover Bolts26 lb-ft35 Nm
- Driveshaft Bolts69 lb-ft94 Nm
- Driveshaft U-Joint StrapsTighten evenly15 lb-ft20 Nm
- Wheel Lug NutsTorque in star pattern105 lb-ft142.4 Nm
Differential Rebuild - Rear8 specs
- CV Bolts56 lb-ft76 Nm
- CV Joint Bolts56 lb-ft76 Nm
- Differential Cover Bolts26 lb-ft35 Nm
- Drain PlugNew washer38 lb-ft51 Nm
- Driveshaft Bolts69 lb-ft94 Nm
- Driveshaft U-Joint StrapsTighten evenly15 lb-ft20 Nm
- Fill Plug38 lb-ft51 Nm
- Wheel Lug NutsTorque in star pattern105 lb-ft142.4 Nm
Driveshaft - Rear3 specs
- Differential Pinion Yoke NutUse new nut, set pinion preload184 lb-ft250 Nm
- Driveshaft Flange Bolts55 lb-ft75 Nm
- U-Joint Strap BoltsApply threadlocker26 lb-ft35 Nm
Driveshaft Center Support Bearing2 specs
- Center Support Bearing Bracket Bolts37 lb-ft50 Nm
- Driveshaft Flange Bolts55 lb-ft75 Nm
Limited Slip Clutch Pack7 specs
- Axle NutUse new cotter pin or stake nut184 lb-ft250 Nm
- CV Bolts56 lb-ft76 Nm
- CV Joint Bolts56 lb-ft76 Nm
- Differential Cover Bolts26 lb-ft35 Nm
- Driveshaft Bolts69 lb-ft94 Nm
- Driveshaft U-Joint StrapsTighten evenly15 lb-ft20 Nm
- Wheel Lug NutsTorque in star pattern105 lb-ft142.4 Nm
Rear Differential1 spec
- Wheel Lug NutsTorque in star pattern105 lb-ft142.4 Nm
Ring and Pinion7 specs
- Axle NutUse new cotter pin or stake nut184 lb-ft250 Nm
- CV Bolts56 lb-ft76 Nm
- CV Joint Bolts56 lb-ft76 Nm
- Differential Cover Bolts26 lb-ft35 Nm
- Driveshaft Bolts69 lb-ft94 Nm
- Driveshaft U-Joint StrapsTighten evenly15 lb-ft20 Nm
- Wheel Lug NutsTorque in star pattern105 lb-ft142.4 Nm
U-Joint8 specs
- Axle NutUse new nut, stake after225 lb-ft305 Nm
- CV Bolts56 lb-ft76 Nm
- CV Joint Bolts56 lb-ft76 Nm
- Differential Cover BoltsApply RTV sealant31 lb-ft42 Nm
- Driveshaft Bolts69 lb-ft94 Nm
- Driveshaft U-Joint StrapsTighten evenly15 lb-ft20 Nm
- Wheel Lug Nuts100 lb-ft136 Nm
- Yoke NutIf equipped111 lb-ft150 Nm
Wheel Bearing - Press-In Front6 specs
- ABS Sensor Bolt10 lb-ft14 Nm
- Axle NutUse new cotter pin or stake nut184 lb-ft250 Nm
- CV Joint Bolts56 lb-ft76 Nm
- Driveshaft Bolts69 lb-ft94 Nm
- Hub Bolts94 lb-ft127 Nm
- Wheel Lug NutsTorque in star pattern105 lb-ft142.4 Nm
Wheel Bearing - Press-In Rear6 specs
- ABS Sensor Bolt10 lb-ft14 Nm
- CV Joint Bolts56 lb-ft76 Nm
- Differential Cover Bolts26 lb-ft35 Nm
- Driveshaft Bolts69 lb-ft94 Nm
- Hub Bolts94 lb-ft127 Nm
- Wheel Lug NutsTorque in star pattern105 lb-ft142.4 Nm
Wheel Bearing Hub - Front4 specs
- ABS Sensor BoltDo not overtighten7 lb-ft10 Nm
- Axle NutUse new cotter pin after torque184 lb-ft250 Nm
- Caliper Bracket Bolts88 lb-ft120 Nm
- Wheel Bearing Hub BoltsApply threadlocker if specified81 lb-ft110 Nm
Wheel Bearing Hub - Rear2 specs
- Caliper Bracket Bolts81 lb-ft110 Nm
- Wheel Bearing Hub BoltsApply threadlocker if specified74 lb-ft100 Nm
Wheel Studs5 specs
- Axle NutUse new cotter pin or stake nut184 lb-ft250 Nm
- CV Bolts56 lb-ft76 Nm
- CV Joint Bolts56 lb-ft76 Nm
- Driveshaft Bolts69 lb-ft94 Nm
- Wheel Lug NutsTorque in star pattern105 lb-ft142.4 Nm
Transmission
Clutch Cable4 specs
- Bell Housing Bolts44 lb-ft59 Nm
- Drain PlugUse new washer31 lb-ft42 Nm
- Fill Plug31 lb-ft42 Nm
- Pressure Plate BoltStar pattern25 lb-ft34 Nm
Clutch Disc6 specs
- Bell Housing Bolts44 lb-ft59 Nm
- Drain PlugUse new washer31 lb-ft42 Nm
- Fill Plug31 lb-ft42 Nm
- Flywheel BoltsOften TTY, tighten in star pattern70 lb-ft95 Nm
- Pressure Plate BoltStar pattern25 lb-ft34 Nm
- Transmission Drain PlugUse new crush washer if equipped22 lb-ft30 Nm
Clutch Hydraulic Line4 specs
- Bell Housing Bolts44 lb-ft59 Nm
- Drain PlugUse new washer31 lb-ft42 Nm
- Fill Plug31 lb-ft42 Nm
- Pressure Plate BoltStar pattern25 lb-ft34 Nm
Clutch Kit6 specs
- Bell Housing Bolts44 lb-ft59 Nm
- Drain PlugUse new washer31 lb-ft42 Nm
- Fill Plug31 lb-ft42 Nm
- Flywheel BoltsOften TTY, tighten in star pattern70 lb-ft95 Nm
- Pressure Plate BoltStar pattern25 lb-ft34 Nm
- Transmission Drain PlugUse new crush washer if equipped22 lb-ft30 Nm
