Building an app? Need this data? Need this data? API access here

2019 Ford F-150 torque specs

3.5L V6 EcoBoost HO

Change vehicle

Most looked up

Maintenance

  • Tire Rotation2 specs
    • Lug Nuts - Alloy WheelsTorque in star pattern, recheck after 50 miles150 lb-ft204 Nm
    • Lug Nuts - Steel WheelsTorque in star pattern150 lb-ft204 Nm

Brakes

  • Brake Caliper - Front3 specs
    • Bleeder ScrewDo not overtighten7 lb-ft10 Nm
    • Brake Line Banjo BoltUse new copper washers30 lb-ft40 Nm
    • Caliper Bracket BoltsThreadlocker recommended88 lb-ft120 Nm
  • Brake Caliper - Rear3 specs
    • Bleeder ScrewDo not overtighten7 lb-ft10 Nm
    • Brake Line Banjo BoltUse new copper washers30 lb-ft40 Nm
    • Caliper Bracket BoltsThreadlocker recommended80 lb-ft109 Nm
  • Brake Master Cylinder2 specs
    • Brake Line FittingsUse flare nut wrench11 lb-ft15 Nm
    • Master Cylinder Nuts18 lb-ft25 Nm
  • Brake Master Cylinder Rebuild3 specs
    • Brake Line FittingsUse flare nut wrench11 lb-ft15 Nm
    • Master Cylinder Mounting Nuts18 lb-ft25 Nm
    • Reservoir Mounting Bolts6 lb-ft8 Nm
  • Brake Pads - Front3 specs
    • Caliper Bracket BoltsThreadlocker recommended88 lb-ft120 Nm
    • Caliper Slide Pin BoltsApply silicone brake grease26 lb-ft35 Nm
    • Wheel Lug NutsTorque in star pattern103 lb-ft140 Nm
  • Brake Pads - Rear3 specs
    • Caliper Bracket BoltsThreadlocker recommended80 lb-ft109 Nm
    • Caliper Slide Pin BoltsApply silicone brake grease22 lb-ft30 Nm
    • Wheel Lug NutsTorque in star pattern103 lb-ft140 Nm
  • Front Brake Pad Replacement3 specs
    • Caliper Bracket BoltsThreadlocker recommended88 lb-ft120 Nm
    • Caliper Slide Pin BoltsApply silicone brake grease26 lb-ft35 Nm
    • Wheel Lug NutsTorque in star pattern103 lb-ft140 Nm
  • Rear Brake Shoe Replacement3 specs
    • Backing Plate Bolts44 lb-ft60 Nm
    • Wheel Cylinder Bolts9 lb-ft12 Nm
    • Wheel Lug NutsTorque in star pattern103 lb-ft140 Nm

