RQUE SPECS2009 Chevrolet Silverado 2500HD torque specs
6.0L V8 Vortec
Change vehicle
Most looked up
- Lug nuts140 lb-ft190 Nm
- Oil drain plug18 lb-ft25 Nm
- Spark plugs15 lb-ft20 Nm
- Front caliper bracket bolts163 lb-ft221 Nm
- Rear caliper bracket bolts109 lb-ft148 Nm
- Front axle nut159 lb-ft216 Nm
- Outer tie rod end nut54 lb-ft73 Nm
Maintenance
AC System Diagnosis2 specs
- AC Line FittingsNew O-rings20 lb-ft27 Nm
- Connector Bolts7 lb-ft9 Nm
Air Filter4 specs
- Air Box Clips4 lb-ft5 Nm
- Intake Tube Clamp4 lb-ft5 Nm
- MAF Sensor Screws4 lb-ft5 Nm
- Mass Air Flow Sensor Screws3 lb-ft4 Nm
Battery Test4 specs
- Battery Hold-Down BoltDo not overtighten11 lb-ft15 Nm
- Battery Terminal BoltsClean terminals7 lb-ft9 Nm
- Connector Bolts7 lb-ft9 Nm
- Ground Cable Bolt14 lb-ft18 Nm
Charging System Test1 spec
- Connector Bolts7 lb-ft9 Nm
Check Engine Light Diagnosis1 spec
- Connector Bolts7 lb-ft9 Nm
Compression Test2 specs
- Air Box Clips4 lb-ft5 Nm
- Connector Bolts7 lb-ft9 Nm
Cooling System Pressure Test1 spec
- Connector Bolts7 lb-ft9 Nm
Diagnostic Scan1 spec
- Connector Bolts7 lb-ft9 Nm
Differential Service4 specs
- Connector Bolts7 lb-ft9 Nm
- Drain PlugNew washer41 lb-ft55 Nm
- Fill Plug41 lb-ft55 Nm
- Oil Drain PlugUse new crush washer26 lb-ft35 Nm
Drivability Diagnosis2 specs
- Air Box Clips4 lb-ft5 Nm
- Connector Bolts7 lb-ft9 Nm
Electrical Diagnosis1 spec
- Connector Bolts7 lb-ft9 Nm
Fluid Leak Diagnosis1 spec
- Connector Bolts7 lb-ft9 Nm
Leak-Down Test2 specs
- Air Box Clips4 lb-ft5 Nm
- Connector Bolts7 lb-ft9 Nm
Noise Diagnosis2 specs
- Connector Bolts7 lb-ft9 Nm
- Wheel Lug NutsTorque in star pattern140 lb-ft190 Nm
Power Steering Service4 specs
- Air Box ClipsVerify sequence with the service manual4 lb-ft5 Nm
- Connector Bolts7 lb-ft9 Nm
- Pressure Line FittingNew O-ring34 lb-ft46 Nm
- Pump Mounting Bolts27 lb-ft37 Nm
Tire Balance2 specs
- Connector Bolts7 lb-ft9 Nm
- Wheel Lug NutsTorque in star pattern140 lb-ft190 Nm
Tire Mount and Balance2 specs
- Connector Bolts7 lb-ft9 Nm
- Wheel Lug NutsTorque in star pattern140 lb-ft190 Nm
Tire Rotation2 specs
- Lug Nuts - Alloy WheelsTorque in star pattern, recheck after 50 miles140 lb-ft190 Nm
- Lug Nuts - Steel WheelsTorque in star pattern140 lb-ft190 Nm
TPMS Relearn1 spec
- Connector Bolts7 lb-ft9 Nm
TPMS Sensor2 specs
- Connector Bolts7 lb-ft9 Nm
- Wheel Lug NutsTorque in star pattern140 lb-ft190 Nm
Transmission Service1 spec
- Connector Bolts7 lb-ft9 Nm
Tune-Up - Major3 specs
- Air Box Clips4 lb-ft5 Nm
- Connector Bolts7 lb-ft9 Nm
- Oil Drain PlugUse new crush washer26 lb-ft35 Nm
Tune-Up - Minor3 specs
- Air Box Clips4 lb-ft5 Nm
- Connector Bolts7 lb-ft9 Nm
- Oil Drain PlugUse new crush washer26 lb-ft35 Nm
Wheel Alignment9 specs
- Air Box Clips4 lb-ft5 Nm
- Cam BoltsAfter adjustment124 lb-ft168 Nm
- Camber BoltsIf adjustable55 lb-ft75 Nm
- Connector Bolts7 lb-ft9 Nm
- Oil Drain PlugUse new crush washer26 lb-ft35 Nm
- Subframe BoltsIf adjusted115 lb-ft156 Nm
- Tie Rod Jam Nuts41 lb-ft55 Nm
- Tie Rod Lock NutAfter adjustment65 lb-ft88 Nm
- Wheel Lug NutsTorque in star pattern140 lb-ft190 Nm
Brakes
ABS Module5 specs
- ABS Module Bolts7 lb-ft10 Nm
- Bleeder Screw14 lb-ft18 Nm
- Brake Line FittingsUse flare nut wrench11 lb-ft15 Nm
- Caliper Mounting Bolts88 lb-ft119 Nm
- Wheel Lug NutsTorque in star pattern147 lb-ft200 Nm
ABS Pump3 specs
- Bleeder ScrewDo not overtighten7 lb-ft10 Nm
- Caliper Mounting Bolts88 lb-ft119 Nm
- Wheel Lug NutsTorque in star pattern140 lb-ft190 Nm
ABS Tone Ring4 specs
- Caliper Bracket Bolts - FrontThreadlocker recommended88 lb-ft120 Nm
- Caliper Mounting Bolts88 lb-ft119 Nm
- Caliper Slide Pin BoltsApply silicone brake grease26 lb-ft35 Nm
- Wheel Lug NutsTorque in star pattern140 lb-ft190 Nm
ABS Wheel Speed Sensor - Front5 specs
- ABS Sensor BoltDo not overtighten7 lb-ft10 Nm
- Bleeder Screw14 lb-ft18 Nm
- Caliper Mounting BoltsUse thread locker88 lb-ft119 Nm
- Wheel Bearing Hub Bolts81 lb-ft110 Nm
- Wheel Lug NutsTorque in star pattern135 lb-ft183 Nm
ABS Wheel Speed Sensor - Rear4 specs
- ABS Sensor BoltDo not overtighten7 lb-ft10 Nm
- Bleeder Screw14 lb-ft18 Nm
- Caliper Mounting BoltsUse thread locker88 lb-ft119 Nm
- Wheel Lug Nuts135 lb-ft183 Nm
Brake Bleed - All Four3 specs
- Bleeder ScrewDo not overtighten. Verify sequence with the service manual7 lb-ft10 Nm
- Caliper Mounting BoltsUse thread locker88 lb-ft119 Nm
- Wheel Lug NutsTorque in star pattern. Verify sequence with the service manual140 lb-ft190 Nm
Brake Booster6 specs
- Bleeder Screw14 lb-ft18 Nm
- Brake Booster NutsVerify sequence with the service manual18 lb-ft25 Nm
- Brake Pedal Pushrod LockVerify sequence with the service manual11 lb-ft15 Nm
- Caliper Mounting BoltsUse thread locker88 lb-ft119 Nm
- Master Cylinder NutsVerify sequence with the service manual18 lb-ft25 Nm
- Wheel Lug Nuts140 lb-ft190 Nm
Brake Booster Check Valve1 spec
- Caliper Mounting Bolts88 lb-ft119 Nm
Brake Caliper - Front3 specs
- Bleeder ScrewDo not overtighten7 lb-ft10 Nm
- Brake Line Banjo BoltUse new copper washers18 lb-ft25 Nm
- Caliper Bracket BoltsThreadlocker recommended88 lb-ft120 Nm
Brake Caliper - Rear3 specs
- Bleeder ScrewDo not overtighten7 lb-ft10 Nm
- Brake Line Banjo BoltUse new copper washers18 lb-ft25 Nm
- Caliper Bracket BoltsThreadlocker recommended74 lb-ft100 Nm
Brake Caliper Bracket6 specs
- Bleeder ScrewDo not overtighten. Verify sequence with the service manual7 lb-ft10 Nm
- Brake Hose Banjo BoltNew copper washers41 lb-ft55 Nm
- Caliper Bracket Bolts - FrontThreadlocker recommended. Verify sequence with the service manual88 lb-ft120 Nm
- Caliper Mounting BoltsUse thread locker88 lb-ft119 Nm
- Caliper Slide Pin BoltsApply silicone brake grease. Verify sequence with the service manual26 lb-ft35 Nm
- Wheel Lug NutsTorque in star pattern. Verify sequence with the service manual140 lb-ft190 Nm
Brake Caliper Rebuild - Front5 specs
- Bleeder ScrewDo not overtighten7 lb-ft10 Nm
- Caliper Bracket Bolts - FrontThreadlocker recommended163 lb-ft221 Nm
- Caliper Mounting Bolts88 lb-ft119 Nm
- Caliper Slide Pin BoltsApply silicone brake grease26 lb-ft35 Nm
- Wheel Lug NutsTorque in star pattern140 lb-ft190 Nm
Brake Caliper Rebuild - Rear5 specs
- Bleeder ScrewDo not overtighten7 lb-ft10 Nm
- Caliper Bracket Bolts - FrontThreadlocker recommended109 lb-ft148 Nm
- Caliper Mounting BoltsUse thread locker88 lb-ft119 Nm
- Caliper Slide Pin BoltsApply silicone brake grease26 lb-ft35 Nm
- Wheel Lug NutsTorque in star pattern140 lb-ft190 Nm
Brake Caliper Slide Pins4 specs
- Caliper Bracket Bolts - FrontThreadlocker recommended88 lb-ft120 Nm
- Caliper Mounting Bolts88 lb-ft119 Nm
- Caliper Slide Pin BoltsApply silicone brake grease26 lb-ft35 Nm
- Wheel Lug NutsTorque in star pattern140 lb-ft190 Nm
Brake Drum - Rear3 specs
- Caliper Bracket Bolts - FrontThreadlocker recommended. Verify sequence with the service manual109 lb-ft148 Nm
- Caliper Mounting Bolts88 lb-ft119 Nm
- Wheel Lug NutsTorque in star pattern. Verify sequence with the service manual140 lb-ft190 Nm
Brake Fluid Flush7 specs
- Air Box ClipsVerify sequence with the service manual4 lb-ft5 Nm
- Bleeder ScrewDo not overtighten. Verify sequence with the service manual7 lb-ft10 Nm
- Caliper Mounting Bolts88 lb-ft119 Nm
- Connector Bolts7 lb-ft9 Nm
- Master Cylinder CapHand tight4 lb-ft5 Nm
- Oil Drain PlugUse new crush washer. Verify sequence with the service manual26 lb-ft35 Nm
- Wheel Lug NutsTorque in star pattern. Verify sequence with the service manual140 lb-ft190 Nm
Brake Hose - Front5 specs
- Bleeder Screw14 lb-ft18 Nm
- Brake Hose Banjo BoltUse new copper washers. Verify sequence with the service manual18 lb-ft25 Nm
- Brake Hose BracketVerify sequence with the service manual7 lb-ft10 Nm
- Caliper Mounting Bolts88 lb-ft119 Nm
- Wheel Lug Nuts140 lb-ft190 Nm
Brake Hose - Rear5 specs
- Bleeder Screw14 lb-ft18 Nm
- Brake Hose Banjo BoltUse new copper washers. Verify sequence with the service manual18 lb-ft25 Nm
- Brake Hose BracketVerify sequence with the service manual7 lb-ft10 Nm
- Caliper Mounting BoltsUse thread locker88 lb-ft119 Nm
- Wheel Lug Nuts140 lb-ft190 Nm
Brake Light Switch1 spec
- Caliper Mounting BoltsUse thread locker88 lb-ft119 Nm
Brake Line - Single3 specs
- Bleeder ScrewDo not overtighten. Verify sequence with the service manual7 lb-ft10 Nm
- Caliper Mounting Bolts88 lb-ft119 Nm
- Wheel Lug NutsTorque in star pattern. Verify sequence with the service manual140 lb-ft190 Nm
Brake Lines - Complete Set3 specs
- Bleeder ScrewDo not overtighten. Verify sequence with the service manual7 lb-ft10 Nm
- Caliper Mounting Bolts88 lb-ft119 Nm
- Wheel Lug NutsTorque in star pattern. Verify sequence with the service manual140 lb-ft190 Nm
Brake Master Cylinder2 specs
- Brake Line FittingsUse flare nut wrench11 lb-ft15 Nm
- Master Cylinder Nuts18 lb-ft25 Nm
Brake Master Cylinder Rebuild3 specs
- Brake Line FittingsUse flare nut wrench11 lb-ft15 Nm
- Master Cylinder Mounting Nuts18 lb-ft25 Nm
- Reservoir Mounting Bolts6 lb-ft8 Nm
Brake Pads - Front3 specs
- Caliper Bracket BoltsThreadlocker recommended88 lb-ft120 Nm
- Caliper Slide Pin BoltsApply silicone brake grease26 lb-ft35 Nm
- Wheel Lug NutsTorque in star pattern140 lb-ft190 Nm
Brake Pads - Rear3 specs
- Caliper Bracket BoltsThreadlocker recommended74 lb-ft100 Nm
- Caliper Slide Pin BoltsApply silicone brake grease22 lb-ft30 Nm
- Wheel Lug NutsTorque in star pattern140 lb-ft190 Nm
Brake Pads and Rotors - Front7 specs
- Bleeder ScrewDo not overtighten. Verify sequence with the service manual7 lb-ft10 Nm
- Caliper Bracket BoltsUse thread locker163 lb-ft221 Nm
- Caliper Bracket Bolts - FrontThreadlocker recommended. Verify sequence with the service manual163 lb-ft221 Nm
- Caliper Mounting BoltsUse thread locker88 lb-ft119 Nm
- Caliper Slide BoltsLubricate pins34 lb-ft46 Nm
- Caliper Slide Pin BoltsApply silicone brake grease. Verify sequence with the service manual26 lb-ft35 Nm
- Wheel Lug NutsTorque in star pattern. Verify sequence with the service manual140 lb-ft190 Nm
Brake Pads and Rotors - Rear7 specs
- Bleeder ScrewDo not overtighten. Verify sequence with the service manual7 lb-ft10 Nm
- Caliper Bracket BoltsUse thread locker109 lb-ft148 Nm
- Caliper Bracket Bolts - FrontThreadlocker recommended. Verify sequence with the service manual109 lb-ft148 Nm
- Caliper Mounting BoltsUse thread locker88 lb-ft119 Nm
- Caliper Slide BoltsLubricate pins34 lb-ft46 Nm
- Caliper Slide Pin BoltsApply silicone brake grease. Verify sequence with the service manual26 lb-ft35 Nm
- Wheel Lug NutsTorque in star pattern. Verify sequence with the service manual140 lb-ft190 Nm
Brake Proportioning Valve5 specs
- Bleeder Screw14 lb-ft18 Nm
- Brake Line FittingsUse flare nut wrench. Verify sequence with the service manual11 lb-ft15 Nm
- Caliper Mounting BoltsUse thread locker88 lb-ft119 Nm
- Proportioning Valve BoltsVerify sequence with the service manual11 lb-ft15 Nm
- Wheel Lug Nuts140 lb-ft190 Nm
Brake Rotor - Front Single7 specs
- Brake Rotor Set Screw7 lb-ft9 Nm
- Caliper Bracket Bolts163 lb-ft221 Nm
- Caliper Bracket Bolts - FrontThreadlocker recommended. Verify sequence with the service manual163 lb-ft221 Nm
- Caliper Mounting BoltsUse thread locker88 lb-ft119 Nm
- Caliper Slide Pin BoltsApply silicone brake grease. Verify sequence with the service manual26 lb-ft35 Nm
- Hub NutIf removed159 lb-ft216 Nm
- Wheel Lug NutsTorque in star pattern. Verify sequence with the service manual140 lb-ft190 Nm
Brake Rotor - Rear Single6 specs
- Brake Rotor Set Screw7 lb-ft9 Nm
- Caliper Bracket Bolts109 lb-ft148 Nm
- Caliper Bracket Bolts - FrontThreadlocker recommended. Verify sequence with the service manual109 lb-ft148 Nm
- Caliper Mounting BoltsUse thread locker88 lb-ft119 Nm
- Caliper Slide Pin BoltsApply silicone brake grease. Verify sequence with the service manual26 lb-ft35 Nm
- Wheel Lug NutsTorque in star pattern. Verify sequence with the service manual140 lb-ft190 Nm
Brake Rotors - Front Pair7 specs
- Brake Rotor Set Screw7 lb-ft9 Nm
- Caliper Bracket Bolts163 lb-ft221 Nm
- Caliper Bracket Bolts - FrontThreadlocker recommended. Verify sequence with the service manual163 lb-ft221 Nm
- Caliper Mounting Bolts88 lb-ft119 Nm
- Caliper Slide Pin BoltsApply silicone brake grease. Verify sequence with the service manual26 lb-ft35 Nm
- Hub NutIf removed159 lb-ft216 Nm
- Wheel Lug NutsTorque in star pattern. Verify sequence with the service manual140 lb-ft190 Nm
Brake Rotors - Rear Pair6 specs
- Brake Rotor Set Screw7 lb-ft9 Nm
- Caliper Bracket Bolts109 lb-ft148 Nm
- Caliper Bracket Bolts - FrontThreadlocker recommended. Verify sequence with the service manual109 lb-ft148 Nm
- Caliper Mounting Bolts88 lb-ft119 Nm
- Caliper Slide Pin BoltsApply silicone brake grease. Verify sequence with the service manual26 lb-ft35 Nm
- Wheel Lug NutsTorque in star pattern. Verify sequence with the service manual140 lb-ft190 Nm
Drum Brake Hardware Kit2 specs
- Caliper Mounting Bolts88 lb-ft119 Nm
- Wheel Lug NutsTorque in star pattern. Verify sequence with the service manual140 lb-ft190 Nm
Drum Brake Shoes - Rear3 specs
- Caliper Bracket Bolts - FrontThreadlocker recommended. Verify sequence with the service manual109 lb-ft148 Nm
- Caliper Mounting Bolts88 lb-ft119 Nm
- Wheel Lug NutsTorque in star pattern. Verify sequence with the service manual140 lb-ft190 Nm
Electronic Parking Brake Motor3 specs
- Caliper Mounting BoltsUse thread locker88 lb-ft119 Nm
- Caliper Slide Pin BoltsApply silicone brake grease. Verify sequence with the service manual26 lb-ft35 Nm
- Wheel Lug NutsTorque in star pattern. Verify sequence with the service manual140 lb-ft190 Nm
Front Brake Pad Replacement3 specs
- Caliper Bracket BoltsThreadlocker recommended88 lb-ft120 Nm