Clutch Master Cylinder7 specs
- Bell Housing Bolts44 lb-ft59 Nm
- Drain PlugUse new washer31 lb-ft42 Nm
- Fill Plug31 lb-ft42 Nm
- Flywheel BoltsThread locker70 lb-ft95 Nm
- Hydraulic Line11 lb-ft15 Nm
- Master Cylinder Bolts18 lb-ft25 Nm
- Pressure Plate BoltStar pattern25 lb-ft34 Nm
Clutch Slave Cylinder7 specs
- Bell Housing Bolts44 lb-ft59 Nm
- Drain PlugUse new washer31 lb-ft42 Nm
- Fill Plug31 lb-ft42 Nm
- Flywheel BoltsThread locker94 lb-ft127 Nm
- Hydraulic Line11 lb-ft15 Nm
- Pressure Plate BoltStar pattern25 lb-ft34 Nm
- Slave Cylinder Bolts18 lb-ft25 Nm
Dual Mass Flywheel4 specs
- Drain PlugUse new washer31 lb-ft42 Nm
- Fill Plug31 lb-ft42 Nm
- Flywheel BoltsOften TTY, tighten in star pattern70 lb-ft95 Nm
- Transmission Drain PlugUse new crush washer if equipped22 lb-ft30 Nm
Flywheel Resurface4 specs
- Drain PlugUse new washer31 lb-ft42 Nm
- Fill Plug31 lb-ft42 Nm
- Flywheel BoltsOften TTY, tighten in star pattern70 lb-ft95 Nm
- Transmission Drain PlugUse new crush washer if equipped22 lb-ft30 Nm
Manual Trans Fluid Change3 specs
- Drain PlugUse new washer31 lb-ft42 Nm
- Fill Plug31 lb-ft42 Nm
- Transmission Drain PlugUse new crush washer if equipped22 lb-ft30 Nm
Neutral Safety Switch3 specs
- Drain PlugUse new washer31 lb-ft42 Nm
- Fill Plug31 lb-ft42 Nm
- Switch Mounting Bolts11 lb-ft15 Nm
Overdrive Solenoid4 specs
- Drain PlugUse new washer31 lb-ft42 Nm
- Fill Plug31 lb-ft42 Nm
- Transmission Drain PlugUse new crush washer if equipped22 lb-ft30 Nm
- Transmission Pan BoltsTighten in criss-cross pattern9 lb-ft12 Nm
Pilot Bearing4 specs
- Drain PlugUse new washer31 lb-ft42 Nm
- Fill Plug31 lb-ft42 Nm
- Flywheel BoltsOften TTY, tighten in star pattern70 lb-ft95 Nm
- Transmission Drain PlugUse new crush washer if equipped22 lb-ft30 Nm
Pressure Plate4 specs
- Drain PlugUse new washer31 lb-ft42 Nm
- Fill Plug31 lb-ft42 Nm
- Flywheel BoltsOften TTY, tighten in star pattern70 lb-ft95 Nm
- Transmission Drain PlugUse new crush washer if equipped22 lb-ft30 Nm
Shift Cable4 specs
- Adjustment Nut7 lb-ft10 Nm
- Cable Bracket Bolts11 lb-ft15 Nm
- Drain PlugUse new washer31 lb-ft42 Nm
- Fill Plug31 lb-ft42 Nm
Shift Fork3 specs
- Drain PlugUse new washer31 lb-ft42 Nm
- Fill Plug31 lb-ft42 Nm
- Transmission Drain PlugUse new crush washer if equipped22 lb-ft30 Nm
Shift Linkage4 specs
- Drain PlugUse new washer31 lb-ft42 Nm
- Fill Plug31 lb-ft42 Nm
- Linkage Bolts11 lb-ft15 Nm
- Pivot Bolts9 lb-ft12 Nm
Shift Solenoid - Single4 specs
- Drain PlugUse new washer31 lb-ft42 Nm
- Fill Plug31 lb-ft42 Nm
- Transmission Drain PlugUse new crush washer if equipped22 lb-ft30 Nm
- Transmission Pan BoltsTighten in criss-cross pattern9 lb-ft12 Nm
Shift Solenoids - All4 specs
- Drain PlugUse new washer31 lb-ft42 Nm
- Fill Plug31 lb-ft42 Nm
- Transmission Drain PlugUse new crush washer if equipped22 lb-ft30 Nm
- Transmission Pan BoltsTighten in criss-cross pattern9 lb-ft12 Nm
Synchros - All4 specs
- Drain PlugUse new washer31 lb-ft42 Nm
- Fill Plug31 lb-ft42 Nm
- Transmission Drain PlugUse new crush washer if equipped22 lb-ft30 Nm
- Transmission Pan BoltsTighten in criss-cross pattern9 lb-ft12 Nm
Synchros - Single Gear3 specs
- Drain PlugUse new washer31 lb-ft42 Nm
- Fill Plug31 lb-ft42 Nm
- Transmission Drain PlugUse new crush washer if equipped22 lb-ft30 Nm
Throw-Out Bearing3 specs
- Drain PlugUse new washer31 lb-ft42 Nm
- Fill Plug31 lb-ft42 Nm
- Transmission Drain PlugUse new crush washer if equipped22 lb-ft30 Nm
Transmission Control Module4 specs
- Drain PlugUse new washer31 lb-ft42 Nm
- Fill Plug31 lb-ft42 Nm
- Transmission Drain PlugUse new crush washer if equipped22 lb-ft30 Nm
- Transmission Pan BoltsTighten in criss-cross pattern9 lb-ft12 Nm
Transmission Cooler Lines2 specs
- Drain PlugUse new washer31 lb-ft42 Nm
- Fill Plug31 lb-ft42 Nm
Transmission Filter4 specs
- Drain PlugUse new washer31 lb-ft42 Nm
- Fill Plug31 lb-ft42 Nm