Engine

  • Engine Mount - Front3 specs
    • Engine Mount-to-Block Bolts46 lb-ft63 Nm
    • Engine Mount-to-Frame Bolts79 lb-ft107 Nm
    • Through-Bolt63 lb-ft85 Nm
  • Exhaust Manifold Gasket3 specs
    • Exhaust Manifold NutsApply anti-seize, work hot-to-cold18 lb-ft24 Nm
    • Exhaust Manifold StudsIf replacing studs11 lb-ft15 Nm
    • Heat Shield Bolts7 lb-ft10 Nm
  • Fan Belt Replacement3 specs
    • Idler Pulley Bolt30 lb-ft40 Nm
    • Tensioner Mounting Bolts18 lb-ft25 Nm
    • Tensioner Pulley Bolt33 lb-ft45 Nm
  • Flywheel2 specs
    • Flexplate BoltsAutomatic transmissions63 lb-ft85 Nm
    • Flywheel BoltsOften TTY - check specs, tighten in star pattern70 lb-ft95 Nm
  • Full Engine Tune-Up5 specs
    • Ignition Coil Bolts6 lb-ft8 Nm
    • Spark Plugs - Aluminum HeadApply anti-seize to threads15 lb-ft20 Nm
    • Spark Plugs - Cast Iron HeadApply anti-seize to threads22 lb-ft30 Nm
    • Throttle Body Bolts7 lb-ft10 Nm
    • Valve Cover BoltsTighten in sequence7 lb-ft10 Nm
  • Head Gasket - Single6 specs
    • Exhaust Manifold NutsApply anti-seize18 lb-ft25 Nm
    • Intake Manifold BoltsTighten in sequence18 lb-ft25 Nm
    • Cylinder Head Bolts - Step 1Always use new TTY bolts30 lb-ft40 Nm
    • Cylinder Head Bolts - Step 2Tighten in sequence33 lb-ft45 Nm
    • Cylinder Head Bolts - Step 3Plus 90 degreesTurn 90°
    • Cylinder Head Bolts - Step 4Plus 90 degreesTurn 90°
  • Intake Manifold Gasket3 specs
    • Fuel Rail Bolts9 lb-ft12 Nm
    • Intake Manifold BoltsTighten in sequence from center out7 lb-ft10 Nm
    • Throttle Body Bolts7 lb-ft10 Nm
  • Oil Change3 specs
    • Oil Drain PlugUse new crush washer21 lb-ft28 Nm
    • Oil Filter (Spin-On)Hand tight plus 3/4 turn15 lb-ft20 Nm
    • Oil Filter Housing CapFor cartridge-type filters18 lb-ft25 Nm
  • Oil Pan Gasket2 specs
    • Oil Drain PlugUse new crush washer21 lb-ft28 Nm
    • Oil Pan BoltsTighten in sequence from center outward18 lb-ft25 Nm
  • Serpentine Belt2 specs
    • Belt Tensioner Bolt41 lb-ft55 Nm
    • Idler Pulley Bolt33 lb-ft45 Nm
  • Throttle Body2 specs
    • Air Intake Hose Clamps2 lb-ft3 Nm
    • Throttle Body Bolts7 lb-ft10 Nm
  • Timing Chain5 specs
    • Camshaft Sprocket Bolts32 lb-ft44 Nm
    • Crankshaft Sprocket BoltOften TTY - check specs133 lb-ft + 90°180 Nm
    • Timing Chain Guide Bolts9 lb-ft12 Nm
    • Timing Chain Tensioner8 lb-ft11 Nm
    • Timing Cover BoltsTighten in sequence9 lb-ft12 Nm
  • Timing Chain Tensioner3 specs
    • Tensioner Cap/PlugUse new crush washer if equipped22 lb-ft30 Nm
    • Tensioner Housing BoltsTighten in sequence18 lb-ft25 Nm
    • Timing Cover Access Bolts9 lb-ft12 Nm
  • Transmission Mount2 specs
    • Crossmember Bolts70 lb-ft95 Nm
    • Transmission Mount Bolts69 lb-ft94 Nm
  • Valve Cover Gasket - Single2 specs
    • Spark Plug Tube SealsIf equipped with separate seals9 lb-ft12 Nm
    • Valve Cover BoltsTighten in sequence7 lb-ft10 Nm

Cooling

  • Coolant Outlet3 specs
    • Coolant Outlet/Housing BoltsTighten in sequence9 lb-ft12 Nm
    • Coolant Temperature Sensor15 lb-ft20 Nm
    • Hose ClampsSpring or constant-tension preferred2 lb-ft3 Nm
  • Radiator4 specs
    • Drain PetcockPlastic - hand tight4 lb-ft5 Nm
    • Radiator Mount BoltsDo not overtighten plastic mounts9 lb-ft12 Nm
    • Transmission Cooler LinesIf equipped18 lb-ft25 Nm
    • Upper/Lower Hose Clamps2 lb-ft3 Nm
  • Radiator Removal and Service4 specs
    • Drain PetcockPlastic - hand-tight only4 lb-ft5 Nm
    • Fan Shroud Bolts7 lb-ft10 Nm
    • Radiator Mount BoltsDo not overtighten plastic mounts9 lb-ft12 Nm
    • Transmission Cooler LinesIf equipped, use new washers18 lb-ft25 Nm
  • Thermostat2 specs
    • Coolant Temperature SensorUse thread sealant15 lb-ft20 Nm
    • Thermostat Housing Bolts11 lb-ft15 Nm
  • Water Pump3 specs
    • Hose ClampsSpring clamps preferred2 lb-ft3 Nm
    • Thermostat Housing Bolts11 lb-ft15 Nm
    • Water Pump BoltsTighten in criss-cross pattern14 lb-ft19 Nm

Ignition

  • Spark Plugs3 specs
    • Ignition Coil Bolts6 lb-ft8 Nm
    • Spark Plugs - Aluminum HeadApply anti-seize to threads15 lb-ft20 Nm
    • Spark Plugs - Cast Iron HeadApply anti-seize to threads22 lb-ft30 Nm

Fuel system

  • Fuel Filter2 specs
    • Fuel Filter Bracket Bolt7 lb-ft10 Nm
    • Fuel Line FittingsIf threaded type18 lb-ft25 Nm
  • Fuel Pump2 specs
    • Fuel Pump Module Lock RingUse special tool59 lb-ft80 Nm
    • Tank Strap Bolts26 lb-ft35 Nm