- Caliper Slide Pin BoltsApply silicone brake grease26 lb-ft35 Nm
- Wheel Lug NutsTorque in star pattern140 lb-ft190 Nm
Parking Brake Actuator3 specs
- Caliper Mounting Bolts88 lb-ft119 Nm
- Caliper Slide Pin BoltsApply silicone brake grease. Verify sequence with the service manual26 lb-ft35 Nm
- Wheel Lug NutsTorque in star pattern. Verify sequence with the service manual140 lb-ft190 Nm
Parking Brake Cable5 specs
- Bleeder Screw14 lb-ft18 Nm
- Cable Bracket BoltsVerify sequence with the service manual9 lb-ft12 Nm
- Caliper Mounting Bolts88 lb-ft119 Nm
- Equalizer NutAdjust for proper tension. Verify sequence with the service manual11 lb-ft15 Nm
- Wheel Lug Nuts140 lb-ft190 Nm
Parking Brake Shoes5 specs
- Adjuster LockVerify sequence with the service manual4 lb-ft5 Nm
- Bleeder Screw14 lb-ft18 Nm
- Caliper Mounting Bolts88 lb-ft119 Nm
- Hold-Down SpringsVerify sequence with the service manual6 lb-ft8 Nm
- Wheel Lug NutsTorque in star pattern. Verify sequence with the service manual140 lb-ft190 Nm
Rear Brake Shoe Replacement3 specs
- Backing Plate Bolts44 lb-ft60 Nm
- Wheel Cylinder Bolts9 lb-ft12 Nm
- Wheel Lug NutsTorque in star pattern140 lb-ft190 Nm
Wheel Cylinder3 specs
- Bleeder ScrewDo not overtighten7 lb-ft10 Nm
- Caliper Mounting BoltsUse thread locker88 lb-ft119 Nm
- Wheel Lug NutsTorque in star pattern140 lb-ft190 Nm
Engine
Camshaft Position Sensor5 specs
- Camshaft Position Sensor7 lb-ft10 Nm
- Electrical Connector Bolts7 lb-ft9 Nm
- Gasket Surface BoltsClean mating surfaces20 lb-ft27 Nm
- Sensor Mounting Bolts11 lb-ft15 Nm
- Valve Cover BoltsTighten in sequence7 lb-ft10 Nm
Camshaft R&R5 specs
- Camshaft Retainer PlateTorx bolts18 lb-ft25 Nm
- Camshaft Sprocket Bolts (3-Bolt)For 3-bolt cam gear. If 1-bolt VVT: 55 lb-ft + 50 degrees26 lb-ft35 Nm
- Electrical Connector Bolts7 lb-ft9 Nm
- Gasket Surface BoltsClean mating surfaces20 lb-ft27 Nm
- Sensor Mounting Bolts11 lb-ft15 Nm
Connecting Rod Bearings4 specs
- Connecting Rod BoltsPass 1: 15 lb-ft. Pass 2: 85 degrees. Cracked cap design15 lb-ft + 85°20 Nm
- Electrical Connector Bolts7 lb-ft9 Nm
- Gasket Surface BoltsClean mating surfaces20 lb-ft27 Nm
- Sensor Mounting Bolts11 lb-ft15 Nm
Crankshaft Position Sensor4 specs
- Crankshaft Position Sensor7 lb-ft10 Nm
- Electrical Connector Bolts7 lb-ft9 Nm
- Gasket Surface BoltsClean mating surfaces20 lb-ft27 Nm
- Sensor Mounting Bolts11 lb-ft15 Nm
Crankshaft R&R20 specs
- Connecting Rod BoltsTTY - critical torque plus angle33 lb-ft45 Nm
- Crankshaft Pulley BoltOften TTY, may need impact133 lb-ft180 Nm
- Cylinder Head BoltsTTY - tighten in sequence plus angle48 lb-ft65 Nm
- Electrical Connector Bolts7 lb-ft9 Nm
- Flexplate BoltsAutomatic transmissions63 lb-ft85 Nm
- Flywheel BoltsOften TTY, tighten in star pattern70 lb-ft95 Nm
- Front Main Seal Housing9 lb-ft12 Nm
- Gasket Surface BoltsClean mating surfaces20 lb-ft27 Nm
- Main Bearing Cap BoltsTTY - tighten in sequence plus angle55 lb-ft75 Nm
- Oil Drain PlugUse new crush washer26 lb-ft35 Nm
- Oil Pan BoltTighten in sequence9 lb-ft12 Nm
- Oil Pump Bolts9 lb-ft12 Nm
- Oil Pump Pickup Tube9 lb-ft12 Nm
- Rear Main Seal Housing9 lb-ft12 Nm
- Sensor Mounting Bolts11 lb-ft15 Nm
- Timing Chain Guide BoltsReplace if worn9 lb-ft12 Nm
- Timing Chain Tensioner BoltInstall with pin/clip to compress18 lb-ft25 Nm
- Timing Cover Bolts - 10mmTighten in sequence33 lb-ft45 Nm
- Timing Cover Bolts - 8mmTighten in sequence18 lb-ft25 Nm
- Transmission-to-Engine Bolts41 lb-ft55 Nm
Cylinder Head R&R5 specs
- Cylinder Head Bolts (M11)TTY Bolts. Step 1: 22 lb-ft. Step 2: 90 deg. Step 3: 90 deg. Spiral sequence22 lb-ft + 180°30 Nm
- Cylinder Head Bolts (M8)Upper row small bolts. Tighten to 22 lb-ft in sequence (inner to outer)22 lb-ft30 Nm
- Electrical Connector Bolts7 lb-ft9 Nm
- Gasket Surface BoltsClean mating surfaces20 lb-ft27 Nm
- Sensor Mounting Bolts11 lb-ft15 Nm
Cylinder Head Resurface7 specs
- Cylinder Head BoltsTTY - tighten in sequence plus angle48 lb-ft65 Nm
- Electrical Connector Bolts7 lb-ft9 Nm
- Exhaust Manifold NutsApply anti-seize, work hot-to-cold22 lb-ft30 Nm
- Gasket Surface BoltsClean mating surfaces20 lb-ft27 Nm
- Intake Manifold Bolt18 lb-ft25 Nm
- Sensor Mounting Bolts11 lb-ft15 Nm
- Valve Cover BoltsTighten in sequence7 lb-ft10 Nm
Engine Mount - Front3 specs
- Engine Mount Through-Bolt50 lb-ft68 Nm
- Engine Mount-to-Block Bolts48 lb-ft65 Nm
- Engine Mount-to-Frame Bolts55 lb-ft75 Nm
Engine Mount - Rear6 specs
- Electrical Connector Bolts7 lb-ft9 Nm
- Engine Mount Through-Bolt88 lb-ft119 Nm
- Engine Mount-to-Block Bolts48 lb-ft65 Nm
- Engine Mount-to-Frame Bolts55 lb-ft75 Nm
- Gasket Surface BoltsClean mating surfaces20 lb-ft27 Nm
- Sensor Mounting Bolts11 lb-ft15 Nm
Engine Mounts - All7 specs
- Electrical Connector Bolts7 lb-ft9 Nm
- Engine Mount Through-Bolt63 lb-ft85 Nm
- Engine Mount-to-Block Bolts48 lb-ft65 Nm
- Engine Mount-to-Frame Bolts55 lb-ft75 Nm
- Gasket Surface BoltsClean mating surfaces20 lb-ft27 Nm
- Sensor Mounting Bolts11 lb-ft15 Nm
- Transmission Mount Bolts48 lb-ft65 Nm
Engine R&R13 specs
- AC Compressor Bolts18 lb-ft25 Nm
- Alternator Mounting Bolts37 lb-ft50 Nm
- Electrical Connector Bolts7 lb-ft9 Nm
- Engine Mount-to-Block Bolts48 lb-ft65 Nm
- Engine Mount-to-Frame Bolts55 lb-ft75 Nm
- Exhaust Manifold NutsApply anti-seize, work hot-to-cold22 lb-ft30 Nm
- Flywheel BoltsOften TTY, tighten in star pattern70 lb-ft95 Nm
- Gasket Surface BoltsClean mating surfaces20 lb-ft27 Nm
- Oil Drain PlugUse new crush washer26 lb-ft35 Nm
- Power Steering Pump Bolts18 lb-ft25 Nm
- Sensor Mounting Bolts11 lb-ft15 Nm
- Starter Mounting Bolt37 lb-ft50 Nm
- Transmission-to-Engine Bolts41 lb-ft55 Nm
Engine Rebuild21 specs
- Balance Shaft Bolts18 lb-ft25 Nm
- Camshaft Bearing Cap BoltsTighten in sequence, 3 passes10 lb-ft14 Nm
- Camshaft Cap BoltsTighten in sequence from center outward, multiple passes10 lb-ft14 Nm
- Connecting Rod BoltsTTY - critical torque plus angle33 lb-ft45 Nm
- Crankshaft Pulley BoltOften TTY - check spec, may require impact133 lb-ft180 Nm
- Cylinder Head BoltsTTY - tighten in sequence plus angle48 lb-ft65 Nm
- Electrical Connector Bolts7 lb-ft9 Nm
- Exhaust Manifold NutsApply anti-seize, work hot-to-cold22 lb-ft30 Nm
- Flywheel BoltsOften TTY, tighten in star pattern70 lb-ft95 Nm
- Gasket Surface BoltsClean mating surfaces20 lb-ft27 Nm
- Intake Manifold Bolt18 lb-ft25 Nm
- Main Bearing Cap BoltsTTY - tighten in sequence plus angle55 lb-ft75 Nm
- Oil Drain PlugUse new crush washer26 lb-ft35 Nm
- Oil Pan BoltTighten in sequence9 lb-ft12 Nm
- Oil Pump Bolts9 lb-ft12 Nm
- Oil Pump Pickup Tube9 lb-ft12 Nm
- Sensor Mounting Bolts11 lb-ft15 Nm
- Timing Chain Guide BoltsReplace if worn9 lb-ft12 Nm
- Timing Chain Tensioner BoltInstall with pin/clip to compress18 lb-ft25 Nm
- Timing Cover Bolts - 8mmTighten in sequence18 lb-ft25 Nm
- Valve Cover BoltsTighten in sequence7 lb-ft10 Nm
Exhaust Manifold9 specs
- EGR Tube Fitting46 lb-ft62 Nm
- Electrical Connector Bolts7 lb-ft9 Nm
- Exhaust Manifold BoltsCenter-out sequence18 lb-ft25 Nm
- Exhaust Manifold NutsApply anti-seize32 lb-ft43 Nm
- Gasket Surface BoltsClean mating surfaces20 lb-ft27 Nm
- Hanger Bolts20 lb-ft27 Nm
- Heat Shield Bolts13 lb-ft18 Nm
- O2 SensorApply anti-seize to threads46 lb-ft62 Nm
- Sensor Mounting Bolts11 lb-ft15 Nm
Exhaust Manifold Gasket3 specs
- Exhaust Manifold NutsApply anti-seize, work hot-to-cold22 lb-ft30 Nm
- Exhaust Manifold StudsIf replacing studs11 lb-ft15 Nm
- Heat Shield Bolts7 lb-ft10 Nm
Fan Belt Replacement3 specs
- Idler Pulley Bolt30 lb-ft40 Nm
- Tensioner Bolt18 lb-ft25 Nm
- Tensioner Pulley Bolt33 lb-ft45 Nm
Flexplate6 specs
- Electrical Connector Bolts7 lb-ft9 Nm
- Flexplate BoltsAutomatic transmissions. Verify sequence with the service manual63 lb-ft85 Nm
- Gasket Surface BoltsClean mating surfaces20 lb-ft27 Nm
- Sensor Mounting Bolts11 lb-ft15 Nm
- Torque Converter BoltsVerify sequence with the service manual37 lb-ft50 Nm
- Transmission-to-Engine BoltsVerify sequence with the service manual41 lb-ft55 Nm
Flywheel6 specs
- Drain PlugUse new washer34 lb-ft46 Nm
- Fill Plug34 lb-ft46 Nm
- Flexplate BoltsAutomatic transmissions63 lb-ft85 Nm
- Flywheel BoltsOften TTY - check specs, tighten in star pattern70 lb-ft95 Nm
- Transmission Drain PlugUse new crush washer if equipped22 lb-ft30 Nm
- Transmission Pan BoltsTighten in criss-cross pattern9 lb-ft12 Nm
Freeze Plug - Single4 specs
- Electrical Connector Bolts7 lb-ft9 Nm
- Freeze PlugUse sealant on edges7 lb-ft10 Nm
- Gasket Surface BoltsClean mating surfaces20 lb-ft27 Nm
- Sensor Mounting Bolts11 lb-ft15 Nm
Freeze Plugs - All4 specs
- Electrical Connector Bolts7 lb-ft9 Nm
- Freeze PlugUse sealant on edges7 lb-ft10 Nm
- Gasket Surface BoltsClean mating surfaces20 lb-ft27 Nm
- Sensor Mounting Bolts11 lb-ft15 Nm
Front Main Seal8 specs
- Crankshaft Pulley BoltOften TTY - check spec, may require impact133 lb-ft180 Nm
- Electrical Connector Bolts7 lb-ft9 Nm
- Gasket Surface BoltsClean mating surfaces20 lb-ft27 Nm
- Oil Drain PlugUse new crush washer26 lb-ft35 Nm
- Oil Pan BoltFront section only9 lb-ft12 Nm
- Sensor Mounting Bolts11 lb-ft15 Nm
- Timing Cover Bolts - 10mmTighten in sequence33 lb-ft45 Nm
- Timing Cover Bolts - 8mmTighten in sequence18 lb-ft25 Nm
Full Engine Tune-Up5 specs
- Ignition Coil Bolt6 lb-ft8 Nm
- Spark Plugs - Aluminum HeadApply anti-seize to threads15 lb-ft20 Nm
- Spark Plugs - Cast Iron HeadApply anti-seize to threads15 lb-ft20 Nm
- Throttle Body Bolts7 lb-ft10 Nm
- Valve Cover BoltsTighten in sequence7 lb-ft10 Nm
Harmonic Balancer4 specs
- Crankshaft Pulley BoltInstall new bolt: 37 lb-ft + 140 degrees37 lb-ft + 140°50 Nm
- Electrical Connector Bolts7 lb-ft9 Nm
- Gasket Surface BoltsClean mating surfaces20 lb-ft27 Nm
- Sensor Mounting Bolts11 lb-ft15 Nm
Head Gasket - Single6 specs
- Exhaust Manifold NutsApply anti-seize18 lb-ft25 Nm
- Intake Manifold BoltTighten in sequence18 lb-ft25 Nm
- Cylinder Head Bolts - Step 1Always use new TTY bolts22 lb-ft30 Nm
- Cylinder Head Bolts - Step 2Tighten in sequence59 lb-ft80 Nm
- Cylinder Head Bolts - Step 3Plus 90 degreesTurn 90°
- Cylinder Head Bolts - Step 4Plus 90 degreesTurn 90°
Head Gaskets - Both10 specs
- Camshaft Cap BoltsTorque sequence16 lb-ft22 Nm
- Cylinder Head BoltsMulti-step + angle88 lb-ft119 Nm
- Cylinder Head Bolts (M11)TTY Bolts. Step 1: 22 lb-ft. Step 2: 90 deg. Step 3: 90 deg. Spiral sequence22 lb-ft + 180°30 Nm
- Cylinder Head Bolts (M8)Upper row small bolts. Tighten to 22 lb-ft in sequence (inner to outer)22 lb-ft30 Nm
- Electrical Connector Bolts7 lb-ft9 Nm
- Exhaust Manifold Nuts34 lb-ft46 Nm
- Gasket Surface BoltsClean mating surfaces20 lb-ft27 Nm
- Intake Manifold Bolt24 lb-ft33 Nm
- Sensor Mounting Bolts11 lb-ft15 Nm
- Valve Cover Bolts14 lb-ft18 Nm
Idle Air Control Valve4 specs
- Electrical Connector Bolts7 lb-ft9 Nm
- Gasket Surface BoltsClean mating surfaces20 lb-ft27 Nm
- IAC Valve Screws2 lb-ft3 Nm
- Sensor Mounting Bolts11 lb-ft15 Nm
Idler Pulley4 specs
- Electrical Connector Bolts7 lb-ft9 Nm
- Gasket Surface BoltsClean mating surfaces20 lb-ft27 Nm
- Idler Pulley Bolt33 lb-ft45 Nm
- Sensor Mounting Bolts11 lb-ft15 Nm
Intake Manifold6 specs
- Electrical Connector Bolts7 lb-ft9 Nm
- Fuel Rail Bolts20 lb-ft27 Nm
- Gasket Surface BoltsClean mating surfaces20 lb-ft27 Nm
- Intake Manifold BoltPlastic: 44 lb-in first pass, 89 lb-in final pass. Spiral sequence7.4 lb-ft10 Nm
- Sensor Mounting Bolts11 lb-ft15 Nm
- Throttle Body Bolts14 lb-ft18 Nm
Intake Manifold Gasket3 specs
- Fuel Rail Bolts9 lb-ft12 Nm
- Intake Manifold BoltTighten in sequence from center out8 lb-ft11 Nm
- Throttle Body Bolts7 lb-ft10 Nm
Knock Sensor4 specs
- Electrical Connector Bolts7 lb-ft9 Nm
- Gasket Surface BoltsClean mating surfaces20 lb-ft27 Nm
- Knock SensorTorque critical for function15 lb-ft20 Nm
- Sensor Mounting Bolts11 lb-ft15 Nm
Lifter - Single7 specs
- Electrical Connector Bolts7 lb-ft9 Nm
- Gasket Surface BoltsClean mating surfaces20 lb-ft27 Nm
- Intake Manifold Bolt18 lb-ft25 Nm
- Rocker Arm BoltsTighten with cam lobe pointing away22 lb-ft30 Nm
- Rocker Arm Shaft BoltsTighten evenly in sequence18 lb-ft25 Nm
- Sensor Mounting Bolts11 lb-ft15 Nm
- Valve Cover BoltsTighten in sequence7 lb-ft10 Nm
Lifters/Tappets - All10 specs
- Camshaft Bearing Cap BoltsTighten in sequence, 3 passes10 lb-ft14 Nm
- Camshaft Cap BoltsTighten in sequence from center outward, multiple passes10 lb-ft14 Nm
- Camshaft Position Sensor7 lb-ft10 Nm
- Electrical Connector Bolts7 lb-ft9 Nm
- Gasket Surface BoltsClean mating surfaces20 lb-ft27 Nm
- Intake Manifold Bolt18 lb-ft25 Nm
- Rocker Arm BoltsTighten with cam lobe pointing away22 lb-ft30 Nm
- Rocker Arm Shaft BoltsTighten evenly in sequence18 lb-ft25 Nm
- Sensor Mounting Bolts11 lb-ft15 Nm
- Valve Cover BoltsTighten in sequence7 lb-ft10 Nm
Long Block Replacement16 specs
- Camshaft Cap BoltsTighten in sequence from center outward, multiple passes10 lb-ft14 Nm
- Connecting Rod BoltsTTY - critical torque plus angle33 lb-ft45 Nm
- Cylinder Head BoltsTTY - tighten in sequence plus angle48 lb-ft65 Nm
- Electrical Connector Bolts7 lb-ft9 Nm
- Exhaust Manifold NutsApply anti-seize, work hot-to-cold22 lb-ft30 Nm
- Flywheel BoltsOften TTY, tighten in star pattern70 lb-ft95 Nm
- Gasket Surface BoltsClean mating surfaces20 lb-ft27 Nm
- Intake Manifold Bolt18 lb-ft25 Nm
- Main Bearing Cap BoltsTTY - tighten in sequence plus angle55 lb-ft75 Nm
- Oil Drain PlugUse new crush washer26 lb-ft35 Nm
- Oil Pan Bolt9 lb-ft12 Nm
- Sensor Mounting Bolts11 lb-ft15 Nm
- Timing Chain Tensioner BoltInstall with pin/clip to compress18 lb-ft25 Nm
- Timing Cover Bolts - 8mmTighten in sequence18 lb-ft25 Nm
- Transmission-to-Engine Bolts41 lb-ft55 Nm