- Transmission Drain PlugUse new crush washer if equipped22 lb-ft30 Nm
- Transmission Pan BoltsTighten in criss-cross pattern9 lb-ft12 Nm
Transmission Filter and Fluid4 specs
- Drain PlugUse new washer31 lb-ft42 Nm
- Fill Plug31 lb-ft42 Nm
- Transmission Drain PlugUse new crush washer if equipped22 lb-ft30 Nm
- Transmission Pan BoltsTighten in criss-cross pattern9 lb-ft12 Nm
Transmission Fluid Change5 specs
- Drain PlugUse new washer31 lb-ft42 Nm
- Fill Plug31 lb-ft42 Nm
- Transmission Drain PlugUse new crush washer if equipped22 lb-ft30 Nm
- Transmission Filter BoltsIf equipped with bolted filter6 lb-ft8 Nm
- Transmission Pan BoltsTighten in criss-cross pattern9 lb-ft12 Nm
Transmission Flush4 specs
- Drain PlugUse new washer31 lb-ft42 Nm
- Fill Plug31 lb-ft42 Nm
- Transmission Drain PlugUse new crush washer if equipped22 lb-ft30 Nm
- Transmission Pan BoltsTighten in criss-cross pattern9 lb-ft12 Nm
Transmission Input Shaft Bearing5 specs
- Drain PlugUse new washer31 lb-ft42 Nm
- Fill Plug31 lb-ft42 Nm
- Flywheel BoltsOften TTY, tighten in star pattern70 lb-ft95 Nm
- Transmission Drain PlugUse new crush washer if equipped22 lb-ft30 Nm
- Transmission Pan BoltsTighten in criss-cross pattern9 lb-ft12 Nm
Transmission Oil Cooler9 specs
- Coolant Drain Plug11 lb-ft15 Nm
- Drain PetcockHand tight6 lb-ft8 Nm
- Drain PlugUse new washer31 lb-ft42 Nm
- Fan Bolts10 lb-ft14 Nm
- Fill Plug31 lb-ft42 Nm
- Hose Clamps2 lb-ft3 Nm
- Pump BoltsTorque in sequence22 lb-ft30 Nm
- Thermostat Housing Bolt11 lb-ft15 Nm
- Water Pump BoltsTighten in criss-cross pattern18 lb-ft25 Nm
Transmission Output Shaft Bearing5 specs
- Drain PlugUse new washer31 lb-ft42 Nm
- Fill Plug31 lb-ft42 Nm
- Flywheel BoltsOften TTY, tighten in star pattern70 lb-ft95 Nm
- Transmission Drain PlugUse new crush washer if equipped22 lb-ft30 Nm
- Transmission Pan BoltsTighten in criss-cross pattern9 lb-ft12 Nm
Transmission Pan Gasket4 specs
- Drain PlugUse new washer31 lb-ft42 Nm
- Fill Plug31 lb-ft42 Nm
- Transmission Drain PlugUse new crush washer if equipped22 lb-ft30 Nm
- Transmission Pan BoltsTighten in criss-cross pattern9 lb-ft12 Nm
Transmission R&R - Automatic5 specs
- Drain PlugUse new washer31 lb-ft42 Nm
- Fill Plug31 lb-ft42 Nm
- Flywheel BoltsOften TTY, tighten in star pattern70 lb-ft95 Nm
- Transmission Drain PlugUse new crush washer if equipped22 lb-ft30 Nm
- Transmission Pan BoltsTighten in criss-cross pattern9 lb-ft12 Nm
Transmission R&R - Manual4 specs
- Drain PlugUse new washer31 lb-ft42 Nm
- Fill Plug31 lb-ft42 Nm
- Flywheel BoltsOften TTY, tighten in star pattern70 lb-ft95 Nm
- Transmission Drain PlugUse new crush washer if equipped22 lb-ft30 Nm
Transmission Range Sensor4 specs
- Drain PlugUse new washer31 lb-ft42 Nm
- Fill Plug31 lb-ft42 Nm
- Transmission Drain PlugUse new crush washer if equipped22 lb-ft30 Nm
- Transmission Pan BoltsTighten in criss-cross pattern9 lb-ft12 Nm
Transmission Rebuild - Automatic5 specs
- Drain PlugUse new washer31 lb-ft42 Nm
- Fill Plug31 lb-ft42 Nm
- Flywheel BoltsOften TTY, tighten in star pattern70 lb-ft95 Nm
- Transmission Drain PlugUse new crush washer if equipped22 lb-ft30 Nm
- Transmission Pan BoltsTighten in criss-cross pattern9 lb-ft12 Nm
Transmission Rebuild - Manual5 specs
- Drain PlugUse new washer31 lb-ft42 Nm
- Fill Plug31 lb-ft42 Nm
- Flywheel BoltsOften TTY, tighten in star pattern70 lb-ft95 Nm
- Transmission Drain PlugUse new crush washer if equipped22 lb-ft30 Nm
- Transmission Pan BoltsTighten in criss-cross pattern9 lb-ft12 Nm
Transmission Speed Sensor - Input3 specs
- Drain PlugUse new washer31 lb-ft42 Nm
- Fill Plug31 lb-ft42 Nm
- Transmission Pan BoltsTighten in criss-cross pattern9 lb-ft12 Nm
Transmission Speed Sensor - Output2 specs
- Drain PlugUse new washer31 lb-ft42 Nm
- Fill Plug31 lb-ft42 Nm
Valve Body4 specs
- Drain PlugUse new washer31 lb-ft42 Nm
- Fill Plug31 lb-ft42 Nm
- Transmission Drain PlugUse new crush washer if equipped22 lb-ft30 Nm
