RQUE SPECS2017-2026 Volkswagen T-Roc torque specs
2.0L TDI
These specs cover the Volkswagen T-Roc 2.0L TDI for model years 2017, 2018, 2019, 2020, 2021, 2022, 2023, 2024, 2025, 2026.
Change vehicle
Most looked up
- Lug nuts89 lb-ft120.7 Nm
- Oil drain plug22 lb-ft30 Nm
- Front caliper bracket bolts88 lb-ft120 Nm
- Rear caliper bracket bolts74 lb-ft100 Nm
- Front axle nut184 lb-ft250 Nm
- Outer tie rod end nut36.9 lb-ft50 Nm
Maintenance
Tire Rotation2 specs
- Lug Nuts - Alloy WheelsTorque in star pattern, recheck after 50 miles89 lb-ft120.7 Nm
- Lug Nuts - Steel WheelsTorque in star pattern89 lb-ft120.7 Nm
Brakes
Brake Caliper - Front3 specs
- Bleeder ScrewDo not overtighten7 lb-ft10 Nm
- Brake Line Banjo BoltUse new copper washers18 lb-ft25 Nm
- Caliper Bracket BoltsThreadlocker recommended88 lb-ft120 Nm
Brake Caliper - Rear3 specs
- Bleeder ScrewDo not overtighten7 lb-ft10 Nm
- Brake Line Banjo BoltUse new copper washers18 lb-ft25 Nm
- Caliper Bracket BoltsThreadlocker recommended74 lb-ft100 Nm
Brake Master Cylinder2 specs
- Brake Line FittingsUse flare nut wrench11 lb-ft15 Nm
- Master Cylinder Nuts18 lb-ft25 Nm
Brake Master Cylinder Rebuild3 specs
- Brake Line FittingsUse flare nut wrench11 lb-ft15 Nm
- Master Cylinder Mounting Nuts18 lb-ft25 Nm
- Reservoir Mounting Bolts6 lb-ft8 Nm
Brake Pads - Front3 specs
- Caliper Bracket BoltsThreadlocker recommended88 lb-ft120 Nm
- Caliper Slide Pin BoltsApply silicone brake grease26 lb-ft35 Nm
- Wheel Lug NutsTorque in star pattern89 lb-ft120.7 Nm
Brake Pads - Rear3 specs
- Caliper Bracket BoltsThreadlocker recommended74 lb-ft100 Nm
- Caliper Slide Pin BoltsApply silicone brake grease22 lb-ft30 Nm
- Wheel Lug NutsTorque in star pattern89 lb-ft120.7 Nm
Brake Pads and Rotors - Front3 specs
- Caliper Bracket Bolts75.2 lb-ft102 Nm
- Caliper Slide Pins26.6 lb-ft36 Nm
- Wheel Nuts80.4 lb-ft109 Nm
Brake Pads and Rotors - Rear3 specs
- Caliper Bracket Bolts73 lb-ft99 Nm
- Caliper Slide Pins25.1 lb-ft34 Nm
- Wheel Nuts84.8 lb-ft115 Nm
Brake Rotor - Front Single2 specs
- Brake Rotor Set Screw5.9 lb-ft8 Nm
- Caliper Bracket Bolts74.5 lb-ft101 Nm
Brake Rotor - Rear Single2 specs
- Brake Rotor Set Screw5.9 lb-ft8 Nm
- Caliper Bracket Bolts76.7 lb-ft104 Nm
Brake Rotors - Front Pair2 specs
- Brake Rotor Set Screw5.9 lb-ft8 Nm
- Caliper Bracket Bolts72.3 lb-ft98 Nm
Brake Rotors - Rear Pair2 specs
- Brake Rotor Set Screw5.9 lb-ft8 Nm
- Caliper Bracket Bolts76 lb-ft103 Nm
Front Brake Pad Replacement3 specs
- Caliper Bracket BoltsThreadlocker recommended88 lb-ft120 Nm
- Caliper Slide Pin BoltsApply silicone brake grease26 lb-ft35 Nm