- Valve Cover BoltsTighten in sequence7 lb-ft10 Nm
Main Bearings5 specs
- Electrical Connector Bolts7 lb-ft9 Nm
- Gasket Surface BoltsClean mating surfaces20 lb-ft27 Nm
- Main Cap Bolts (Inner/Outer M10)Pass 1: 15 lb-ft. Pass 2: 80 degrees. Inner then outer15 lb-ft + 80°20 Nm
- Main Cap Side Bolts (M8)Tighten side bolts last18 lb-ft25 Nm
- Sensor Mounting Bolts11 lb-ft15 Nm
Manifold Absolute Pressure Sensor4 specs
- Electrical Connector Bolts7 lb-ft9 Nm
- Gasket Surface BoltsClean mating surfaces20 lb-ft27 Nm
- MAP Sensor Screws2 lb-ft3 Nm
- Sensor Mounting Bolts11 lb-ft15 Nm
Mass Air Flow Sensor5 specs
- Air Intake Clamps2 lb-ft3 Nm
- Electrical Connector Bolts7 lb-ft9 Nm
- Gasket Surface BoltsClean mating surfaces20 lb-ft27 Nm
- MAF Sensor Screws2 lb-ft3 Nm
- Sensor Mounting Bolts11 lb-ft15 Nm
Oil Change2 specs
- Oil Drain PlugUse new crush washer18 lb-ft25 Nm
- Oil Filter (Spin-On)Hand tight plus 3/4 turn22 lb-ft30 Nm
Oil Level Sensor5 specs
- Electrical Connector Bolts7 lb-ft9 Nm
- Gasket Surface BoltsClean mating surfaces20 lb-ft27 Nm
- Oil Level Sensor11 lb-ft15 Nm
- Oil Pan BoltIf access needed9 lb-ft12 Nm
- Sensor Mounting Bolts11 lb-ft15 Nm
Oil Pan Gasket2 specs
- Oil Drain PlugUse new crush washer18 lb-ft25 Nm
- Oil Pan BoltTighten in sequence from center outward18 lb-ft25 Nm
Oil Pan Replacement6 specs
- Electrical Connector Bolts7 lb-ft9 Nm
- Gasket Surface BoltsClean mating surfaces20 lb-ft27 Nm
- Oil Drain PlugUse new crush washer26 lb-ft35 Nm
- Oil Pan BoltTighten in sequence9 lb-ft12 Nm
- Oil Pump Pickup Tube9 lb-ft12 Nm
- Sensor Mounting Bolts11 lb-ft15 Nm
Oil Pressure Sensor4 specs
- Electrical Connector Bolts7 lb-ft9 Nm
- Gasket Surface BoltsClean mating surfaces20 lb-ft27 Nm
- Oil Pressure SensorUse thread sealant15 lb-ft20 Nm
- Sensor Mounting Bolts11 lb-ft15 Nm
Oil Pump8 specs
- Electrical Connector Bolts7 lb-ft9 Nm
- Gasket Surface BoltsClean mating surfaces20 lb-ft27 Nm
- Oil Drain PlugUse new crush washer26 lb-ft35 Nm
- Oil Pan Bolt9 lb-ft12 Nm
- Oil Pump Bolts9 lb-ft12 Nm
- Oil Pump Pickup Tube9 lb-ft12 Nm
- Sensor Mounting Bolts11 lb-ft15 Nm
- Timing Cover Bolts - 8mmTighten in sequence18 lb-ft25 Nm
PCV Valve4 specs
- Electrical Connector Bolts7 lb-ft9 Nm
- Gasket Surface BoltsClean mating surfaces20 lb-ft27 Nm
- PCV ValveHand tight usually6 lb-ft8 Nm
- Sensor Mounting Bolts11 lb-ft15 Nm
Piston - Single7 specs
- Connecting Rod BoltsTTY - critical torque plus angle33 lb-ft45 Nm
- Cylinder Head BoltsTTY - tighten in sequence plus angle48 lb-ft65 Nm
- Electrical Connector Bolts7 lb-ft9 Nm
- Gasket Surface BoltsClean mating surfaces20 lb-ft27 Nm
- Oil Drain PlugUse new crush washer26 lb-ft35 Nm
- Oil Pan Bolt9 lb-ft12 Nm
- Sensor Mounting Bolts11 lb-ft15 Nm
Piston Rings - All9 specs
- Connecting Rod BoltsTTY - critical torque plus angle33 lb-ft45 Nm
- Cylinder Head BoltsTTY - tighten in sequence plus angle48 lb-ft65 Nm
- Electrical Connector Bolts7 lb-ft9 Nm
- Gasket Surface BoltsClean mating surfaces20 lb-ft27 Nm
- Main Bearing Cap BoltsTTY - tighten in sequence plus angle55 lb-ft75 Nm
- Oil Drain PlugUse new crush washer26 lb-ft35 Nm
- Oil Pan BoltTighten in sequence9 lb-ft12 Nm
- Oil Pump Pickup Tube9 lb-ft12 Nm
- Sensor Mounting Bolts11 lb-ft15 Nm
Pistons - All9 specs
- Connecting Rod BoltsTTY - critical torque plus angle33 lb-ft45 Nm
- Cylinder Head BoltsTTY - tighten in sequence plus angle48 lb-ft65 Nm
- Electrical Connector Bolts7 lb-ft9 Nm
- Gasket Surface BoltsClean mating surfaces20 lb-ft27 Nm
- Main Bearing Cap BoltsTTY - tighten in sequence plus angle55 lb-ft75 Nm
- Oil Drain PlugUse new crush washer26 lb-ft35 Nm
- Oil Pan Bolt9 lb-ft12 Nm
- Oil Pump Pickup Tube9 lb-ft12 Nm
- Sensor Mounting Bolts11 lb-ft15 Nm
Rear Main Seal9 specs
- Electrical Connector Bolts7 lb-ft9 Nm
- Flexplate BoltsAutomatic transmissions63 lb-ft85 Nm
- Flywheel BoltsOften TTY, tighten in star pattern70 lb-ft95 Nm
- Gasket Surface BoltsClean mating surfaces20 lb-ft27 Nm
- Oil Drain PlugUse new crush washer26 lb-ft35 Nm
- Oil Pan BoltRear section9 lb-ft12 Nm
- Rear Main Seal Housing9 lb-ft12 Nm
- Sensor Mounting Bolts11 lb-ft15 Nm
- Transmission-to-Engine Bolts41 lb-ft55 Nm
Rocker Arms - All4 specs
- Electrical Connector Bolts7 lb-ft9 Nm
- Gasket Surface BoltsClean mating surfaces20 lb-ft27 Nm
- Rocker Arm BoltsEnsure cylinder is at TDC compression to avoid loading valve22 lb-ft30 Nm
- Sensor Mounting Bolts11 lb-ft15 Nm
Serpentine Belt2 specs
- Belt Tensioner Bolt41 lb-ft55 Nm
- Idler Pulley Bolt33 lb-ft45 Nm
Serpentine Belt Tensioner4 specs
- Belt Tensioner Bolt41 lb-ft55 Nm
- Electrical Connector Bolts7 lb-ft9 Nm
- Gasket Surface BoltsClean mating surfaces20 lb-ft27 Nm
- Sensor Mounting Bolts11 lb-ft15 Nm
Short Block Replacement12 specs
- Connecting Rod BoltsTTY - critical torque plus angle33 lb-ft45 Nm
- Crankshaft Pulley BoltOften TTY - check spec, may require impact133 lb-ft180 Nm
- Electrical Connector Bolts7 lb-ft9 Nm
- Flywheel BoltsOften TTY, tighten in star pattern70 lb-ft95 Nm
- Gasket Surface BoltsClean mating surfaces20 lb-ft27 Nm
- Main Bearing Cap BoltsTTY - tighten in sequence plus angle55 lb-ft75 Nm
- Oil Drain PlugUse new crush washer26 lb-ft35 Nm
- Oil Pan Bolt9 lb-ft12 Nm
- Oil Pump Bolts9 lb-ft12 Nm
- Sensor Mounting Bolts11 lb-ft15 Nm
- Timing Cover Bolts - 8mmTighten in sequence18 lb-ft25 Nm
- Transmission-to-Engine Bolts41 lb-ft55 Nm
Throttle Body2 specs
- Air Intake Hose Clamps2 lb-ft3 Nm
- Throttle Body Bolts7 lb-ft10 Nm
Throttle Position Sensor4 specs
- Electrical Connector Bolts7 lb-ft9 Nm
- Gasket Surface BoltsClean mating surfaces20 lb-ft27 Nm
- Sensor Mounting Bolts11 lb-ft15 Nm
- TPS Screws2 lb-ft3 Nm
Timing Chain5 specs
- Camshaft Sprocket Bolts26 lb-ft35 Nm
- Crankshaft Pulley BoltOften TTY - check specs133 lb-ft + 90°180 Nm
- Timing Chain Guide Bolts9 lb-ft12 Nm
- Timing Chain Tensioner18 lb-ft25 Nm
- Timing Cover BoltTighten in sequence9 lb-ft12 Nm
Timing Chain Guide11 specs
- Camshaft Sprocket Bolts74 lb-ft101 Nm
- Crankshaft Pulley Bolt176 lb-ft238 Nm
- Electrical Connector Bolts7 lb-ft9 Nm
- Gasket Surface BoltsClean mating surfaces20 lb-ft27 Nm
- Guide Bolts24 lb-ft33 Nm
- Sensor Mounting Bolts11 lb-ft15 Nm
- Tensioner Bolt20 lb-ft27 Nm
- Timing Chain Guide BoltsReplace if worn9 lb-ft12 Nm
- Timing Cover Bolt14 lb-ft18 Nm
- Timing Cover Bolts - 8mmTighten in sequence18 lb-ft25 Nm
- Valve Cover BoltsTighten in sequence7 lb-ft10 Nm
Timing Chain Kit4 specs
- Camshaft Sprocket Bolts26 lb-ft35 Nm
- Crankshaft balancer bolt (single-use, 240Nm + 60°)177 lb-ft240 Nm
- Front cover bolts18 lb-ft25 Nm
- Oil pan front bolts18 lb-ft25 Nm
Timing Chain Tensioner3 specs
- Tensioner Cap/PlugUse new crush washer if equipped22 lb-ft30 Nm
- Tensioner Housing BoltsTighten in sequence18 lb-ft25 Nm
- Timing Cover Access Bolts9 lb-ft12 Nm
Transmission Mount7 specs
- Crossmember Bolt70 lb-ft95 Nm
- Drain PlugUse new washer34 lb-ft46 Nm
- Fill Plug34 lb-ft46 Nm
- Flywheel BoltsOften TTY, tighten in star pattern70 lb-ft95 Nm
- Transmission Drain PlugUse new crush washer if equipped22 lb-ft30 Nm
- Transmission Mount Bolts48 lb-ft65 Nm
- Transmission Pan BoltsTighten in criss-cross pattern9 lb-ft12 Nm
Valve Adjustment6 specs
- Electrical Connector Bolts7 lb-ft9 Nm
- Gasket Surface BoltsClean mating surfaces20 lb-ft27 Nm
- Rocker Arm BoltsTighten with cam lobe pointing away22 lb-ft30 Nm
- Sensor Mounting Bolts11 lb-ft15 Nm
- Valve Cover BoltsTighten in sequence7 lb-ft10 Nm
- Valve Lash Adjusting Screw Lock NutHold screw while tightening15 lb-ft20 Nm
Valve Cover Gasket - Single2 specs
- Spark Plug Tube SealsIf equipped with separate seals9 lb-ft12 Nm
- Valve Cover BoltsTighten in sequence7 lb-ft10 Nm
Valve Cover Gaskets - Both7 specs
- Electrical Connector Bolts7 lb-ft9 Nm
- Gasket Surface BoltsClean mating surfaces20 lb-ft27 Nm
- Ignition Coil Bolt6 lb-ft8 Nm
- Intake Manifold BoltIf required18 lb-ft25 Nm
- Sensor Mounting Bolts11 lb-ft15 Nm
- Spark Plugs - Aluminum HeadApply anti-seize to threads15 lb-ft20 Nm
- Valve Cover BoltsTighten in sequence7 lb-ft10 Nm
Valve Job - Complete12 specs
- Camshaft Cap BoltsTighten in sequence from center outward, multiple passes10 lb-ft14 Nm
- Camshaft Sprocket BoltsHold cam with wrench on hex59 lb-ft80 Nm
- Cylinder Head BoltsTTY - tighten in sequence plus angle48 lb-ft65 Nm
- Electrical Connector Bolts7 lb-ft9 Nm
- Exhaust Manifold NutsApply anti-seize, work hot-to-cold22 lb-ft30 Nm
- Gasket Surface BoltsClean mating surfaces20 lb-ft27 Nm
- Intake Manifold Bolt18 lb-ft25 Nm
- Rocker Arm BoltsTighten with cam lobe pointing away22 lb-ft30 Nm
- Sensor Mounting Bolts11 lb-ft15 Nm
- Timing Chain Tensioner BoltInstall with pin/clip to compress18 lb-ft25 Nm
- Timing Cover Bolts - 8mmTighten in sequence18 lb-ft25 Nm
- Valve Cover BoltsTighten in sequence7 lb-ft10 Nm
Valve Seals8 specs
- Camshaft Cap BoltsTighten in sequence from center outward, multiple passes10 lb-ft14 Nm
- Electrical Connector Bolts7 lb-ft9 Nm
- Gasket Surface BoltsClean mating surfaces20 lb-ft27 Nm
- Rocker Arm BoltsTighten with cam lobe pointing away22 lb-ft30 Nm
- Rocker Arm Shaft BoltsTighten evenly in sequence18 lb-ft25 Nm
- Sensor Mounting Bolts11 lb-ft15 Nm
- Spark Plugs - Aluminum HeadApply anti-seize to threads15 lb-ft20 Nm
- Valve Cover BoltsTighten in sequence7 lb-ft10 Nm
Valve Spring - Single6 specs
- Electrical Connector Bolts7 lb-ft9 Nm
- Gasket Surface BoltsClean mating surfaces20 lb-ft27 Nm
- Rocker Arm BoltsTighten with cam lobe pointing away22 lb-ft30 Nm
- Sensor Mounting Bolts11 lb-ft15 Nm
- Spark Plugs - Aluminum HeadApply anti-seize to threads15 lb-ft20 Nm
- Valve Cover BoltsTighten in sequence7 lb-ft10 Nm
Valve Springs - All8 specs
- Camshaft Cap BoltsTighten in sequence from center outward, multiple passes10 lb-ft14 Nm
- Electrical Connector Bolts7 lb-ft9 Nm
- Gasket Surface BoltsClean mating surfaces20 lb-ft27 Nm
- Rocker Arm BoltsTighten with cam lobe pointing away22 lb-ft30 Nm
- Rocker Arm Shaft BoltsTighten evenly in sequence18 lb-ft25 Nm
- Sensor Mounting Bolts11 lb-ft15 Nm
- Spark Plugs - Aluminum HeadApply anti-seize to threads15 lb-ft20 Nm
- Valve Cover BoltsTighten in sequence7 lb-ft10 Nm
Cooling
Coolant Bypass Pipe8 specs
- Bleed ScrewOpen during fill7 lb-ft9 Nm
- Coolant Drain Plug11 lb-ft15 Nm
- Drain PetcockHand tight7 lb-ft9 Nm
- Fan Bolts11 lb-ft15 Nm
- Hose Clamps2 lb-ft3 Nm
- Pump Bolts24 lb-ft33 Nm
- Thermostat Housing Bolt11 lb-ft15 Nm
- Water Pump BoltsTighten in criss-cross pattern18 lb-ft25 Nm
Coolant Flush12 specs
- Air Box Clips4 lb-ft5 Nm
- Bleed ScrewOpen during fill6 lb-ft8 Nm
- Block Drain PlugIf equipped, use new washer18 lb-ft25 Nm
- Connector Bolts7 lb-ft9 Nm
- Coolant Hose Clamps4 lb-ft5 Nm
- Drain Petcock4 lb-ft5 Nm
- Drain Plug11 lb-ft15 Nm
- Hose Clamps4 lb-ft5 Nm
- Oil Drain PlugUse new crush washer26 lb-ft35 Nm
- Pump Bolts24 lb-ft33 Nm
- Radiator CapHand tight1 lb-ft1 Nm
- Wheel Lug NutsTorque in star pattern140 lb-ft190 Nm
Coolant Reservoir9 specs
- Bleed ScrewOpen during fill7 lb-ft9 Nm
- Coolant Drain Plug11 lb-ft15 Nm
- Drain PetcockHand tight7 lb-ft9 Nm
- Fan Bolts11 lb-ft15 Nm
- Hose ClampsDo not overtighten4 lb-ft5 Nm
- Pump Bolts24 lb-ft33 Nm
- Reservoir Mounting Bolts6 lb-ft8 Nm
- Thermostat Housing Bolt14 lb-ft19 Nm
- Water Pump BoltsTighten in criss-cross pattern18 lb-ft25 Nm
Coolant Temperature Sensor7 specs
- Bleed ScrewOpen during fill7 lb-ft9 Nm
- Coolant Drain Plug11 lb-ft15 Nm
- Drain PetcockHand tight7 lb-ft9 Nm
- Fan Bolts11 lb-ft15 Nm
- Hose Clamps2 lb-ft3 Nm
- Pump BoltsTorque in sequence24 lb-ft33 Nm
- Thermostat Housing Bolt11 lb-ft15 Nm
Cooling Fan Assembly6 specs
- Coolant Drain Plug11 lb-ft15 Nm
- Drain PetcockHand tight7 lb-ft9 Nm
- Fan Bolts11 lb-ft15 Nm
- Hose Clamps2 lb-ft3 Nm
- Pump BoltsTorque in sequence24 lb-ft33 Nm
- Thermostat Housing Bolt11 lb-ft15 Nm
Cooling Fan Clutch5 specs
- Drain PetcockHand tight7 lb-ft9 Nm
- Fan Bolts11 lb-ft15 Nm
- Hose Clamps2 lb-ft3 Nm
- Pump Bolts24 lb-ft33 Nm
- Thermostat Housing Bolt11 lb-ft15 Nm
Cooling Fan Motor7 specs
- Drain PetcockHand tight7 lb-ft9 Nm
- Electrical Connector4 lb-ft5 Nm
- Fan Bolts11 lb-ft15 Nm
- Fan Motor Bolts6 lb-ft8 Nm
- Hose Clamps4 lb-ft5 Nm
- Pump BoltsTorque in sequence24 lb-ft33 Nm
- Thermostat Housing Bolt14 lb-ft19 Nm
Cooling Fan Relay4 specs
- Drain PetcockHand tight7 lb-ft9 Nm
- Fan Bolts11 lb-ft15 Nm
- Pump BoltsTorque in sequence24 lb-ft33 Nm
- Thermostat Housing Bolt11 lb-ft15 Nm
Engine Oil Cooler6 specs
- Coolant Drain Plug11 lb-ft15 Nm
- Drain PetcockHand tight7 lb-ft9 Nm
- Fan Bolts11 lb-ft15 Nm
- Hose Clamps2 lb-ft3 Nm
- Pump Bolts24 lb-ft33 Nm
- Thermostat Housing Bolt11 lb-ft15 Nm
Heater Control Valve6 specs
- Drain PetcockHand tight7 lb-ft9 Nm
- Fan Bolts11 lb-ft15 Nm
- Hose Clamps2 lb-ft3 Nm
- Pump Bolts24 lb-ft33 Nm
- Thermostat Housing Bolt14 lb-ft19 Nm
- Valve Mounting6 lb-ft8 Nm
Heater Core8 specs
- Dashboard Screws2 lb-ft3 Nm
- Drain PetcockHand tight7 lb-ft9 Nm
- Fan Bolts11 lb-ft15 Nm
- Heater Core Mounting6 lb-ft8 Nm
- Heater Hose Clamps2 lb-ft3 Nm
- Hose Clamps4 lb-ft5 Nm
- Pump BoltsTorque in sequence24 lb-ft33 Nm
- Thermostat Housing Bolt14 lb-ft19 Nm
Heater Hoses6 specs
- Coolant Drain Plug11 lb-ft15 Nm
- Drain PetcockHand tight7 lb-ft9 Nm
- Fan Bolts11 lb-ft15 Nm
- Hose Clamps2 lb-ft3 Nm
- Pump Bolts24 lb-ft33 Nm
- Thermostat Housing Bolt11 lb-ft15 Nm
Radiator4 specs
- Drain PetcockPlastic - hand tight4 lb-ft5 Nm
- Radiator Mounting BoltDo not overtighten plastic mounts9 lb-ft12 Nm
- Transmission Cooler LinesIf equipped18 lb-ft25 Nm
- Upper/Lower Hose Clamps2 lb-ft3 Nm
Radiator Cap4 specs
- Drain PetcockHand tight7 lb-ft9 Nm
- Fan Bolts11 lb-ft15 Nm
- Pump BoltsTorque in sequence24 lb-ft33 Nm
- Thermostat Housing Bolt11 lb-ft15 Nm