- Transmission Pan BoltsTighten in criss-cross pattern9 lb-ft12 Nm
Exhaust
Air Injection Check Valve4 specs
- Exhaust Flange BoltApply anti-seize33 lb-ft45 Nm
- Hanger Bolts19 lb-ft25 Nm
- Heat Shield Bolts7 lb-ft10 Nm
- Manifold NutsApply anti-seize31 lb-ft42 Nm
Catalytic Converter - Direct Fit5 specs
- Exhaust Flange BoltApply anti-seize33 lb-ft45 Nm
- Hanger Bolts19 lb-ft25 Nm
- Heat Shield Bolts7 lb-ft10 Nm
- Manifold NutsApply anti-seize31 lb-ft42 Nm
- O2 SensorApply anti-seize to threads only33 lb-ft45 Nm
Catalytic Converter - Universal5 specs
- Exhaust Flange BoltApply anti-seize33 lb-ft45 Nm
- Hanger Bolts19 lb-ft25 Nm
- Heat Shield Bolts7 lb-ft10 Nm
- Manifold NutsApply anti-seize31 lb-ft42 Nm
- O2 SensorApply anti-seize to threads only33 lb-ft45 Nm
Downpipe5 specs
- Exhaust Flange BoltApply anti-seize33 lb-ft45 Nm
- Hanger Bolts19 lb-ft25 Nm
- Heat Shield Bolts7 lb-ft10 Nm
- Manifold NutsApply anti-seize31 lb-ft42 Nm
- O2 SensorApply anti-seize to threads only33 lb-ft45 Nm
EGR Tube4 specs
- Exhaust Flange BoltApply anti-seize33 lb-ft45 Nm
- Hanger Bolts19 lb-ft25 Nm
- Heat Shield Bolts7 lb-ft10 Nm
- Manifold NutsApply anti-seize31 lb-ft42 Nm
EGR Valve6 specs
- EGR Tube Fitting26 lb-ft35 Nm
- EGR Valve Bolts18 lb-ft25 Nm
- Hanger Bolts19 lb-ft25 Nm
- Heat Shield Bolts12 lb-ft16 Nm
- Manifold NutsApply anti-seize31 lb-ft42 Nm
- O2 Sensor44 lb-ft59 Nm
Exhaust Clamp4 specs
- Exhaust Flange BoltApply anti-seize33 lb-ft45 Nm
- Hanger Bolts19 lb-ft25 Nm
- Heat Shield Bolts7 lb-ft10 Nm
- Manifold NutsApply anti-seize31 lb-ft42 Nm
Exhaust Gasket - Front5 specs
- Exhaust Flange BoltApply anti-seize33 lb-ft45 Nm
- Hanger Bolts19 lb-ft25 Nm
- Heat Shield Bolts7 lb-ft10 Nm
- Manifold NutsApply anti-seize31 lb-ft42 Nm
- O2 SensorApply anti-seize to threads only33 lb-ft45 Nm
Exhaust Gasket - Rear4 specs
- Exhaust Flange BoltApply anti-seize33 lb-ft45 Nm
- Hanger Bolts19 lb-ft25 Nm
- Heat Shield Bolts7 lb-ft10 Nm
- Manifold NutsApply anti-seize31 lb-ft42 Nm
Exhaust Hangers4 specs
- Exhaust Flange BoltApply anti-seize33 lb-ft45 Nm
- Hanger Bolts19 lb-ft25 Nm
- Heat Shield Bolts7 lb-ft10 Nm
- Manifold NutsApply anti-seize31 lb-ft42 Nm
Exhaust Manifold Studs5 specs
- Exhaust Flange BoltApply anti-seize33 lb-ft45 Nm
- Hanger Bolts19 lb-ft25 Nm
- Heat Shield Bolts7 lb-ft10 Nm
- Manifold NutsApply anti-seize31 lb-ft42 Nm
- O2 SensorApply anti-seize to threads only33 lb-ft45 Nm
Exhaust Pipe - Rear Section4 specs
- Exhaust Flange BoltApply anti-seize33 lb-ft45 Nm
- Hanger Bolts19 lb-ft25 Nm
- Heat Shield Bolts7 lb-ft10 Nm
- Manifold NutsApply anti-seize31 lb-ft42 Nm
Exhaust Tip3 specs
- Exhaust Flange BoltApply anti-seize33 lb-ft45 Nm
- Hanger Bolts19 lb-ft25 Nm
- Manifold NutsApply anti-seize31 lb-ft42 Nm
Flex Pipe5 specs
- Exhaust Clamps41 lb-ft55 Nm
- Hanger Bolts19 lb-ft25 Nm
- Heat Shield Bolts12 lb-ft16 Nm
- Manifold NutsApply anti-seize31 lb-ft42 Nm
- O2 Sensor44 lb-ft59 Nm
Front Pipe5 specs
- Exhaust Flange BoltApply anti-seize33 lb-ft45 Nm
- Hanger Bolts19 lb-ft25 Nm
- Heat Shield Bolts7 lb-ft10 Nm
- Manifold NutsApply anti-seize31 lb-ft42 Nm
- O2 SensorApply anti-seize to threads only33 lb-ft45 Nm
Intermediate Pipe5 specs
- Exhaust Flange BoltApply anti-seize33 lb-ft45 Nm
- Hanger Bolts19 lb-ft25 Nm
- Heat Shield Bolts7 lb-ft10 Nm
- Manifold NutsApply anti-seize31 lb-ft42 Nm
- O2 SensorApply anti-seize to threads only33 lb-ft45 Nm
Muffler2 specs
- Hanger Bracket Bolts18 lb-ft25 Nm
- Muffler Clamps41 lb-ft55 Nm
O2 Sensor - Downstream5 specs
- Exhaust Flange BoltApply anti-seize33 lb-ft45 Nm
- Hanger Bolts19 lb-ft25 Nm
- Heat Shield Bolts7 lb-ft10 Nm
- Manifold NutsApply anti-seize31 lb-ft42 Nm
- O2 SensorApply anti-seize to threads only33 lb-ft45 Nm
O2 Sensor - Upstream5 specs
- Exhaust Flange BoltApply anti-seize33 lb-ft45 Nm
- Hanger Bolts19 lb-ft25 Nm
- Heat Shield Bolts7 lb-ft10 Nm
- Manifold NutsApply anti-seize31 lb-ft42 Nm