- Wheel Lug NutsTorque in star pattern89 lb-ft120.7 Nm
Rear Brake Shoe Replacement3 specs
- Backing Plate Bolts44 lb-ft60 Nm
- Wheel Cylinder Bolts9 lb-ft12 Nm
- Wheel Lug NutsTorque in star pattern89 lb-ft120.7 Nm
Engine
Engine Mount - Front3 specs
- Engine Mount Through-Bolt63 lb-ft85 Nm
- Engine Mount-to-Block Bolts48 lb-ft65 Nm
- Engine Mount-to-Frame Bolts55 lb-ft75 Nm
Engine Mount - Rear1 spec
- Engine Mount Through-Bolt73 lb-ft99 Nm
Engine Mounts - All1 spec
- Engine Mount Through-Bolt75.2 lb-ft102 Nm
Exhaust Manifold Gasket3 specs
- Exhaust Manifold NutsApply anti-seize, work hot-to-cold22 lb-ft30 Nm
- Exhaust Manifold StudsIf replacing studs11 lb-ft15 Nm
- Heat Shield Bolts7 lb-ft10 Nm
Fan Belt Replacement3 specs
- Idler Pulley Bolt30 lb-ft40 Nm
- Tensioner Bolt18 lb-ft25 Nm
- Tensioner Pulley Bolt33 lb-ft45 Nm
Flywheel2 specs
- Flexplate BoltsAutomatic transmissions63 lb-ft85 Nm
- Flywheel BoltsOften TTY - check specs, tighten in star pattern70 lb-ft95 Nm
Full Engine Tune-Up3 specs
- Ignition Coil Bolt6 lb-ft8 Nm
- Throttle Body Bolts7 lb-ft10 Nm
- Valve Cover BoltsTighten in sequence7 lb-ft10 Nm
Glow Plugs - Replace All1 spec
- Glow PlugsHand-start, then torque. Over-torque snaps the tip; a seized plug needs extraction11.1 lb-ft15 Nm
Head Gasket - Single6 specs
- Exhaust Manifold NutsApply anti-seize18 lb-ft25 Nm
- Intake Manifold BoltTighten in sequence18 lb-ft25 Nm
- Cylinder Head Bolts - Step 1Always use new TTY bolts30 lb-ft40 Nm
- Cylinder Head Bolts - Step 2Tighten in sequence59 lb-ft80 Nm
- Cylinder Head Bolts - Step 3Plus 90 degreesTurn 90°
- Cylinder Head Bolts - Step 4Plus 90 degreesTurn 90°
Head Gaskets - Both2 specs
- Head Bolts35.4 lb-ft48 Nm
- Intake Manifold17.7 lb-ft24 Nm
Intake Manifold Gasket3 specs
- Fuel Rail Bolts9 lb-ft12 Nm
- Intake Manifold BoltTighten in sequence from center out18 lb-ft25 Nm
- Throttle Body Bolts7 lb-ft10 Nm
Oil Change2 specs
- Oil Drain PlugUse new crush washer22 lb-ft30 Nm
- Oil Filter Housing CapFor cartridge-type filters18 lb-ft25 Nm
Oil Pan Gasket2 specs
- Oil Drain PlugUse new crush washer26 lb-ft35 Nm
- Oil Pan BoltTighten in sequence from center outward9 lb-ft12 Nm
Serpentine Belt2 specs
- Belt Tensioner Bolt41 lb-ft55 Nm
- Idler Pulley Bolt33 lb-ft45 Nm
Throttle Body2 specs
- Air Intake Hose Clamps2 lb-ft3 Nm
- Throttle Body Bolts7 lb-ft10 Nm
Transmission Mount2 specs
- Crossmember Bolt70 lb-ft95 Nm
- Transmission Mount Bolts48 lb-ft65 Nm
Valve Cover Gasket - Single2 specs
- Spark Plug Tube SealsIf equipped with separate seals9 lb-ft12 Nm