Radiator Hose - Lower5 specs
- Drain PetcockHand tight7 lb-ft9 Nm
- Fan Bolts11 lb-ft15 Nm
- Hose Clamps2 lb-ft3 Nm
- Pump Bolts24 lb-ft33 Nm
- Thermostat Housing Bolt14 lb-ft19 Nm
Radiator Hose - Upper5 specs
- Drain PetcockHand tight7 lb-ft9 Nm
- Fan Bolts11 lb-ft15 Nm
- Hose Clamps2 lb-ft3 Nm
- Pump Bolts24 lb-ft33 Nm
- Thermostat Housing Bolt14 lb-ft19 Nm
Radiator Hoses - Both6 specs
- Coolant Drain Plug11 lb-ft15 Nm
- Drain PetcockHand tight7 lb-ft9 Nm
- Fan Bolts11 lb-ft15 Nm
- Hose Clamps2 lb-ft3 Nm
- Pump BoltsTorque in sequence24 lb-ft33 Nm
- Thermostat Housing Bolt11 lb-ft15 Nm
Radiator Removal and Service4 specs
- Drain PetcockPlastic - hand-tight only4 lb-ft5 Nm
- Fan Shroud Bolts7 lb-ft10 Nm
- Radiator Mounting BoltDo not overtighten plastic mounts9 lb-ft12 Nm
- Transmission Cooler LinesIf equipped, use new washers18 lb-ft25 Nm
Thermostat2 specs
- Coolant Temperature SensorUse thread sealant15 lb-ft20 Nm
- Thermostat Housing Bolt11 lb-ft15 Nm
Thermostat Housing8 specs
- Coolant Drain Plug11 lb-ft15 Nm
- Coolant Hose Clamps4 lb-ft5 Nm
- Drain PetcockHand tight7 lb-ft9 Nm
- Fan Bolts11 lb-ft15 Nm
- Hose Clamps2 lb-ft3 Nm
- Pump Bolts24 lb-ft33 Nm
- Thermostat Housing Bolt11 lb-ft15 Nm
- Water Pump BoltsTighten in criss-cross pattern18 lb-ft25 Nm
Water Pump3 specs
- Hose ClampsSpring clamps preferred2 lb-ft3 Nm
- Thermostat Housing Bolt11 lb-ft15 Nm
- Water Pump BoltsTighten in criss-cross pattern22 lb-ft30 Nm
Ignition
Ignition Coil - Single3 specs
- Connector Bolts7 lb-ft9 Nm
- Ignition Coil Bolt6 lb-ft8 Nm
- Spark Plugs - Aluminum HeadApply anti-seize to threads15 lb-ft20 Nm
Ignition Coils - All3 specs
- Connector Bolts7 lb-ft9 Nm
- Ignition Coil Bolt6 lb-ft8 Nm
- Spark Plugs - Aluminum HeadApply anti-seize to threads15 lb-ft20 Nm
Ignition Control Module3 specs
- Connector Bolts7 lb-ft9 Nm
- Ignition Coil Bolt6 lb-ft8 Nm
- Spark Plugs - Aluminum HeadApply anti-seize to threads15 lb-ft20 Nm
Ignition Lock Cylinder3 specs
- Connector Bolts7 lb-ft9 Nm
- Ignition Coil Bolt6 lb-ft8 Nm
- Spark Plugs - Aluminum HeadApply anti-seize to threads15 lb-ft20 Nm
Ignition Switch3 specs
- Connector Bolts7 lb-ft9 Nm
- Steering Column Bolts22 lb-ft30 Nm
- Switch Mounting Screws4 lb-ft5 Nm
Spark Plugs9 specs
- Air Box Clips4 lb-ft5 Nm
- Connector Bolts7 lb-ft9 Nm
- Engine Cover Clips3 lb-ft4 Nm
- Ignition Coil Bolt6 lb-ft8 Nm
- Oil Drain PlugUse new crush washer26 lb-ft35 Nm
- Spark PlugGap before install15 lb-ft20 Nm
- Spark Plugs - Aluminum HeadApply anti-seize to threads15 lb-ft20 Nm
- Spark Plugs - Cast Iron HeadApply anti-seize to threads15 lb-ft20 Nm
- Wheel Lug NutsTorque in star pattern140 lb-ft190 Nm
Fuel system
Charcoal Canister5 specs
- Filter Bracket11 lb-ft15 Nm
- Fuel Line FittingsUse new O-rings18 lb-ft25 Nm
- Hose Clamps2 lb-ft3 Nm
- Pressure Regulator Screws7 lb-ft9 Nm
- Pump Mounting14 lb-ft19 Nm
EVAP Purge Valve4 specs
- Filter Bracket11 lb-ft15 Nm
- Hose Clamps2 lb-ft3 Nm
- Pressure Regulator Screws7 lb-ft9 Nm
- Pump Mounting14 lb-ft19 Nm
EVAP Vent Valve4 specs
- Filter Bracket11 lb-ft15 Nm
- Hose Clamps2 lb-ft3 Nm
- Pressure Regulator Screws7 lb-ft9 Nm
- Pump Mounting14 lb-ft19 Nm
Fuel Cap3 specs
- Filter Bracket11 lb-ft15 Nm
- Pressure Regulator Screws7 lb-ft9 Nm
- Pump Mounting14 lb-ft19 Nm
Fuel Filler Neck6 specs
- Filler Neck Bolts7 lb-ft10 Nm
- Filter Bracket11 lb-ft15 Nm
- Fuel Rail Bolts20 lb-ft27 Nm
- Hose Clamps2 lb-ft3 Nm
- Pressure Regulator Screws7 lb-ft9 Nm
- Pump Mounting14 lb-ft19 Nm
Fuel Filter7 specs
- Air Box Clips4 lb-ft5 Nm
- Connector Bolts7 lb-ft9 Nm
- Filter Bracket Bolt14 lb-ft18 Nm
- Fuel Filter Bracket Bolt7 lb-ft10 Nm
- Fuel Line FittingsIf threaded type18 lb-ft25 Nm
- Oil Drain PlugUse new crush washer26 lb-ft35 Nm
- Wheel Lug NutsTorque in star pattern140 lb-ft190 Nm
Fuel Filter - In-Tank6 specs
- Filter Bracket11 lb-ft15 Nm
- Filter Bracket Bolt14 lb-ft18 Nm
- Fuel Line FittingsUse new O-rings18 lb-ft25 Nm
- Hose Clamps2 lb-ft3 Nm
- Pressure Regulator Screws7 lb-ft9 Nm
- Pump Mounting14 lb-ft19 Nm
Fuel Injector - Single6 specs
- Filter Bracket11 lb-ft15 Nm
- Fuel Line FittingsUse new O-rings18 lb-ft25 Nm
- Fuel Rail Bolts9 lb-ft12 Nm
- Hose Clamps2 lb-ft3 Nm
- Pressure Regulator Screws7 lb-ft9 Nm
- Pump Mounting14 lb-ft19 Nm
Fuel Injector Cleaning6 specs
- Filter Bracket11 lb-ft15 Nm
- Fuel Line FittingsUse new O-rings18 lb-ft25 Nm
- Fuel Rail Bolts9 lb-ft12 Nm
- Hose Clamps2 lb-ft3 Nm
- Pressure Regulator Screws7 lb-ft9 Nm
- Pump Mounting14 lb-ft19 Nm
Fuel Injectors - All6 specs
- Filter Bracket11 lb-ft15 Nm
- Fuel Line FittingsUse new O-rings18 lb-ft25 Nm
- Fuel Rail Bolts9 lb-ft12 Nm
- Hose Clamps2 lb-ft3 Nm
- Pressure Regulator Screws7 lb-ft9 Nm
- Pump Mounting14 lb-ft19 Nm
Fuel Level Sensor5 specs
- Filter Bracket11 lb-ft15 Nm
- Fuel Line FittingsUse new O-rings18 lb-ft25 Nm
- Hose Clamps2 lb-ft3 Nm
- Pressure Regulator Screws7 lb-ft9 Nm
- Pump Mounting14 lb-ft19 Nm
Fuel Line - High Pressure6 specs
- Filter Bracket11 lb-ft15 Nm
- Fuel Line FittingsUse new O-rings18 lb-ft25 Nm
- Fuel Rail Bolts9 lb-ft12 Nm
- Hose Clamps2 lb-ft3 Nm
- Pressure Regulator Screws7 lb-ft9 Nm
- Pump Mounting14 lb-ft19 Nm
Fuel Line - Return6 specs
- Filter Bracket11 lb-ft15 Nm
- Fuel Line FittingsUse new O-rings18 lb-ft25 Nm
- Fuel Rail Bolts9 lb-ft12 Nm
- Hose Clamps2 lb-ft3 Nm
- Pressure Regulator Screws7 lb-ft9 Nm
- Pump Mounting14 lb-ft19 Nm
Fuel Pressure Regulator6 specs
- Filter Bracket11 lb-ft15 Nm
- Fuel Line18 lb-ft25 Nm
- Fuel Rail Bolts20 lb-ft27 Nm
- Pressure Regulator Screws7 lb-ft9 Nm
- Pump Mounting14 lb-ft19 Nm
- Regulator Mounting Screws4 lb-ft5 Nm
Fuel Pump2 specs
- Fuel Pump Module Lock RingUse special tool59 lb-ft80 Nm
- Tank Strap Bolts26 lb-ft35 Nm
Fuel Pump Module7 specs
- Access Cover Screws4 lb-ft5 Nm
- Filter Bracket11 lb-ft15 Nm
- Fuel Line FittingsUse new O-rings18 lb-ft25 Nm
- Fuel Pump Lock RingLock ring tool68 lb-ft92 Nm
- Hose Clamps2 lb-ft3 Nm
- Pressure Regulator Screws7 lb-ft9 Nm
- Pump Mounting14 lb-ft19 Nm
Fuel Rail6 specs
- Filter Bracket11 lb-ft15 Nm
- Fuel Line FittingsUse new O-rings18 lb-ft25 Nm
- Fuel Rail Bolts9 lb-ft12 Nm
- Hose Clamps2 lb-ft3 Nm
- Pressure Regulator Screws7 lb-ft9 Nm
- Pump Mounting14 lb-ft19 Nm
Fuel Tank7 specs
- Filler Neck Clamp3 lb-ft4 Nm
- Filter Bracket11 lb-ft15 Nm
- Fuel Line FittingsUse new O-rings18 lb-ft25 Nm
- Fuel Rail Bolts20 lb-ft27 Nm
- Pressure Regulator Screws7 lb-ft9 Nm
- Pump Mounting14 lb-ft19 Nm
- Tank Strap Bolts26 lb-ft35 Nm
Fuel Tank Strap5 specs
- Filter Bracket11 lb-ft15 Nm
- Fuel Line FittingsUse new O-rings18 lb-ft25 Nm
- Hose Clamps2 lb-ft3 Nm
- Pressure Regulator Screws7 lb-ft9 Nm
- Pump Mounting14 lb-ft19 Nm
High Pressure Fuel Pump5 specs
- Filter Bracket11 lb-ft15 Nm
- Fuel Line FittingsUse new O-rings18 lb-ft25 Nm
- Hose Clamps2 lb-ft3 Nm
- Pressure Regulator Screws7 lb-ft9 Nm
- Pump Mounting14 lb-ft19 Nm
Electrical
Airbag - Driver5 specs
- Airbag Module BoltsTorx - disconnect battery and wait 2 minutes5 lb-ft7 Nm
- Battery Terminal Bolts7 lb-ft9 Nm
- Connector Screws4 lb-ft5 Nm
- Ground Strap BoltsClean contact surfaces14 lb-ft19 Nm
- Steering Wheel Nut40 lb-ft54 Nm
Airbag - Passenger5 specs
- Airbag Module BoltsTorx - disconnect battery and wait 2 minutes5 lb-ft7 Nm
- Battery Terminal Bolts7 lb-ft9 Nm
- Connector Screws4 lb-ft5 Nm
- Dashboard Fasteners3 lb-ft4 Nm
- Ground Strap BoltsClean contact surfaces14 lb-ft19 Nm
Airbag - Side5 specs
- Battery Terminal Bolts7 lb-ft9 Nm
- Connector Screws4 lb-ft5 Nm
- Ground Strap BoltsClean contact surfaces14 lb-ft19 Nm
- Seat Mounting BoltsSafety critical45 lb-ft61 Nm
- Side Airbag Module BoltsTorx5 lb-ft7 Nm
Airbag Module/Computer4 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws4 lb-ft5 Nm
- Module Mounting Bolts6 lb-ft8 Nm
- Sensor Mounting Bolts7 lb-ft10 Nm
Alternator4 specs
- Alternator Mounting Bolts37 lb-ft50 Nm
- Alternator Pivot Bolt18 lb-ft25 Nm
- Battery Terminal BoltsDo not overtighten6 lb-ft8 Nm
- Serpentine Belt Tensioner41 lb-ft55 Nm
Alternator Belt4 specs
- Alternator Mounting Bolts47 lb-ft64 Nm
- Alternator Pivot Bolt47 lb-ft64 Nm
- Battery Cable Nut14 lb-ft18 Nm
- Connector Screws4 lb-ft5 Nm
Amplifier4 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws4 lb-ft5 Nm
- Ground Strap BoltsEnsure clean contact9 lb-ft12 Nm
- Module Mounting Bolts6 lb-ft8 Nm
Antenna2 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws4 lb-ft5 Nm
Backup Camera4 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws4 lb-ft5 Nm
- Module Mounting Bolts6 lb-ft8 Nm
- Sensor Mounting Bolts7 lb-ft10 Nm
Battery3 specs
- Battery Hold-Down Bolt6 lb-ft8 Nm
- Battery Terminal BoltsDo not overtighten - can crack terminal4 lb-ft6 Nm
- Battery Tray Bolts9 lb-ft12 Nm
Battery Cable - Negative6 specs
- Battery Hold-Down BoltDo not overtighten11 lb-ft15 Nm
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws4 lb-ft5 Nm
- Ground Cable Bolt14 lb-ft18 Nm
- Ground Strap BoltsEnsure clean contact9 lb-ft12 Nm
- Sensor Mounting Bolts7 lb-ft10 Nm
Battery Cable - Positive5 specs
- Battery Hold-Down BoltDo not overtighten11 lb-ft15 Nm
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws4 lb-ft5 Nm
- Ground Cable Bolt14 lb-ft18 Nm
- Module Mounting Bolts6 lb-ft8 Nm
Battery Cables - Both6 specs
- Battery Hold-Down BoltDo not overtighten11 lb-ft15 Nm
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws4 lb-ft5 Nm
- Ground Cable Bolt14 lb-ft18 Nm
- Ground Strap BoltsEnsure clean contact9 lb-ft12 Nm
- Sensor Mounting Bolts7 lb-ft10 Nm
Battery Terminal6 specs
- Battery Hold-Down BoltDo not overtighten11 lb-ft15 Nm
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws4 lb-ft5 Nm
- Ground Cable Bolt14 lb-ft18 Nm
- Ground Strap BoltsEnsure clean contact9 lb-ft12 Nm
- Sensor Mounting Bolts7 lb-ft10 Nm
Blower Motor2 specs
- Blower Motor Mounting Screw3 lb-ft4 Nm
- Blower Motor Resistor Screws1.5 lb-ft2 Nm
Blower Motor Control Module3 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws4 lb-ft5 Nm
- Module Mounting Bolts6 lb-ft8 Nm
Blower Motor Resistor4 specs
- Battery Terminal Bolts7 lb-ft9 Nm
- Connector Screws4 lb-ft5 Nm
- Ground Strap BoltsClean contact surfaces14 lb-ft19 Nm
- Resistor Screws1.5 lb-ft2 Nm
Clock Spring7 specs
- Airbag Module BoltsTorx - disconnect battery first5 lb-ft7 Nm
- Battery Terminal Bolts7 lb-ft9 Nm
- Clock Spring ScrewsAlign marks before removal3 lb-ft4 Nm
- Connector Screws4 lb-ft5 Nm
- Ground Strap BoltsClean contact surfaces14 lb-ft19 Nm
- Steering Column CoversPlastic clips2 lb-ft3 Nm
- Steering Wheel Nut40 lb-ft54 Nm
Combination Switch4 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws4 lb-ft5 Nm
- Module Mounting Bolts6 lb-ft8 Nm
- Sensor Mounting Bolts7 lb-ft10 Nm
Dimmer Switch3 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws4 lb-ft5 Nm
- Module Mounting Bolts6 lb-ft8 Nm
Door Lock Actuator - Front2 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws4 lb-ft5 Nm
Door Lock Actuator - Rear2 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws4 lb-ft5 Nm
Fog Light Assembly2 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws4 lb-ft5 Nm
Fog Light Bulb1 spec
- Connector Screws4 lb-ft5 Nm
Fuel Pump Relay6 specs
- Access Cover Screws4 lb-ft5 Nm
- Battery Terminal Bolts7 lb-ft9 Nm
- Connector Screws4 lb-ft5 Nm
- Fuel Pump Lock RingLock ring tool68 lb-ft92 Nm
- Ground Strap BoltsClean contact surfaces14 lb-ft19 Nm
- Relay Socket4 lb-ft5 Nm
Fuse Box - Engine Bay4 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws4 lb-ft5 Nm
- Ground Strap BoltsEnsure clean contact9 lb-ft12 Nm
- Module Mounting Bolts6 lb-ft8 Nm
Fuse Box - Interior4 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws4 lb-ft5 Nm
- Ground Strap BoltsEnsure clean contact9 lb-ft12 Nm
- Module Mounting Bolts6 lb-ft8 Nm
Headlight Assembly5 specs
- Adjuster Screws2 lb-ft3 Nm
- Battery Terminal Bolts7 lb-ft9 Nm
- Connector Screws4 lb-ft5 Nm
- Ground Strap BoltsClean contact surfaces14 lb-ft19 Nm
- Headlight Assembly Bolts7 lb-ft10 Nm
Headlight Bulb - Single4 specs
- Battery Terminal Bolts7 lb-ft9 Nm
- Bulb Retaining Ring4 lb-ft5 Nm
- Connector Screws4 lb-ft5 Nm
- Ground Strap BoltsClean contact surfaces14 lb-ft19 Nm
Headlight Bulbs - Pair1 spec
- Connector Screws4 lb-ft5 Nm
Headlight Switch3 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws4 lb-ft5 Nm
- Module Mounting Bolts6 lb-ft8 Nm
Heated Seat Module3 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws4 lb-ft5 Nm
- Module Mounting Bolts6 lb-ft8 Nm
HID Ballast3 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws4 lb-ft5 Nm
- Module Mounting Bolts6 lb-ft8 Nm
Horn4 specs
- Battery Terminal Bolts7 lb-ft9 Nm
- Connector Screws4 lb-ft5 Nm
- Ground Strap BoltsClean contact surfaces14 lb-ft19 Nm
- Horn Mounting Bolt11 lb-ft15 Nm
Horn Relay2 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws4 lb-ft5 Nm
Instrument Cluster3 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws4 lb-ft5 Nm
- Module Mounting Bolts6 lb-ft8 Nm
LED Headlight Module3 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws4 lb-ft5 Nm
- Module Mounting Bolts6 lb-ft8 Nm
Main Relay3 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws4 lb-ft5 Nm
- Module Mounting Bolts6 lb-ft8 Nm
Power Antenna Motor2 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws4 lb-ft5 Nm
Power Mirror Motor2 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws4 lb-ft5 Nm
Power Seat Motor3 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws4 lb-ft5 Nm
- Module Mounting Bolts6 lb-ft8 Nm
Power Window Motor - Front3 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws4 lb-ft5 Nm
- Module Mounting Bolts6 lb-ft8 Nm
Power Window Motor - Rear3 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws4 lb-ft5 Nm
- Module Mounting Bolts6 lb-ft8 Nm