- O2 SensorApply anti-seize to threads only33 lb-ft45 Nm
O2 Sensors - All5 specs
- Exhaust Flange BoltApply anti-seize33 lb-ft45 Nm
- Hanger Bolts19 lb-ft25 Nm
- Heat Shield Bolts7 lb-ft10 Nm
- Manifold NutsApply anti-seize31 lb-ft42 Nm
- O2 SensorApply anti-seize to threads only33 lb-ft45 Nm
Resonator5 specs
- Exhaust Clamps41 lb-ft55 Nm
- Hanger Bolts19 lb-ft25 Nm
- Heat Shield Bolts12 lb-ft16 Nm
- Manifold NutsApply anti-seize31 lb-ft42 Nm
- O2 Sensor44 lb-ft59 Nm
Secondary Air Injection Pump4 specs
- Exhaust Flange BoltApply anti-seize33 lb-ft45 Nm
- Hanger Bolts19 lb-ft25 Nm
- Heat Shield Bolts7 lb-ft10 Nm
- Manifold NutsApply anti-seize31 lb-ft42 Nm
Tail Pipe4 specs
- Exhaust Flange BoltApply anti-seize33 lb-ft45 Nm
- Hanger Bolts19 lb-ft25 Nm
- Heat Shield Bolts7 lb-ft10 Nm
- Manifold NutsApply anti-seize31 lb-ft42 Nm
Heating and A/C
AC Accumulator5 specs
- AC Line FittingsUse new O-rings, add PAG oil15 lb-ft20 Nm
- Blower Motor Mounting Screw3 lb-ft4 Nm
- Compressor Bolts31 lb-ft42 Nm
- Duct Clips2 lb-ft3 Nm
- Mounting Bracket Bolts22 lb-ft30 Nm
AC Clutch Coil4 specs
- Blower Motor Mounting Screw3 lb-ft4 Nm
- Compressor Bolts31 lb-ft42 Nm
- Duct Clips2 lb-ft3 Nm
- Mounting Bracket Bolts22 lb-ft30 Nm
AC Compressor3 specs
- AC Compressor Bolts18 lb-ft25 Nm
- AC Line FittingsUse new O-rings, add PAG oil15 lb-ft20 Nm
- Clutch Connector Bolt6 lb-ft8 Nm
AC Compressor Clutch4 specs
- Blower Motor Mounting Screw3 lb-ft4 Nm
- Compressor Bolts31 lb-ft42 Nm
- Duct Clips2 lb-ft3 Nm
- Mounting Bracket Bolts22 lb-ft30 Nm
AC Compressor Oil Add5 specs
- AC Line FittingsUse new O-rings, add PAG oil15 lb-ft20 Nm
- Blower Motor Mounting Screw3 lb-ft4 Nm
- Compressor Bolts31 lb-ft42 Nm
- Duct Clips2 lb-ft3 Nm
- Mounting Bracket Bolts22 lb-ft30 Nm
AC Condenser2 specs
- AC Line FittingsUse new O-rings15 lb-ft20 Nm
- Condenser Mounting Bolts9 lb-ft12 Nm
AC Evaporator7 specs
- AC Line FittingsUse new O-rings, add PAG oil15 lb-ft20 Nm
- Blower Motor Mounting Screw6 lb-ft8 Nm
- Compressor Bolts31 lb-ft42 Nm
- Duct Clips2 lb-ft3 Nm
- Evaporator Case Screws4 lb-ft5 Nm
- Expansion Valve7 lb-ft10 Nm
- Mounting Bracket Bolts22 lb-ft30 Nm
AC Expansion Valve (TXV)6 specs
- AC Line FittingsUse new O-rings, add PAG oil15 lb-ft20 Nm
- Blower Motor Mounting Screw6 lb-ft8 Nm
- Compressor Bolts31 lb-ft42 Nm
- Duct Clips2 lb-ft3 Nm
- Expansion Valve7 lb-ft10 Nm
- Mounting Bracket Bolts22 lb-ft30 Nm
AC High Pressure Switch5 specs
- AC Line FittingsUse new O-rings, add PAG oil15 lb-ft20 Nm
- Blower Motor Mounting Screw3 lb-ft4 Nm
- Compressor Bolts31 lb-ft42 Nm
- Duct Clips2 lb-ft3 Nm
- Mounting Bracket Bolts22 lb-ft30 Nm
AC Hose - High Side5 specs
- AC Line FittingsUse new O-rings, add PAG oil15 lb-ft20 Nm
- Blower Motor Mounting Screw3 lb-ft4 Nm
- Compressor Bolts31 lb-ft42 Nm
- Duct Clips2 lb-ft3 Nm
- Mounting Bracket Bolts22 lb-ft30 Nm
AC Hose - Low Side6 specs
- AC Line FittingsUse new O-rings, add PAG oil15 lb-ft20 Nm
- Blower Motor Mounting Screw3 lb-ft4 Nm
- Compressor Bolts31 lb-ft42 Nm
- Duct Clips2 lb-ft3 Nm
- Hose Clamps2 lb-ft3 Nm
- Mounting Bracket Bolts22 lb-ft30 Nm
AC Hose Assembly6 specs
- AC Line FittingsUse new O-rings, add PAG oil15 lb-ft20 Nm
- Blower Motor Mounting Screw3 lb-ft4 Nm
- Compressor Bolts31 lb-ft42 Nm
- Duct Clips2 lb-ft3 Nm
- Hose Clamps2 lb-ft3 Nm
- Mounting Bracket Bolts22 lb-ft30 Nm
AC Low Pressure Switch5 specs
- AC Line FittingsUse new O-rings, add PAG oil15 lb-ft20 Nm
- Blower Motor Mounting Screw3 lb-ft4 Nm
- Compressor Bolts31 lb-ft42 Nm
- Duct Clips2 lb-ft3 Nm
- Mounting Bracket Bolts22 lb-ft30 Nm
AC Orifice Tube5 specs
- AC Line FittingsUse new O-rings, add PAG oil15 lb-ft20 Nm
- Blower Motor Mounting Screw3 lb-ft4 Nm
- Compressor Bolts31 lb-ft42 Nm
- Duct Clips2 lb-ft3 Nm
- Mounting Bracket Bolts22 lb-ft30 Nm
AC Pressure Sensor5 specs
- AC Line FittingsUse new O-rings, add PAG oil15 lb-ft20 Nm
- Blower Motor Mounting Screw3 lb-ft4 Nm
- Compressor Bolts31 lb-ft42 Nm