- Valve Cover BoltsTighten in sequence7 lb-ft10 Nm
Valve Cover Gaskets - Both1 spec
- Valve Cover Bolts8.9 lb-ft12 Nm
Cooling
Coolant Flush2 specs
- Block Drain PlugIf equipped, use new washer18 lb-ft25 Nm
- Drain PetcockPlastic - hand-tight only4 lb-ft5 Nm
Cooling Fan Clutch2 specs
- Flywheel Bolts59 lb-ft80 Nm
- Pressure Plate19.2 lb-ft26 Nm
Radiator4 specs
- Drain PetcockPlastic - hand tight4 lb-ft5 Nm
- Radiator Mounting BoltDo not overtighten plastic mounts9 lb-ft12 Nm
- Transmission Cooler LinesIf equipped18 lb-ft25 Nm
- Upper/Lower Hose Clamps2 lb-ft3 Nm
Radiator Removal and Service4 specs
- Drain PetcockPlastic - hand-tight only4 lb-ft5 Nm
- Fan Shroud Bolts7 lb-ft10 Nm
- Radiator Mounting BoltDo not overtighten plastic mounts9 lb-ft12 Nm
- Transmission Cooler LinesIf equipped, use new washers18 lb-ft25 Nm
Thermostat2 specs
- Coolant Temperature SensorUse thread sealant15 lb-ft20 Nm
- Thermostat Housing Bolt11 lb-ft15 Nm
Water Pump3 specs
- Hose ClampsSpring clamps preferred2 lb-ft3 Nm
- Thermostat Housing Bolt11 lb-ft15 Nm
- Water Pump BoltsTighten in criss-cross pattern18 lb-ft25 Nm
Fuel system
Fuel Filter2 specs
- Fuel Filter Bracket Bolt7 lb-ft10 Nm
- Fuel Line FittingsIf threaded type18 lb-ft25 Nm
Fuel Pump2 specs
- Fuel Pump Module Lock RingUse special tool59 lb-ft80 Nm
- Tank Strap Bolts26 lb-ft35 Nm
Electrical
Alternator4 specs
- Alternator Mounting Bolts37 lb-ft50 Nm
- Alternator Pivot Bolt18 lb-ft25 Nm
- Battery Terminal BoltsDo not overtighten6 lb-ft8 Nm
- Serpentine Belt Tensioner41 lb-ft55 Nm
Battery3 specs
- Battery Hold-Down Bolt6 lb-ft8 Nm
- Battery Terminal BoltsDo not overtighten - can crack terminal4 lb-ft6 Nm
- Battery Tray Bolts9 lb-ft12 Nm
Blower Motor2 specs
- Blower Motor Mounting Screw3 lb-ft4 Nm
- Blower Motor Resistor Screws1.5 lb-ft2 Nm
Starter3 specs
- Heat Shield BoltsIf equipped7 lb-ft10 Nm
- Starter Mounting BoltLong bolt may need extension37 lb-ft50 Nm
- Starter Solenoid NutFor B+ cable9 lb-ft12 Nm
Suspension
Ball Joint - Lower1 spec
- Lower Ball Joint Nut53.1 lb-ft72 Nm
Ball Joints - Upper and Lower1 spec
- Lower Ball Joint Nut52.4 lb-ft71 Nm
Control Arm Bushing - Front Lower2 specs
- Lower Ball Joint52.4 lb-ft71 Nm
- Pivot Bolts84.8 lb-ft115 Nm
Control Arm Bushing - Rear2 specs
- Ball Joint52.4 lb-ft71 Nm
- Pivot Bolts92.9 lb-ft126 Nm
Front Struts - Pair2 specs
- Pinch Bolt59 lb-ft80 Nm
- Strut Mount Nuts35.4 lb-ft48 Nm
Front Suspension Rebuild4 specs
- Ball Joint Pinch BoltUse new bolt if locknut style37 lb-ft50 Nm
- Lower Control Arm BoltsTorque at ride height81 lb-ft110 Nm