Power Window Regulator - Front3 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws4 lb-ft5 Nm
- Module Mounting Bolts6 lb-ft8 Nm
Power Window Regulator - Rear2 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws4 lb-ft5 Nm
Radio/Head Unit3 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws4 lb-ft5 Nm
- Module Mounting Bolts6 lb-ft8 Nm
Relay - Generic3 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws4 lb-ft5 Nm
- Module Mounting Bolts6 lb-ft8 Nm
Seat Heater Element4 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws4 lb-ft5 Nm
- Module Mounting Bolts6 lb-ft8 Nm
- Sensor Mounting Bolts7 lb-ft10 Nm
Side Mirror Assembly2 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws4 lb-ft5 Nm
Speaker - Dash3 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws4 lb-ft5 Nm
- Sensor Mounting Bolts7 lb-ft10 Nm
Speaker - Door2 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws4 lb-ft5 Nm
Speedometer4 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws4 lb-ft5 Nm
- Module Mounting Bolts6 lb-ft8 Nm
- Sensor Mounting Bolts7 lb-ft10 Nm
Starter3 specs
- Heat Shield BoltsIf equipped7 lb-ft10 Nm
- Starter Mounting BoltLong bolt may need extension37 lb-ft50 Nm
- Starter Solenoid NutFor B+ cable9 lb-ft12 Nm
Starter Solenoid4 specs
- Battery Cable Nut14 lb-ft18 Nm
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws4 lb-ft5 Nm
- Starter Mounting Bolt47 lb-ft64 Nm
Subwoofer3 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws4 lb-ft5 Nm
- Module Mounting Bolts6 lb-ft8 Nm
Sunroof Motor3 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws4 lb-ft5 Nm
- Module Mounting Bolts6 lb-ft8 Nm
Sunroof Switch2 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws4 lb-ft5 Nm
Tail Light Assembly5 specs
- Battery Terminal Bolts7 lb-ft9 Nm
- Connector Screws4 lb-ft5 Nm
- Ground Strap BoltsClean contact surfaces14 lb-ft19 Nm
- Lens Screws1.5 lb-ft2 Nm
- Tail Light Bolts6 lb-ft8 Nm
Tail Light Bulb1 spec
- Connector Screws4 lb-ft5 Nm
Third Brake Light1 spec
- Connector Screws4 lb-ft5 Nm
Trunk/Liftgate Actuator2 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws4 lb-ft5 Nm
Turn Signal Bulb - Front1 spec
- Connector Screws4 lb-ft5 Nm
Turn Signal Bulb - Rear1 spec
- Connector Screws4 lb-ft5 Nm
Turn Signal Switch5 specs
- Battery Terminal Bolts7 lb-ft9 Nm
- Connector Screws4 lb-ft5 Nm
- Ground Strap BoltsClean contact surfaces14 lb-ft19 Nm
- Steering Column Covers1.5 lb-ft2 Nm
- Switch Mounting Screws2 lb-ft3 Nm
Voltage Regulator3 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws4 lb-ft5 Nm
- Module Mounting Bolts6 lb-ft8 Nm
Washer Pump2 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws4 lb-ft5 Nm
Washer Reservoir3 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws4 lb-ft5 Nm
- Sensor Mounting Bolts7 lb-ft10 Nm
Window Motor and Regulator - Front3 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws4 lb-ft5 Nm
- Module Mounting Bolts6 lb-ft8 Nm
Window Motor and Regulator - Rear3 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws4 lb-ft5 Nm
- Module Mounting Bolts6 lb-ft8 Nm
Wiper Linkage7 specs
- Battery Terminal Bolts7 lb-ft9 Nm
- Connector Screws4 lb-ft5 Nm
- Ground Strap BoltsEnsure clean contact9 lb-ft12 Nm
- Linkage Pivot Nuts9 lb-ft12 Nm
- Module Mounting Bolts6 lb-ft8 Nm
- Motor Mounting Bolts7 lb-ft10 Nm
- Sensor Mounting Bolts7 lb-ft10 Nm
Wiper Motor - Front3 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws4 lb-ft5 Nm
- Module Mounting Bolts6 lb-ft8 Nm
Wiper Motor - Rear2 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws4 lb-ft5 Nm
Wiper Switch2 specs
- Battery Terminal BoltsDo not overtighten4 lb-ft6 Nm
- Connector Screws4 lb-ft5 Nm
Suspension
Ball Joint - Lower7 specs
- Control Arm BoltsTorque with vehicle weight on wheels122 lb-ft165 Nm
- Lower Ball Joint Nut88 lb-ft119 Nm
- Pinch BoltNew bolt61 lb-ft82 Nm
- Strut Bolts115 lb-ft156 Nm
- Sway Bar Link61 lb-ft83 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug NutsTorque in star pattern140 lb-ft190 Nm
Ball Joint - Upper7 specs
- Control Arm BoltsTorque with vehicle weight on wheels122 lb-ft165 Nm
- Pinch BoltNew bolt61 lb-ft82 Nm
- Strut Bolts115 lb-ft156 Nm
- Sway Bar Link61 lb-ft83 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Upper Ball Joint Nut88 lb-ft119 Nm
- Wheel Lug NutsTorque in star pattern140 lb-ft190 Nm
Ball Joints - Upper and Lower9 specs
- Control Arm BoltsTorque with vehicle weight on wheels122 lb-ft165 Nm
- Lower Ball Joint NutUse new cotter pin88 lb-ft119 Nm
- Pinch BoltNew bolt61 lb-ft82 Nm
- Strut Bolts115 lb-ft156 Nm
- Strut Tower Nuts37 lb-ft50 Nm
- Sway Bar Link61 lb-ft83 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Upper Ball Joint NutUse new cotter pin87.8 lb-ft119 Nm
- Wheel Lug NutsTorque in star pattern140 lb-ft190 Nm
Coil Spring - Front6 specs
- Control Arm BoltsTorque with vehicle weight on wheels122 lb-ft165 Nm
- Strut Bolts115 lb-ft156 Nm
- Strut Tower Nuts37 lb-ft50 Nm
- Sway Bar Link61 lb-ft83 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug NutsTorque in star pattern140 lb-ft190 Nm
Coil Springs - Front Pair6 specs
- Control Arm BoltsTorque with vehicle weight on wheels122 lb-ft165 Nm
- Strut Bolts115 lb-ft156 Nm
- Strut Tower Nuts37 lb-ft50 Nm
- Sway Bar Link61 lb-ft83 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug NutsTorque in star pattern140 lb-ft190 Nm
Control Arm Bushing - Front Lower6 specs
- Control Arm BoltsTorque with vehicle weight on wheels122 lb-ft165 Nm
- Lower Ball Joint NutNew cotter pin88 lb-ft119 Nm
- Strut Bolts115 lb-ft156 Nm
- Sway Bar Link61 lb-ft83 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug Nuts140 lb-ft190 Nm
Control Arm Bushing - Front Upper6 specs
- Control Arm BoltsTorque with vehicle weight on wheels122 lb-ft165 Nm
- Strut Bolts115 lb-ft156 Nm
- Sway Bar Link61 lb-ft83 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Upper Ball Joint NutNew cotter pin88 lb-ft119 Nm
- Wheel Lug NutsTorque in star pattern140 lb-ft190 Nm
Front Struts - Pair7 specs
- Control Arm BoltsTorque with weight on wheels128 lb-ft174 Nm
- Strut Bolts115 lb-ft156 Nm
- Strut Tower Nuts47 lb-ft64 Nm
- Strut-to-Lower Control ArmSome models37 lb-ft50 Nm
- Sway Bar Link61 lb-ft83 Nm
- Upper Mount NutDo not overtighten30 lb-ft40 Nm
- Wheel Lug Nuts140 lb-ft190 Nm
Front Suspension Rebuild5 specs
- Ball Joint Pinch BoltUse new bolt if locknut style37 lb-ft50 Nm
- Lower Control Arm BoltsTorque at ride height81 lb-ft110 Nm
- Strut Top Mount Nuts18 lb-ft25 Nm
- Sway Bar End Link Nuts44 lb-ft60 Nm
- Upper Control Arm BoltsTorque at ride height66 lb-ft90 Nm
Knuckle/Spindle - Front8 specs
- Control Arm BoltsTorque with vehicle weight on wheels122 lb-ft165 Nm
- Lower Ball Joint NutUse new cotter pin88 lb-ft119 Nm
- Strut Bolts115 lb-ft156 Nm
- Strut Tower Nuts37 lb-ft50 Nm
- Sway Bar Link61 lb-ft83 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Upper Ball Joint Nut87.8 lb-ft119 Nm
- Wheel Lug Nuts140 lb-ft190 Nm
Lateral Arm5 specs
- Control Arm BoltsTorque with vehicle weight on wheels122 lb-ft165 Nm
- Strut Bolts115 lb-ft156 Nm
- Sway Bar Link61 lb-ft83 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug NutsTorque in star pattern140 lb-ft190 Nm
Leaf Spring4 specs
- Strut Bolts115 lb-ft156 Nm
- Sway Bar Link61 lb-ft83 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug Nuts140 lb-ft190 Nm
Leaf Spring Bushing4 specs
- Strut Bolts115 lb-ft156 Nm
- Sway Bar Link61 lb-ft83 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug Nuts140 lb-ft190 Nm
Leaf Spring Shackle3 specs
- Strut Bolts115 lb-ft156 Nm
- Sway Bar Link61 lb-ft83 Nm
- Wheel Lug Nuts140 lb-ft190 Nm
Leaf Spring U-Bolt Kit4 specs
- Strut Bolts115 lb-ft156 Nm
- Sway Bar Link61 lb-ft83 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug NutsTorque in star pattern140 lb-ft190 Nm
Lower Control Arm - Front7 specs
- Control Arm Bolts128 lb-ft174 Nm
- Control Arm-to-Frame BoltsTORQUE AT RIDE HEIGHT. Alignment cam bolts129 lb-ft175 Nm
- Lower Ball Joint NutTighten to align cotter pin hole74 lb-ft100 Nm
- Lower Control Arm Pivot BoltsTorque at ride height129 lb-ft175 Nm
- Strut Bolts115 lb-ft156 Nm
- Sway Bar Link61 lb-ft83 Nm
- Wheel Lug Nuts140 lb-ft190 Nm
Radius Arm5 specs
- Control Arm BoltsTorque with vehicle weight on wheels122 lb-ft165 Nm
- Strut Bolts115 lb-ft156 Nm
- Sway Bar Link61 lb-ft83 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug NutsTorque in star pattern140 lb-ft190 Nm
Radius Arm Bushing5 specs
- Control Arm BoltsTorque with vehicle weight on wheels122 lb-ft165 Nm
- Strut Bolts115 lb-ft156 Nm
- Sway Bar Link61 lb-ft83 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug NutsTorque in star pattern140 lb-ft190 Nm
Rear Shocks - Pair3 specs
- Sway Bar Link61 lb-ft83 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug NutsTorque in star pattern140 lb-ft190 Nm
Rear Suspension Service3 specs
- Shock Lower Bolt52 lb-ft70 Nm
- Sway Bar End Link Nuts37 lb-ft50 Nm
- Trailing Arm BoltsTorque at ride height88 lb-ft120 Nm
Shock Absorber Replacement2 specs
- Lower Mount Bolt66 lb-ft90 Nm
- Upper Mount NutUse new self-locking nut41 lb-ft55 Nm
Strut Assembly - Front3 specs
- Strut Mount Center NutHold strut shaft with Allen key41 lb-ft55 Nm
- Strut Tower NutsDo not loosen center nut unless compressed37 lb-ft50 Nm
- Sway Bar End Link Nuts41 lb-ft55 Nm
Strut Bearing6 specs
- Strut Bolts115 lb-ft156 Nm
- Strut to Knuckle Bolts122 lb-ft165 Nm
- Strut Tower Nuts37 lb-ft50 Nm
- Sway Bar Link61 lb-ft82 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug Nuts140 lb-ft190 Nm
Strut Mount - Front5 specs
- Strut Bolts115 lb-ft156 Nm
- Strut Tower Nuts37 lb-ft50 Nm
- Sway Bar Link61 lb-ft82 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug Nuts140 lb-ft190 Nm
Subframe6 specs
- Control Arm BoltsTorque with vehicle weight on wheels122 lb-ft165 Nm
- Strut Bolts115 lb-ft156 Nm
- Strut Tower Nuts37 lb-ft50 Nm
- Sway Bar Link61 lb-ft83 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug NutsTorque in star pattern140 lb-ft190 Nm
Subframe Bushing6 specs
- Control Arm BoltsTorque with vehicle weight on wheels122 lb-ft165 Nm
- Strut Bolts115 lb-ft156 Nm
- Strut Tower Nuts37 lb-ft50 Nm
- Sway Bar Link61 lb-ft83 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug NutsTorque in star pattern140 lb-ft190 Nm
Sway Bar - Front5 specs
- Strut Bolts115 lb-ft156 Nm
- Sway Bar Bracket Bolts47 lb-ft64 Nm
- Sway Bar Link61 lb-ft83 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug NutsTorque in star pattern140 lb-ft190 Nm
Sway Bar - Rear4 specs
- Sway Bar Bracket Bolts47 lb-ft64 Nm
- Sway Bar Link61 lb-ft83 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug NutsTorque in star pattern140 lb-ft190 Nm
Sway Bar Bushing - Front5 specs
- Strut Bolts115 lb-ft156 Nm
- Sway Bar Bracket Bolts47 lb-ft64 Nm
- Sway Bar Link61 lb-ft83 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug NutsTorque in star pattern140 lb-ft190 Nm
Sway Bar Bushing - Rear4 specs
- Sway Bar Bracket Bolts47 lb-ft64 Nm
- Sway Bar Link61 lb-ft83 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug NutsTorque in star pattern140 lb-ft190 Nm
Sway Bar Link - Front5 specs
- Strut Bolts115 lb-ft156 Nm
- Sway Bar Bracket Bolts47 lb-ft64 Nm
- Sway Bar Link61 lb-ft83 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug NutsTorque in star pattern140 lb-ft190 Nm
Sway Bar Link - Rear4 specs
- Sway Bar Bracket Bolts47 lb-ft64 Nm
- Sway Bar Link61 lb-ft83 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug NutsTorque in star pattern140 lb-ft190 Nm
Sway Bar Links - Front Pair5 specs
- Strut Bolts115 lb-ft156 Nm
- Sway Bar Bracket Bolts47 lb-ft64 Nm
- Sway Bar Link61 lb-ft83 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug NutsTorque in star pattern140 lb-ft190 Nm
Torsion Bar5 specs
- Control Arm BoltsTorque with vehicle weight on wheels122 lb-ft165 Nm
- Strut Bolts115 lb-ft156 Nm
- Sway Bar Link61 lb-ft83 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug Nuts140 lb-ft190 Nm
Torsion Bar Adjustment3 specs
- Strut Bolts115 lb-ft156 Nm
- Sway Bar Link61 lb-ft83 Nm
- Wheel Lug NutsTorque in star pattern140 lb-ft190 Nm
Trailing Arm5 specs
- Control Arm BoltsTorque with vehicle weight on wheels122 lb-ft165 Nm
- Strut Bolts115 lb-ft156 Nm
- Sway Bar Link61 lb-ft83 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug Nuts140 lb-ft190 Nm
Trailing Arm Bushing5 specs
- Control Arm BoltsTorque with vehicle weight on wheels122 lb-ft165 Nm
- Strut Bolts115 lb-ft156 Nm
- Sway Bar Link61 lb-ft83 Nm
- Sway Bar Link NutsHold shaft with Allen key41 lb-ft55 Nm
- Wheel Lug NutsTorque in star pattern140 lb-ft190 Nm
Upper Control Arm - Front6 specs
- Control Arm Bolts128 lb-ft174 Nm
- Control Arm-to-Frame NutsTORQUE AT RIDE HEIGHT (Weight on wheels) to prevent bushing failure90 lb-ft122 Nm
- Strut Bolts115 lb-ft156 Nm
- Sway Bar Link61 lb-ft83 Nm
- Upper Ball Joint NutTighten to 37 lb-ft then loosen 180°. Tighten to 37 lb-ft + 90-100 degrees (verify year)37 lb-ft + 90°50 Nm
- Wheel Lug Nuts140 lb-ft190 Nm
Steering
Center Link/Drag Link7 specs
- Castle NutsUse new cotter pins41 lb-ft55 Nm
- Coupling Bolt34 lb-ft46 Nm
- Power Steering Line FittingsUse new O-rings34 lb-ft46 Nm
- Steering Rack Bolts101 lb-ft137 Nm
- Tie Rod End NutUse new cotter pin54 lb-ft73 Nm
- Tie Rod Nut54 lb-ft73 Nm
- Wheel Lug Nuts140 lb-ft190 Nm
Idler Arm8 specs
- Coupling Bolt34 lb-ft46 Nm
- Idler Arm Bolts55 lb-ft75 Nm
- Power Steering Line FittingsUse new O-rings34 lb-ft46 Nm
- Steering Rack Bolts101 lb-ft137 Nm
- Tie Rod Castle Nut41 lb-ft55 Nm
- Tie Rod End NutUse new cotter pin54 lb-ft73 Nm
- Tie Rod Nut54 lb-ft73 Nm
- Wheel Lug Nuts140 lb-ft190 Nm
Pitman Arm7 specs
- Coupling Bolt34 lb-ft46 Nm
- Pitman Arm NutUse puller for removal136 lb-ft185 Nm