- Duct Clips2 lb-ft3 Nm
- Mounting Bracket Bolts22 lb-ft30 Nm
AC Receiver/Drier6 specs
- AC Line FittingsUse new O-rings, add PAG oil15 lb-ft20 Nm
- Blower Motor Mounting Screw6 lb-ft8 Nm
- Compressor Bolts31 lb-ft42 Nm
- Duct Clips2 lb-ft3 Nm
- Mounting Bracket Bolts22 lb-ft30 Nm
- Receiver Drier Bolts7 lb-ft10 Nm
AC Recharge4 specs
- Blower Motor Mounting Screw3 lb-ft4 Nm
- Compressor Bolts31 lb-ft42 Nm
- Duct Clips2 lb-ft3 Nm
- Mounting Bracket Bolts22 lb-ft30 Nm
Blend Door Actuator5 specs
- Actuator Screws2 lb-ft3 Nm
- Blower Motor Mounting Screw6 lb-ft8 Nm
- Compressor Bolts31 lb-ft42 Nm
- Duct Clips2 lb-ft3 Nm
- Mounting Bracket Bolts22 lb-ft30 Nm
Cabin Air Filter4 specs
- Compressor Bolts31 lb-ft42 Nm
- Connector Bolts6 lb-ft8 Nm
- Filter Cover ClipsTool-free on most2 lb-ft3 Nm
- Glove Box Screws4 lb-ft5 Nm
Climate Control Module4 specs
- Blower Motor Mounting Screw3 lb-ft4 Nm
- Compressor Bolts31 lb-ft42 Nm
- Duct Clips2 lb-ft3 Nm
- Mounting Bracket Bolts22 lb-ft30 Nm
HVAC Control Panel4 specs
- Blower Motor Mounting Screw3 lb-ft4 Nm
- Compressor Bolts31 lb-ft42 Nm
- Duct Clips2 lb-ft3 Nm
- Mounting Bracket Bolts22 lb-ft30 Nm
Mode Door Actuator4 specs
- Blower Motor Mounting Screw3 lb-ft4 Nm
- Compressor Bolts31 lb-ft42 Nm
- Duct Clips2 lb-ft3 Nm
- Mounting Bracket Bolts22 lb-ft30 Nm
Recirculation Door Actuator4 specs
- Blower Motor Mounting Screw3 lb-ft4 Nm
- Compressor Bolts31 lb-ft42 Nm
- Duct Clips2 lb-ft3 Nm
- Mounting Bracket Bolts22 lb-ft30 Nm
Body
Bumper Cover - Front8 specs
- Bumper Cover Bolts7 lb-ft10 Nm
- Fender Liner Screws2 lb-ft3 Nm
- Grille Clips4 lb-ft5 Nm
- Hinge Bolts25 lb-ft34 Nm
- Latch Bolts12 lb-ft16 Nm
- Panel Bolts12 lb-ft16 Nm
- Striker Bolts31 lb-ft42 Nm
- Trim ClipsReplace if broken2 lb-ft3 Nm
Bumper Cover - Rear7 specs
- Bumper Cover Bolts7 lb-ft10 Nm
- Hinge Bolts25 lb-ft34 Nm
- Latch Bolts12 lb-ft16 Nm
- Panel Bolts12 lb-ft16 Nm
- Striker Bolts31 lb-ft42 Nm
- Trim ClipsReplace if broken2 lb-ft3 Nm
- Trunk Liner Screws2 lb-ft3 Nm
Bumper Reinforcement - Front7 specs
- Body Panel Bolts18 lb-ft25 Nm
- Bumper Cover Bolts7 lb-ft10 Nm
- Hinge Bolts25 lb-ft34 Nm
- Latch Bolts12 lb-ft16 Nm
- Panel Bolts12 lb-ft16 Nm
- Striker Bolts31 lb-ft42 Nm
- Trim ClipsReplace if broken2 lb-ft3 Nm
Bumper Reinforcement - Rear7 specs
- Body Panel Bolts18 lb-ft25 Nm
- Bumper Cover Bolts7 lb-ft10 Nm
- Hinge Bolts25 lb-ft34 Nm
- Latch Bolts12 lb-ft16 Nm
- Panel Bolts12 lb-ft16 Nm
- Striker Bolts31 lb-ft42 Nm
- Trim ClipsReplace if broken2 lb-ft3 Nm
Door Check/Stop6 specs
- Body Panel Bolts18 lb-ft25 Nm
- Hinge Bolts25 lb-ft34 Nm
- Latch Bolts12 lb-ft16 Nm
- Panel Bolts12 lb-ft16 Nm
- Striker Bolts31 lb-ft42 Nm
- Trim ClipsReplace if broken2 lb-ft3 Nm
Door Glass5 specs
- Hinge Bolts25 lb-ft34 Nm
- Latch Bolts12 lb-ft16 Nm
- Panel Bolts12 lb-ft16 Nm
- Striker Bolts31 lb-ft42 Nm
- Trim ClipsReplace if broken2 lb-ft3 Nm
Door Handle - Exterior7 specs
- Handle Mounting Bolts6 lb-ft8 Nm
- Hinge Bolts25 lb-ft34 Nm
- Latch Bolts12 lb-ft16 Nm
- Lock Rod Clips4 lb-ft5 Nm
- Panel Bolts12 lb-ft16 Nm
- Striker Bolts31 lb-ft42 Nm
- Trim ClipsReplace if broken2 lb-ft3 Nm
Door Handle - Interior7 specs
- Cable Clips4 lb-ft5 Nm
- Handle Screws2 lb-ft3 Nm
- Hinge Bolts25 lb-ft34 Nm
- Latch Bolts12 lb-ft16 Nm
- Panel Bolts12 lb-ft16 Nm
- Striker Bolts31 lb-ft42 Nm
- Trim ClipsReplace if broken2 lb-ft3 Nm
Door Hinge6 specs
- Door Hinge Bolts22 lb-ft30 Nm
- Hinge Bolts25 lb-ft34 Nm
- Latch Bolts12 lb-ft16 Nm
- Panel Bolts12 lb-ft16 Nm
- Striker Bolts31 lb-ft42 Nm
- Trim ClipsReplace if broken2 lb-ft3 Nm
Door Shell7 specs
- Body Panel Bolts18 lb-ft25 Nm
- Door Hinge Bolts22 lb-ft30 Nm
- Hinge Bolts25 lb-ft34 Nm
- Latch Bolts12 lb-ft16 Nm
- Panel Bolts12 lb-ft16 Nm
- Striker Bolts31 lb-ft42 Nm
- Trim ClipsReplace if broken2 lb-ft3 Nm
Door Skin7 specs
- Body Panel Bolts18 lb-ft25 Nm
- Door Hinge Bolts22 lb-ft30 Nm
- Hinge Bolts25 lb-ft34 Nm
- Latch Bolts12 lb-ft16 Nm