- Strut Top Mount Nuts18 lb-ft25 Nm
- Sway Bar End Link Nuts44 lb-ft60 Nm
Lower Control Arm - Front2 specs
- Lower Ball Joint49.4 lb-ft67 Nm
- Pivot Bolts86.3 lb-ft117 Nm
Lower Control Arm - Rear2 specs
- Lower Ball Joint53.1 lb-ft72 Nm
- Pivot Bolts90.7 lb-ft123 Nm
Rear Suspension Service4 specs
- Lower Control Arm BoltsTorque at ride height66 lb-ft90 Nm
- Shock Lower Bolt52 lb-ft70 Nm
- Sway Bar End Link Nuts37 lb-ft50 Nm
- Trailing Arm BoltsTorque at ride height88 lb-ft120 Nm
Shock Absorber Replacement2 specs
- Lower Mount Bolt66 lb-ft90 Nm
- Upper Mount NutUse new self-locking nut41 lb-ft55 Nm
Strut Assembly - Rear2 specs
- Pinch Bolt60.5 lb-ft82 Nm
- Strut Mount Nuts36.9 lb-ft50 Nm
Strut Bearing2 specs
- Pinch Bolt56.1 lb-ft76 Nm
- Strut Mount Nuts37.6 lb-ft51 Nm
Strut Mount - Front2 specs
- Pinch Bolt60.5 lb-ft82 Nm
- Strut Mount Nuts38.4 lb-ft52 Nm
Strut Mount - Rear2 specs
- Pinch Bolt57.5 lb-ft78 Nm
- Strut Mount Nuts36.9 lb-ft50 Nm
Sway Bar - Front1 spec
- Link Nuts36.9 lb-ft50 Nm
Sway Bar - Rear1 spec
- Link Nuts37.6 lb-ft51 Nm
Sway Bar Bushing - Front1 spec
- Link Nuts36.9 lb-ft50 Nm
Sway Bar Bushing - Rear1 spec
- Link Nuts38.4 lb-ft52 Nm
Sway Bar Link - Front1 spec
- Link Nuts37.6 lb-ft51 Nm
Sway Bar Link - Rear1 spec
- Link Nuts35.4 lb-ft48 Nm
Sway Bar Links - Front Pair1 spec
- Link Nuts35.4 lb-ft48 Nm
Upper Control Arm - Rear2 specs
- Pivot Bolts91.5 lb-ft124 Nm
- Upper Ball Joint51.6 lb-ft70 Nm
Steering
Tie Rod Assembly2 specs
- Jam Nut52.4 lb-ft71 Nm
- Tie Rod Nut36.9 lb-ft50 Nm
Tie Rod End - Inner2 specs
- Jam Nut49.4 lb-ft67 Nm
- Tie Rod Nut36.9 lb-ft50 Nm
Tie Rod End - Outer2 specs
- Jam Nut52.4 lb-ft71 Nm
- Tie Rod Nut36.1 lb-ft49 Nm
Tie Rods - Both Sides2 specs
- Jam Nut53.8 lb-ft73 Nm
- Tie Rod Nut37.6 lb-ft51 Nm
Drivetrain
CV Axle - Front2 specs
- Axle Nut196.9 lb-ft267 Nm
- Lower Ball Joint50.9 lb-ft69 Nm
CV Axle - Rear2 specs
- Axle Nut215.4 lb-ft292 Nm
- Ball Joint49.4 lb-ft67 Nm
CV Axles - Front Pair2 specs
- Axle Nut202.1 lb-ft274 Nm
- Lower Ball Joint51.6 lb-ft70 Nm
Driveshaft - Front3 specs
- Center Support Bearing Bracket Bolts37 lb-ft50 Nm
- Driveshaft Flange Bolts (CV/U-Joint)Use new bolts if torque-to-yield55 lb-ft75 Nm
- Transfer Case Output Yoke NutIf accessible133 lb-ft180 Nm
Driveshaft - Rear3 specs
- Differential Pinion Yoke NutUse new nut, set pinion preload184 lb-ft250 Nm
- Driveshaft Flange Bolts55 lb-ft75 Nm
- U-Joint Strap BoltsApply threadlocker26 lb-ft35 Nm
Driveshaft Center Support Bearing2 specs
- Center Support Bearing Bracket Bolts37 lb-ft50 Nm
- Driveshaft Flange Bolts55 lb-ft75 Nm