- Power Steering Line FittingsUse new O-rings34 lb-ft46 Nm
- Steering Rack Bolts101 lb-ft137 Nm
- Tie Rod End NutUse new cotter pin54 lb-ft73 Nm
- Tie Rod Nut54 lb-ft73 Nm
- Wheel Lug Nuts140 lb-ft190 Nm
Power Steering Fluid Flush7 specs
- Coupling Bolt34 lb-ft46 Nm
- Power Steering Line FittingsUse new O-rings22 lb-ft30 Nm
- Steering Rack Bolts74 lb-ft100 Nm
- Tie Rod End Castle NutUse new cotter pin41 lb-ft55 Nm
- Tie Rod End NutUse new cotter pin54 lb-ft73 Nm
- Tie Rod Nut54 lb-ft73 Nm
- Wheel Lug Nuts140 lb-ft190 Nm
Power Steering Gear Box9 specs
- Coupling Bolt34 lb-ft46 Nm
- Power Steering Line FittingsUse new O-rings. Verify sequence with the service manual22 lb-ft30 Nm
- Pressure Line FittingNew O-ring34 lb-ft46 Nm
- Pump Mounting Bolts27 lb-ft37 Nm
- Steering Rack BoltsVerify sequence with the service manual74 lb-ft100 Nm
- Tie Rod End Castle NutUse new cotter pin. Verify sequence with the service manual41 lb-ft55 Nm
- Tie Rod End NutUse new cotter pin54 lb-ft73 Nm
- Tie Rod Nut54 lb-ft73 Nm
- Wheel Lug Nuts140 lb-ft190 Nm
Power Steering Hose - High Pressure6 specs
- Coupling Bolt34 lb-ft46 Nm
- Power Steering Line FittingsUse new O-rings22 lb-ft30 Nm
- Steering Rack Bolts74 lb-ft100 Nm
- Tie Rod End NutUse new cotter pin54 lb-ft73 Nm
- Tie Rod Nut54 lb-ft73 Nm
- Wheel Lug Nuts140 lb-ft190 Nm
Power Steering Hose - Return6 specs
- Coupling Bolt34 lb-ft46 Nm
- Power Steering Line FittingsUse new O-rings22 lb-ft30 Nm
- Steering Rack Bolts74 lb-ft100 Nm
- Tie Rod End NutUse new cotter pin54 lb-ft73 Nm
- Tie Rod Nut54 lb-ft73 Nm
- Wheel Lug Nuts140 lb-ft190 Nm
Power Steering Pump8 specs
- High Pressure Hose FittingUse new O-rings18 lb-ft25 Nm
- Power Steering Pump Bolts18 lb-ft25 Nm
- Pressure Line FittingUse new O-rings22 lb-ft30 Nm
- Pulley NutHold pulley with pin spanner52 lb-ft70 Nm
- Pump Mounting Bolts18 lb-ft25 Nm
- Return Hose Clamp2 lb-ft3 Nm
- Return Line Clamp3 lb-ft4 Nm
- Serpentine Belt Tensioner41 lb-ft55 Nm
Power Steering Pump Pulley6 specs
- Coupling Bolt34 lb-ft46 Nm
- Pressure Line FittingNew O-ring34 lb-ft46 Nm
- Pump Mounting Bolts27 lb-ft37 Nm
- Tie Rod End NutUse new cotter pin54 lb-ft73 Nm
- Tie Rod Nut54 lb-ft73 Nm
- Wheel Lug Nuts140 lb-ft190 Nm
Power Steering Reservoir5 specs
- Coupling Bolt34 lb-ft46 Nm
- Power Steering Line FittingsUse new O-rings22 lb-ft30 Nm
- Tie Rod End NutUse new cotter pin54 lb-ft73 Nm
- Tie Rod Nut54 lb-ft73 Nm
- Wheel Lug Nuts140 lb-ft190 Nm
Rack and Pinion Boots5 specs
- Coupling Bolt34 lb-ft46 Nm
- Tie Rod End Castle NutUse new cotter pin41 lb-ft55 Nm
- Tie Rod End NutUse new cotter pin54 lb-ft73 Nm
- Tie Rod Nut54 lb-ft73 Nm
- Wheel Lug Nuts140 lb-ft190 Nm
Steering Angle Sensor4 specs
- Coupling Bolt34 lb-ft46 Nm
- Tie Rod End NutUse new cotter pin54 lb-ft73 Nm
- Tie Rod Nut54 lb-ft73 Nm
- Wheel Lug Nuts140 lb-ft190 Nm
Steering Column9 specs
- Coupling Bolt34 lb-ft46 Nm
- Ignition Switch BoltsVerify sequence with the service manual4 lb-ft5 Nm
- Pinch BoltVerify sequence with the service manual22 lb-ft30 Nm
- Power Steering Line FittingsUse new O-rings34 lb-ft46 Nm
- Steering Column BoltsVerify sequence with the service manual22 lb-ft30 Nm
- Steering Rack Bolts101 lb-ft137 Nm
- Tie Rod End NutUse new cotter pin54 lb-ft73 Nm
- Tie Rod Nut54 lb-ft73 Nm
- Wheel Lug Nuts140 lb-ft190 Nm
Steering Coupler5 specs
- Coupling Bolt34 lb-ft46 Nm
- Steering Rack BoltsVerify sequence with the service manual74 lb-ft100 Nm
- Tie Rod End NutUse new cotter pin54 lb-ft73 Nm
- Tie Rod Nut54 lb-ft73 Nm
- Wheel Lug Nuts140 lb-ft190 Nm
Steering Damper4 specs
- Coupling Bolt34 lb-ft46 Nm
- Tie Rod End NutUse new cotter pin54 lb-ft73 Nm
- Tie Rod Nut54 lb-ft73 Nm
- Wheel Lug Nuts140 lb-ft190 Nm
Steering Shaft - Intermediate5 specs
- Coupling Bolt34 lb-ft46 Nm
- Steering Rack BoltsVerify sequence with the service manual74 lb-ft100 Nm
- Tie Rod End NutUse new cotter pin54 lb-ft73 Nm
- Tie Rod Nut54 lb-ft73 Nm
- Wheel Lug Nuts140 lb-ft190 Nm
Steering Shaft - Upper4 specs
- Coupling Bolt34 lb-ft46 Nm
- Tie Rod End NutUse new cotter pin54 lb-ft73 Nm
- Tie Rod Nut54 lb-ft73 Nm
- Wheel Lug Nuts140 lb-ft190 Nm
Steering Wheel8 specs
- Airbag Module BoltsTorx - usually T30. Verify sequence with the service manual5 lb-ft7 Nm
- Coupling Bolt34 lb-ft46 Nm
- Power Steering Line FittingsUse new O-rings34 lb-ft46 Nm
- Steering Rack Bolts101 lb-ft137 Nm
- Steering Wheel NutVerify sequence with the service manual40 lb-ft54 Nm
- Tie Rod End NutUse new cotter pin54 lb-ft73 Nm
- Tie Rod Nut54 lb-ft73 Nm
- Wheel Lug Nuts140 lb-ft190 Nm
Tie Rod Assembly6 specs
- Coupling Bolt34 lb-ft46 Nm
- Tie Rod End Castle NutUse new cotter pin41 lb-ft55 Nm
- Tie Rod End NutNew cotter pin54 lb-ft73 Nm
- Tie Rod Lock NutAfter alignment68 lb-ft92 Nm
- Tie Rod Nut54 lb-ft73 Nm
- Wheel Lug Nuts140 lb-ft190 Nm
Tie Rod End - Inner7 specs
- Coupling Bolt34 lb-ft46 Nm
- Steering Rack Bolts74 lb-ft100 Nm
- Tie Rod End Castle NutUse new cotter pin41 lb-ft55 Nm
- Tie Rod End NutUse new cotter pin54 lb-ft73 Nm
- Tie Rod Lock NutAfter alignment68 lb-ft92 Nm
- Tie Rod Nut54 lb-ft73 Nm
- Wheel Lug Nuts140 lb-ft190 Nm
Tie Rod End - Outer5 specs
- Coupling Bolt34 lb-ft46 Nm
- Tie Rod End NutNew cotter pin54 lb-ft73 Nm
- Tie Rod Lock NutAfter alignment68 lb-ft92 Nm
- Tie Rod NutAlign cotter pin44 lb-ft60 Nm
- Wheel Lug Nuts140 lb-ft190 Nm
Tie Rods - Both Sides6 specs
- Coupling Bolt34 lb-ft46 Nm
- Tie Rod End Castle NutUse new cotter pin41 lb-ft55 Nm
- Tie Rod End NutUse new cotter pin54 lb-ft73 Nm
- Tie Rod Lock NutAfter alignment68 lb-ft92 Nm
- Tie Rod Nut54 lb-ft73 Nm
- Wheel Lug Nuts140 lb-ft190 Nm
Drivetrain
4WD Actuator5 specs
- CV Bolts61 lb-ft82 Nm
- CV Joint Bolts61 lb-ft83 Nm
- Differential Cover Bolts26 lb-ft35 Nm
- Driveshaft Bolts74 lb-ft100 Nm
- Wheel Lug NutsTorque in star pattern147 lb-ft200 Nm
Axle Seal - Front6 specs
- Axle NutUse new cotter pin or stake nut159 lb-ft216 Nm
- CV Bolts61 lb-ft82 Nm
- CV Joint Bolts61 lb-ft83 Nm
- Differential Cover Bolts26 lb-ft35 Nm
- Driveshaft Bolts74 lb-ft100 Nm
- Wheel Lug NutsTorque in star pattern140 lb-ft190 Nm
Axle Seal - Rear5 specs
- CV Bolts61 lb-ft82 Nm
- CV Joint Bolts61 lb-ft83 Nm
- Differential Cover Bolts26 lb-ft35 Nm
- Driveshaft Bolts74 lb-ft100 Nm
- Wheel Lug NutsTorque in star pattern140 lb-ft190 Nm
Axle Shaft - Rear5 specs
- CV Bolts61 lb-ft82 Nm
- CV Joint Bolts61 lb-ft83 Nm
- Differential Cover Bolts26 lb-ft35 Nm
- Driveshaft Bolts74 lb-ft100 Nm
- Wheel Lug NutsTorque in star pattern140 lb-ft190 Nm
CV Axle - Front9 specs
- Axle NutUse new nut, stake after159 lb-ft216 Nm
- Ball Joint Pinch Bolt41 lb-ft55 Nm
- CV Axle NutUse new cotter pin or stake nut159 lb-ft216 Nm
- CV Bolts61 lb-ft82 Nm
- CV Joint Bolts61 lb-ft83 Nm
- Differential Cover BoltsApply RTV sealant34 lb-ft46 Nm
- Driveshaft Bolts74 lb-ft100 Nm
- Lower Ball Joint Nut101 lb-ft137 Nm
- Wheel Lug Nuts140 lb-ft190 Nm
CV Axle - Rear5 specs
- CV Bolts61 lb-ft82 Nm
- CV Joint Bolts61 lb-ft83 Nm
- Differential Cover BoltsApply RTV sealant34 lb-ft46 Nm
- Driveshaft Bolts74 lb-ft100 Nm
- Wheel Lug Nuts140 lb-ft190 Nm
CV Axles - Front Pair6 specs
- Axle NutUse new cotter pin or stake nut159 lb-ft216 Nm
- CV Bolts61 lb-ft82 Nm
- CV Joint Bolts61 lb-ft83 Nm
- Driveshaft Bolts74 lb-ft100 Nm
- Lower Ball Joint Nut101 lb-ft137 Nm
- Wheel Lug NutsTorque in star pattern140 lb-ft190 Nm
CV Boot - Inner5 specs
- Axle NutUse new cotter pin or stake nut184 lb-ft250 Nm
- CV Bolts61 lb-ft82 Nm
- CV Joint Bolts61 lb-ft83 Nm
- Driveshaft Bolts74 lb-ft100 Nm
- Wheel Lug NutsTorque in star pattern140 lb-ft190 Nm
CV Boot - Outer5 specs
- Axle NutUse new cotter pin or stake nut184 lb-ft250 Nm
- CV Bolts61 lb-ft82 Nm
- CV Joint Bolts61 lb-ft83 Nm
- Driveshaft Bolts74 lb-ft100 Nm
- Wheel Lug NutsTorque in star pattern140 lb-ft190 Nm
Differential Cover Gasket4 specs
- CV Bolts61 lb-ft82 Nm
- CV Joint Bolts61 lb-ft83 Nm
- Differential Cover Bolts26 lb-ft35 Nm
- Driveshaft Bolts74 lb-ft100 Nm
Differential Fluid Change - Front5 specs
- Axle NutUse new cotter pin or stake nut159 lb-ft216 Nm
- CV Bolts61 lb-ft82 Nm
- CV Joint Bolts61 lb-ft83 Nm
- Differential Cover Bolts26 lb-ft35 Nm
- Driveshaft Bolts74 lb-ft100 Nm
Differential Fluid Change - Rear4 specs
- CV Bolts61 lb-ft82 Nm
- CV Joint Bolts61 lb-ft83 Nm
- Differential Cover Bolts26 lb-ft35 Nm
- Driveshaft Bolts74 lb-ft100 Nm
Differential Pinion Seal5 specs
- CV Bolts61 lb-ft82 Nm
- CV Joint Bolts61 lb-ft83 Nm
- Differential Cover Bolts26 lb-ft35 Nm
- Driveshaft Bolts74 lb-ft100 Nm
- Driveshaft U-Joint StrapsTighten evenly15 lb-ft20 Nm
Differential Rebuild - Front9 specs
- Axle NutUse new cotter pin or stake nut159 lb-ft216 Nm
- CV Bolts61 lb-ft82 Nm
- CV Joint Bolts61 lb-ft83 Nm
- Differential Cover Bolts26 lb-ft35 Nm
- Drain PlugNew washer41 lb-ft55 Nm
- Driveshaft Bolts74 lb-ft100 Nm
- Driveshaft U-Joint StrapsTighten evenly15 lb-ft20 Nm
- Fill Plug41 lb-ft55 Nm
- Wheel Lug NutsTorque in star pattern140 lb-ft190 Nm
Differential Rebuild - Rear8 specs
- CV Bolts61 lb-ft82 Nm
- CV Joint Bolts61 lb-ft83 Nm
- Differential Cover Bolts26 lb-ft35 Nm
- Drain PlugNew washer41 lb-ft55 Nm
- Driveshaft Bolts74 lb-ft100 Nm
- Driveshaft U-Joint StrapsTighten evenly15 lb-ft20 Nm
- Fill Plug41 lb-ft55 Nm
- Wheel Lug NutsTorque in star pattern140 lb-ft190 Nm
Driveshaft - Front3 specs
- Center Support Bearing Bracket Bolts37 lb-ft50 Nm
- Driveshaft Flange Bolts (CV/U-Joint)Use new bolts if torque-to-yield55 lb-ft75 Nm
- Transfer Case Output Yoke NutIf accessible133 lb-ft180 Nm
Driveshaft - Rear3 specs
- Differential Pinion Yoke NutUse new nut, set pinion preload184 lb-ft250 Nm
- Driveshaft Flange Bolts55 lb-ft75 Nm
- U-Joint Strap BoltsApply threadlocker26 lb-ft35 Nm
Driveshaft Center Support Bearing2 specs
- Center Support Bearing Bracket Bolts37 lb-ft50 Nm
- Driveshaft Flange Bolts55 lb-ft75 Nm
Front Differential7 specs
- Axle NutUse new cotter pin or stake nut159 lb-ft216 Nm
- CV Bolts61 lb-ft82 Nm
- CV Joint Bolts61 lb-ft83 Nm
- Differential Cover Bolts26 lb-ft35 Nm
- Driveshaft Bolts74 lb-ft100 Nm
- Driveshaft U-Joint StrapsTighten evenly15 lb-ft20 Nm
- Wheel Lug NutsTorque in star pattern140 lb-ft190 Nm
Limited Slip Clutch Pack7 specs
- Axle NutUse new cotter pin or stake nut184 lb-ft250 Nm
- CV Bolts61 lb-ft82 Nm
- CV Joint Bolts61 lb-ft83 Nm
- Differential Cover Bolts26 lb-ft35 Nm
- Driveshaft Bolts74 lb-ft100 Nm
- Driveshaft U-Joint StrapsTighten evenly15 lb-ft20 Nm
- Wheel Lug NutsTorque in star pattern140 lb-ft190 Nm
Locking Hub - Auto5 specs
- Axle NutUse new cotter pin or stake nut184 lb-ft250 Nm
- CV Bolts61 lb-ft82 Nm
- CV Joint Bolts61 lb-ft83 Nm
- Driveshaft Bolts74 lb-ft100 Nm
- Wheel Lug NutsTorque in star pattern140 lb-ft190 Nm
Rear Differential6 specs
- CV Bolts61 lb-ft82 Nm
- CV Joint Bolts61 lb-ft83 Nm
- Differential Cover Bolts26 lb-ft35 Nm
- Driveshaft Bolts74 lb-ft100 Nm
- Driveshaft U-Joint StrapsTighten evenly15 lb-ft20 Nm
- Wheel Lug NutsTorque in star pattern140 lb-ft190 Nm
Ring and Pinion7 specs
- Axle NutUse new cotter pin or stake nut184 lb-ft250 Nm
- CV Bolts61 lb-ft82 Nm
- CV Joint Bolts61 lb-ft83 Nm
- Differential Cover Bolts26 lb-ft35 Nm
- Driveshaft Bolts74 lb-ft100 Nm
- Driveshaft U-Joint StrapsTighten evenly15 lb-ft20 Nm
- Wheel Lug NutsTorque in star pattern140 lb-ft190 Nm
Transfer Case8 specs
- Axle NutUse new nut, stake after243 lb-ft329 Nm
- CV Bolts61 lb-ft82 Nm
- CV Joint Bolts61 lb-ft83 Nm
- Differential Cover BoltsApply RTV sealant34 lb-ft46 Nm
- Driveshaft Bolts74 lb-ft100 Nm
- Driveshaft Flange Bolts15 lb-ft20 Nm
- Transfer Case Bolts26 lb-ft35 Nm
- Wheel Lug Nuts140 lb-ft190 Nm
Transfer Case Chain4 specs
- CV Bolts61 lb-ft82 Nm
- CV Joint Bolts61 lb-ft83 Nm
- Driveshaft Bolts74 lb-ft100 Nm
- Driveshaft U-Joint StrapsTighten evenly15 lb-ft20 Nm
Transfer Case Encoder Motor3 specs
- CV Bolts61 lb-ft82 Nm
- CV Joint Bolts61 lb-ft83 Nm
- Driveshaft Bolts74 lb-ft100 Nm
Transfer Case Fluid Change6 specs
- Air Box Clips4 lb-ft5 Nm
- Connector Bolts7 lb-ft9 Nm
- Oil Drain PlugUse new crush washer26 lb-ft35 Nm
- Transfer Case Drain Plug18 lb-ft25 Nm
- Transfer Case Fill Plug18 lb-ft25 Nm
- Wheel Lug NutsTorque in star pattern140 lb-ft190 Nm
Transfer Case Motor/Actuator3 specs
- CV Bolts61 lb-ft82 Nm
- CV Joint Bolts61 lb-ft83 Nm
- Driveshaft Bolts74 lb-ft100 Nm
U-Joint8 specs
- Axle NutUse new nut, stake after243 lb-ft329 Nm
- CV Bolts61 lb-ft82 Nm
- CV Joint Bolts61 lb-ft83 Nm
- Differential Cover BoltsApply RTV sealant34 lb-ft46 Nm
- Driveshaft Bolts74 lb-ft100 Nm
- Driveshaft U-Joint StrapsTighten evenly15 lb-ft20 Nm
- Wheel Lug Nuts140 lb-ft190 Nm
- Yoke NutIf equipped111 lb-ft150 Nm
Wheel Bearing - Press-In Front6 specs
- ABS Sensor Bolt11 lb-ft15 Nm
- Axle NutUse new cotter pin or stake nut159 lb-ft216 Nm
- CV Joint Bolts61 lb-ft83 Nm
- Driveshaft Bolts74 lb-ft100 Nm
- Hub Bolts101 lb-ft137 Nm
- Wheel Lug NutsTorque in star pattern140 lb-ft190 Nm
Wheel Bearing - Press-In Rear6 specs
- ABS Sensor Bolt11 lb-ft15 Nm
- CV Joint Bolts61 lb-ft83 Nm
- Differential Cover Bolts26 lb-ft35 Nm
- Driveshaft Bolts74 lb-ft100 Nm
- Hub Bolts101 lb-ft137 Nm
- Wheel Lug NutsTorque in star pattern140 lb-ft190 Nm
Wheel Bearing Hub - Front4 specs
- ABS Sensor BoltDo not overtighten7 lb-ft10 Nm
- Axle NutUse new cotter pin after torque184 lb-ft250 Nm
- Caliper Bracket Bolts88 lb-ft120 Nm
- Wheel Bearing Hub BoltsApply threadlocker if specified81 lb-ft110 Nm
Wheel Bearing Hub - Rear2 specs
- Caliper Bracket Bolts81 lb-ft110 Nm
- Wheel Bearing Hub BoltsApply threadlocker if specified74 lb-ft100 Nm
Wheel Studs5 specs
- Axle NutUse new cotter pin or stake nut184 lb-ft250 Nm
- CV Bolts61 lb-ft82 Nm
- CV Joint Bolts61 lb-ft83 Nm
- Driveshaft Bolts74 lb-ft100 Nm
- Wheel Lug NutsTorque in star pattern140 lb-ft190 Nm