- Panel Bolts12 lb-ft16 Nm
- Striker Bolts31 lb-ft42 Nm
- Trim ClipsReplace if broken2 lb-ft3 Nm
Door Weatherstrip5 specs
- Hinge Bolts25 lb-ft34 Nm
- Latch Bolts12 lb-ft16 Nm
- Panel Bolts12 lb-ft16 Nm
- Striker Bolts31 lb-ft42 Nm
- Trim ClipsReplace if broken2 lb-ft3 Nm
Fender8 specs
- Fender Bolts9 lb-ft12 Nm
- Fender Liner Screws2 lb-ft3 Nm
- Hinge Bolts25 lb-ft34 Nm
- Hood Hinge Bolts18 lb-ft25 Nm
- Latch Bolts12 lb-ft16 Nm
- Panel Bolts12 lb-ft16 Nm
- Striker Bolts31 lb-ft42 Nm
- Trim ClipsReplace if broken2 lb-ft3 Nm
Fender Liner7 specs
- Body Panel Bolts18 lb-ft25 Nm
- Bumper Cover Bolts7 lb-ft10 Nm
- Hinge Bolts25 lb-ft34 Nm
- Latch Bolts12 lb-ft16 Nm
- Panel Bolts12 lb-ft16 Nm
- Striker Bolts31 lb-ft42 Nm
- Trim ClipsReplace if broken2 lb-ft3 Nm
Grille7 specs
- Clips4 lb-ft5 Nm
- Grille Mounting Screws2 lb-ft3 Nm
- Hinge Bolts25 lb-ft34 Nm
- Latch Bolts12 lb-ft16 Nm
- Panel Bolts12 lb-ft16 Nm
- Striker Bolts31 lb-ft42 Nm
- Trim ClipsReplace if broken2 lb-ft3 Nm
Hood8 specs
- Hinge Bolts25 lb-ft34 Nm
- Hood Hinge Bolts18 lb-ft25 Nm
- Hood Latch Bolts9 lb-ft12 Nm
- Hood Strut Bolts7 lb-ft10 Nm
- Latch Bolts12 lb-ft16 Nm
- Panel Bolts12 lb-ft16 Nm
- Striker Bolts31 lb-ft42 Nm
- Trim ClipsReplace if broken2 lb-ft3 Nm
Hood Hinge6 specs
- Body Panel Bolts18 lb-ft25 Nm
- Hinge Bolts25 lb-ft34 Nm
- Latch Bolts12 lb-ft16 Nm
- Panel Bolts12 lb-ft16 Nm
- Striker Bolts31 lb-ft42 Nm
- Trim ClipsReplace if broken2 lb-ft3 Nm
Hood Latch7 specs
- Cable Clips4 lb-ft5 Nm
- Hinge Bolts25 lb-ft34 Nm
- Hood Latch Bolts9 lb-ft12 Nm
- Latch Bolts12 lb-ft16 Nm
- Panel Bolts12 lb-ft16 Nm
- Striker Bolts31 lb-ft42 Nm
- Trim ClipsReplace if broken2 lb-ft3 Nm
Hood Release Cable7 specs
- Body Panel Bolts18 lb-ft25 Nm
- Bumper Cover Bolts7 lb-ft10 Nm
- Hinge Bolts25 lb-ft34 Nm
- Latch Bolts12 lb-ft16 Nm
- Panel Bolts12 lb-ft16 Nm
- Striker Bolts31 lb-ft42 Nm
- Trim ClipsReplace if broken2 lb-ft3 Nm
Hood Strut6 specs
- Body Panel Bolts18 lb-ft25 Nm
- Hinge Bolts25 lb-ft34 Nm
- Latch Bolts12 lb-ft16 Nm
- Panel Bolts12 lb-ft16 Nm
- Striker Bolts31 lb-ft42 Nm
- Trim ClipsReplace if broken2 lb-ft3 Nm
Quarter Glass6 specs
- Body Panel Bolts18 lb-ft25 Nm
- Hinge Bolts25 lb-ft34 Nm
- Latch Bolts12 lb-ft16 Nm
- Panel Bolts12 lb-ft16 Nm
- Striker Bolts31 lb-ft42 Nm
- Trim ClipsReplace if broken2 lb-ft3 Nm
Quarter Panel8 specs
- Body Panel Bolts18 lb-ft25 Nm
- Bumper Cover Bolts7 lb-ft10 Nm
- Door Hinge Bolts22 lb-ft30 Nm
- Hinge Bolts25 lb-ft34 Nm
- Latch Bolts12 lb-ft16 Nm
- Panel Bolts12 lb-ft16 Nm
- Striker Bolts31 lb-ft42 Nm
- Trim ClipsReplace if broken2 lb-ft3 Nm
Rear Window6 specs
- Body Panel Bolts18 lb-ft25 Nm
- Hinge Bolts25 lb-ft34 Nm
- Latch Bolts12 lb-ft16 Nm
- Panel Bolts12 lb-ft16 Nm
- Striker Bolts31 lb-ft42 Nm
- Trim ClipsReplace if broken2 lb-ft3 Nm
Rocker Panel8 specs
- Body Panel Bolts18 lb-ft25 Nm
- Bumper Cover Bolts7 lb-ft10 Nm
- Door Hinge Bolts22 lb-ft30 Nm
- Hinge Bolts25 lb-ft34 Nm
- Latch Bolts12 lb-ft16 Nm
- Panel Bolts12 lb-ft16 Nm
- Striker Bolts31 lb-ft42 Nm
- Trim ClipsReplace if broken2 lb-ft3 Nm
Side Mirror Glass5 specs
- Hinge Bolts25 lb-ft34 Nm
- Latch Bolts12 lb-ft16 Nm
- Panel Bolts12 lb-ft16 Nm
- Striker Bolts31 lb-ft42 Nm
- Trim ClipsReplace if broken2 lb-ft3 Nm
Trunk Hinge7 specs
- Body Panel Bolts18 lb-ft25 Nm
- Door Hinge Bolts22 lb-ft30 Nm
- Hinge Bolts25 lb-ft34 Nm
- Latch Bolts12 lb-ft16 Nm
- Panel Bolts12 lb-ft16 Nm
- Striker Bolts31 lb-ft42 Nm
- Trim ClipsReplace if broken2 lb-ft3 Nm
Trunk Latch6 specs
- Body Panel Bolts18 lb-ft25 Nm
- Hinge Bolts25 lb-ft34 Nm
- Latch Bolts12 lb-ft16 Nm
- Panel Bolts12 lb-ft16 Nm
- Striker Bolts31 lb-ft42 Nm
- Trim ClipsReplace if broken2 lb-ft3 Nm
Trunk Lid7 specs
- Hinge Bolts25 lb-ft34 Nm
- Latch Bolts12 lb-ft16 Nm
- Panel Bolts12 lb-ft16 Nm
- Striker Bolts31 lb-ft42 Nm
- Trim ClipsReplace if broken2 lb-ft3 Nm
- Trunk Hinge Bolts18 lb-ft25 Nm
- Trunk Latch Bolts9 lb-ft12 Nm
Trunk Strut6 specs
- Body Panel Bolts18 lb-ft25 Nm