Electrical

  • Alternator4 specs
    • Alternator Mounting Bolts18 lb-ft25 Nm
    • Alternator Pivot Bolt18 lb-ft25 Nm
    • Battery Terminal BoltsDo not overtighten6 lb-ft8 Nm
    • Serpentine Belt Tensioner41 lb-ft55 Nm
  • Battery3 specs
    • Battery Hold-Down Bolt6 lb-ft8 Nm
    • Battery Terminal BoltsDo not overtighten - can crack terminal4 lb-ft6 Nm
    • Battery Tray Bolts9 lb-ft12 Nm
  • Blower Motor2 specs
    • Blower Motor Resistor Screws1.5 lb-ft2 Nm
    • Blower Motor Screws3 lb-ft4 Nm
  • Starter3 specs
    • Heat Shield BoltsIf equipped7 lb-ft10 Nm
    • Starter Mounting BoltsLong bolt may need extension18 lb-ft25 Nm
    • Starter Solenoid NutFor B+ cable9 lb-ft12 Nm

Suspension

  • Front Suspension Rebuild5 specs
    • Ball Joint Pinch BoltUse new bolt if locknut style37 lb-ft50 Nm
    • Lower Control Arm BoltsTorque at ride height212 lb-ft288 Nm
    • Strut Top Mount Nuts18 lb-ft25 Nm
    • Sway Bar End Link Nuts44 lb-ft60 Nm
    • Upper Control Arm BoltsTorque at ride height96 lb-ft130 Nm
  • Rear Suspension Service4 specs
    • Lower Control Arm BoltsTorque at ride height66 lb-ft90 Nm
    • Shock Lower Bolt80 lb-ft108 Nm
    • Sway Bar End Link Nuts37 lb-ft50 Nm
    • Trailing Arm BoltsTorque at ride height88 lb-ft120 Nm
  • Strut Assembly - Front4 specs
    • Strut Mount Center NutHold strut shaft with Allen key46 lb-ft63 Nm
    • Strut Tower NutsDo not loosen center nut unless compressed34 lb-ft46 Nm
    • Strut-to-Knuckle BoltsOften TTY111 lb-ft150 Nm
    • Sway Bar End Link Nuts41 lb-ft55 Nm

Steering

  • Power Steering Pump4 specs
    • Power Steering Pump Bolts18 lb-ft25 Nm
    • Pressure Line FittingUse new O-rings22 lb-ft30 Nm
    • Return Line Clamp3 lb-ft4 Nm
    • Serpentine Belt Tensioner41 lb-ft55 Nm

Drivetrain

  • Driveshaft - Front3 specs
    • Center Support Bearing Bracket Bolts37 lb-ft50 Nm
    • Driveshaft Flange Bolts (CV/U-Joint)Use new bolts if torque-to-yield55 lb-ft75 Nm
    • Transfer Case Output Yoke NutIf accessible133 lb-ft180 Nm
  • Driveshaft - Rear3 specs
    • Differential Pinion Yoke NutUse new nut, set pinion preload184 lb-ft250 Nm
    • Driveshaft Flange Bolts55 lb-ft75 Nm
    • U-Joint Strap BoltsApply threadlocker26 lb-ft35 Nm
  • Driveshaft Center Support Bearing2 specs
    • Center Support Bearing Bracket Bolts35 lb-ft47 Nm
    • Driveshaft Flange Bolts55 lb-ft75 Nm
  • Transfer Case Fluid Change2 specs
    • Transfer Case Drain Plug18 lb-ft25 Nm
    • Transfer Case Fill Plug18 lb-ft25 Nm
  • Wheel Bearing Hub - Front4 specs
    • ABS Sensor BoltDo not overtighten7 lb-ft10 Nm
    • Axle NutUse new cotter pin after torque187 lb-ft254 Nm
    • Brake Caliper Bracket Bolts88 lb-ft120 Nm
    • Wheel Bearing Hub BoltsApply threadlocker if specified81 lb-ft110 Nm
  • Wheel Bearing Hub - Rear3 specs
    • Axle NutUse new cotter pin after torque148 lb-ft200 Nm
    • Brake Caliper Bracket Bolts81 lb-ft110 Nm
    • Wheel Bearing Hub BoltsApply threadlocker if specified74 lb-ft100 Nm

Exhaust

  • Muffler2 specs
    • Hanger Bracket Bolts18 lb-ft25 Nm
    • Muffler Clamps41 lb-ft55 Nm

Heating and A/C

  • AC Compressor3 specs
    • AC Compressor Mounting Bolts18 lb-ft25 Nm
    • AC Line FittingsUse new O-rings, add PAG oil16 lb-ft22 Nm
    • Clutch Connector Bolt6 lb-ft8 Nm
  • AC Condenser2 specs
    • AC Line FittingsUse new O-rings15 lb-ft20 Nm
    • Condenser Mounting Bolts9 lb-ft12 Nm

Torque is shown in lb-ft with Nm below it. Where a step says to turn, tighten the listed angle after the torque step before it. Use new bolts where the note says so.

Need labor times, fluids or repair steps for this car? See it on the Open Labor Project