Transmission
Clutch Hydraulic Line4 specs
- Bell Housing Bolts47 lb-ft64 Nm
- Drain PlugUse new washer34 lb-ft46 Nm
- Fill Plug34 lb-ft46 Nm
- Pressure Plate BoltStar pattern27 lb-ft37 Nm
Dual Mass Flywheel4 specs
- Drain PlugUse new washer34 lb-ft46 Nm
- Fill Plug34 lb-ft46 Nm
- Flywheel BoltsOften TTY, tighten in star pattern70 lb-ft95 Nm
- Transmission Drain PlugUse new crush washer if equipped22 lb-ft30 Nm
Manual Trans Fluid Change3 specs
- Drain PlugUse new washer34 lb-ft46 Nm
- Fill Plug34 lb-ft46 Nm
- Transmission Drain PlugUse new crush washer if equipped22 lb-ft30 Nm
Neutral Safety Switch3 specs
- Drain PlugUse new washer34 lb-ft46 Nm
- Fill Plug34 lb-ft46 Nm
- Switch Mounting Bolts11 lb-ft15 Nm
Overdrive Solenoid4 specs
- Drain PlugUse new washer34 lb-ft46 Nm
- Fill Plug34 lb-ft46 Nm
- Transmission Drain PlugUse new crush washer if equipped22 lb-ft30 Nm
- Transmission Pan BoltsTighten in criss-cross pattern9 lb-ft12 Nm
Pressure Plate4 specs
- Drain PlugUse new washer34 lb-ft46 Nm
- Fill Plug34 lb-ft46 Nm
- Flywheel BoltsOften TTY, tighten in star pattern70 lb-ft95 Nm
- Transmission Drain PlugUse new crush washer if equipped22 lb-ft30 Nm
Shift Cable4 specs
- Adjustment Nut7 lb-ft10 Nm
- Cable Bracket Bolts11 lb-ft15 Nm
- Drain PlugUse new washer34 lb-ft46 Nm
- Fill Plug34 lb-ft46 Nm
Shift Fork3 specs
- Drain PlugUse new washer34 lb-ft46 Nm
- Fill Plug34 lb-ft46 Nm
- Transmission Drain PlugUse new crush washer if equipped22 lb-ft30 Nm
Shift Linkage4 specs
- Drain PlugUse new washer34 lb-ft46 Nm
- Fill Plug34 lb-ft46 Nm
- Linkage Bolts11 lb-ft15 Nm
- Pivot Bolts9 lb-ft12 Nm
Shift Solenoid - Single4 specs
- Drain PlugUse new washer34 lb-ft46 Nm
- Fill Plug34 lb-ft46 Nm
- Transmission Drain PlugUse new crush washer if equipped22 lb-ft30 Nm
- Transmission Pan BoltsTighten in criss-cross pattern9 lb-ft12 Nm
Shift Solenoids - All4 specs
- Drain PlugUse new washer34 lb-ft46 Nm
- Fill Plug34 lb-ft46 Nm
- Transmission Drain PlugUse new crush washer if equipped22 lb-ft30 Nm
- Transmission Pan BoltsTighten in criss-cross pattern9 lb-ft12 Nm
Synchros - All4 specs
- Drain PlugUse new washer34 lb-ft46 Nm
- Fill Plug34 lb-ft46 Nm
- Transmission Drain PlugUse new crush washer if equipped22 lb-ft30 Nm
- Transmission Pan BoltsTighten in criss-cross pattern9 lb-ft12 Nm
Synchros - Single Gear3 specs
- Drain PlugUse new washer34 lb-ft46 Nm
- Fill Plug34 lb-ft46 Nm
- Transmission Drain PlugUse new crush washer if equipped22 lb-ft30 Nm
Torque Converter4 specs
- Drain PlugUse new washer34 lb-ft46 Nm
- Fill Plug34 lb-ft46 Nm
- Flexplate BoltsAutomatic transmissions63 lb-ft85 Nm
- Torque Converter BoltsTighten evenly37 lb-ft50 Nm
Torque Converter Clutch Solenoid4 specs
- Drain PlugUse new washer34 lb-ft46 Nm
- Fill Plug34 lb-ft46 Nm
- Transmission Drain PlugUse new crush washer if equipped22 lb-ft30 Nm
- Transmission Pan BoltsTighten in criss-cross pattern9 lb-ft12 Nm
Transmission Control Module4 specs
- Drain PlugUse new washer34 lb-ft46 Nm
- Fill Plug34 lb-ft46 Nm
- Transmission Drain PlugUse new crush washer if equipped22 lb-ft30 Nm
- Transmission Pan BoltsTighten in criss-cross pattern9 lb-ft12 Nm
Transmission Cooler Lines2 specs
- Drain PlugUse new washer34 lb-ft46 Nm
- Fill Plug34 lb-ft46 Nm
Transmission Filter4 specs
- Drain PlugUse new washer34 lb-ft46 Nm
- Fill Plug34 lb-ft46 Nm
- Transmission Drain PlugUse new crush washer if equipped22 lb-ft30 Nm
- Transmission Pan BoltsTighten in criss-cross pattern9 lb-ft12 Nm
Transmission Filter and Fluid4 specs
- Drain PlugUse new washer34 lb-ft46 Nm
- Fill Plug34 lb-ft46 Nm
- Transmission Drain PlugUse new crush washer if equipped22 lb-ft30 Nm
- Transmission Pan BoltsTighten in criss-cross pattern9 lb-ft12 Nm
Transmission Fluid Change5 specs
- Drain PlugUse new washer34 lb-ft46 Nm
- Fill Plug34 lb-ft46 Nm
- Transmission Drain PlugUse new crush washer if equipped22 lb-ft30 Nm
- Transmission Filter BoltsIf equipped with bolted filter6 lb-ft8 Nm
- Transmission Pan BoltsTighten in criss-cross pattern9 lb-ft12 Nm
Transmission Flush4 specs
- Drain PlugUse new washer34 lb-ft46 Nm
- Fill Plug34 lb-ft46 Nm
- Transmission Drain PlugUse new crush washer if equipped22 lb-ft30 Nm
- Transmission Pan BoltsTighten in criss-cross pattern9 lb-ft12 Nm
Transmission Input Shaft Bearing5 specs
- Drain PlugUse new washer34 lb-ft46 Nm
- Fill Plug34 lb-ft46 Nm
- Flywheel BoltsOften TTY, tighten in star pattern70 lb-ft95 Nm
- Transmission Drain PlugUse new crush washer if equipped22 lb-ft30 Nm
- Transmission Pan BoltsTighten in criss-cross pattern9 lb-ft12 Nm
Transmission Oil Cooler9 specs
- Coolant Drain Plug11 lb-ft15 Nm
- Drain PetcockHand tight7 lb-ft9 Nm
- Drain PlugUse new washer34 lb-ft46 Nm
- Fan Bolts11 lb-ft15 Nm
- Fill Plug34 lb-ft46 Nm
- Hose Clamps2 lb-ft3 Nm
- Pump BoltsTorque in sequence24 lb-ft33 Nm
- Thermostat Housing Bolt11 lb-ft15 Nm
- Water Pump BoltsTighten in criss-cross pattern18 lb-ft25 Nm
Transmission Output Shaft Bearing5 specs
- Drain PlugUse new washer34 lb-ft46 Nm
- Fill Plug34 lb-ft46 Nm
- Flywheel BoltsOften TTY, tighten in star pattern70 lb-ft95 Nm
- Transmission Drain PlugUse new crush washer if equipped22 lb-ft30 Nm
- Transmission Pan BoltsTighten in criss-cross pattern9 lb-ft12 Nm
Transmission Pan Gasket4 specs
- Drain PlugUse new washer34 lb-ft46 Nm
- Fill Plug34 lb-ft46 Nm
- Transmission Drain PlugUse new crush washer if equipped22 lb-ft30 Nm
- Transmission Pan BoltsTighten in criss-cross pattern9 lb-ft12 Nm
Transmission R&R - Automatic5 specs
- Drain PlugUse new washer34 lb-ft46 Nm
- Fill Plug34 lb-ft46 Nm
- Flywheel BoltsOften TTY, tighten in star pattern70 lb-ft95 Nm
- Transmission Drain PlugUse new crush washer if equipped22 lb-ft30 Nm
- Transmission Pan BoltsTighten in criss-cross pattern9 lb-ft12 Nm
Transmission R&R - Manual4 specs
- Drain PlugUse new washer34 lb-ft46 Nm
- Fill Plug34 lb-ft46 Nm
- Flywheel BoltsOften TTY, tighten in star pattern70 lb-ft95 Nm
- Transmission Drain PlugUse new crush washer if equipped22 lb-ft30 Nm
Transmission Range Sensor4 specs
- Drain PlugUse new washer34 lb-ft46 Nm
- Fill Plug34 lb-ft46 Nm
- Transmission Drain PlugUse new crush washer if equipped22 lb-ft30 Nm
- Transmission Pan BoltsTighten in criss-cross pattern9 lb-ft12 Nm
Transmission Rebuild - Automatic5 specs
- Drain PlugUse new washer34 lb-ft46 Nm
- Fill Plug34 lb-ft46 Nm
- Flywheel BoltsOften TTY, tighten in star pattern70 lb-ft95 Nm
- Transmission Drain PlugUse new crush washer if equipped22 lb-ft30 Nm
- Transmission Pan BoltsTighten in criss-cross pattern9 lb-ft12 Nm
Transmission Rebuild - Manual5 specs
- Drain PlugUse new washer34 lb-ft46 Nm
- Fill Plug34 lb-ft46 Nm
- Flywheel BoltsOften TTY, tighten in star pattern70 lb-ft95 Nm
- Transmission Drain PlugUse new crush washer if equipped22 lb-ft30 Nm
- Transmission Pan BoltsTighten in criss-cross pattern9 lb-ft12 Nm
Transmission Speed Sensor - Input3 specs
- Drain PlugUse new washer34 lb-ft46 Nm
- Fill Plug34 lb-ft46 Nm
- Transmission Pan BoltsTighten in criss-cross pattern9 lb-ft12 Nm
Transmission Speed Sensor - Output2 specs
- Drain PlugUse new washer34 lb-ft46 Nm
- Fill Plug34 lb-ft46 Nm
Valve Body4 specs
- Drain PlugUse new washer34 lb-ft46 Nm
- Fill Plug34 lb-ft46 Nm
- Transmission Drain PlugUse new crush washer if equipped22 lb-ft30 Nm
- Transmission Pan BoltsTighten in criss-cross pattern9 lb-ft12 Nm
Exhaust
Catalytic Converter - Direct Fit5 specs
- Exhaust Flange BoltApply anti-seize33 lb-ft45 Nm
- Hanger Bolts20 lb-ft27 Nm
- Heat Shield Bolts7 lb-ft10 Nm
- Manifold NutsApply anti-seize34 lb-ft46 Nm
- O2 SensorApply anti-seize to threads only33 lb-ft45 Nm
Catalytic Converter - Universal5 specs
- Exhaust Flange BoltApply anti-seize33 lb-ft45 Nm
- Hanger Bolts20 lb-ft27 Nm
- Heat Shield Bolts7 lb-ft10 Nm
- Manifold NutsApply anti-seize34 lb-ft46 Nm
- O2 SensorApply anti-seize to threads only33 lb-ft45 Nm
Downpipe5 specs
- Exhaust Flange BoltApply anti-seize33 lb-ft45 Nm
- Hanger Bolts20 lb-ft27 Nm
- Heat Shield Bolts7 lb-ft10 Nm
- Manifold NutsApply anti-seize34 lb-ft46 Nm
- O2 SensorApply anti-seize to threads only33 lb-ft45 Nm
EGR Cooler5 specs
- Exhaust Flange BoltApply anti-seize33 lb-ft45 Nm
- Hanger Bolts20 lb-ft27 Nm
- Heat Shield Bolts7 lb-ft10 Nm
- Manifold NutsApply anti-seize34 lb-ft46 Nm
- O2 SensorApply anti-seize to threads only33 lb-ft45 Nm
EGR Tube4 specs
- Exhaust Flange BoltApply anti-seize33 lb-ft45 Nm
- Hanger Bolts20 lb-ft27 Nm
- Heat Shield Bolts7 lb-ft10 Nm
- Manifold NutsApply anti-seize34 lb-ft46 Nm
EGR Valve6 specs
- EGR Tube Fitting26 lb-ft35 Nm
- EGR Valve Bolts18 lb-ft25 Nm
- Hanger Bolts20 lb-ft27 Nm
- Heat Shield Bolts14 lb-ft19 Nm
- Manifold NutsApply anti-seize34 lb-ft46 Nm
- O2 SensorApply anti-seize to threads47 lb-ft64 Nm
Exhaust Clamp4 specs
- Exhaust Flange BoltApply anti-seize33 lb-ft45 Nm
- Hanger Bolts20 lb-ft27 Nm
- Heat Shield Bolts7 lb-ft10 Nm
- Manifold NutsApply anti-seize34 lb-ft46 Nm
Exhaust Gasket - Front5 specs
- Exhaust Flange BoltApply anti-seize33 lb-ft45 Nm
- Hanger Bolts20 lb-ft27 Nm
- Heat Shield Bolts7 lb-ft10 Nm
- Manifold NutsApply anti-seize34 lb-ft46 Nm
- O2 SensorApply anti-seize to threads only33 lb-ft45 Nm
Exhaust Gasket - Rear4 specs
- Exhaust Flange BoltApply anti-seize33 lb-ft45 Nm
- Hanger Bolts20 lb-ft27 Nm
- Heat Shield Bolts7 lb-ft10 Nm
- Manifold NutsApply anti-seize34 lb-ft46 Nm
Exhaust Hangers4 specs
- Exhaust Flange BoltApply anti-seize33 lb-ft45 Nm
- Hanger Bolts20 lb-ft27 Nm
- Heat Shield Bolts7 lb-ft10 Nm
- Manifold NutsApply anti-seize34 lb-ft46 Nm
Exhaust Manifold Studs5 specs
- Exhaust Flange BoltApply anti-seize33 lb-ft45 Nm
- Hanger Bolts20 lb-ft27 Nm
- Heat Shield Bolts7 lb-ft10 Nm
- Manifold NutsApply anti-seize34 lb-ft46 Nm
- O2 SensorApply anti-seize to threads only33 lb-ft45 Nm
Exhaust Pipe - Rear Section4 specs
- Exhaust Flange BoltApply anti-seize33 lb-ft45 Nm
- Hanger Bolts20 lb-ft27 Nm
- Heat Shield Bolts7 lb-ft10 Nm
- Manifold NutsApply anti-seize34 lb-ft46 Nm
Exhaust Tip3 specs
- Exhaust Flange BoltApply anti-seize33 lb-ft45 Nm
- Hanger Bolts20 lb-ft27 Nm
- Manifold NutsApply anti-seize34 lb-ft46 Nm
Flex Pipe5 specs
- Exhaust Clamps41 lb-ft55 Nm
- Hanger Bolts20 lb-ft27 Nm
- Heat Shield Bolts14 lb-ft19 Nm
- Manifold NutsApply anti-seize34 lb-ft46 Nm
- O2 Sensor47 lb-ft64 Nm
Front Pipe5 specs
- Exhaust Flange BoltApply anti-seize33 lb-ft45 Nm
- Hanger Bolts20 lb-ft27 Nm
- Heat Shield Bolts7 lb-ft10 Nm
- Manifold NutsApply anti-seize34 lb-ft46 Nm
- O2 SensorApply anti-seize to threads only33 lb-ft45 Nm
Intermediate Pipe5 specs
- Exhaust Flange BoltApply anti-seize33 lb-ft45 Nm
- Hanger Bolts20 lb-ft27 Nm
- Heat Shield Bolts7 lb-ft10 Nm
- Manifold NutsApply anti-seize34 lb-ft46 Nm
- O2 SensorApply anti-seize to threads only33 lb-ft45 Nm
Muffler2 specs
- Hanger Bracket Bolts18 lb-ft25 Nm
- Muffler Clamps41 lb-ft55 Nm
O2 Sensor - Downstream5 specs
- Exhaust Flange BoltApply anti-seize33 lb-ft45 Nm
- Hanger Bolts20 lb-ft27 Nm
- Heat Shield Bolts7 lb-ft10 Nm
- Manifold NutsApply anti-seize34 lb-ft46 Nm
- O2 SensorApply anti-seize to threads only33 lb-ft45 Nm
O2 Sensor - Upstream5 specs
- Exhaust Flange BoltApply anti-seize33 lb-ft45 Nm
- Hanger Bolts20 lb-ft27 Nm
- Heat Shield Bolts7 lb-ft10 Nm
- Manifold NutsApply anti-seize34 lb-ft46 Nm
- O2 SensorApply anti-seize to threads only33 lb-ft45 Nm
O2 Sensors - All5 specs
- Exhaust Flange BoltApply anti-seize33 lb-ft45 Nm
- Hanger Bolts20 lb-ft27 Nm
- Heat Shield Bolts7 lb-ft10 Nm
- Manifold NutsApply anti-seize34 lb-ft46 Nm
- O2 SensorApply anti-seize to threads only33 lb-ft45 Nm
Resonator5 specs
- Exhaust Clamps41 lb-ft55 Nm
- Hanger Bolts20 lb-ft27 Nm
- Heat Shield Bolts14 lb-ft19 Nm
- Manifold NutsApply anti-seize34 lb-ft46 Nm
- O2 Sensor47 lb-ft64 Nm
Tail Pipe4 specs
- Exhaust Flange BoltApply anti-seize33 lb-ft45 Nm
- Hanger Bolts20 lb-ft27 Nm
- Heat Shield Bolts7 lb-ft10 Nm
- Manifold NutsApply anti-seize34 lb-ft46 Nm
Heating and A/C
AC Accumulator5 specs
- AC Line FittingsUse new O-rings, add PAG oil15 lb-ft20 Nm
- Blower Motor Mounting Screw3 lb-ft4 Nm
- Compressor Bolts34 lb-ft46 Nm
- Duct Clips3 lb-ft4 Nm
- Mounting Bracket Bolts24 lb-ft33 Nm
AC Clutch Coil4 specs
- Blower Motor Mounting Screw3 lb-ft4 Nm
- Compressor Bolts34 lb-ft46 Nm
- Duct Clips3 lb-ft4 Nm
- Mounting Bracket Bolts24 lb-ft33 Nm
AC Compressor3 specs
- AC Compressor Bolts37 lb-ft50 Nm
- AC Line FittingsUse new O-rings, add PAG oil15 lb-ft20 Nm
- Clutch Connector Bolt6 lb-ft8 Nm
AC Compressor Clutch4 specs
- Blower Motor Mounting Screw3 lb-ft4 Nm
- Compressor Bolts34 lb-ft46 Nm
- Duct Clips3 lb-ft4 Nm
- Mounting Bracket Bolts24 lb-ft33 Nm
AC Compressor Oil Add5 specs
- AC Line FittingsUse new O-rings, add PAG oil15 lb-ft20 Nm
- Blower Motor Mounting Screw3 lb-ft4 Nm
- Compressor Bolts34 lb-ft46 Nm
- Duct Clips3 lb-ft4 Nm
- Mounting Bracket Bolts24 lb-ft33 Nm
AC Condenser2 specs
- AC Line FittingsUse new O-rings15 lb-ft20 Nm
- Condenser Mounting Bolts9 lb-ft12 Nm
AC Evaporator7 specs
- AC Line FittingsUse new O-rings, add PAG oil15 lb-ft20 Nm
- Blower Motor Mounting Screw7 lb-ft9 Nm
- Compressor Bolts34 lb-ft46 Nm
- Duct Clips3 lb-ft4 Nm
- Evaporator Case Screws4 lb-ft5 Nm
- Expansion Valve7 lb-ft10 Nm
- Mounting Bracket Bolts24 lb-ft33 Nm
AC Expansion Valve (TXV)6 specs
- AC Line FittingsUse new O-rings, add PAG oil15 lb-ft20 Nm
- Blower Motor Mounting Screw7 lb-ft9 Nm
- Compressor Bolts34 lb-ft46 Nm
- Duct Clips3 lb-ft4 Nm
- Expansion Valve7 lb-ft10 Nm
- Mounting Bracket Bolts24 lb-ft33 Nm
AC High Pressure Switch5 specs
- AC Line FittingsUse new O-rings, add PAG oil15 lb-ft20 Nm
- Blower Motor Mounting Screw3 lb-ft4 Nm
- Compressor Bolts34 lb-ft46 Nm
- Duct Clips3 lb-ft4 Nm
- Mounting Bracket Bolts24 lb-ft33 Nm