- Hinge Bolts25 lb-ft34 Nm
- Latch Bolts12 lb-ft16 Nm
- Panel Bolts12 lb-ft16 Nm
- Striker Bolts31 lb-ft42 Nm
- Trim ClipsReplace if broken2 lb-ft3 Nm
Windshield6 specs
- Body Panel Bolts18 lb-ft25 Nm
- Hinge Bolts25 lb-ft34 Nm
- Latch Bolts12 lb-ft16 Nm
- Panel Bolts12 lb-ft16 Nm
- Striker Bolts31 lb-ft42 Nm
- Trim ClipsReplace if broken2 lb-ft3 Nm
Windshield Molding5 specs
- Hinge Bolts25 lb-ft34 Nm
- Latch Bolts12 lb-ft16 Nm
- Panel Bolts12 lb-ft16 Nm
- Striker Bolts31 lb-ft42 Nm
- Trim ClipsReplace if broken2 lb-ft3 Nm
Interior
Armrest2 specs
- Connector Bolts6 lb-ft8 Nm
- Trim Panel ClipsReplace if damaged1.5 lb-ft2 Nm
Carpet4 specs
- Connector Bolts6 lb-ft8 Nm
- Dashboard Screws2 lb-ft3 Nm
- Seat Mounting BoltsSafety critical33 lb-ft45 Nm
- Trim Panel ClipsReplace if damaged1.5 lb-ft2 Nm
Center Console3 specs
- Connector Bolts6 lb-ft8 Nm
- Console Screws2 lb-ft3 Nm
- Shifter Trim4 lb-ft5 Nm
Dash Pad4 specs
- Connector Bolts6 lb-ft8 Nm
- Dashboard Screws2 lb-ft3 Nm
- Seat Mounting BoltsSafety critical33 lb-ft45 Nm
- Trim Panel ClipsReplace if damaged1.5 lb-ft2 Nm
Dashboard4 specs
- Connector Bolts6 lb-ft8 Nm
- Dashboard Bolt9 lb-ft12 Nm
- Dashboard Screws2 lb-ft3 Nm
- Trim Panel ClipsReplace if damaged1.5 lb-ft2 Nm
Door Panel3 specs
- Connector Bolts6 lb-ft8 Nm
- Door Panel Screws1.5 lb-ft2 Nm
- Trim Panel ClipsReplace if damaged1.5 lb-ft2 Nm
Floor Mat Hooks2 specs
- Connector Bolts6 lb-ft8 Nm
- Trim Panel ClipsReplace if damaged1.5 lb-ft2 Nm
Glove Box3 specs
- Connector Bolts6 lb-ft8 Nm
- Glove Box Screws2 lb-ft3 Nm
- Hinge Screws1.5 lb-ft2 Nm
Glove Box Latch3 specs
- Connector Bolts6 lb-ft8 Nm
- Dashboard Screws2 lb-ft3 Nm
- Trim Panel ClipsReplace if damaged1.5 lb-ft2 Nm
Headliner3 specs
- Connector Bolts6 lb-ft8 Nm
- Seat Mounting BoltsSafety critical33 lb-ft45 Nm
- Trim Panel ClipsReplace if damaged1.5 lb-ft2 Nm
Pedal Pads2 specs
- Connector Bolts6 lb-ft8 Nm
- Trim Panel ClipsReplace if damaged1.5 lb-ft2 Nm
Rearview Mirror2 specs
- Connector Bolts6 lb-ft8 Nm
- Trim Panel ClipsReplace if damaged1.5 lb-ft2 Nm
Seat - Front4 specs
- Connector Bolts6 lb-ft8 Nm
- Electrical Connectors4 lb-ft5 Nm
- Seat Mounting BoltsSafety critical33 lb-ft45 Nm
- Seat Track Bolts33 lb-ft45 Nm
Seat - Rear3 specs
- Connector Bolts6 lb-ft8 Nm
- Seat Back Release11 lb-ft15 Nm
- Seat Mounting Bolts26 lb-ft35 Nm
Seat Belt3 specs
- Connector Bolts6 lb-ft8 Nm
- Seat Mounting BoltsSafety critical33 lb-ft45 Nm
- Trim Panel ClipsReplace if damaged1.5 lb-ft2 Nm
Seat Belt Buckle3 specs
- Connector Bolts6 lb-ft8 Nm
- Seat Mounting BoltsSafety critical33 lb-ft45 Nm
- Trim Panel ClipsReplace if damaged1.5 lb-ft2 Nm
Seat Belt Pretensioner3 specs
- Connector Bolts6 lb-ft8 Nm
- Seat Mounting BoltsSafety critical33 lb-ft45 Nm
- Trim Panel ClipsReplace if damaged1.5 lb-ft2 Nm
Seat Cover3 specs
- Connector Bolts6 lb-ft8 Nm
- Seat Mounting BoltsSafety critical33 lb-ft45 Nm
- Trim Panel ClipsReplace if damaged1.5 lb-ft2 Nm
Seat Foam3 specs
- Connector Bolts6 lb-ft8 Nm
- Seat Mounting BoltsSafety critical33 lb-ft45 Nm
- Trim Panel ClipsReplace if damaged1.5 lb-ft2 Nm
Seat Track3 specs
- Connector Bolts6 lb-ft8 Nm
- Seat Mounting BoltsSafety critical33 lb-ft45 Nm
- Trim Panel ClipsReplace if damaged1.5 lb-ft2 Nm
Shifter Boot2 specs
- Connector Bolts6 lb-ft8 Nm
- Trim Panel ClipsReplace if damaged1.5 lb-ft2 Nm
Shifter Knob2 specs
- Connector Bolts6 lb-ft8 Nm
- Trim Panel ClipsReplace if damaged1.5 lb-ft2 Nm
Steering Wheel Cover2 specs
- Connector Bolts6 lb-ft8 Nm
- Trim Panel ClipsReplace if damaged. Verify sequence with the service manual1.5 lb-ft2 Nm
Sun Visor2 specs
- Connector Bolts6 lb-ft8 Nm
- Visor Mounting Screws2 lb-ft3 Nm
Torque is shown in lb-ft with Nm below it. Where a step says to turn, tighten the listed angle after the torque step before it. Use new bolts where the note says so.
Need labor times, fluids or repair steps for this car? See it on the Open Labor Project