Limited Slip Clutch Pack2 specs
- Flywheel Bolts57.5 lb-ft78 Nm
- Pressure Plate19.2 lb-ft26 Nm
Wheel Bearing - Press-In Front2 specs
- Bearing Bolts47.9 lb-ft65 Nm
- Hub Nut216.9 lb-ft294 Nm
Wheel Bearing - Press-In Rear2 specs
- Bearing Bolts48.7 lb-ft66 Nm
- Hub Nut197.7 lb-ft268 Nm
Wheel Bearing Hub - Front6 specs
- ABS Sensor BoltDo not overtighten7 lb-ft10 Nm
- Axle NutUse new cotter pin after torque184 lb-ft250 Nm
- Bearing Bolts49.4 lb-ft67 Nm
- Caliper Bracket Bolts88 lb-ft120 Nm
- Hub Nut208 lb-ft282 Nm
- Wheel Bearing Hub BoltsApply threadlocker if specified81 lb-ft110 Nm
Wheel Bearing Hub - Rear5 specs
- Axle NutUse new cotter pin after torque148 lb-ft200 Nm
- Bearing Bolts46.5 lb-ft63 Nm
- Caliper Bracket Bolts81 lb-ft110 Nm
- Hub Nut210.2 lb-ft285 Nm
- Wheel Bearing Hub BoltsApply threadlocker if specified74 lb-ft100 Nm
Transmission
Clutch Cable2 specs
- Flywheel Bolts60.5 lb-ft82 Nm
- Pressure Plate18.4 lb-ft25 Nm
Clutch Disc2 specs
- Flywheel Bolts62 lb-ft84 Nm
- Pressure Plate18.4 lb-ft25 Nm
Clutch Hydraulic Line2 specs
- Flywheel Bolts58.3 lb-ft79 Nm
- Pressure Plate19.2 lb-ft26 Nm
Clutch Kit2 specs
- Flywheel Bolts56.1 lb-ft76 Nm
- Pressure Plate19.2 lb-ft26 Nm
Clutch Master Cylinder2 specs
- Flywheel Bolts60.5 lb-ft82 Nm
- Pressure Plate18.4 lb-ft25 Nm
Clutch Slave Cylinder2 specs
- Flywheel Bolts56.8 lb-ft77 Nm
- Pressure Plate19.2 lb-ft26 Nm
Transmission Fluid Change3 specs
- Transmission Drain PlugUse new crush washer if equipped22 lb-ft30 Nm
- Transmission Filter BoltsIf equipped with bolted filter6 lb-ft8 Nm
- Transmission Pan BoltsTighten in criss-cross pattern9 lb-ft12 Nm
Exhaust
Muffler2 specs
- Hanger Bracket Bolts18 lb-ft25 Nm
- Muffler Clamps41 lb-ft55 Nm
Heating and A/C
AC Clutch Coil2 specs
- Flywheel Bolts60.5 lb-ft82 Nm
- Pressure Plate19.2 lb-ft26 Nm
AC Compressor3 specs
- AC Compressor Bolts18 lb-ft25 Nm
- AC Line FittingsUse new O-rings, add PAG oil15 lb-ft20 Nm
- Clutch Connector Bolt6 lb-ft8 Nm
AC Compressor Clutch2 specs
- Flywheel Bolts58.3 lb-ft79 Nm
- Pressure Plate18.4 lb-ft25 Nm
AC Condenser2 specs
- AC Line FittingsUse new O-rings15 lb-ft20 Nm
- Condenser Mounting Bolts9 lb-ft12 Nm
Body
Hood Strut2 specs
- Pinch Bolt56.1 lb-ft76 Nm
- Strut Mount Nuts38.4 lb-ft52 Nm
Liftgate Strut2 specs
- Pinch Bolt61.2 lb-ft83 Nm
- Strut Mount Nuts38.4 lb-ft52 Nm
Torque is shown in lb-ft with Nm below it. Where a step says to turn, tighten the listed angle after the torque step before it. Use new bolts where the note says so.
Need labor times, fluids or repair steps for this car? See it on the Open Labor Project