AC Hose - High Side5 specs
- AC Line FittingsUse new O-rings, add PAG oil15 lb-ft20 Nm
- Blower Motor Mounting Screw3 lb-ft4 Nm
- Compressor Bolts34 lb-ft46 Nm
- Duct Clips3 lb-ft4 Nm
- Mounting Bracket Bolts24 lb-ft33 Nm
AC Hose - Low Side6 specs
- AC Line FittingsUse new O-rings, add PAG oil15 lb-ft20 Nm
- Blower Motor Mounting Screw3 lb-ft4 Nm
- Compressor Bolts34 lb-ft46 Nm
- Duct Clips3 lb-ft4 Nm
- Hose Clamps2 lb-ft3 Nm
- Mounting Bracket Bolts24 lb-ft33 Nm
AC Hose Assembly6 specs
- AC Line FittingsUse new O-rings, add PAG oil15 lb-ft20 Nm
- Blower Motor Mounting Screw3 lb-ft4 Nm
- Compressor Bolts34 lb-ft46 Nm
- Duct Clips3 lb-ft4 Nm
- Hose Clamps2 lb-ft3 Nm
- Mounting Bracket Bolts24 lb-ft33 Nm
AC Low Pressure Switch5 specs
- AC Line FittingsUse new O-rings, add PAG oil15 lb-ft20 Nm
- Blower Motor Mounting Screw3 lb-ft4 Nm
- Compressor Bolts34 lb-ft46 Nm
- Duct Clips3 lb-ft4 Nm
- Mounting Bracket Bolts24 lb-ft33 Nm
AC Orifice Tube5 specs
- AC Line FittingsUse new O-rings, add PAG oil15 lb-ft20 Nm
- Blower Motor Mounting Screw3 lb-ft4 Nm
- Compressor Bolts34 lb-ft46 Nm
- Duct Clips3 lb-ft4 Nm
- Mounting Bracket Bolts24 lb-ft33 Nm
AC Pressure Sensor5 specs
- AC Line FittingsUse new O-rings, add PAG oil15 lb-ft20 Nm
- Blower Motor Mounting Screw3 lb-ft4 Nm
- Compressor Bolts34 lb-ft46 Nm
- Duct Clips3 lb-ft4 Nm
- Mounting Bracket Bolts24 lb-ft33 Nm
AC Receiver/Drier6 specs
- AC Line FittingsUse new O-rings, add PAG oil15 lb-ft20 Nm
- Blower Motor Mounting Screw7 lb-ft9 Nm
- Compressor Bolts34 lb-ft46 Nm
- Duct Clips3 lb-ft4 Nm
- Mounting Bracket Bolts24 lb-ft33 Nm
- Receiver Drier Bolts7 lb-ft10 Nm
AC Recharge4 specs
- Blower Motor Mounting Screw3 lb-ft4 Nm
- Compressor Bolts34 lb-ft46 Nm
- Duct Clips3 lb-ft4 Nm
- Mounting Bracket Bolts24 lb-ft33 Nm
Blend Door Actuator5 specs
- Actuator Screws2 lb-ft3 Nm
- Blower Motor Mounting Screw7 lb-ft9 Nm
- Compressor Bolts34 lb-ft46 Nm
- Duct Clips3 lb-ft4 Nm
- Mounting Bracket Bolts24 lb-ft33 Nm
Cabin Air Filter4 specs
- Compressor Bolts34 lb-ft46 Nm
- Connector Bolts7 lb-ft9 Nm
- Filter Cover ClipsTool-free on most3 lb-ft4 Nm
- Glove Box Screws4 lb-ft5 Nm
Climate Control Module4 specs
- Blower Motor Mounting Screw3 lb-ft4 Nm
- Compressor Bolts34 lb-ft46 Nm
- Duct Clips3 lb-ft4 Nm
- Mounting Bracket Bolts24 lb-ft33 Nm
HVAC Control Panel4 specs
- Blower Motor Mounting Screw3 lb-ft4 Nm
- Compressor Bolts34 lb-ft46 Nm
- Duct Clips3 lb-ft4 Nm
- Mounting Bracket Bolts24 lb-ft33 Nm
Mode Door Actuator4 specs
- Blower Motor Mounting Screw3 lb-ft4 Nm
- Compressor Bolts34 lb-ft46 Nm
- Duct Clips3 lb-ft4 Nm
- Mounting Bracket Bolts24 lb-ft33 Nm
Recirculation Door Actuator4 specs
- Blower Motor Mounting Screw3 lb-ft4 Nm
- Compressor Bolts34 lb-ft46 Nm
- Duct Clips3 lb-ft4 Nm
- Mounting Bracket Bolts24 lb-ft33 Nm
Body
Bed Rail Cap6 specs
- Body Panel Bolts18 lb-ft25 Nm
- Hinge Bolts27 lb-ft37 Nm
- Latch Bolts14 lb-ft19 Nm
- Panel Bolts14 lb-ft19 Nm
- Striker Bolts34 lb-ft46 Nm
- Trim ClipsReplace if broken3 lb-ft4 Nm
Bedside Panel7 specs
- Body Panel Bolts18 lb-ft25 Nm
- Bumper Cover Bolts7 lb-ft10 Nm
- Hinge Bolts27 lb-ft37 Nm
- Latch Bolts14 lb-ft19 Nm
- Panel Bolts14 lb-ft19 Nm
- Striker Bolts34 lb-ft46 Nm
- Trim ClipsReplace if broken3 lb-ft4 Nm
Bumper Cover - Front8 specs
- Bumper Cover Bolts7 lb-ft10 Nm
- Fender Liner Screws2 lb-ft3 Nm
- Grille Clips4 lb-ft5 Nm
- Hinge Bolts27 lb-ft37 Nm
- Latch Bolts14 lb-ft19 Nm
- Panel Bolts14 lb-ft19 Nm
- Striker Bolts34 lb-ft46 Nm
- Trim ClipsReplace if broken3 lb-ft4 Nm
Bumper Cover - Rear7 specs
- Bumper Cover Bolts7 lb-ft10 Nm
- Hinge Bolts27 lb-ft37 Nm
- Latch Bolts14 lb-ft19 Nm
- Panel Bolts14 lb-ft19 Nm
- Striker Bolts34 lb-ft46 Nm
- Trim ClipsReplace if broken3 lb-ft4 Nm
- Trunk Liner Screws2 lb-ft3 Nm
Bumper Reinforcement - Front7 specs
- Body Panel Bolts18 lb-ft25 Nm
- Bumper Cover Bolts7 lb-ft10 Nm
- Hinge Bolts27 lb-ft37 Nm
- Latch Bolts14 lb-ft19 Nm
- Panel Bolts14 lb-ft19 Nm
- Striker Bolts34 lb-ft46 Nm
- Trim ClipsReplace if broken3 lb-ft4 Nm
Bumper Reinforcement - Rear7 specs
- Body Panel Bolts18 lb-ft25 Nm
- Bumper Cover Bolts7 lb-ft10 Nm
- Hinge Bolts27 lb-ft37 Nm
- Latch Bolts14 lb-ft19 Nm
- Panel Bolts14 lb-ft19 Nm
- Striker Bolts34 lb-ft46 Nm
- Trim ClipsReplace if broken3 lb-ft4 Nm
Door Check/Stop6 specs
- Body Panel Bolts18 lb-ft25 Nm
- Hinge Bolts27 lb-ft37 Nm
- Latch Bolts14 lb-ft19 Nm
- Panel Bolts14 lb-ft19 Nm
- Striker Bolts34 lb-ft46 Nm
- Trim ClipsReplace if broken3 lb-ft4 Nm
Door Glass5 specs
- Hinge Bolts27 lb-ft37 Nm
- Latch Bolts14 lb-ft19 Nm
- Panel Bolts14 lb-ft19 Nm
- Striker Bolts34 lb-ft46 Nm
- Trim ClipsReplace if broken3 lb-ft4 Nm
Door Handle - Exterior7 specs
- Handle Mounting Bolts6 lb-ft8 Nm
- Hinge Bolts27 lb-ft37 Nm
- Latch Bolts14 lb-ft19 Nm
- Lock Rod Clips4 lb-ft5 Nm
- Panel Bolts14 lb-ft19 Nm
- Striker Bolts34 lb-ft46 Nm
- Trim ClipsReplace if broken3 lb-ft4 Nm
Door Handle - Interior7 specs
- Cable Clips4 lb-ft5 Nm
- Handle Screws2 lb-ft3 Nm
- Hinge Bolts27 lb-ft37 Nm
- Latch Bolts14 lb-ft19 Nm
- Panel Bolts14 lb-ft19 Nm
- Striker Bolts34 lb-ft46 Nm
- Trim ClipsReplace if broken3 lb-ft4 Nm
Door Hinge6 specs
- Door Hinge Bolts22 lb-ft30 Nm
- Hinge Bolts27 lb-ft37 Nm
- Latch Bolts14 lb-ft19 Nm
- Panel Bolts14 lb-ft19 Nm
- Striker Bolts34 lb-ft46 Nm
- Trim ClipsReplace if broken3 lb-ft4 Nm
Door Shell7 specs
- Body Panel Bolts18 lb-ft25 Nm
- Door Hinge Bolts22 lb-ft30 Nm
- Hinge Bolts27 lb-ft37 Nm
- Latch Bolts14 lb-ft19 Nm
- Panel Bolts14 lb-ft19 Nm
- Striker Bolts34 lb-ft46 Nm
- Trim ClipsReplace if broken3 lb-ft4 Nm
Door Skin7 specs
- Body Panel Bolts18 lb-ft25 Nm
- Door Hinge Bolts22 lb-ft30 Nm
- Hinge Bolts27 lb-ft37 Nm
- Latch Bolts14 lb-ft19 Nm
- Panel Bolts14 lb-ft19 Nm
- Striker Bolts34 lb-ft46 Nm
- Trim ClipsReplace if broken3 lb-ft4 Nm
Door Weatherstrip5 specs
- Hinge Bolts27 lb-ft37 Nm
- Latch Bolts14 lb-ft19 Nm
- Panel Bolts14 lb-ft19 Nm
- Striker Bolts34 lb-ft46 Nm
- Trim ClipsReplace if broken3 lb-ft4 Nm
Fender8 specs
- Fender Bolts9 lb-ft12 Nm
- Fender Liner Screws2 lb-ft3 Nm
- Hinge Bolts27 lb-ft37 Nm
- Hood Hinge Bolts18 lb-ft25 Nm
- Latch Bolts14 lb-ft19 Nm
- Panel Bolts14 lb-ft19 Nm
- Striker Bolts34 lb-ft46 Nm
- Trim ClipsReplace if broken3 lb-ft4 Nm
Fender Liner7 specs
- Body Panel Bolts18 lb-ft25 Nm
- Bumper Cover Bolts7 lb-ft10 Nm
- Hinge Bolts27 lb-ft37 Nm
- Latch Bolts14 lb-ft19 Nm
- Panel Bolts14 lb-ft19 Nm
- Striker Bolts34 lb-ft46 Nm
- Trim ClipsReplace if broken3 lb-ft4 Nm
Grille7 specs
- Clips4 lb-ft5 Nm
- Grille Mounting Screws2 lb-ft3 Nm
- Hinge Bolts27 lb-ft37 Nm
- Latch Bolts14 lb-ft19 Nm
- Panel Bolts14 lb-ft19 Nm
- Striker Bolts34 lb-ft46 Nm
- Trim ClipsReplace if broken3 lb-ft4 Nm
Hood8 specs
- Hinge Bolts27 lb-ft37 Nm
- Hood Hinge Bolts18 lb-ft25 Nm
- Hood Latch Bolts9 lb-ft12 Nm
- Hood Strut Bolts7 lb-ft10 Nm
- Latch Bolts14 lb-ft19 Nm
- Panel Bolts14 lb-ft19 Nm
- Striker Bolts34 lb-ft46 Nm
- Trim ClipsReplace if broken3 lb-ft4 Nm
Hood Hinge6 specs
- Body Panel Bolts18 lb-ft25 Nm
- Hinge Bolts27 lb-ft37 Nm
- Latch Bolts14 lb-ft19 Nm
- Panel Bolts14 lb-ft19 Nm
- Striker Bolts34 lb-ft46 Nm
- Trim ClipsReplace if broken3 lb-ft4 Nm
Hood Latch7 specs
- Cable Clips4 lb-ft5 Nm
- Hinge Bolts27 lb-ft37 Nm
- Hood Latch Bolts9 lb-ft12 Nm
- Latch Bolts14 lb-ft19 Nm
- Panel Bolts14 lb-ft19 Nm
- Striker Bolts34 lb-ft46 Nm
- Trim ClipsReplace if broken3 lb-ft4 Nm
Hood Release Cable7 specs
- Body Panel Bolts18 lb-ft25 Nm
- Bumper Cover Bolts7 lb-ft10 Nm
- Hinge Bolts27 lb-ft37 Nm
- Latch Bolts14 lb-ft19 Nm
- Panel Bolts14 lb-ft19 Nm
- Striker Bolts34 lb-ft46 Nm
- Trim ClipsReplace if broken3 lb-ft4 Nm
Hood Strut6 specs
- Body Panel Bolts18 lb-ft25 Nm
- Hinge Bolts27 lb-ft37 Nm
- Latch Bolts14 lb-ft19 Nm
- Panel Bolts14 lb-ft19 Nm
- Striker Bolts34 lb-ft46 Nm
- Trim ClipsReplace if broken3 lb-ft4 Nm
Quarter Glass6 specs
- Body Panel Bolts18 lb-ft25 Nm
- Hinge Bolts27 lb-ft37 Nm
- Latch Bolts14 lb-ft19 Nm
- Panel Bolts14 lb-ft19 Nm
- Striker Bolts34 lb-ft46 Nm
- Trim ClipsReplace if broken3 lb-ft4 Nm
Quarter Panel8 specs
- Body Panel Bolts18 lb-ft25 Nm
- Bumper Cover Bolts7 lb-ft10 Nm
- Door Hinge Bolts22 lb-ft30 Nm
- Hinge Bolts27 lb-ft37 Nm
- Latch Bolts14 lb-ft19 Nm
- Panel Bolts14 lb-ft19 Nm
- Striker Bolts34 lb-ft46 Nm
- Trim ClipsReplace if broken3 lb-ft4 Nm
Rear Window6 specs
- Body Panel Bolts18 lb-ft25 Nm
- Hinge Bolts27 lb-ft37 Nm
- Latch Bolts14 lb-ft19 Nm
- Panel Bolts14 lb-ft19 Nm
- Striker Bolts34 lb-ft46 Nm
- Trim ClipsReplace if broken3 lb-ft4 Nm
Rocker Panel8 specs
- Body Panel Bolts18 lb-ft25 Nm
- Bumper Cover Bolts7 lb-ft10 Nm
- Door Hinge Bolts22 lb-ft30 Nm
- Hinge Bolts27 lb-ft37 Nm
- Latch Bolts14 lb-ft19 Nm
- Panel Bolts14 lb-ft19 Nm
- Striker Bolts34 lb-ft46 Nm
- Trim ClipsReplace if broken3 lb-ft4 Nm
Side Mirror Glass5 specs
- Hinge Bolts27 lb-ft37 Nm
- Latch Bolts14 lb-ft19 Nm
- Panel Bolts14 lb-ft19 Nm
- Striker Bolts34 lb-ft46 Nm
- Trim ClipsReplace if broken3 lb-ft4 Nm
Tailgate7 specs
- Body Panel Bolts18 lb-ft25 Nm
- Door Hinge Bolts22 lb-ft30 Nm
- Hinge Bolts27 lb-ft37 Nm
- Latch Bolts14 lb-ft19 Nm
- Panel Bolts14 lb-ft19 Nm
- Striker Bolts34 lb-ft46 Nm
- Trim ClipsReplace if broken3 lb-ft4 Nm
Tailgate Cable5 specs
- Hinge Bolts27 lb-ft37 Nm
- Latch Bolts14 lb-ft19 Nm
- Panel Bolts14 lb-ft19 Nm
- Striker Bolts34 lb-ft46 Nm
- Trim ClipsReplace if broken3 lb-ft4 Nm
Tailgate Handle5 specs
- Hinge Bolts27 lb-ft37 Nm
- Latch Bolts14 lb-ft19 Nm
- Panel Bolts14 lb-ft19 Nm
- Striker Bolts34 lb-ft46 Nm
- Trim ClipsReplace if broken3 lb-ft4 Nm
Tonneau Cover Install6 specs
- Body Panel Bolts18 lb-ft25 Nm
- Hinge Bolts27 lb-ft37 Nm
- Latch Bolts14 lb-ft19 Nm
- Panel Bolts14 lb-ft19 Nm
- Striker Bolts34 lb-ft46 Nm
- Trim ClipsReplace if broken3 lb-ft4 Nm
Truck Bed Liner6 specs
- Body Panel Bolts18 lb-ft25 Nm
- Hinge Bolts27 lb-ft37 Nm
- Latch Bolts14 lb-ft19 Nm
- Panel Bolts14 lb-ft19 Nm
- Striker Bolts34 lb-ft46 Nm
- Trim ClipsReplace if broken3 lb-ft4 Nm
Windshield6 specs
- Body Panel Bolts18 lb-ft25 Nm
- Hinge Bolts27 lb-ft37 Nm
- Latch Bolts14 lb-ft19 Nm
- Panel Bolts14 lb-ft19 Nm
- Striker Bolts34 lb-ft46 Nm
- Trim ClipsReplace if broken3 lb-ft4 Nm
Windshield Molding5 specs
- Hinge Bolts27 lb-ft37 Nm
- Latch Bolts14 lb-ft19 Nm
- Panel Bolts14 lb-ft19 Nm
- Striker Bolts34 lb-ft46 Nm
- Trim ClipsReplace if broken3 lb-ft4 Nm
Interior
Armrest2 specs
- Connector Bolts7 lb-ft9 Nm
- Trim Panel ClipsReplace if damaged1.5 lb-ft2 Nm
Carpet4 specs
- Connector Bolts7 lb-ft9 Nm
- Dashboard Screws2 lb-ft3 Nm
- Seat Mounting BoltsSafety critical33 lb-ft45 Nm
- Trim Panel ClipsReplace if damaged1.5 lb-ft2 Nm
Center Console3 specs
- Connector Bolts7 lb-ft9 Nm
- Console Screws2 lb-ft3 Nm
- Shifter Trim4 lb-ft5 Nm
Dash Pad4 specs
- Connector Bolts7 lb-ft9 Nm
- Dashboard Screws2 lb-ft3 Nm
- Seat Mounting BoltsSafety critical33 lb-ft45 Nm
- Trim Panel ClipsReplace if damaged1.5 lb-ft2 Nm
Dashboard4 specs
- Connector Bolts7 lb-ft9 Nm
- Dashboard Bolt9 lb-ft12 Nm
- Dashboard Screws2 lb-ft3 Nm
- Trim Panel ClipsReplace if damaged1.5 lb-ft2 Nm
Door Panel3 specs
- Connector Bolts7 lb-ft9 Nm
- Door Panel Screws1.5 lb-ft2 Nm
- Trim Panel ClipsReplace if damaged1.5 lb-ft2 Nm
Floor Mat Hooks2 specs
- Connector Bolts7 lb-ft9 Nm
- Trim Panel ClipsReplace if damaged1.5 lb-ft2 Nm
Glove Box3 specs
- Connector Bolts7 lb-ft9 Nm
- Glove Box Screws2 lb-ft3 Nm
- Hinge Screws1.5 lb-ft2 Nm
Glove Box Latch3 specs
- Connector Bolts7 lb-ft9 Nm
- Dashboard Screws2 lb-ft3 Nm
- Trim Panel ClipsReplace if damaged1.5 lb-ft2 Nm
Headliner3 specs
- Connector Bolts7 lb-ft9 Nm
- Seat Mounting BoltsSafety critical33 lb-ft45 Nm
- Trim Panel ClipsReplace if damaged1.5 lb-ft2 Nm
Pedal Pads2 specs
- Connector Bolts7 lb-ft9 Nm
- Trim Panel ClipsReplace if damaged1.5 lb-ft2 Nm
Rearview Mirror2 specs
- Connector Bolts7 lb-ft9 Nm
- Trim Panel ClipsReplace if damaged1.5 lb-ft2 Nm
Seat - Front4 specs
- Connector Bolts7 lb-ft9 Nm
- Electrical Connectors4 lb-ft5 Nm
- Seat Mounting BoltsSafety critical33 lb-ft45 Nm
- Seat Track Bolts33 lb-ft45 Nm
Seat - Rear3 specs
- Connector Bolts7 lb-ft9 Nm
- Seat Back Release11 lb-ft15 Nm
- Seat Mounting Bolts26 lb-ft35 Nm
Seat Belt3 specs
- Connector Bolts7 lb-ft9 Nm
- Seat Mounting BoltsSafety critical33 lb-ft45 Nm
- Trim Panel ClipsReplace if damaged1.5 lb-ft2 Nm
Seat Belt Buckle3 specs
- Connector Bolts7 lb-ft9 Nm
- Seat Mounting BoltsSafety critical33 lb-ft45 Nm
- Trim Panel ClipsReplace if damaged1.5 lb-ft2 Nm
Seat Belt Pretensioner3 specs
- Connector Bolts7 lb-ft9 Nm
- Seat Mounting BoltsSafety critical33 lb-ft45 Nm
- Trim Panel ClipsReplace if damaged1.5 lb-ft2 Nm
Seat Cover3 specs
- Connector Bolts7 lb-ft9 Nm
- Seat Mounting BoltsSafety critical33 lb-ft45 Nm
- Trim Panel ClipsReplace if damaged1.5 lb-ft2 Nm
Seat Foam3 specs
- Connector Bolts7 lb-ft9 Nm
- Seat Mounting BoltsSafety critical33 lb-ft45 Nm
- Trim Panel ClipsReplace if damaged1.5 lb-ft2 Nm
Seat Track3 specs
- Connector Bolts7 lb-ft9 Nm
- Seat Mounting BoltsSafety critical33 lb-ft45 Nm
- Trim Panel ClipsReplace if damaged1.5 lb-ft2 Nm
Shifter Boot2 specs
- Connector Bolts7 lb-ft9 Nm
- Trim Panel ClipsReplace if damaged1.5 lb-ft2 Nm
Shifter Knob2 specs
- Connector Bolts7 lb-ft9 Nm
- Trim Panel ClipsReplace if damaged1.5 lb-ft2 Nm
Steering Wheel Cover2 specs
- Connector Bolts7 lb-ft9 Nm
- Trim Panel ClipsReplace if damaged. Verify sequence with the service manual1.5 lb-ft2 Nm
Sun Visor2 specs
- Connector Bolts7 lb-ft9 Nm
- Visor Mounting Screws2 lb-ft3 Nm
Torque is shown in lb-ft with Nm below it. Where a step says to turn, tighten the listed angle after the torque step before it. Use new bolts where the note says so.
Need labor times, fluids or repair steps for this car? See it on the Open Labor Project